40299291 supply of aluminium profile l=2000 mmaluminium profile l=2000 mm,aluminium profile l=2000 mm, as per drawing: lw10132 alt nil, packing instructions: pi002 [ warranty period: 30 months after the date of delivery ] => limited...
40146211 supply of aluminium profile l=2000 mmaluminium profile l=2000 mm,aluminium profile l=2000 mm, as per drawing: lw10132 alt nil, packing instructions: pi002 [ warranty period: 30 months after the date of delivery ] => limited...
39785383 supply of horizontal floor mounted ahu, frame made up of hollow extruded aluminum profile, chilled water double skin type made of 25 mm thick puf injected ( 40 kg / mm3 density ) panels consisting of g.i. casing of thickness 0.6 mm outside ( pre coated ) and 0.6 mm inside layer, complete with blower section ( didw centrifugal backward curved fan ) suitable for static pressure as detailed below, minimum 2 bend gss / pvc eliminators, cooling coil section with aluminum finned copper tubes ( tube thickness not less than 0.8 mm and dia not less than 1 / 2” ) suitable 6 row cooling coil and 2 row deep coil for heating coil with ss 304 casing, 12 fpi, filter sections with 50mm thick metal viscous / washable synthetic type air pre filters ( 90% down to 10 micron ) , electrical cable of suitable size as per ahus from panel to ahu to make it run , tefc belt driven motor suitable for 415 + 10% volts, 50hz, 3 phase, a.c supply, ss 304 drain pan duly insulated, etc. complete as per specifications and instructions of engineer in charge, of following capacities. ahu should be supplied with supply vcd. ahus must have one working and one stand by motors. ahu should be eurovent certified. makes: edgetech / zeco / systemair / wave and equivalent. motor make abb, siemens, hevels 12000 cfm / 55 mm static pressure / 26 tr cooling coil ( 4th floor ) , 12000 cfm / 55 mm static pressure / 30 tr cooling coil ( 5th floor ) , supply of the following ms class ‘c’ pipes of following diameter and of 6mtrstandard lengths for chilled water lines including insulation. insulating material should be 25mm thick nitrile insulation for chilled water pipe. insulation material should be supplied in tubular section / sheet of standard size make ms pipe tata / jindal / sail / jindal hissar 2.1 / 2 dia size ( 65 mm ) , 2 dia size ( 50 mm ) , butterfly valve supply of insulated ( 25 mm nitrile insulation ) butterfly valve ( manual ) with ci body ci disc. nitrile rubber seal & o ring pn 16 pressure rating for chilled water, complete with flanges, nut bolt etc. make audco / advance / l&t / honeywell 2.1 / 2 dia size ( 65 mm ) , 2 dia size ( 50 mm ) , pibcv valve supply of insulated ( 25 mm nitrile insulation with 26 g al cladding ) pibcv valve with ci bodyci disc. valves should have thermostat, actuators or any other accesories to run the ahus in automatic mode without bms system. make audco / advance / l&t / honeywell / danfoss / siemens 2.1 / 2 dia size ( 65 mm ) , 2 dia size ( 50 mm ) , y strainer valve supply of insulated ( 25 mm nitrile insulation with 26 g al cladding ) y strainer with ci body. nitrile rubber seal & o ring pn 16 pressure rating for chilled water. complete with flanges, nut bolt etc. make audco / advance / l&t / danfoss / s / sant / sandhu 2.1 / 2 dia size ( 65 mm ) , 2 dia size ( 50 mm ) , temperature guage supply of temperature guage suitable for measuring chilled water and hot water inlet and outlet temperatures of ahu make h guru / fiege , pressure guage supply of dial type pressure guage ( 0 10kg ) for measuring chilled water and hot water temperature at ahu inlet and outlet. make h guru / fiege , supply of auto air vents suitable for ahu mentioned at sl 1 for hot water and chilled water make anergy / castle / kartar , supply of ball valves ( ss in moc type only ) 25 mm , 10 / 12 mm , air distribution gi ducts supply of gi sheet metal of standard dimension ( 900x2500, 1000x2500, 1200x2500 ) for hvacducting work of following sizesfor supply air & return air system . the gi sheets shall be hot dip galvanized with coating of minimum 120 grams per square meter ( gsm ) of zinc. make : tata / sail / jindal / amns / asian 22 guage , 24 guage , thermal insulation supply of closed cell nitrile rubber thermal insulation class o for duct insulation of standard dimention ) . material should be supplied in rolls. make apl / aflex / kflex / armacell / aerofoam 19 mm for supply air , accoustic insulation supply of 15 mmaqua sound open cellnitrile rubber insulation of duct with standard dimension make apl / aflex / kflex / armacell / aerofoam make caryaire / dynacraft / airflow / systemair / uniaire 15 mm , accoustic insulation ( ahu room ) supply of 50mm resin bonded glass wool with 32 kg / cm3 density with 600x600 c channel of gi with aluminium perforated sheet .6 mm thick with tissue paper , fire damper supply of fire dampers for supply air duct / return air path i / c control wiring, the damper shall be motorized as required. size : 1700x500 mm fire damper make caryaire / dynacraft / airflow / systemair / uniaire actuator make danfoss / honeywell / siemens / anergy / belimo fire damper , actuator , controller , supply of canvas for connection of ahus and ducts , grills / diffusers. supplying of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. standard size 595x595 ( 375x375 neck size ) make caryaire / dynacraft / airflow / systemair / uniaire / dynamic , supply of return air diffusers of powder coated aluminium without volume control dampers anti smudge ring & removable core. standard size 595x595 ( 375x375 neck size ) make caryaire / dynacraft / airflow / systemair / uniaire / dynamic , supply fixing of powder coated extruded aluminium return air grills with louvers but without volume control damper complete as required. size make caryaire / dynacraft / airflow / systemair / uniaire / dynamic , fresh external weather louvers manufactured from 18 g gi frame complete with vcd, blades, bird screen etc. ( size 700x300 mm ) make caryaire / dynacraft / airflow / systemair / uniaire / dynamic , electrical accessories supply of wall mounted type electrical panels including system controlwiring with incoming, outgoingfeeders as described below : supply of wall mounted type electrical panels including system controlwiring with incoming, outgoingfeeders as described below : a.40a tpn mccb for 7.5 hp motor 01 set. b.ryb led type indication lights 01 set. c.vfd supply and simulation d.bypass fully automatic dol starter with built in single phasing preventer, contactor, overload relay suitable for 7.5 hp fan motor 01 set. e.auto manual type selector switch to facilitate auto start of fans after restoration ofpower 01 set. f.control wiring and safety circuit as required with start stop pbs and led type on / off indication lights. g.control wiring and safety circuit as required with start stop pbs and led type on / off indication lights. vfd make danfoss / abb / fuji / siemens panel accessories make abb / siemens / schinder / legrand / l&t , cables supply ofthe following sizes of 1.1 kv armoured xlpe insulated aluminium / copper conductor cables. cables shall be inclusive conductor cables. cables shall be inclusive of all clamps, saddles, screws, cable identification tags, insulating tapes, affectingterminal connections to the equipment as per the specifications and as required. make havells / polycab / kei 3 c x 4 sq.mm, cu , 3 c x 2.5 sq.mm, cu , 3 c x 1.5 sq.mm, flexible control cable copper , cable tray supplyingof following sizes of gi cable trays dulypainted, perforated type along with necessary elbows, bends, reducers etc. anchored along the wall / suspended from the slab / laid on terrace with necessary ms supports, anchor fasters, threaded rods etc. 150 x 50 x 1.6 mm , providing the following bare gi tape / gi wire including providing all fixing accessories & effecting proper connections. 25 x 3 gi strip , 2.5 tr fix speed splitair conditioning equipment using cfc / hcfc free refrigerant, having bee rating of minimum 3 star with outdoor stand. make hitachi, daikin, bluestar and equivalent. 4f hub room ( 1w+1s ) , 5f hub room ( 1w+1s ) , refrigerant pipe with 19 mm thick class o closed cell elastometricnitrile rubber tubular sleeves sections should be supplied seperatlyrefrigerant pipe with 19 mm thick class o closed cell elastometricnitrile rubber tubular sleeves sections should be supplied seperatly 9.5 mm , 15.88 mm , power cable 4 cx 4 sq mm between indoor and outdoor unit of standard length 90mtr , three pin top 16 amps , pvc pipe dia 25 mm for drain pipe , drain pump , supply of ss flexible hose pipe for installing fire sprinklers , supply of upright fire sprinklers , supply of ms c class pipe 25 mm dia of standard length 6 m , threaded rod 10 mm dia for duct , fasterner 10 mm for duct hilti , angle for duct support ( 40x40x3 mm ) , nut and bolts , neorine rubber self adhesive gasket for ducts ( 20 width x 3 mm thickness ) , sr 998 adhesive...
39545563 supply of aluminium profile length 2290 mm as per drg. no. t 4 4 004, alt c / 2, bright anodised conforming to specn. is:1868 1996 ( reaffirmed 2006 ) grade ac10. [ warranty period: 30 months after the date of delivery ] => limited...
39311125 supply of three type aluminium propfile, aluminium profile l=5000 mm, as per drawing: lw44173 alt a [ warranty period: 30 months after the date of delivery ] , aluminium profile l=2350 mm, as per drawing: la10131 alt a [ warranty period: 30 months after the date of delivery ] , al.profile, as per drawing: un43103 alt a, quality plan: n.a. [ warranty period: 30 months after the date of delivery ] ...
39282467 supply of aluminium profile l=2350 mm, as per drawing: la10129 alt nil [ warranty period: 30 months after the date of delivery ] => limited...
38809504 supply of 4 types of aluminium items, angle moulding, l=2m, as per drawing: cc43463 alt a, quality plan: n.a. [ warranty period: 30 months after the date of delivery ] , aluminium profile l=2000 mm, as per drawing: lw10132 alt nil, [ warranty period: 30 months after the date of delivery ] , aluminium extrusion l=1850 mm, as per drawing: cc54395 alt nil [ warranty period: 30 months after the date of delivery ] , al moulding ex j ( 2.5x12x62 ) l=1.8m, as per drawing: cc43339 alt b [ warranty period: 30 months after the date of delivery ] => limited...
38724035 supply of 04 types of aluminium items.04 types of aluminium items., al.extrusion, as per drawing: un42163. [ warranty period: 30 months after the date of delivery ] , al.extrusion l=5000 mm, as per drawing: lw44119 alt nil. [ warranty period: 30 months after the date of delivery ] , aluminium profile l=2100 mm, as per drawing: la10115 alt a. [ warranty period: 30 months after the date of delivery ] , al moulding ex flat ( 3.18x38.1 ) l=2m, as per drawing: cc43335 [ warranty period: 30 months after the date of delivery ] => limited...
38696151 supply of four type of aluminium profiles, aluminium profile l=2350 mm, as per drawing: la10131 alt a [ warranty period: 30 months after the date of delivery ] , aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil [ warranty period: 30 months after the date of delivery ] , al.profile, as per drawing: un43103 alt a, quality plan: n.a. [ warranty period: 30 months after the date of delivery ] , al profile, as per drawing: un43102 alt a, quality plan: n.a. [ warranty period: 30 months after the date of delivery ] ...
38634890 supply of aluminium profile length 2290 mm as per drg. no. t 4 4 004, alt c / 2, bright anodised conforming to specn. is:1868 1996 ( reaffirmed 2006 ) grade ac10. [ warranty period: 30 months after the date of delivery ] => limited...
38470295 supply of 04 types of aluminium items., al.extrusion, as per drawing: un42163. [ warranty period: 30 months after the date of delivery ] , al.extrusion l=5000 mm, as per drawing: lw44119 alt nil. [ warranty period: 30 months after the date of delivery ] , aluminium profile l=2100 mm, as per drawing: la10115 alt a. [ warranty period: 30 months after the date of delivery ] , al moulding ex flat ( 3.18x38.1 ) l=2m, as per drawing: cc43335 [ warranty period: 30 months after the date of delivery ] => limited...
38406938 supply of aluminium profile l=5000 mm, as per drawing: lw44173 alt a [ warranty period: 30 months after the date of delivery ] ...
38172028 supply of three type of aluminium items, aluminium extrusion for window curtain for lhb ac 3tier economy coaches, length=1200mm, as per drawing: cc54395 alt nil [ warranty period: 30 months after the date of delivery ] , aluminium profile l=2350 mm, as per drawing: la10129 alt nil [ warranty period: 30 months after the date of delivery ] , aluminium profile ( l=5000 mm ) , as per drawing: lw63105. [ warranty period: 30 months after the date of delivery ] => limited...
38097486 supply of 04 types of aluminium items., al.extrusion, as per drawing: un42163. [ warranty period: 30 months after the date of delivery ] , al.extrusion l=5000 mm, as per drawing: lw44119 alt nil. [ warranty period: 30 months after the date of delivery ] , aluminium profile l=2100 mm, as per drawing: la10115 alt a. [ warranty period: 30 months after the date of delivery ] , al moulding ex flat ( 3.18x38.1 ) l=2m, as per drawing: cc43335 [ warranty period: 30 months after the date of delivery ] => limited...
38012925 supply of aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil [ warranty period: 30 months after the date of delivery ] => limited...
37720646 supply of aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil [ warranty period: 30 months after the date of delivery ] => limited...
37691880 supply of aluminium profile l=5000 mm, as per drawing: lw44173 alt a [ warranty period: 30 months after the date of delivery ] => limited...
37675708 supply of 2 types of aluminium profile, aluminium profile l=2350 mm, as per drawing: la10131 alt a [ warranty period: 30 months after the date of delivery ] , al moulding ex uneq angle ( 2.5x35x55 ) l=1.8m, as per drawing: cc43353 alt a [ warranty period: 30 months after the date of delivery ] => limited...
37468636 supply of 2 types of aluminium profile, aluminium profile l=2350 mm, as per drawing: la10131 alt a [ warranty period: 30 months after the date of delivery ] , al moulding ex uneq angle ( 2.5x35x55 ) l=1.8m, as per drawing: cc43353 alt a [ warranty period: 30 months after the date of delivery ] => limited...
37393963 supply of aluminium profile l=5000 mm, as per drawing: lw44173 alt a [ warranty period: 30 months after the date of delivery ] => limited...
37158104 supply of aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil [ warranty period: 30 months after the date of delivery ] => limited...
37124281 supply of aluminium profile l=5000 mmaluminium profile l=5000 mm, aluminium profile l=5000 mm, as per drawing: lw44173 alt a [ warranty period: 30 months after the date of delivery ] => limited...
36822737 supply of aluminium profile ( l=5000 mm ) , as per drawing: lw63105, [ warranty period: 30 months after the date of delivery ] => limited...
36606438 supply of tools and equipment of fitter and welder trades , different profile gauges (plate type) for demonstration metric standard , knurling tool (diamond, straight & diagonal) , indexable boring bar with inserts 1 shank , machine maintenance mannual for lathe,pedestal grinder, drill machine, power saw , temperature gauge range 0 150°c , dowel pin ( straight) dia. 1 length 4 (mat:stainless steel) , standard tap screws m3, m4, m5, m6, m8, m10, m12,m14, m16 , lapping plate dia. 6 , jigs & fixture (sample) for demonstration (may be manufactured in house) , pulleys (for v belt or flat belt) to fit on 50mm dia. shaft with key slot , steel keys (may be manufactured in house) to fit with keyslot of shaft & pulley , damaged old spur gear to fit 50mm dia. shaft , v belt and flat belt to fit on pulley , packing gasket ptfe gasket roll small size , washer, clutch, keys, jib, cotter & circlip minimum 25mm size, carbon steel material , hollow punch straight shank hollow punch sets 5 12mm , drill drift (may be manufactured in house) 200mm hardened and black finish , lifting sling 8mm nominal dia. single leg sling , bearing extractor universal gear puller 2 or 3 jaws adjustable , pulley extractor universal gear puller 2 or 3 jaws adjustable , flat headed hammers with handle. , planishing hammer. , stake hatchet with leg. 300 x 200 x 20 mm , stake grooving. 100 x 100 x 300 mm , gauge snap go and not go 25 to 50 mm by 5 mm, set of 6 pieces , gauge telescopic set. 8 150 mm , dial vernier caliper. (universal type) 0 300 mm, lc 0.05 mm , screw thread micrometer with interchangeable. pitch anvils for checking metric threads 60. 0 25 mm lc 0.01 mm , digital micrometer outside. 0 25 mm l.c. 0.001 mm , comparators gauge dial indication with stand and bracket. lc 0.01mm , carbide wear block. 1 mm 2 mm , lathe tools h.s.s. tipped set. , lathe tools bit. 6 mm x 75 mm hss/carbide , lathe tools bit. 8 mm x 75 mm hss/carbide , lathe tools bit. 10 mm x 75 mm hss/carbide , arm strong type tool bit holder. 10 mm x 75 mm hss/carbide , arm strong type tool bit holder. left hand , arm strong type tool bit holder. straight , stillson wrenches 250 mm , pipe bender machine spool type with stand manually operated. up to 25 mm cold bending , adjustable pipe chain tonge to take pipes up to 300 mm , adjustable spanner. 380 mm long , compressor unit suitable for pressure: 8 bar, delivery:50 lpm (or more), reservoir capacity:24 litres (or more), 230v, 50 hz, with pressure regulator and water separator , pneumatic trainer kit, each consisting of the following matching components and accessories: , single acting cylinder max. stroke length 50 mm, bore dia 20 mm , double acting cylinder max. stroke length 100 mm, bore dia 20 mm, magnetic type , 3/2 way valve manually actuated, normally closed , 3/2 way valve pneumatically actuated, spring return , one way flow control valve , 5/2 way valve with manually operated switch , 5/2 way valve pneumatically actuated, spring return , 5/2 way pneumatic actuated valve double pilot , 3/2 way roller lever valve direct actuation normally closed , shuttle valve (or) , two pressure valve (and) , pressure gauge 0 16 bar , manifold with self closing nrv, 6 way , pushbutton station for electrical signal input with 3 illuminated momentary contact switches (1 no + 1 nc) and 1 illuminated maintained contact switch (1 no + 1 nc), contact load 2a , relay station with 3 ralays each with 4 contact sets (3no+1nc or change over type), 5 a , 3/2 way single solenoid valve with led , 5/2 way single solenoid valve with manual override and led , 5/2 way double solenoid valve with manual override and led , power supply unit, input voltage 85 265 v ac, output voltage: 24 v dc, output current: max. 4.5 a, short circuit proof. , profile plate, anodised aluminium 1100x700 mm, with carriers, mounting frames and mounting accessories (to be fitted onto the pneumatic workstation) , pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: (1) work table size(approx.) l1200mmxw900mmxh900mm, with four castor wheels including two lockable wheels at the front side, (2) drawer size (approx.) l460mmxw495mm xh158mm each,and overall size of drawer unit (approx.) l470mmxw495mmxh825mm and (3) drawer slide height (approx.) 85mm. , carrier for mounting components, such as pb & relay boxes. , cut section model for pneumatic components , hydraulic trainer kit, each consisting of the following matching components and accessories: , hydraulic power pack with (1) external gear pump having a delivery rate of 2.5 lpm, (approx.) @1400 rpm operating pressure 60 bar,coupled to a single phase ac motor (230 v ac) having start capacitor and on/off switch and overload protection, (2) pressure relief valve adjustable from 0 60 bar, (3) oil reservoir, =5 litres capacity having sight glass, drain screw, air filter, and p and t ports , pressure relief valve pilot operated , drip tray, steel size 1160 mm x 760 mm. , pressure gauge glycerin damped, indication range of:0 100 bar , four way distributor with five ports, equipped with a pressure gauge , double acting hydraulic cylinder with a control cam, piston diameter16 mm, piston rod diameter10 mm, stroke length 200 mm. , suitable weight for vertical loading of hydraulic cylinder , mounting kit for weight for realizing pulling and pushing load. , 3/2 way directional control valve with hand lever actuation , 4/2 way directional control valve with hand lever actuation. , 4/3 way directional control valve closed centre position, with hand lever actuation , non return valve. , pilot operated check valve pilot to open. , one way flow control valve with integrated check valve. , t connector with self sealing coupling nipples (2 nos.) and quick coupling socket (1 no.). , profile plate, anodised aluminium, 1100x700 mm,with carriers, mounting frames and mounting accessories (to be fitted onto the hydraulic workstation) , hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: (1) work table size(approx.) l1200mmxw900mmxh900mm, with four castor wheels including two lockable wheels at the front side, (2) drawer size (approx.) l460mmxw495mm xh158mm each, and overall size of drawer unit (approx.) l470mmxw495mmxh825mm and (3) drawer slide height (approx.) 85mm. , welding hand shield fiber , chisel cold flat 19 mm x 150 mm , centre punch 9 mm x 127 mm , stainless steel rule 300mm , scriber 150 mm double point , hack saw frame fixed 300 mm , file half round bastard 300 mm , file flat 350 mm bastard , screw driver 300mm blade and 250mm blade , magnifying glass 100 mm dia. , universal weld measuring gauge , s.s tape 5 meters flexible in case , first aid box , steel lockers with 8 pigeon holes , multiangle magnetic clamp set metal base (18x10x10 cm) , pedestal grinder fitted with coarse and medium grain size grinding wheels 300 mm dia. , bench grinder fitted with fine grain size silicon carbide green grinding wheel 150 mm dia. , ag 4 grinder , trolley for cylinder (h.p. unit) , hand shearing machine capacity cut 6 mm sheets and flats , power saw machine 18’’ or blade size 450 mm , oven, electrode drying 0 to 350°c,10 kg capacity, depth 450mm to 500 mm,intake capacity 10 kg , oxy acetylene gas cutting blow pipe , oxygen, acetylene cylinders , co2 cylinder , argon gas cylinder , swage block 5048 , magnetic particle testing kit # , fire extinguishers (foam type and co2type) , fire buckets with stand , portable abrasive cut off machine , welding simulators for smaw/gtaw/gmaw , water cooled induction welding/ brazing machine 200 250 amp., induction coil length 3 inch and 2.5 inch , plastic welding machine with hot air gun temp. display, variable temp., pe,pp& pvc sheet or pipe welding control with stand. accessories. , swaging and flooring tool kit 450 tubing 1/8 to ¾ inch , leather hand gloves 14” , cotton hand gloves 8” , s.s wire brush 5 rows and 3 rows , safety boots for welders size 7,8,9,10 , leg guards leather , rubber hose oxygen 8 mm dia x 10 mtr. long as per bis , rubber hose acetylene 8 mm dia x 10 mtr. long as per bis , arc welding single coloured glasses 108 mm x 82 mm x 3 mm. din 11a &12 a , arc welding plain glass 108 mm x 82 mm x 3 mm. , gas welding goggles with colour glass 3 or 4a din , safety goggles plain , ag 4 grinding wheels , earth clamp 600a , electrode holder 600 amps , die penetrant testing kit , anti spatter spray can 100 to 300 ml , gmaw torch nozzle tip size 0.8, 1.0, 1.2 (in mm) , tig welding torch ceramic nozzle size 3,4,5,6,8 , tungsten electrode 1.0, 1.6, 2.0 (in mm), length 150 mm , ag4 cutting wheels , ccms filler wire 1.0 mm , brass filler wire 1.0 mm , copper filler wire 1.0 mm , flux for brass , flux for copper , instructor’s table and chair (steel) , students chairs with writing pads , instructor’s laptop with latestconfiguration pre loaded with operating system and ms office package. , lcd projector with screen. , 77 inch diagonal interactive flat pannel display, smart board for education power consumption 220 300 w finger touch short panel of both side...
36539245 supply of machinery and equipments of welder fitter and rac , *ss and sc centre lathe (all geared) with minimum specification , compressor unit , pneumatic trainer kit, each consisting of the following matching components and accessories , i. single acting cylinder , ii. double acting cylinder , iii. 3/2 way valve , iv. 3/2 way valve , v. one way flow control valve , vi. 5/2 way valve , vii. 5/2 way valve , viii. 5/2 way pneumatic actuated valve , ix. 3/2 way roller lever valve , x. shuttle valve (or) , xi. two pressure valve (and) , xii. pressure gauge , xiii. manifold with self closing , xiv. pushbutton station for electrical signal input , xv. relay station , xvi. 3/2 way single solenoid valve , xvii. 5/2 way single solenoid valve , xviii. 5/2 way double solenoid valve , xix. power supply unit , xx. profile plate, anodised aluminium , pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide , hydraulic trainer kit, each consisting of the following matching components and accessories: , i. hydraulic power pack , ii. pressure relief valve , iii. drip tray, steel , iv. pressure gauge , v. four way distributor , vi. double acting hydraulic cylinder , vii. suitable weight , viii. mounting kit for weight , ix. 3/2 way directional control valve , x. 4/2 way directional control valve w , xi. 4/3 way directional control valve , xii. non return valve , xiii. pilot operated check valve , xiv. one way flow control valve , xv. t connector with self sealing coupling nipples (2 nos.) and quick coupling socket (1 no.). , xvi. profile plate, , hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: , cut section models for hydraulic components , suitable arc welding table with positioner , power saw machine , water cooled induction welding/brazing machine , c.r.o single beam , c.r.o dual trace/ double beam , single door direct cool refrigerator, carrying with hfc and hc , frost free refrigerator , three/four door refrigerator ( inverter type) , window a.c , split a.c , duct able split a.c 1.5 ton , shell and tube, dx chillers (small) , display cabinet , water cooler storage type , bus ac tutorial model , automatic ice cube m/c , storage type water cooler( hot and cold) , vrf/vrv unit with two indoor units 2.5tr each and 5tr capacity out door unit complete with air cooled condenser, accessories and controls. , split a/c ( inverter technology) , walk in cooler puf insulated for cold room 6x4.5x8 cft. , absorption system , work bench...
36532534 supply of aluminium profile ( l=5000 mm ) , as per drawing: lw63105, [ warranty period: 30 months after the date of delivery ] => limited...
36501956 supply of al.extrusion l=3800mm aluminium profile l=5000 mmal.extrusion l=3800mm aluminium profile l=5000 mm, aluminium profile l=5000 mm, as per drawing: lw44173 alt a [ warranty period: 30 months after the date of delivery ] , al.extrusion l=3800mm, as per drawing: lw44114 alt c, quality plan: n.a. [ warranty period: 30 months after the date of delivery ] => limited...
36421660 supply of machinery and equipment procurement of machinery and equipment , anti theft device , fuel injection pump, ve pump / distributor fuel rotary pump ( dpc ) pumps / along with special tools and accessories. , functional / experiment model of different type of sensors. , granite surface plate 1600 x1000 with stand and cover , steering assembly 1.rack& pinion, 2.worm& roller3.recirculating ball, 4.powersteering , air bag simulator , air conditioned crdi vehicle in running condition lmv , air conditioning service unit ( car ) , four stroke petrol engine with cng setup working condition , mpfi petrol engine with swiveling stand along with special tools for dismantling and assembling , multi scan tool with oscilloscope , ultra sonic injection cleaning equipment , lcd prjector / led / lcd tv ( 42 inch ) , ss and sc centre lathe ( all geared ) , pillar type drilling machine , compressor unit , pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: , carrier for mounting components, suchas pb & relay boxes , cut section model for pneumatic components , hydraulicworkstationwith40square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: , cut section models for hydraulic components...
36041272 supply of aluminium profile ( l=5000 mm ) , as per drawing: lw63105, [ warranty period: 30 months after the date of delivery ] => limited...
35916245 supply of tools and equipment of different trades 1 compressor unit 2 pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 3 carrier for mounting components, suchas pb & relay boxes. 4 cut section model for pneumatic components 5 hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 6 cut section models for hydraulic components 7 spirit level metal type 2300 mm basic length accuracy .1mm / meter 8 stud extractor ezy – out set of 8 9 marking table ( mild steel ) 900x900x900 mm 10 machine vice swivel base100 mm 11 machine vice swivel base125 mm 12 power tools for fastening capacity 10 18mm 13 different profile gauges ( plate type ) for demonstration metric standard 14 indexable boring bar with inserts inserts1 shank 15 machine maintenance manual for lathe, pedestal grinder, drill machine, power saw 16 temperature gauge 0 150°c 17 dowel pin ( straight ) dia. 1” length 4 ( mat: stainless steel ) 18 standard tap screws m3, m4, m5, m6, m8, m10, m12, m14, m16 19 lapping plate dia. 6 20 medium carbon heat treated alloy steel metric studs and bolts along with nuts ( for display ) of standard length ( may be manufactured in house ) m6, m8, m10, m12, m14, m16 ( standard ) 21 caps screws m6, m8, m10, m12 22 cast iron globe valve ( flanged type ) 150nb, class# 150 flange:ansi125 b16.1 23 c.i. sluice / gate valve ( flanged type ) 150nb, class# 150 flange:ansi125 b16.1 24 stop cock25nb ( 2 way, threaded end ) 25 slip on forged steel flange150nb, ansi b16.5, class#150 26 bolt & nut with washer ( may be manufactured in house ) m20x2.5x90long ( part thread hex. head ) 27 jigs & fixture ( sample ) for demonstration ( may be manufactured in house ) 28 pulleys ( for v belt or flat belt ) to fit on 50mm dia. shaft with key slot 29 steel keys ( may be manufactured in house ) to fit with key slot of shaft & pulley 30 damaged old spur gear to fit 50mm dia. shaft 31 v belt and flat belt to fit on pulley 32 packing gasket ptfe gasket roll small size 33 washer, clutch, keys, jib, cotter &circlip minimum 25mm size, carbon steel material 34 drill drift ( may be manufactured in house ) 200mm hardened and black finish 35 bearing different types each type of diameter 25mm ( min. ) 36 lifting sling 8mm nominal dia. single leg sling 37 bearing extractor universal gear puller 2 or 3 jaws adjustable 38 pulley extractor 39 digital vernier caliper.0 150 mm with least count 0.02mm 40 stand and bracket. 41 surface roughness comparison platesn1 n12 grade 42 flat rough file12 43 flat second cut file 12 44 flat bastard file 12 45 flat smooth file 12 46 triangular file second cut 12 47 square file 8 48 round file 12 49 half round file second cut 12 50 half round file second cut 8 51 round file second cut 8 52 measuring steel tape 5 meter 53 combination plier insulated200 mm 54 screwdriver insulated4mmx 150 mm, diamond head 55 screwdriver insulated6mmx 150 mm 56 electrician screwdriver thin stem insulated handle4mmx 100 mm 57 heavy duty screwdriver insulated5mmx 200 mm 58 electrician screwdriver thin stem insulated handle4mm x 250 mm 59 punch centre9mm x 150 mm 60 knife double bladed electrician100 mm 61 neon tester500 v 62 steel rule graduated both in metric and english unit300 mm with precision of 1 / 4th mm 63 hammer, cross peen with handle250 grams 64 hammer, ball peen with handle500 grams 65 pincer150 mm 66 c clamp200 mm and 100 mm 67 spanner adjustable drop forged, ss150 mm & 300mm 68 blow lamp brass0.5 ltr 69 chisel cold25 mm x 200 mm 70 chisel firmer with wooden handle6 mm x 200 mm 71 allen key alloy steel1.5 10 mm ( set of 9 ) 72 grease gun0.5 ltr. capacity 73 bradawl 74 pully puller with 3 legs150 mm & 300mm 75 bearing puller ( inside and outside ) 200 mm 76 pipe vice cast iron with hardened jaw open type100 mm 77 scissors blade, ss 200mm 78 scissors blade, ss150 mm 79 crimping tool1.5 sq mm to 16 sq mm & 16 sq mm to 95 sq mm 80 wire cutter and stripper150 mm 81 mallet hard wood0.50 kg 82 hammer extractor type250 grams 83 hacksaw frameadjustable 300 mm fixed 150 mm 84 try square150 mm blade 85 outside calliper150 mm spring type 86 inside calliper150 mm spring type 87 divider150 mm spring type 88 pliers long nose insulated150 mm 89 pliers flat nose insulated200 mm 90 pliers round nose insulated100 mm 91 tweezers150 mm 92 snip straight and bent heavy duty250 mm 93 d.e. metric spanner double ended6 32 mm 94 drill hand brace0 100mm 95 drill s.s. twist block2 mm, 5 mm and 6 mm set of 3 96 plane cutters50 mm x 200mm 97 smoothing cutters50 mm x 200mm 98 gauge, wire imperial stainlees steel marked in swg & mmwire gauge metric 99 file flat200 mm 2nd cut with handle 100 file flat rough150 mm with handle 101 file flat bastard250 mm with handle 102 file flat smooth250 mm with handle 103 file rasp, half round200 mm bastard with handle 104 copper bit soldering iron.0.25 kg 105 de soldering gunheat proof nozzle, pvc type, 250mm 106 hand vice50 mm jaw 107 table vice100 mm jaw 108 oil can250 ml 109 contactor & auxiliary contacts3 phase, 415 volt, 25 amp with 2 no and 2nc 110 contactor & auxiliary contacts.3 phase, 415 volt, 32 amp with 2 no and 2 nc 111 limit switchlimit switch, liver operated 2a 500v, 2 contacts 112 rotary switch16 a / 440v 113 relay a. cut out relays b. reverse current c. over current d. under voltagea. 16a, 440v b. 16a, 440v c. 16a, 440v d. 360v 440v 114 pin type, shackle type, egg type & suspension type insulators including hardware fitting 115 hydrometer 116 hand drill machine0 6 mm capacity 117 portable electric drill machine0 12 mm capacity 750w, 240v with chuck and key 118 load bank ( lamp / heater type ) 6 kw, 3ph 119 brake test arrangement with two spring balance rating0 to 25 kg 120 laboratory type induction coil1000 w 121 out side micrometer0 25 mm least count 0.01mm 122 thermometer digital0° c 150° c 123 series test lamp230v, 60w 124 knife switch dpdt fitted with fuse terminals16 amp 125 knife switch tpdt fitted with fuse terminals16 amp / 440 v 126 miniature breaker16 amp 127 earth plate60cm x 60cm x 3.15mm copper plate 60cm x 60cm x 6mm gi plate 128 earth electrodeprimary electrode 2100x28x3.25mm secondary cu strip 20x5mm 129 mccb100amps, triple pole 130 elcb and rccb25amps, double pole and 25amps, double pole, iδn 30 ma 131 fuseshrc glass rewire type 132 rheostat ( sliding type ) 0 25 ohm, 2 amp 0 300 ohm, 2 amp 0 1 ohm, 10amp0 10 ohm, 5 amp 133 capacitorselectrolytic ceramic polyester film variable dual run 134 various electronic componentsresistors, diode, transistor, ujt, fet, scr, diac, traic, igbt, small transformer etc. 135 various lampshalogen incandescent lamp fluorescent tube hp mercury vapor lamp high pressure sodium lamp low pressure sodium lamp led 136 plug socket piano switch lamp holder230 v, 5 a 137 cables: twisted pair non metallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi conductor cable coaxial cable direct buried cable1 mtr each 138 bus bar with brackets1 mtr each 139 rubber mat2’ x 4’ x 1” 140 electrician helmetyellow colour 141 rcc pole with accessories ( ms angle iron, ‘c’ clamp, stay insulator etc. ) and materials6 mtr 142 safety beltstandard quality 143 ohm meter; series type & shunt type, portable box type50 / 2000 ohm analog 144 digital multi meterdc 200mv 1000v, 0 – 10a & ac 200mv 750v , 0 10a, resistance 0 20 mω and3 1 / 2 digit 145 a.c. voltmeter m.i.analog, portable box type housed in bakelite casemulti range 75 v 150v 300v 600v 146 milli voltmeter centre zero analog, portable box type housed in bakelite case100 – 0 – 100 mv 147 ammeter mc analog, portable box type housed in bakelite case0 500 ma, 0 5 a, 0 25 a 148 ac ammeter mi, analog, portable box type housed in bakelite case0 1 a, 0 5 a, 0 25 a 149 kilo wattmeter analog0 1.5 3kw, pressure coil rating 240v / 440v, current rating 5a / 10a analoge, portable type housed in bakelite case 150 digital wattmeter230 v, 1 kw, 50 hz 151 a.c. energy metersingle phase, 10 a, 240 v induction type 152 a.c. energy meterthree phase, 15 a , 440 v induction type 153 power factor meter digital440v, 20a, threephaseportable box type 154 frequency meter45 to 55 hz 155 magnetic flux meter0 500 tesla 156 lux meterlux meter lcd read out 0.05 to 7000 lumens with battery. 157 tachometeranalog type 10000 rpm 158 tachometerdigitalphotosensortype 10000 rpm 159 tong tester / clamp meter0 100 a ( digital type ) 160 meggeranalog 500 v 161 3 point d.c. starterfor 2.5 kw dc motor 162 4 point d.c. starterfor 2.5 kw dc motor 163 wheat stone bridge with galvanometer and battery 164 single phase variable auto transformer0 270 v, 10amp ( air cooled ) 165 single phase variable auto transformer1 270 v, 15amp ( air cooled ) 166 phase sequence indicator3 phase, 415 v 167 growler230 v, 50 hz, single phase, adjustable jaws, testing armature with ampere meter and testing probes. 168 ac starters: a. resistance type starter b. direct on line starter c. star delta starter manual d. star delta starter – semi automatic e. star delta starter – fully automatic f. star delta starter soft starter g. auto transformer type 169 function generator2 to 200 khz, sine, square, triangular 220 v, 50 hz, single phase 170 soldering iron25 watt, 65 watt and 120 watt, 230 volt 171 temperature controlled soldering iron50 watt, 230 volt 172 discrete component trainerdiscrete component ( for diode and transistor circuit ) with regulated power supply +5, 0 5 v, +12 , 0 12 v 173 linear i.c. trainerlinear i.c. trainer with regulated power supply 1.2v to 15v pic socket 16pin and 20 pins with bread board 174 digital i.c. trainerdigital i.c. trainer 7 segment display and bread board 175 electric induction platea. 1500 watt, 240v 176 electric kettleb. 1500 watts, 240v 177 electric ironc.automatic 750 w, 240 v 178 immersion heaterd. 1500 watt, 240v 179 a.c. ceiling fan and ac table fane. 68 watt, 230 v 180 geyser ( storage type ) f.10 litre 181 mixture & grinderg. 750 w, 240 v 182 washing machine semi automatich. 5 kg, 183 motor pump seti. 1 hp, 1 phase, 240 v 184 oil testing kitoil testing kit 230 v, single phase 50 hz60 va output 0 60 kv variable 185 inverter with battery1 kva with 12 v battery input 12 volt dc, output 220 volt ac 186 voltage stabilizerac input 150 250 v, 600 va ac output 240 v, 10 a r 187 dc power supply0 30 v, 5 a 188 battery charger0 6 9 12 24 48 v, 30amp 189 current transformer415 v, 50hz, ct ratio 25 / 5 a, 5va 190 potential transformer415 v, 50hz, pt ratio, 440v / 110v, 10va 191 solar panel with battery18 watt 192 ink jet / laser printer 193 fire extinguisher co22 kg 194 fire bucketsstandard size 195 soldering iron changeable bits15 watt, 240 volt 196 magneto spanner set8 spanners 197 scissors200mm 198 hand drill machine electric with hammer action13mm 199 clamp meter0 10a 200 milli ammeter ( ac ) 0 200ma 201 milli ammeter ( dc ) 0 500mar 202 allen key screwdriver5 no. of set 203 solar training kit / simulatorwith built in meters for dcv, dca, ac multifunction meter ( for aci, acv, power, frequency ) , protection circuits, bs 10 terminals for making the connection, single / dual axis tracking system charge controller: pwm based mppt, charging stage: bulk, absorptions and float 204 led lighting systemmeasurement of power, voltage, current, power factor and light output performance of different lighting products like led, cfl at variable input voltages 0 to 245v variable ac 205 petrol engine ( 2 stroke ) motor cycle / scooter along with special tools and 206 welding process inspection and code 207 leather hand gloves 208 cotton hand gloves 209 leather appron 210 leather hand sleeve 211 rubber hose clip 212 arc welding cabel copper 213 arc welding plain glass 214 gass welding goggle 215 spark lighter 216 ups 217 gas welding plant with oxy / acthylene cylinder 218 electric drill6 mm capacity 219 portable circular saw machine 220 portable sander machine200mm dia 221 power screw driver 222 circuar saw machine 3 mm dia300 mm dia 223 set of turning tools for above lathe machine 224 portable discsander 200mm dia 225 angle plate size200×100×200 226 granite surface plate with stand and cover 227 oil stone 228 sprit level 229 adze15 kg 230 small type compressor with spry painting gun...
35855899 supply of machinery and equipment of various trades 2 pulley puller with 3legs 3 bearing puller ( inside and outside ) 4 caliper outside spring joint 5 caliper inside spring joint 6 scriber 7 centre punch 8 prick punch 9 divider spring joint 10 safety goggles clear glass ( good quality ) 11 file flat 12 file flat 13 wheel dresser diamond 14 temperature gauge ( digital ) 15 magnifying glass 16 tachometer ( counting type ) 17 gauge telescopic 18 file half round 19 vernier bevel protractor 20 tap &die set 21 machine vice swivel base 22 fire buckets 23 screw driver 24 welding helmet fiber 25 chipping hammer with metal handle 250grams 26 stainless steel rule 300mm 27 spannerd.e, 6mm to 32mm ( set of 12 pieces ) 28 hacksaw frame fixed 300mm 29 file half round bastard 300mm 30 file flat 200mm bastard 31 file flat 350mm bastard 32 hammer ball pane 1kg with handle 33 tip cleaner 34 trysquare6 35 flash back arrester ( torch mounted ) 36 flash back arrester ( cylinder mounted ) 37 auto darkening welding helmet 38 swage block 39 leg guards leather 40 ag4 grinding wheels 41 measuring steel tape 42 combination plier insulated 43 screw driver insulated 44 electrician screw driver thin stem insulated handle 45 heavy duty screw driver insulated 46 electrician screw driver thin stem insulated handle 47 knife double bladed electrician 48 punch centre 49 hammer, cross peen with handle 50 c clamp 200 mm 3 and 100 mm 3 51 spanner adjustable drop forged, ss 52 scissor sblade, ss 53 scissors blade, ss 54 crimping tool 55 crimpingtool 56 wire cutter and stripper 57 hacksaw frame 58 pliers long nose insulated 59 plane cutters 60 gauge, wire imperial stainlees steel marked in swg & mm 61 table vice 62 oil can 63 contactor & auxiliary contacts 64 contactor & auxiliary contacts. 65 relay a. cut out relays 4, b. reverse current 4, c. over current 4, d. under voltage 4 66 insulators including hardware fittingpin type 4, shackle type 4, egg type 4 &suspension type 4 67 load bank ( lamp / heater type ) 68 brake test arrangement with two spring balance rating 69 knife switch dpdt fitted with fuse terminals 70 knife switch tpdt fitted with fuse terminals 71 earth plate ( 60cm x 60cm x 3.15mm copper plate 2, 60cm x 60cm x 6mm gi plate 2 72 earth electrode 73 mccb 74 elcb 4 and rccb 4 ( 25amps, double pole and 25amps, double pole, iδn 30 ma, isi marked ) 75 fuses 76 fuses 77 bus bar with brackets 78 rubber mat 79 electrician helmet 80 rcc pole with accessories ( ms angle iron, ‘c’ clamp, stay insulator etc. ) and materials 81 safety belt 82 ohm meter; series type 4 & shunt type 4, portable box type 4 83 digital multi meter 84 a.c. voltmeter m.i.analog, portable box type housed in bakelite case 85 milli voltmeter centre zero analog, portable box type housed in bakelite case 86 ammeter mc analog, portable box type housed in bakelite case ( 0 500 ma 4no, 0 5 a 4no, 0 25 amp 4no ) backlite body, knife edge , p ointer & anti parallex mirror accuracy – 0.5 % 87 ac ammeter mi, analog, portable box type housed in bakelite case ( 0 1 a 4no, 0 5 a 4no, 0 25 a 4no backlite body, knife edge , pointer & anti parallex mirror accuracy – 0.5 % ) 88 digital wattmeter 89 a.c. energy meter 90 a.c. energy meter 91 power factor meter digital 92 magnetic flux meter 93 lux meter 94 phase sequence indicator 95 temperature controlled soldering iron 96 discrete component trainer 97 digital i.c. trainer 98 domestic appliances – electric induction plate 99 domestic appliances – a.c. ceiling fan 1 and ac table fan 2 100 domestic appliances – geyser ( storage type ) 101 domestic appliances – mixture & grinder 102 domestic appliances – washing machine semi automatic 103 oil testing kit 104 inverter with battery 105 potential transformer 106 solar panel with battery 107 ink jet / laser printer 108 working bench 109 metal rack 110 lockers with drawers 111 fire extinguishers 112 first aid box 113 drill machine12mm capacity 114 foot rule steel tape 115 marking knife, 200 mm 116 carpenter square, 200 mm 117 square, bevel, 200 mm 118 carpenter marking gauge. 119 carpenter mortise gauge 120 saw hand, 450mm 121 saw tenon, 300mm 122 plane jack metal, 335 x50 mm cutter 123 plane smoothing metal, 200x50 mm cutter 124 chisel mortise 6, 10, 15, mm ( 3 no’s ) 125 screwdriver ( cabinet maker ) , 300 mm 126 mallet medium size 127 hammer claw, 500 gm 128 oil stone ( carborundum ) , ( universal silicon carbide combination rough and fine ) , 200 x 50 x 21 mm 129 hand brush for bench cleaning ( 450mm ) 130 router plane 131 file slim taper 100mm 132 file slim taper 150mm 133 centre bits 6, 8, 10, 12 mm 134 combinationcutting pliers 135 plunger saw set / pistol grip type 136 electric blower 137 steel locker, 8 compartment with individual locks 138 stool 139 portable circular saw machine 140 power drill machine 6mm capacity 141 power screw driver 142 set of turning tools. 143 portable electric drill 144 drill chuck 12 mm capacity 145 portable disc sander 200 mm dia 146 electric heater, 1000 / 1500 w 147 electrical drying oven ( small type ) 148 cd 1 & dvd 1 of different joint related to carpenter works and variety design of modern furniture 149 co2 gas pressure regulator wigh flow meter 150 argon gas pressure regulator with flow meter 151 multiangle magnetic clamp set 152 swaging and flooring tool kit 450 tubing 153 gas welding goggles with colour glass 3 or 4a din 154 anti spatter spray can 155 gmaw torch nozzle tip 156 tig welding torch ceramic nozzle 157 tungsten electrode 158 ag4 cutting wheels 159 students chairs with writing pads 160 welding process, inspection & codes dvd / cds 161 welding hand shield fiber 162 chisel cold flat 19 mm x150mm 163 centre punch 9 mmx127 164 dividers 200 mm 165 scriber 150 mm double point 166 flat tongs 350 mm long 167 anvil 24 sq.inches working area with stand 168 leather hand gloves 14 169 cotton hand gloves 8” 170 leather hand sleeves 16” 171 leather apron leather 172 wire brush ( ms & ss ) 5 rows 4noand 3 rows 4no 173 safety boots for welders 7, 8, 9, 10 174 arc welding single coloured glasses 108 mm x 82 mm x 3 mm. din 9a 20no, 11a 20no &13 a 20no 175 bubble face shield clear with rubber band 176 dye penetrant testing kit ( set ) 177 centre punch 178 file half round second cut 179 marking table ( mild steel ) 180 drill twist straight shank ( 3 to 12 mm by 0.5 mm h.s.s ) 181 drill twist taper shank ( 8 mm to 20 mm by ½ mm h.s.s ) 182 taps and dies complete set in box ( wit worth.material high carbon steel ( isi ) 0 to 12 number ) 183 file knife edgesmooth 184 file feather edge 185 file roundsecond cut 186 file squaresecond cut 187 file triangularsecond cut. 188 file flatsecond cut safe edge 189 file half round bastard. 190 file roundbastard. 191 file handsecond cut. 192 card file. 193 wooden handle forged soldering iron copper bit. 194 blow lamp 195 interchangeable ratchet socket set ( 12 mm driver, sized10 32 mm set of 18 socket & attachments. ) 196 double ended tubular box spanner set with tommy bar ( a / f 6 25 mm set of 10 tommy bar dia 6, 8, 10, 12, 14, 16 ) 197 clamp toolmaker . 198 hand reamer set ( tapar pin straight flute ) nominal dia 6, 8, 10, 12, 16mm 199 machine reamer parallel ( helical flute ) 12 16mm set of 5 200 scraper flat 201 chisel coldcross cut 8no & diamond.point 8no 202 chisel coldround noze. 203 pipe wrench 204 machine vice swivel base 205 machine vice 206 power tools for fastening 207 different profile gauges ( plate type ) for demonstration 208 knurling tool ( diamond 1, straight 1 & diagonal 1 ) 209 indexable boring bar with insert 210 machine maintenance manual for lathe 1, pedestal grinder 1, drill machine 1, power saw 1 211 dowel pin ( straight ) 212 standard tap screws ( m3 1no, m4 1no, m5 1no, m6 1no, m8 1no, m10 1no, m12 1no, m14 1no, m16 1no ) 213 lapping plate 214 caps screws ( m6 2no, m8 2no, m10 2no, m12 2no ) 215 drill gauges ( letter drill gauge ( a to z ) 2no , number drill gauge ( 1 to 60 ) 2no , metric drill gauge ( 1.5mm to 12.5mm, 30 holes 2no ) 216 cast iron globe valve ( flanged type ) 217 c.i. sluice / gate valve ( flanged type ) 218 stop cock 219 m.s. pipe ( 150nb, sch.40, erw, is:1239 9feet ) 220 g.i. pipe 221 slip on forged steel flange 222 pipe threading die with handle 223 pulleys ( for v belt 1, flat belt 1 ) 224 damaged old spur gear 225 v belt 1 and flat belt 1 226 packing gasket 227 washer 2nos., clutch 2nos., keys 2nos., jib 2nos., cotter 2nos. & circlip 2nos. 228 bearing different types 229 lifting sling 230 gauge snap go and no go ( 25 to 50 mm by 5mm. set of 6 pcs. ) 231 gauge plug ( single 3 ended 5 to 55 by 5 mm. set of 11 pcs. ) 232 dial vernier caliper 233 screw thread micrometer with interchangeable . pitch anvils for checking metric threads 60. 234 digital micrometer out side 235 engineer’s try square ( knife wedge ) 236 pipe bender spool typewith stand manually operated. 237 adjustable pipe chain tonge to take pipes . 238 adjustable spanner 239 pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 240 carrier for mounting components, such as pb & relay boxes. 241 cut section model for pneumatic components 242 hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 243 cut section models for hydraulic components 244 neon tester 245 smoothing cutters 246 de soldering gun 247 rotary switch 248 laboratory type induction coil 249 tong tester / clamp meter 250 megger 251 function generator 252 linear i.c. trainer 253 dc power supply 254 battery charger 255 pully puller with 3 legs 256 drill hand brace 257 drill s.s. twist block 258 file flat 259 file half round 260 out side micrometer 261 thermometer digital 262 wheat stone bridge with galvanometer and battery 263 domestic appliances – motor pump set 264 synchronous motor with accessories like starter, excitation arrangements. 265 thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement 266 thyristor / igbt controlled a.c. motor drive with 267 single phase transformer, core type, air cooled 268 three phase transformer, shell type oil cooled with delta / star 269 useddc generators series 1, shunt 1 and compound type 1 for overhauling practice 270 ceiling fan coil winding machine 271 stepper motor with digital controller 272 shaded pole motor 273 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 274 rheostat ( sliding type ) ( 0 25ohm ) 1, ( 0 300 ohm ) 1 275 protractor celluloid 276 scale card board 277 scales plotting box 278 set square transparent 279 set square celluloid 280 t square 1250mm / mini drafter / parallel bar 281 template –architects and builders 282 geometrical models ( wooden / plastic ) 283 templates – circle, ellipse, furniture, etc. 284 steel arrow, wooden peg, wooden mallet, hammer 285 printer ( desk jet / laser jet ) with scanner ( multipurpose ) 286 server work station with latest configuration 287 broad band connection 288 furniture for server, printer, plotter 289 white board ( 6’ x 4’ ) 290 screen for projector ( motorized ) 291 wall clock 292 steel cupboard 120 x 60 x 45 cm 293 book shelf 294 trainer’s / instructor’s table ( big size full secretariat ) ( 6 feet x 4 feet ) 295 allen key set of 12 pieces ( 2mm to 14mm ) 296 electrician screw driver 250mm 297 hammer ball peen 0.5 kg with handle 298 hands file 20 cm. second cut flat 299 philips screw driver set of 5 pieces ( 100 mm to 300 mm ) 300 screw driver 20cm.x 9mm. blade 301 screw driver 30 cm. x 9 mm. blade 302 spanner, ring set of 12 metric sizes 6 to 32 mm. 303 spanners socket with speed handle, t bar, ratchet and universal upto 32 mm set of 28 pieces with box 304 adjustable spanner ( pipe wrench 350 mm ) 305 air blow gun with standard accessories 306 air impact wrench with standard accessories 307 air ratchet with standard accessories 308 allen key set of 12 pieces ( 2mm to 14mm ) 309 alternator for tractor – different type 310 ammeter 300a / 60a dc with external shunt 311 angle plate adjustable 250x150x175 312 angle plate size 200x100x200mm 313 anvil 50 kgs with stand 314 arbor press hand operated 2 ton capacity 315 auto electrical test bench 316 battery –charger 317 belt tensioner gauge 318 blow lamp 1 litre 319 car jet washer with standard accessories 320 chain pulley block 3 ton capacity with tripod stand 321 chaser hard w / v 9 to 40 t.p.i. set of 11 external. 322 chaser, hand w / w 9 to 40 t.p.i. set of 11 internal. 323 chisel 10 cm flat 324 chisels cross cut 200 mm x 6mm 325 circlip pliers expanding and contracting type 15cm and 20cm each 326 clamps c 150mm 327 cleaning tray 45x30 cm. 328 clutches, different types such as cone type 1, disc type 1 329 compression testing gauge suitable for diesel engine 330 connecting rod alignment fixture 331 copper bit soldering iron 0.25 kg 332 cut section model of fuel filter 333 cylinder bore gauge capacity 20 to 160 mm 334 cylinder liner dry 1no & wet liner 1no, press fit 1no& slidefit liner 1no 335 depth micrometer 0 25mm 336 dial gauge type 1 gr. a ( complete with clamping devices and stand ) 337 different type of engine bearing model ( shell bearing, ball bearing, needle bearing ) 3pieces set 338 different type of piston model ( concave head, swilling chamber, discadr type head ) 3pieces set 339 drift punch copper 15 cm 340 drift, copper 10 x 15 1 / 2 mm 341 drill point angle gauge 342 drill twist 1.5 mm to 15 mm ( various sizes ) by 0.5 mm 343 electric soldering iron 230 v 60 watts 2no, 230 v 25 watts 2no 344 electric testing screw driver 345 engineer’s square 15 cm. blade 346 engineers stethoscope 347 equipment puncture, in box, 348 feeler gauge 20 blades ( metric ) 349 file, square 20 cm second cut 350 file, square 30 cm round 351 file, triangular 15 cm second cut 352 files assorted sizes and types including safe edge filecarbon steel ( 5 cm 25cm ) ( set of 20 nos ) 353 flat file 35 cm bastard 354 glow plug tester 355 granite surface plate 1600 x 1000 with stand and cover 356 grease gun 357 grover – 3mm 1no, 4mm 1no, 6mm 1no. 358 growler 359 hacksaw frame adjustable 20 30 cm 360 hammer ball peen 0.75 kg 361 hammer chipping 0.25 kg 362 hammer copper 1 kg with handle 363 hammer mallet 364 hand operated crimping tool ( i ) for crimping up to 4mm and ( ii ) for crimping up to 10mm 365 hand reamers adjustable ( 10.5 to 11.25 mm, 11.25 to 12.75 mm, 12.75 to 14.25 mm and 14.25 to 15.75 mm ) set of 4 366 hand shear universal 250mm 367 hand vice – 37 mm 368 hollow punch set of seven pieces 6mm to 15mm 369 hydraulic jack hi lift type 3 ton capacity, 370 injector – multi hole type, pintle type 371 injector cleaning unit 372 insulated screw driver 20 cm x 9mm blade 373 insulated screw driver 30 cm x 9mm blade 374 lifting jack screw type 3 ton capacity 375 magneto spanner set with 8 spanners 376 marking out table 90x60x90 cm. 377 multi scan tool 378 oil pump for dismantling and assembling. 379 oil stone 15 cm x 5 cm x 2.5 cm 380 oscilloscope 20mhz 381 outside micrometer 0 to 25 mm 382 outside micrometer 25 to 50 mm 383 outside micrometer 75 to 100 mm 384 philips screw driver set of 5 pieces ( 100 mm to 300 mm ) 385 pipe cutting tool 386 pipe flaring tool 387 piston ring expander and remover. 388 piston ring groove cleaner. 389 pliers flat nose 15 cm 390 pliers round nose 15 cm 391 pliers side cutting 15 cm 392 portable electric drill machine 393 portable oil monitoring indicator 394 power supply 0 12 v, lamp 395 punch letter 4mm 396 radiator cut section cross flow 397 radiator cut section down flow 398 radiator pressure cap 399 rake 400 rear axle assembly gear box steering box assembly of the diesel engine 401 ridger. 402 rivet sets snap and dolly combined 3mm, 4mm, 6mm 403 scraper flat 25 cm 404 scraper half round 25 cm 405 scraper triangular 25 cm 406 scriber 15 cm 407 scriber with scribing black universal 408 set of stock and dies unc, unf and metric ( 5mm to24 mm h c s ) 409 soldering copper hatchet type 500gms 410 spanner clyburn 15 cm 411 spanner t. flocks for screwing up and up screwing inaccessible positions 412 spanner, adjustable 15cm. 413 spanner, ring set of 12 metric sizes 6 to 32 mm. 414 spanners socket with speed handle, t bar, ratchet and universal upto 32 mm set of 28 pieces with box 415 spirit level 2v 250, 05 metre 416 spring tension tester 417 stake grooving. 418 stake, hatchet. 419 steel measuring tape 10 meter in a case 420 steel rule 15 cm inch and metric 421 steel rule 30 cm inch and metric 422 steel wire brush 50mmx150mm 423 stone, carborandum 15 x 5 x 4 cm smooth 1no and rough 1no. 424 straight edge gauge 2 ft. 425 straight edge gauge 4 ft. 426 stud extractor set of 3 427 stud remover with socket handle 428 surface gauge with dial test indicator plunger type i.e. 0.01 mm 429 taps and wrenches – metric ( 5mm to24 mm h c s ) 430 thermostat 431 thread pitch gauge metric, bsw 432 torque wrenches 5 35 nm 1no, 12 68 nm 1no& 50 225 nm 1no 433 trammel 30 cm 434 turbocharger cut sectional view 435 tyre pressure gauge with holding nipple 436 universal puller for removing pulleys, bearings 437 v’ block 75 x 38 mm pair with clamps 438 vacuum gauge to read 0 to 760 mm of hg. 439 valve lifter 440 valve spring compressor universal. 441 vernier caliper 0 300 mm with least count 0.02mm 442 vice grip pliers 443 voltmeter 50v / dc 444 water pump for dismantling and assembling 445 arbor press hand operated 2 ton capacity 446 automotive exhaust 5 gas analyzer ( petrol & diesel ) or diesel smoke meter 447 bench lever shears 250mm blade x 3mm capacity 448 discrete component trainer / basic electronics trainer 449 gas welding table 1220mm x760mm 450 multi scan tool 451 p.t.o. operated rotary lawn mower 452 pneumatic rivet gun 453 spring tension tester 454 welding plant oxy acetylene complete ( high pressure ) 455 book shelf ( glass panel ) 6½ ‘ x 3’ x 1½’ 456 computer chair 457 computer table 458 desktop computer and related ms office software 459 discussion table 8’ x 4’ x 2½ ‘ 460 fire extinguishers, first aid box 461 instructional material – nimi books / ref.books as required 462 internet connection with all accessories 463 laser printer 464 lcd projector / led / lcd tv ( 42” ) 465 multimedia dvd for automotive application / subjects 466 online ups 2kva 467 stools 468 storage rack 6½ ‘ x 3’ x 1½’ 469 storage shelf 6½ ‘ x 3’ x 1½’ 470 tool cabinet 6½ ‘ x 3’ x 1½’ 471 trainees locker 6½ ‘ x 3’ x 1½’ 472 caliper odd leg firm joint 473 steel rule 474 hammer ball peen 475 chisel cold flat 476 hammer copper / brass 477 hacksaw fixed 478 file flat 479 file round 480 file half round 481 combination set 482 pliers flat nose 483 micrometer inside 484 vernier micrometer 485 vernier micrometer 486 vernier micrometer 487 gauge radius set 488 vernier height gauge 489 plain ring and plug gauge 490 screw thread micrometer interchangeable 491 morse taper plug & ring gauge ( no. 0 to 7 mt quality material like tungsten based oil hardened & non shrinking steel ) 492 sin bar with centers 493 slip gauge metric set 494 boring tool holder 495 oil can 496 dog carrier 497 angle plate 498 spirit level 499 combination drill / centre drill ( a3, a4 & a5 ) 500 oil stone 501 tap wrench ( adjustable ) 502 tool bit assorted sizes on holder 503 spare grinding wheel ajax type for carbide tool 504 angle gauge for tool grinding 505 hand chaser 506 hand chaser 507 tool cemented carbide assorted shaped ( external ) for steel turning 508 thread plug gauge ( m 20 & m 21 ) 509 thread ring gauge 510 machine chaser ( m 12 to m 21 ( std. series ) to suit on ) 511 gauge drill grinding 512 magnetic chuck ( 150 mm dia.circular type ) 513 lathe mandrels ( diff. types ) 514 conventry type die head ( self opening ) 515 collapsible tap with attachment 516 bore dial gauge stems 517 tool holders 518 digimatic electronic vernier caliper 519 digimatic electronic outside micrometer...
35543092 supply of aluminium profilealuminium profile, aluminium profile length 2290 mm as per drg. no. t 4 4 004, alt c / 2, bright anodised conforming to specn. is:1868 1996 ( reaffirmed 2006 ) grade ac10. [ warranty period: 30 months after the date of delivery ] => limited...
34847273 supply of aluminium profile l=5000 mm, aluminium profile l=5000 mm, , aluminium profile l=5000 mm, as per drawing: lw44173 alt a => limited...
34795595 supply of aluminium profilealuminium profile, aluminium profile l=2350 mm, as per drawing: la10129 alt nil => limited...
34693368 supply of aluminium profile 3 types.aluminium profile 3 types., aluminium profile l=5000 mm, as per drawing: lw44173 alt a , aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil , al profile, as per drawing: un43104 alt a, quality plan: n.a. => limited...
34535943 supply of aluminium profile 2 typesaluminium profile 2 types, al profile, as per drawing: un43104 alt a, quality plan: n.a. , al.profile, as per drawing: un43103 alt a, quality plan: n.a. => limited...
34291584 supply of aluminium profile 3 types.aluminium profile 3 types., aluminium profile l=5000 mm, as per drawing: lw44173 alt a , aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil , al profile, as per drawing: un43104 alt a, quality plan: n.a. => limited...
34271554 supply of aluminium profile 2 typesaluminium profile 2 types, al profile, as per drawing: un43104 alt a, quality plan: n.a. , al.profile, as per drawing: un43103 alt a, quality plan: n.a. => limited...
33974416 supply of aluminium profilealuminium profile, aluminium profile l=2350 mm, as per drawing: la10131 alt a => limited...
33435068 supply of aluminium profile two types.aluminium profile two types.,aluminium profile l=2350 mm, as per drawing: la10129 alt nil , al profile, as per drawing: un43104 alt a, quality plan: n.a. => limited...
33298922 supply of aluminium profile (l=5000 mm).aluminium profile (l=5000 mm).,aluminium profile (l=5000 mm). => limited...
32724065 supply of aluminium profilealuminium profile,aluminium profile l=5000 mm, as per drawing: lw44173 alt a...
32578742 supply of aluminum profilealuminum profile,aluminium profile l=2350 mm, as per drawing: la10131 alt a...
32427652 supply of aluminium profilealuminium profile,aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil...
32213291 supply of aluminium profile for middle ceiling sheet.aluminium profile for middle ceiling sheet.,aluminium profile for middle ceiling sheet, as per drawing: le44110 alt nil...
30893063 s&i front lit of blue wave of canopy fascia at ros of zone 1 of sangrur territoryadditional rvi element – front lit of blue wave of canopy fascia at ros of zone 1 of sangrur territory: we are inviting competitive quotations to put up additional rvi element consisting of front lit of blue wave of canopy fascia at retail outlets of sangrur retail territory.brief of jobs to be done as below supply and installation of an additional blue acm ( bpcl approved make ) at an offset of 160mm over the 13w led linear profile light with top cover of pc diffuser, constant current existing blue fascia wave. the additional blue acm fascia is rectangular in shape of 125 mm depth measured from the top of the existing fascia in the groove formed between 125mm depth and 160mm offset of the blue fascia, the led tube lights of white color of 13 watts with a viewing angle of 120 degrees. the front lit light for blue wave should be of 1 meter long led linear light with aluminum profile and driver fitted on the outer edge of the pelmet touching the front and upper sides. the led strips are to be placed in the profile at 45 degree angle from horizontal ( or vertical ) to lighten towards the canopy fascia.the led driver should be bis approved fully potted ip67 led driver ( non integral, single driver to be used for 2 linear fixtures ) . the approved led chip make are cree / nichia / osram / samsung / citizen / philips ( lumileds ) / seoul / bridgelux.the other specification to be followed as given by bpcl. drawing and detailed technical specifications of jobs to be carried out are enclosed as annexure tech specs rvi add elements. the contractors will be required to supply and install front lit of blue wave of canopy fascia at existing retail outlets of bharat petroleum corp limited in ros under zone 1 of sangrur retail territory for any further clarifications, you may contact mr. pankaj gupta, asst manager, engg. retail on mail id / mobile no. pankajgupta@bharatpetroleum.in / 8502885181. all jobs will be carried out as per drawing approved by bpcl. the corporation does not give any guarantee for minimum amount of the job to be awarded to you. as per the prevailing site conditions / other conditions including local approvals, statutory requirements etc, job will be executed. it is to be noted that conditional tender will not be accepted and the corporation reserves the right to accept / reject the quote without assigning any reasons to the contractor. we are enclosing general conditions of contract ( gcc ) and cc also for your reference. e tenders in being floated in 2 zones for sangrur retail territory. e tenders for zone 1 will be evaluated and opened first and subsequently e tender for zone 2 will be opened. quote of the l1 vendor selected in zone 1 not be evaluated for zone 2 of sangrur retail territory the rates quoted shall be exclusive of goods & services tax. gst shall be paid separately, as applicable. please submit your competitive quotes latest before 14.02.2022 at 0900 hrs in the https: / / bpcleproc.in portal. bpcl will not be responsible for any delay in submitting e tender due to connectivity issues or any other technical issue at your end. =>limited...
30893059 s&i of front lit of blue wave of canopy fascia at ros of zone 2 of sangrur territoryadditional rvi element – front lit of blue wave of canopy fascia at ros of zone 2 of sangrur territory: we are inviting competitive quotations to put up additional rvi element consisting of front lit of blue wave of canopy fascia at retail outlets of sangrur retail territory. brief of jobs to be done as below supply and installation of an additional blue acm ( bpcl approved make ) at an offset of 160mm over the 13w led linear profile light with top cover of pc diffuser, constant current existing blue fascia wave. the additional blue acm fascia is rectangular in shape of 125 mm depth measured from the top of the existing fascia in the groove formed between 125mm depth and 160mm offset of the blue fascia, the led tube lights of white color of 13 watts with a viewing angle of 120 degrees. the front lit light for blue wave should be of 1 meter long led linear light with aluminum profile and driver fitted on the outer edge of the pelmet touching the front and upper sides. the led strips are to be placed in the profile at 45 degree angle from horizontal ( or vertical ) to lighten towards the canopy fascia.the led driver should be bis approved fully potted ip67 led driver ( non integral, single driver to be used for 2 linear fixtures ) . the approved led chip make are cree / nichia / osram / samsung / citizen / philips ( lumileds ) / seoul / bridgelux.the other specification to be followed as given by bpcl. drawing and detailed technical specifications of jobs to be carried out are enclosed as annexure tech specs rvi add elements. the contractors will be required to supply and install front lit of blue wave of canopy fascia at existing retail outlets of bharat petroleum corp limited in ros under zone 2 of sangrur retail territory for any further clarifications, you may contact mr. pankaj gupta, asst manager, engg. retail on mail id / mobile no. pankajgupta@bharatpetroleum.in / 8502885181. all jobs will be carried out as per drawing approved by bpcl. the corporation does not give any guarantee for minimum amount of the job to be awarded to you. as per the prevailing site conditions / other conditions including local approvals, statutory requirements etc, job will be executed. it is to be noted that conditional tender will not be accepted and the corporation reserves the right to accept / reject the quote without assigning any reasons to the contractor. we are enclosing general conditions of contract ( gcc ) and cc also for your reference. e tenders in being floated in 2 zones for sangrur retail territory. e tenders for zone 1 will be evaluated and opened first and subsequently e tender for zone 2 will be opened. quote of the l1 vendor selected in zone 1 not be evaluated for zone 2 of sangrur retail territory the rates quoted shall be exclusive of goods & services tax. gst shall be paid separately, as applicable. please submit your competitive quotes latest before 14.02.2022 at 0900 hrs in the https: / / bpcleproc.in portal. bpcl will not be responsible for any delay in submitting e tender due to connectivity issues or any other technical issue at your end. =>limited...
30009033 supply of aluminium profile length 2290mm.aluminium profile length 2290mm.,aluminium profile length 2290 mm as per drg. no. t 4 4 004, alt c/2, brightanodised conforming to specn. is:1868 1996(reaffirmed 2006) grade ac10. => limited...
29368595 supply of aluminium profile (02 types)aluminium profile (02 types),al.profile, as per drawing: un43103 alt a, quality plan: n.a. , aluminium profile l=5000 mm, as per drawing: lw44173 alt a...
29368555 supply of aluminium profile (02 types)aluminium profile (02 types),aluminium profile l=2350 mm, as per drawing: la10131 alt a , al profile, as per drawing: un43102 alt a, quality plan: n.a....