Water Supply And Sanitation Department - Punjab

40850038 tender for annual maintenance water supply scheme phase 1 & 2 water works kajauli. providing and fixing of skf make ball bearing no. 6313, c 3 for 10 mgd pump set and replacing wml bush set, including the cost of labour, alignment of pump and greasing etc. complete fitting and testing in a specified time at w/w phase 1 & 2 kajauli....

Indian Army - Punjab

40809378 bids are invited for purchase of training items white board with stand 4 feet x 3 feet , transparent flexible plastic pipe 3 inch , fire ball , screw jack , slide screw set , ball bearing , chain for chain saw machine , thread bearing , belt a 46 , wall mounted digital thermometrer hydrometer and humidity , iron pipe 2 inch , iron angle 2 inch total quantity : 351...

Indian Army - Punjab

40805354 bids are invited for repair maintenance of veh ba no 11c09101w tata mobile taking out self starter assembly , carbon bush , solenoid switch , armature rewinding , dismantling clutch assembly and replacement of the following parts items incl refixing the same , clutch pressure plate assembly complete , clutch release bearing , clutch cylinder lower , clutch cylinder upper , dismantling and taking out unserviceable spare parts items , fuel filter element make mico , oil filter make mico , clutch wire , air filter element make mico , coolant , fuel tank cleaning with washing material , break oil , computerized balancing and alignment of the wheels complete with setting back kamani, replacement of rubber bush and nipple greasing complete. , water servicing of the veh , denting painting of vehicle side front body , opening and taking down all wheels hub , wheel brake cylinder , wheel brake disc pad front left and right , disc rotor front left and right , ball bearing , repair to the alternator and replace the defective part i.e cut out switch, seal, rotor, rectifier plate, bearing etc and reassemble , disconnection of complete radiator assy, cleaning and descaling of chocked tubes of radiator, cleaning the fins of the radiator with acid water including brazing of worn out copper etc , suspension assembly with replacing , suspension bush , suspension rubber kit total quantity : 48...

Indian Army - Punjab

40789142 bids are invited for lv6 mt14 / 10518898 / 2610 001594 / tyre pneu 355 / 90x20 18pr sch lv6 mt6 / 10304125 / 2050 2012 5803 / rubber hose ( heat exchanger to connector lv7 / stln ( vf ) / 10332233 / x 2206000 / exhuast brake switch lv7 / tata / 10474150 / 2640 4620 3105 / ball bearing lv7 / stln / 10566829 / x3000650 / mud flap total quantity : 304...

Border Roads Organisation - Punjab

40772835 supply of spares for apollo paver finisher ap550 dx , supply of spares for apollo paver finisher ap550 dx , oil seal pt no.50 72 10 , solid rubber tire (22x16x5) pt no.a55480aa , relay rod end lh pt no.m10460aa , relay rod end rh pt no.m10450aa , sprocket pt no.d00001bb , sprocket pt no.d20230aa , hp hose 1/4x500lg 90 bend pt no.p40050aa , ball bearing pt no.6208zz , hp hose pipe pt no.p49125aa , hopper cylinder pt no.h40160aa , grade control cyl pt no.h40140aa , steering cyl pt no.h40120aa , screed cyl pt no.h40180aa , pedestal pt no.b20117aa , lh fork pt no.m15316aa , rh fork pt no.m15315aa , pedestal pt no.b20312aa , segment screw (lh) pt no.m15380aa , hex bolt (m12x120) pt no.n12120aa , hex nut 12m pt no.n55160aa , segment screw (rh) pt no.m15370aa , hp hose pt no.p49050aa , rubber foundation pad pt no.a75995aa , nipple pt no.f40190aa , hp hose pt no.p27251aa , hydraulic oil filter/retrurn filter pt no.h50110aa , hydraulic oil filter (travel drive) pt no.h50120aa , pressure filter (grade control) pt no.h50130aa , strainer pt no.h50220aa , diffuser pt no.h50201aa , king pin rep kit std_257633200120...

Indian Army - Punjab

40701582 bids are invited for isolator switch , solenoid valve , brake shoe assy , frt wheel brg kit , traficator assy rear , traficator assy frt , oil filter , disc pad , intake air hose , clock spring assy , dg ball bearing , coolant pipe hose total quantity : 22...

Department Of Heavy Industry - Punjab

40682103 bids are invited for ball bearing 6204 material code 551110620400 ( q3 ) , ball bearing 6205 2rs material code 551190620500 ( q3 ) , ball bearing 0132 material code 552115111400 ( q3 ) total quantity : 1100...

Punjab Gramin Bank - Punjab

40663431 tender for items clerical/officer table 5 nos p&f clerical/ officer counter 4 6x 2 6 x 2 6 ht. with counter shall have wooden partition 4 0x4 0 with & all arou duly polished on one side of counter. counter shall be made of mm thick commercial board of duro/century/ kit ply. it shall finished with 1 mm thick laminate of cedar white color on sides of counter. the rates also include drawer with hettich ba bearing slides, cabinet box etc. counters are to be provided wi computer keyboard tray of ebco make codè no kbt 45 and draw and boxes also making position for electrical points conduits switch boxes with plastic round shape 2 diameter openings etc al fitting of u.p.s shelf, foot rest of 3 x 1.5 in c.p. teak wood the bottom. i.e. complete job in all respects with fitting a accessories like godrej locks. handles, hinges etc. lower portion wide shall be in burgundy color laminate (bank shade) on front a side. edges of the counter shall have teak wood molding du polished. edges shall be covered with teak wood molding/marg duly burgundy color (bank color) polished. cashier table providing and fixing of cashier counter 5 06 x 2 6 wide. 3 9 high shall be made of 19 mm. thick commercial board of dur century/kit ply and finished with imm. cedar white col laminate on all vertical & exposed and visible surfaces of count counters are to be provided with computer keyboard tray of eb make code no kbt 45 and drawers with hettich ball bearing slid for drawer slides with partition for keeping currency and box also marking position for electrical points conduits & switch box with plastic round shape 2 diameter openings etc also fitting u.p.s. shelf at bottom, i.e. complete job in all respects with fittin and accessories like godrej /latch locks, handles, hinges et lower portion 4 wide shall be in burgundy color laminate (ba shade) on front and side. edges of the counter shall have teak wo molding duly polished manager table 6 0 x 2 6 with side rack 36 x 16 x 20 mananer table 6 0 x 2 6 x 2 6 with side rack of size v 6 x 16 26 high. it shall be made of 19 mm thick anti termite mercial hard bishop board. top and vertical exposed surfaces chill have team thick wirte cedar aminale matching with existing table all exposed edges shall haveteur mount holding duly polished. lower portionwide shall be in burgundy color laminae (bank stade) on front and side. the rate ulso inetales fitting of lockable keybounds locks in drawers with hettich ball bearing slides, terminals & cp shelf, foot rest of size 3x 1.5. the non sun miles area should be daily painted or polished after making the smooth ground with second quality paint and chilk mitti complete jobs incall respects manager table top glass 6 0 x 2 6 x 12 mm with grinding of edges & corners....

Indian Army - Punjab

40621748 bids are invited for lv6 mt14 / 10518898 / 2610 001594 / tyre pneu 355 / 90x20 18pr sch lv6 mt6 / 10304125 / 2050 2012 5803 / rubber hose ( heat exchanger to connector lv7 / stln ( vf ) / 10332233 / x 2206000 / exhuast brake switch lv7 / tata / 10474150 / 2640 4620 3105 / ball bearing lv7 / stln / 10566829 / x3000650 / mud flap total quantity : 304...

Northern Railway - Punjab

40521360 supply of double row self aligend ball bearingdouble row self aligend ball bearing,double row self aligend ball bearing size: 50x110x40 mm width drg no skf 2310 c3 or equivalent fag cage steel.,fag no. 2310 c3cage steel [ warranty period: 30 months after the date of delivery ]...

Water Supply And Sanitation Department - Punjab

40496889 tender for providing and fixing of skf make ball bearing no. 6313, including the cost of labour, alignment of pump and greasing etc. complete fitting and testing in a specified time at w/w phase 1 & 2 kajauli....

Border Roads Organisation - Punjab

40385877 supply of spares for escorts mini tvrr ed 30 , supply of spares for escorts mini tvrr ed 30 , pre cleanerv19140110 , pressure switchpp11677 , hing541971 , bow plate assy48 f2 003e , bow plate assy48 f2 004d , driver plate43f2008 , stop cable14 b 4 045 , throttle cable43 c 3 017a , flexible pipe48f3003d , oil level gauge922552 , air cleaner assy06.761.200 , hose leak return43 c 3 015a , hose supply4.11.07.0 , fuel tank cap48 b 1 001 , grooved ball bearing pp11447 , polyurethan scrapo48 c 2 040 , hose00107441 , screw socket00260894 , elbow00225665a , element hyd filterhfe 10 025 , sprinkle nozzle00394297 , king pin rep kit std_257633200120...

Border Roads Organisation - Punjab

40353475 supply of spares for escorts tvrr hd 85 , supply of spares forescorts tvrr hd 85 , stop cable c7401928 , actuating cablec836778087a0 , tank cap8510361 / 36c2003 , rubber metal bufferc83624948300 , radial road end brgc83637240400 , scrapperc83646008700 , scrapper support platec836c201200 , axial face seal ( ducone seal ) c84238326008 , grooved ball bearing 16030 din 625c83628824100 , twin nipple330507a0 , twin nipplec836330493c0 , o ringcc83657647600 , sprinkler nozzle394297 , screwed socketc83626089400 , tank capc83621124900 , hose 5.5 mtrc83610744100 , hose clampc85622578900 , oil level gaugec8d922552000 , hosec8hn45163050 , king pin rep kit std_257633200120...

Indian Army - Punjab

40320432 bids are invited for mt spares chain and sprocket kit , brake shoe assy , gasket set complete engine , bush chain tensioner pad , valve stem seal , slector and shofter shaft , ball bearing , pipe assy total quantity : 8...

Military Engineer Services - Punjab

40256556 tender for improvement to certain omqs and smqs at af station bhisiana; 2 taking down cement or cement lime plaster of any descriptionand any thickness on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 3 material and labour for rendering 15 mm thick cement plaster in cm ( 1:4 ) on fair faces of brick or concrete surfaces and finishing the surface even and fair ( without using extra cement ) etc, complete all as specified and directed. 4 material and labour for rendering 12 mm thick cement plaster in cm ( 1:6 ) on fair faces of brick or concrete surfaces and finishing the surface even and fair ( without using extra cement ) etc, complete all as specified and directed. 5 material and labour for rendering 5 mm thick cement plaster in cm ( 1:3 ) finished even and fair ( without using extra cement ) on fair faces ofconcrete surfaces in ceiling , complete all as specified and directed. 6 material and labour for rough cast plaster on brick walls consisting under coat of cement and sand mortar 1:4 not less than 10mm thick and while it is still in plastic state the rough cast mixture consisting of graded stone or fine gravel mixed with coarse sand and cement in the ratio 1:1:1 shall be applied and finish even, complete all as specified and as directed. 7 material and labour forpreparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of cement base primer on new plastered surfaces, complete all as specified anddirected by engineer in charge. 8 material and labour for preparation of new plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces, complete all as specified anddirected by engineer in charge. 9 material and labour for complete removal of existing treatmentand preparation of old plastered / unplastered surfaces of walls andapplying two coats of cement base paintover a coat of cement base primer onwall surfaces complete all as specified anddirected by engineer in charge. 10 material and labour for complete removal of existing treatment and preparation of old plastered / unplastered surfaces of walls / parapats andapplying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces, complete all as specified and as directed. 11 material and labour for prepration of new plastered surfaces of ceiling and applying three coats of white wash on ceiling , complete all as specified and directed. 12 material and labour for prepration of old plastered surfaces of ceiling and applying two coats of white wash on ceiling, complete all as specified and as directed. 13 material and labour for prepration of new plastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed. 14 material and labour for prepration of old plastered surfaces of walls and applying two coats of white wash, complete all as specified and as directed. 15 material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper acrylic / distemper oil emulsion acrylic, white or tinted over a coat ofprimer of same make, complete all as specified and as directed. 16 material and labour for complete removal of existing treatment andpreparation of old plastered surfaces of walls and applying two coats of oil bound distemper acrylic / distemper oil emulsion acrylic , white or tinted over a priming coat of same make on wall surfaces, complete all as specified and as directed. 17 material and labour applying 1 2 mm thick wall care putty ( jk / birla / berger ) on walls, including making surface even and smooth using sand paper before applying priming coat, complete all as specified and as directed. 18 demolition of reinforced cement concrete of any description and in any position, cut as required to facilitate demolition, complete all as specified and as directed. 19 demolition of reinforced cement concrete of any description and in any position ( other than ground floor ) in beams, staircases, landing chajjas and similar work, complete all as specified and as directed. 20 material and labour for reinforced cement concrete type b 1, ( 1:2:4 ) 20mm graded aggregate as in roofs, floors, kitchen platform, beams, lintels, columns, shelves, staircase, landing, parapets and railings and with similar suspanded works including necessary form work required at site and applying a coat of cement slurry over old surfaces of concrete to make perfect binding, complete all as specified and directed at site, complete all as specified and as directed. 21 all as per srl item no 20 above but as in chhajjas, complete all as specified and as directed. 22 formwork to chullah hoods, shelves, chajjas, troughs and similar items in flats including edges, complete all as specified and as directed. 23 formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 10 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide for rough finished concrete surface, complete all as specified and as directed. 24 material and labour for mild steel tmtbars 8 to 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel ( annealed ) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. 25 all as per srl iten no 23 above but 6 to 8 mm dia, complete all as specified and as directed. 26 supply and fix chicken wire mesh / hard drawn wire fabric of weight not exc 4 kg per sqm, cut to lengths, bent to shape required and tying with and including mild steel wire ( annealed ) not less than 0.9 mm dia, complete all as specified and directed. 27 demolition of cement concrete unreinforcedof any description in any position not exceeding 150 mm thick ( below or above ground level ) , complete all as specified and as directed by engineer in charge. 28 material and labour for 75 mm thick pcc ( 1:3:6 ) type c 2 using 40mm graded stone aggregate as in plinth protectionfinishing cement concrete surface even and fair without using extra cement, including making construction joint at a interval not exceeding 3.00 m and at each corner and filled with sealing compound with grade a ( normal ) in 25 / 30, complete all as specified and as directed. 29 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises, complete all as specifed and directed. 30 material and labour for 25 mm thick cement concrete type b1 ( 1:2:4 ) ( 20 mm graded stone aggregate ) , as in sub base of floor , complete all as specified and directed. 31 material and labour for non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. including 15mm thick screed bed in cm ( 1:4 ) set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed. 32 material and labour for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cm ( 1:6 ) for laying floor finishes, complete all as specified and as directed. 33 material and labour for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in cm 1:4 to receive vertical tiles, complete all as specified and as directed. 34 material and labour for vetrified tiles 9 to 10 mm thick light shade ( square / rectangular ) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cm ( 1:4 ) for laying floor finishes, complete all as specified and as directed. 35 material and labour for vetrified tiles 9 to 10 mm thick light shade ( square / rectangular ) on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in cm 1:4 to receive vertical tiles, complete all as specified and as directed. 36 material and labour for glazed ceramic coloured tiles in vertical surface 350x250x7 mm / 450x350x7mm thick including 10mm thick cement plaster in cm 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and as directed. 37 demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar, complete all as specified and directed. 38 material and labour for granite ( of any type ) worktable rubbed and polished 18 20 mm thick machine cut, in steps, jams, pillars, window cills, cooking platforms and like laid and bedded over 15 mm thick cement mortar in cm ( 1:6 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to macth with shade of granite , complete all as specified and directed. 39 material and labour for 12 15mm thick green marble slab flooring including 15mm thick screed bed in cm ( 1:4 ) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab one side bullnosed etc, complete all as specified and as directed.note : cost of screed bed will deem to be included in the quoted unit rate. 40 material and labour for 12 15mm thick green marble in riser of steps , skirting, dado and pillar laid over cement screed and cement slurry including 10mm thick cement plaster 1:3 cm to receive kota stone and jointedrubbing and polishing completeall as specified and directed.note : cost of cement plaster deem to be included in the quoted unit rate. 41 rounding the edge of stone slabs one edge such as in steps, cooking platforms, and the other simmilar situation, complete all as specified and as directed. 42 material and labour for machine cut kota stone slab flooring 20 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 15mm thick screed bed of cm1:4 including rubbing and polishing, complete all as specified and as directed. 43 material and labour machine cut kota stone slab20 25mm thick in riser of steps , skirting, dado and pillar laid over cement screed and cement slurry including 10mm thick cement plaster 1:3 cm to receive kota stone and jointedrubbing and polishing, complete all as specified and as directed. 44 demolition of cement concrete ( unreinforced ) exc 15 cm thickness but above ground floor, sunkan floor, complete all as specified and as directed. 45 material and labour for 15 mm thick rendering in cement mortar ( 1:3 ) as in sunken portion walls and floor, mixed with water proofing compound 3%by weightof cement, finishing surfaces even & smooth without using extra cement complete all as specified and as directed. note : water proofing compound shall be measured and paid under appropriate item of this sch ‘a’. 46 supplying only integral water proofing compoung, mixed as per instruction given over it as per manufactures direction, complete all as specified and as directed. 47 material and labour for bitumen hot blown any grade, applied hot, intwo coats to concrete surfaces at the rate of 1.5 kg per sqm per coat, including cleaning of surfaces, complete all as specified and as directed. 48 material and labour for laying 50 micron polythelene film, black in floors of sunkan, complete all as specified and as directed. 49 material and labour for pcc ( 1:5:10 ) type e 2 using 40mm graded stone aggregate as in fillingof sunken floorand mass concrete, complete all as specified and as directed. 50 material and labour for 50 mm diagi spought pipefixed in sunken floors by means of cutting holes in wall / taaking down old u / s pipe, fixed andbeded in cement mortor / pcc ( 1:2:4 ) and making good the disturbed portion of wall, complete all as specified and as directed. 51 dismentling cast iron or reinforced concrete pipes , floor / walls up to 100 mm bore jointed in cement mortar and taking out, complete all as specified and as directed. 52 supply and fixed 100 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, laid in trenches, complete all as specified and as directed. 53 supply and fixed75 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, laid in trenches, complete all as specified and as directed. 54 supply and fixed 100 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, fixed to walls, complete all as specified and as directed. 55 supply and fixed 75mm bore cast iron soil waste and vent pipes , sand cast pipe, in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed. 56 supply and fixed in repair cast iron p or ;s; trap 100 mm bore, complete all as specified and as directed. 57 supply and fixed in repair cast iron socket ( double collar ) , 100 mm bore, complete all as specified and as directed. 58 supply and fixed in repair cast iron socket, 75 mm bore, complete all as specified and as directed. 59 s&f in repair cast iron 100 mm bore branch piece single, ( equal or unequal ) singlewith acces door, ordinary or inverted ( spigot or socket type ) or with parrallel branches, with oval access door, complete all as specified and as directed. 60 supply and fixed in repair cast iron bends, 100mm bore , ( any radius ) , disiminishing pieces or tapper ( larger bore measured ) with oval asses door, complete all as specified and as directed. 61 supply and fixed in repair cast iron bends, 75 mm bore , ( any radius ) , disiminishing pieces or tapper ( larger bore measured ) with oval asses door, complete all as specified and as directed. 62 supply and fixed in repair cast iron 75 mm bore branch piece single, ( equal or unequal ) singlewith acces door, ordinary or inverted ( spigot or socket type ) or with parrallel branches, with oval access doors, complete all as specified and as directed. 63 supply and fixed in repair for 75mm cast iron floor trapwith ss grating 100 to 125 mm dia , including jointing with solvent cement , joint to waste pipe fixed in cement concrete type b1 ( 1:2:4 ) , complete all as specified and as directed. 64 supply and fixed in repair stack clamp for 75 mm bore pipe out of 50 mm by 5 mm flat iron and 16 round round iron stay.including bolt and nuts and securing ends of stay to walls or roof, complete all as specified and as directed. 65 supply and fixed in repair stack clamp for 100 mm bore pipe out of 50 mm by 5 mm flat iron and 16 round round iron stay.including bolt and nuts and securing ends of stay to walls or roof, complete all as specified and as directed. 66 material and labour for providing precast cement concrete cover slabs using cement concrete type b1 ( 1:2:4 ) , 20 mm graded aggregate, ( for manholes etc ) and simillar works, complete all as specified and as directed. 67 taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and as directed. 68 material and labour 15 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. 69 fixing only 15 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and as directed. 70 taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and as directed. 71 material and labour 20 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. 72 fixing only 20 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and as directed. 73 taking up or down 25 mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and as directed. 74 material and labour 25 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. 75 fixing only 25 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and as directed. 76 cutting chases, pining in making good to facing where required and pointing incement mortar 1:3 for concealed water tubing , cutting not exc 10 cm girth , complete all as specified and diredcted. 77 dismantling pvcwater tanksexc 250 ltr and n exc 500 ltr and removing to store, complete all as specified and as directed. 78 material and labour, for three layered white colourrotational moulded polyethylene water storage tanks of 500 ltrcapacity ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i, complete all as specified and as directed. 79 dismantling pvcwater tanksexc 500 ltr and n exc 1000 ltr and removing to store, complete all as specified and as directed. 80 material and labour, for three layered white colourrotational moulded polyethylene water storage tanks of 1000 ltrcapacity ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i, complete all as specified and as directed. 81 material and labour, 20mm ballvalves, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed as in repairs, complete all as specified and as directed. 82 material and labour for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed screwed both ends for iron pipes or for union and fixed in repairto 20mm dia of pipe, complete all as specified and as directed. 83 material and labour gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed screwed both ends for iron pipes or for union and fixed in repair to 15 mm dia of pipe, complete all as specified and as directed. 84 material and labour vitreous china squatting pan , orissa pattern, size 580 x 440 mm white , with integral foot rests complete including provision of lime concrete bedding fixed as in repairs, complete all as specified and as directed. 85 supply and fix in repair china wash down water closet padestal pattern white excluding flush and fix to position, including seat cover and connection to drain etc, complete all as specified and as directed. 86 supply and fix health faucet fixing in pipe etc, complete all as specified and as directed. 87 supply and fix toilet paper holder of stainless steel fixed to walls, complete all as specified and as directed. 88 supply and fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass corner shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed. 89 material and labour pvc valveless , syphonic action type , flushing cistern, low level , white, with inlet, ball valve, float and handle, completewith flush pipe of polythelene of low or high density or pvc 32 mm dia , including brackets / fastening assesoriesof 10 litres capacity , fixed in repair, complete all as specified and as directed. 90 supply and fix in repair for mirror cabinet ofmin size 430x330 mm with openable door shutteras approved by ge, complete all as specified and as directed. 91 material and labour vitreous china wash basin, white , flat back, size 550x400mm fixed onbrackets or stands, including 32 mm waste coupling of ptmt ( half or full threaded ) / cp brass and corrugated waste pipe with adopter of 900 mm long, fixed in repair, complete all as specified and as directed. 92 supply and fixed in repair wash hand basinbrass cp mixture 15mm bore for mixing hot and cold water screwed down for 15 mm iron pipe and fixed, complete all as specified and as directed. 93 supply and fixed in repair 15 mm dia bore cp angular stop cock with wall flange cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union completeall as specified and as directed by engineer in charge. 94 supply and fixed in repair15 mm dia bore cp concealed stop cockcast copper alloy chromium plated with long sahnk , fancy type, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union, complete all as specified and as directed. 95 supply and fixed in repair pvc connections 15 mm size with ptmt nuts of length 450mm, complete all as specified and as directed. 96 supply and fixed in repair pvc connections 15 mm size with ptmt nuts of length 600 mm, complete all as specified and as directed. 97 supply and fixed in repair, 15 mm diabib taps , fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed. 98 supply and fixed in repair, brass cp wall mixer, 15 mm bore, for mixing hot and cold water , screwed down for iron pipe and fixed, complete all as specified and as directed. 99 supply and fixed in repair, wall mounted goose neck sink mixer ( hot and cold ) with provision of swivel arm , connecting legs and wall flanges, complete all as specified and as directed. 100 supply and fix 15mm dia pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and flu nuts screwed for iron pipe as fixed in repairs, complete all as specified and as directed. 101 supply and fixed in repair, brass chromium plated shower rose 125 mm size with or without swivel joints, including fixing to steel pipe or union, complete all as specified and as directed. 102 supply and fixed in repair, stainless steel soap dish, complete all as specified and as directed. 103 supply and fixed in repair, brass cp tubular towel rail of 20 mm dia, d type , 60 cm long between flange , fixed in repair, complete all as specified and as directed. 104 supply and fixing stainless steel towel ring round / square with cap , with fixing screws, complete all as specified and as directed. 105 supply and fixed in repair, sinks made of stainless steel 1mm thick kitchen or labo ratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm , including 40 mm bore dia cp waste coupling ( half / full threaded with 900 mm and pvc waste pipe min 900 mm long, complete all as specified and as directed. 106 supply and fixing in repair kitchen plate rack withof size 750x900 x 250mm of stainless steel, complete all as specified and as directed. 107 supply and fixing in repair kitchen plate rack withof size 750x600 x 250mm of stainless steel, complete all as specified and as directed. 108 suply and fixing coat hooks of six pegs made out of stainless steel 45 cm long ( as per sample ) , complete all as specified and as directed. 109 dismentling of boarding in any position and in any description fixed with nail, complete all as specified and as directed. 110 supply & fixing of 18 mm thick pvc ply of plain color fixed with screws, solvent cement / adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets, complete all as specified and as directed. 111 supply & fixing of 18 mm thick pvc ply of one side prelam / rigidlam and other side balancing laminate colour to make kitchen cabinet shutter / drawer front shutters, complete all as specified and as directed. 112 supply & fixing of 5 mm thick pvc ply of plain white colour fixed with screws, solvent cement / adhesive to make kitchen cabinet back covering and pull out drawer base complete as per specifications and as directed by the engineer in charge. 113 supply & fixing for 20mm wide & 1mm thick pvc edge bedding of pvc pested on edges with suitable adhesive, complete all as specified and directed 114 supply & fixing of auto closing hinges openable at 0 degree for kitchen cabinet shutters, complete all as specified and as directed. 115 supply & fixing of ball bearing runners 45 mm telescopic channel ( 20 inch ) full extension load capacity 50 kgs, complete all as specified and as directed. 116 supply & fixing of stainless steel handles 100 mm size for kitchen cabinet shutters, complete all as specified and as directed. 117 supply & fixing of chrome plated stainless steel wire basket ( storage basket ) pull out type for large utensils, size 486 x 500 mm with necessary fixing clips etc., complete all as specified and as directed. 118 supply and fixing of chrome plated stainless steel wire basket ( cup and saucer basket ) pull out type, size 530 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 119 supply and fixing of chrome plated stainless steel wire basket ( jar basket ) pull out type, size 536 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 120 supply and fixing of chrome plated stainless steel wire basket ( thali basket ) pull out type, size 380 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 121 supply and fixing of chrome plated stainless steel wire basket ( cutlery basket ) pull out type, size 380 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. . 122 supply and fixing of chrome plated stainless steel wire basket ( grain trolley ) pull out type, size 380 x 500 mm with necessary sliding frame structure, fixing clips etc, complete all as specified and as directed. 123 supply & fixing of chrome plated stainless steel wire basket ( storage / plain basket ) pull out type, size 380 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 124 supply & fixing of chrome plated stainless steel wire basket ( bottle pull out ) pull out type, size 150 to 200 mm with necessary sliding frame structure, fixing clips etc, complete all as specified and as directed. 125 material and labour continous piano hingesstainless steel , bright finish width of flaps when open 40 mm, complete all as specified and as directed. 126 supply and fixing hasp and staple safety type aluminium powder coated with mild steel pin inculding bolt to hinge plate and fix with screws 150 mm size of hasps and staples, complete all as specified and as directed. 127 supply and fixing magnetic catcherfor cupboards complete as all specified and directed by engineer in charge, complete all as specified and as directed. 128 s&f in repair 20 mm dia stainless steel polished 204 grade drapery rod / curtain rod 1 to 2mm thick with finals decorative, including fixing of brackets and both ends decorative nobs, completeall as speccified and directed as per approved sample by engr in charge. 129 supply and fixed in repairms powder coated curtain rods 18 to20 mm boreover doors and windows , with fixing ms powder coated brackets, including screws, rawal plug , and pvc powder coated fineals / fency type end bulbs at each end of curtains rod, any colour etc, complete all as specified and as directed. 130 taking down chowkhats or frames / steel windows / ventilators, not exc 1.5 sqm each ( without taking off shutters from the frames ) , complete all as specified and as directed. 131 taking down shutter of area exc 1 sqm but n exc 2 sqm each, complete all as specified and as directed. 132 solid pvc door frame of size 50mm x 47mm made out of 5mm plain coloured pvc sheet reinforced with ms square tube, supplying & fixing in opening as per specification and drawing, complete all as specified and as directed. 133 factory made solid panel pvc door shutter 30mm thick ( stile ) , consisting of frame made out of ms tubes for top & bottom rails. ms frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drg. 134 supply and fix for 100 mm sizebutt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type b 21, complete all as specified and as directed. 135 supply and fix for 125 mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed. 136 supply and fix 100 mm aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and as directed. 137 supply and fix for anodised aluminium frame for doors, windows ventilators ( powder coated ) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by engineer in charge. 138 s&f powder coated anodised aluminium side hung / sliding type window and ventilator shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, locks, glazing clips, rubber packing, anodised aluminium snap beading, screws etc, complete all as specified and as directed. 139 material and labour for sheet glass ordinary quality 5.5mm thick and glazing with oil putty or fixed with bead / glazing pins in squares n.exc 0.5 sqm each pane all corner of glass to be fixed with silicon, complete all as specified and as directed. 140 supply and fixingstainless steelwire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tack or galvanised wire staple, complete all as specified and as directed. 141 supply and fix powder coated aluminium decorative grill of size of mesh 75mm fixed with doors, window for safety of glass etc. complete all as specified and as directed. 142 supply and fix steel window / ventilator of box section having 1.25 mm thick crc sheetframe with double shutterinside gauged shutter and outsideglazed shutterwith one nos steel handle in each shutter, one nospeg stay in each shutter , complete with glazing bars and 08 nos of 10 x 10 mm square guard bars in equal spacing, devoited or welded as per sample incl one coat of red oxide primer all as specified and directed. ( the rates includes 4 mm thick plain sheet glass and galvanized mild steelwire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and 2 coat of synthetic enamel paint over a coat of zinc chrome primer ) note : the design of window to be facilitated by cooler fixing provision where ever reqd ) , complete all as specified and as directed. 143 taking down chowkats & shutters without taking offshutters from the frame, size of openingexc. 1.50 sqm but not exc 4 sqmeach. complete all as specified and as directed. 144 supply and fix pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directedof size 125 x 60mm, complete all as specified and as directed. 145 supply and fix pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directedof size 105 x 60mm, complete all as specified and as directed. 146 material and labour for pcc ( 1:3:6 ) type c 1 using 20 mm graded agg as in back of pressed steel chowkhats etc, complete all as specified and as directed. 147 material and labour for pcc ( 1:2:4 ) type b2 using 20 mm graded agg as in hold fast of steel chowkhat / frames etc, complete all as specified and as directed. 148 supply and fix framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165, complete all as specified and as directed. 149 supply and fixing, factory made, 35mm thick plain framed panelled shutters ( two panel ) with lock rail and panelof 9mm bwp commercial ply or 12mm veneered particle board with commercial veneering on both faces using 2nd class hw as in rail and style. the size of rail and style as per is 1003 ( part – i ) , kiln seasoned and chemically pressure treated, complete all as specified and as directed. 150 supply and fixed 35mm thick glazed and skelton shutter iind class hard wood , open rebated and prepare to receive glass, gauge etc. ( without sash bars ) edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of member of shutters as specified in ssr part 1 , section 8 , clause 8.24 ( a ) , complete all as specified and as directed. 151 taking down shutter of any description exc 1.00 sqm but not exc 2.0 sqm each and refixing in same opening after easing and adjusting ( chowkat / frame changed ) etc, complete all as specified and as directed. 152 supply and fixed in repair 100 mm butt hinges medium weight, cold rolled mild steel, fixed in repair, complete all as specified and as directed. 153 supply and fixed 150 aluminium anodised barrel tower bolts of extruded section and fixed, complete all as specified and as directed. 154 supply and fixed 150 aluminium anodised barrel tower bolts of extruded section and fixed in repair tower bolt, complete all as specified and as directed. 155 supply and fixed 300 mm aluminium ally, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed , complete all as specified and as directed. 156 supply and fixed 300 mm aluminium ally, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed in repair, complete all as specified and as directed. 157 supply and fixed 150 mm extruded aluminium alloy handles, fabricated typeanodised, complete all as specified and as directed. 158 supply and fixed 150 mm extruded aluminium alloy handles, fabricated typeanodised, fixed in repair handles, complete all as specified and as directed. 159 supply and fixed floor door stopper of size 140 mmof aluminium ally body and tongue, anodised, with hard drawn steel spring ficed in floors, complete all as specified and directed. 160 supply and fixed mild steel300mm ordinary rat tail rod pattern springs, including roller and roller plate fixed in repairs complete 161 supply and fixed in repair of aluminium body door cill upto 1mtr length at bottom part of door to stop entry of insect inside the room complete all as specified and as directed. 162 supply and fixingin repairs galvanized mild steelwire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tack or galvanised wire staple complete. 163 material and labour for applying two coats of synthetic enamel paint over a coat of pink primer including prepration of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed. 164 material and labour for preparation of old wooden surface and applying two coat of synthetic enamel paint, complete all as specified and as directed. 165 supply and fixed joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. ( cut to ordinary lengthsi.e. within 20mm of the length indicated in fe 410 w ( gdee 250 ) quality a, complete all as specified and as directed. 166 material and labour for preparation of new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer exposed to view surfaces complete all as specified and as directed 167 material and labour for preparation of old steel surfaces of any description not otherwise described over 10cm width or grith and applying one coats of synthetic enamel paint overcomplete all as specified and as directed. 168 taking down existing cement plaster / roof treatment including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed. 169 brushing neat cement slurry with 3.0 kg of cement per sqm complete all as specified and as directed. 170 material and labour for providing cement concrete type bo ( 1:2:4 ) 12.5 mm graded stone aggregate for providing slope, maintain level , roof kerbs or mud stops rounded or chamfered edges, complete all as specified and as directed. 171 material and labour for 10 mm thick cement screed bed or beding layer / plaster in cement ( 1:4 ) mixed with water proofing compound on concrete roof surface, complete all as specified and directed. 172 material and labour app based polymeric membrane minimum wieghing 3kg / sqm and minimum 3 mm thick reinforced with polyster non wove fabric ( weight not less than 150 gms / sqm ) laid over a coat of hot bitumen 85 / 25@ 1.20 kg per sqm by torch application , including a coat of aluminium paint applied on mambrane, complete all as specified and as directed. 173 demolition of brickwork or stone / boulder masonary, built in cement mortar or cement lime mortar, complete all as specified and as directed. 174 demolition of old u / s rcc water tanks of capacity exc 250 litre but not exceeding 500 litre and removing from site, complete all as specified and as directed. 175 disconnecting existing water tank for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of tank exc 250 ltr and not exc 500 ltr capacity, setting aside ( or lowering if required ) for repairs, cleaning, etc. and hoisting if required reconnecting and re fixing in position, complete all as specified and as directed. 176 material and labour for brick work with subclass b bricks, straight or curved on plan exc 6 m mean radius , buit in cement mortar ( 1:6 ) , complete all as specified and directed. 177 material and labour for brick work with subclass b bricks, straight or curved on plan to anybradius in half brick thick wall, buit in cement mortar ( 1:4 ) , complete all as specified and directed. 178 internal electrification works 179 taking down carefully copper / aluminium point wiring including ( light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, batten holders, shades conical fan regulators, light or power sockets etc ) including taking down carefully by unscrewing from boards / outlet / dbs / fittings such as switches, sockets, lamp holders, brackets, ceiling fittings, bulkhead fittings, sketch fittings, tube light fittinfs, fan regulator electric metre box any type etc as directed by by engr in charge. all the removed material to be deposited in age e / m store yard or will be handed over to the contractor under schedule of credit and making good to disturbed surfaces by plastering and two cats of distamper, complete all as specified and as directed. note each item of fittings / fixtures are to be are to be considered as one unit. 180 supply and fix concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor pvc insulated and unsheathedcable 1100 volts grade drawn through and including non metallic rigid pvc conduit, medium grade minimum 19mm dia isi marked and conduit accessories fixed concealed in wall / ceiling / roof etc with sunken type pressed steel / welded ms terminal boxes made out of 1.6 mm ms sheet, 3mm thick laminated sheath top cover for mounting of fittings, switches, sockets outlets, regulators etc complete including provisining of 1.5 sqmm pvc insulatedunsheathedcable 1100 volt grade with multi stranded copper conductor to common earth and connected to earth dolly, complete all as specified and as directed. 181 one light / fan point controlled by one switch 6 amp one way, complete all as specified and directed. 182 one 3 pin switch socket combination 6 amp on the independent board, complete all as specified and directed. 183 one 3 pinswitch socket combination on same board with other switches, complete all as specified and directed. 184 one bell point controlled by one switch 6 amp one way, complete all as specified and directed. 185 one light point controlled by two 2 way switch, complete all as specified and directed. 186 all as described above but point wiring with 2.5 sqmm single core multi stranded copper conductor pvc insulated & unsheathedcable 1100 volt grade and 1.5 sqmm pvc insulated and unsheathed cable 1100 volt grade with multi stranded copper conductor for earth wire for 15 / 16 amp multi purpose socket combination point on independent board, complete all as specified and directed. 187 material and labour for modular switch 1 way 6 amp one module, complete all as specified and directed. 188 material and labour for modular switch 2 way 6 amp one module, complete all as specified and directed. 189 material and labour for modular bell push switch, 6 amp one module, complete all as specified and directed. 190 material and labour for modular socket 6 amp 2 / 3 pin combined 2 module, complete all as specified and directed. 191 material and labour for modular switch socket combination 16 amp, 6 pin, 3 module, complete all as specified and as directed. 192 material and labour for fan step regulator, 120 w 1 module, complete all as specified and directed. 193 supply and fix bell ding dong ac 230volts single pole, complete all as specified and directed. 194 supply and fix ceiling rose 65x17mm of three terminals pvc / polycarbonate, isolated body, complete all as specified and directed. 195 taking down, dismantling, cleaning, painting and of ceiling fan / ext fan for wiring work and refixing the same with pvc flexible wire 3 core with copper conductor 0.5 sqmm upto connector / ceiling rose, complete all as specified and directed. 196 supply and fix 1x18 watt 220v, 4 feet ac deorative box type with driver holder including led tube light connecting up with three core copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by engr in charge. 197 supply and fix 1x18 watt 220v, 2 feet ac deorative box type with driver holder including led tube light connecting up with three core copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by engr in charge. 198 supply and fixing led street light / security light 35 / 36 watt ip 65 complete with suitable size gi bracket and ms clamp to fix it on wall including connecting up with three core copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by engr in charge. 199 material and labour for submain wiring with 2 runs of copper conductor pvc insulated unsheathed cable 1100 volt grade 4 sqmm drawn through pvc conduit medium grade isi marked25mm dia as per is specification fixed concealedin wall / ceiling including conduit and conduit accessories and incl provn of pvc insulated 4 sqmm multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old and making good to the disturbed surface by plastering and two coat of distamper all as directed at site, complete all as specified and directed.note : two runs of 4 sqmm cable alongwith one run of 2 sqmm pvc insulated unsheathedcopper conductor as earth wire, conduitand conduit accessories will be measured as one length. 200 material and labour for submain wiring with 4 runs of copper conductor pvc insulated unsheathed cable 1100 volt grade 6 sqmm drawn through pvc conduit medium grade isi marked25mm dia as per is specification fixed concealedin wall / ceiling including conduit and conduit accessories and incl provn of pvc insulated 2 runs of 6 sqmm multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old and making good to the disturbed surface by plastering and two coat of distamper all as directed at site, complete all as specified and directed.note : two runs of 6 sqmm cable alongwith one run of 4 sqmm pvc insulated unsheathedcopper conductor as earth wire, conduitand conduit accessories will be measured as one length. 201 supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb of 20 amps capacity, complete all as specified and directed. 202 supply and fix mcb db tpn 4 way vertical type factory made ip 42 protection class metal double door with 200 amp rating bus bar 240 / 430 v for fixing of mcbs / insulator / rccbs etc complete after dismantling old one, complete all as specified and directed. 203 supply and fix mcb db tpn 8 way vertical type factory made ip 42 protection class metal double door with 200 amp rating bus bar 240 / 430 v for fixing of mcbs / insulator / rccbs etc complete after dismantling old one, complete all as specified and directed. 204 supply and fix mcbs 240 / 415 volts 10 ka finger proof terminal, c curve bi connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, isi markedto be fixed on db .note: db will be measured and paid separately under respective items of sch a. 205 mcb tpn 63 amps. 206 mcb tpn 100 amps 207 mcb spn 40 amps. 208 mcb sp 5 to 32 amps 209 material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected toand includinggalvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means ofnuts and bolts, check nuts and washers of gi and connected to earhing test point and earth dollyall as shown in electrical plate no 3 of mes ssr part i and testing on completion includingnecessary excavation and earth work in any type of soil, pcc ( 1:3:6 ) type c1 chamber, pre cast rcc slab 50mm thic in cement concrete ( 1:2:4 ) , type b1, reinforced with welded steel wire fabric or xpm, ( weight not less than 4 kg per sqm ) with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, gi protection pipe, 15mm dia, light grade, 7.5 mtr long for protection of earth lead upto test point etc, complete all as specified and as directed. 210 supply & fix exhaust fan ac single phase 230 v of size 300 mm sweep with louvermetalic body complete by making hole of proper size on existing 9 inch thick brick wall for fixing of exhaust fan, making good the disturbed surface and replstering, repainting the wall surface to match the existing colour, complete all as specified and as directed. 211 supply & fix water heater storage type electric, capacity 25 litres bee 5 star rated with 100 % copper tanks on existing brick wall with help of 04 nos fashners nuts and bolts and making neccesary electric & water connection with 02 nos 300mm long pvc connection with 02 nos brass nuts for connection, complete all as specified and directed. 212 material and labour for meter box of size 0.75 mx0.60 m of .30 m width of ms sheet of 3 mm thickness and a clamping or supporting sheet inside forsuppoting of 4 nos meter and door with 1 nos of transparent glass of 5 mm thicknesssuitable for visibility of 4 nos meter fixed on door with suitable arrangemnets. there should be 8 nos holefor entering of 25 mm dia pipe, meter box shall be fixed in wall and necessary chiseling and meke good of wall to be included in quoted cost drawing of meter box to be approved by ge. 213 disconnecting electricconnection and taking downcarefully energy meter and make proper detail with qtr no having meter serial no and reading while takin down energy meter & depositedto age e / m storeyard andrefixing energy meter in meter box with qtr no wrtitten on meter by black permanet markerall as specified and directed by engr in charge. 214 disconnecting electric and water connection connection and taking downcarefully geyser and depositedto age e / m storeyard andrefixing geyser at same location all as specified and directed by engr in charge. 215 material and labour for replacement of rusted louvers of existing exhaust fan fans 300 mm sweep with new gi louvers, complete all as specified and directed. 216 material and labour for taking down carefully led tube light fitting cleaning and kept in safe custody and refix the same as directed by providing necessary connection copper 3 core wire from ceiling rose to tube light fitting, complete all as specified and directed. 217 external electrification works 218 supply, laying, testing and commissioning in trenches / ducts, fixed on walls / panels of xlpe ltug cable, 1100 volts grade, pvc insulated, pvc unsheathed armoured with aluminum conductorcable complete including lugs ofcross sectional areas of cables size 35 sqmm 3.5 coreincluding taking down old unserviceable cable complete all as directed. 219 supply, laying, testing and commissioning in trenches / ducts, fixed on walls / panels of xlpe ltug cable, 1100 volts grade, pvc insulated, pvc unsheathed armoured with aluminum conductorcable complete including lugs ofcross sectional areas of cables size 25 sqmm 4 coreincluding taking down old unserviceable cable complete all as directed. 220 excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft loose soil for foundation of poles, structures, stay rods, laying of underground cable etc complete all as directed. 221 returning, filling in, including spreading, leveling, watering and well ramming in layers each not exceeding 25cm thick using soil complete all as directed. 222 removing excavated surplussoil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as directed. 223 supply and spreading of natural, clean, dry, river sand in trenches for cable protection / transformer yard / two pole structure yardcomplete all as directed.note: punned thickness only shall be measured for payment purpose. 224 supplying and laying un reinforced precast concrete cable cover, class lv, type 1 with peak, size300mm x 180mm x 40mm, complete all as specified and as directed. 225 supply and lay gi tubing 50mm dia, light grade for cable protection at road crossing / on poles and tubing sealed at bith ends after laying the cables including taking out old gi tubing, complete all as specified and as directed. 226 external water supply works 227 taking out old unserviceable gi pipe line and supply and fixing / laying gi tubing medium grade of following dia, laid in trenches / floors or fixed to walls including necessary gi fittingssuch as bends, elbows, nipple, sockets, unions, reducers, tees etc and making good the surface to match with existing surface, complete all as speified and as directed .note : necessary excavation and earth work shall be measured and paid separately under relavent items. 228 supply and fix gun metal gate valves isi marked with iron wheel head and both ends screwed including removing of unserviceable gun metal gate valve from the existing position of the following size 25mm dia gun metal valves, complete all as speified and as directed . 229 excavation in trenches, not exceeding 1.5mm wide and not exceeding 1.5m in depth for laying of pipe line and getting out in any type of soil, complete all as speified and as directed . 230 returning filling in, including spreading, levelling watering and well ramming in layers not exceeding 25cm thick using soil, complete all as speified and as directed . 231 removal of excavated soil to a distance not exceeding 50mtr and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as speified and as directed . 232 cutting of xisting steel tubing pipe for altration or addition ( each cut ) up 50 m bore pipe, complete all as speified and as directed ....

Indian Army - Punjab

40248051 bids are invited for tata sre ball bearing , tata regulator , tata bearing bush , tata drive assy , stln rectifier , stln regulator total quantity : 6...

Indian Army - Punjab

40235471 bids are invited for tmb assy auto tensioner bs3 4 , tmb roller ac belt tensioner , tmb dg ball bearing , tmb protective cap for bearing , tmb gear fly wheel ring , tata assy compressor 1st pipe with hose , tmb kit pad assy front , tmb kit lined assy total quantity : 9...

Cooperative Sugar Mills Societies - Punjab

40226027 tender for supply of following items and following works supply of seed slurry seed slurry size 3 to 5 micron qty. of sugar 380+10 gm sp gravity 1.89 gm/cm2 coefficient of variation 3% only it should be prepared in special designed machine polymer using high depressive chemicals which prevent agglomeration of fine sugar particles storage unlimited in normal condition packed in 5.0 kg plastic container non returnable. supply of process chemicals {flocculant magnafloc lt 27} magnafloc lt 27 (food grade) with imported uk packing / superfloc 120 v v kemira international usa or any flocculent equivalent to magnafloc lt 27 with imported packing dose: 01 1.5 ppm it should have high molecular weight nontoxic, anionic, polyacrylamide & free flowing white granular powder & its particle size should be 98% less than 1000 um. ph at 1% solution should be 6.8 7.8, free acrylamide less than 0.05% lot number, date of manufacturing & date of expiry must be mentioned on original imported packing of 25 kg bags. supplier will supply food grade certificate note: 1. penalty will be imposed on pro rata basis if dose will increase from 1.5 ppm. 2. import bill must be submitted with the delivery of each consignment. supply of... 15 hp vfd for cane unloader. supply & commissioning of crane duty 15 hp vfd 3 phase, 380v 460 v make schneider/abb for cane unloader crane duty motor hp 15, rpm 970, voltage 415, duty s4, 3 phase, 50 hz warranty one year networking material & installation cat 6 cable mouse cardless logitech poe switch 8 port connectorts wifi doungle supply networking material & installation nrv 16 channel cp plus ip camera 2.0 cp plus hdd 2td toshiba hdmi cable 3 mtr electrical material installation charges supply of ...valve epdm liner for c.i. butterfly valve make crane size 450mm size 400mm size 350mm size 300mm size 250mm size 200mm ci butterfly valve rating pn 3.5 60 psi body ci bearing temp. 180°c ss 304 grade disc and epdm liner gear operated manually isi marked make! crane size 450mm = = 400mm ~01 no. 01 mo supply of ... valve cast steel flanged end globe valve pressure 10 kg/cm2 size 65mm 80 mm cast steel flanged end nrv pressure 10 kg/cm2 size 65mm 80 mm supply pump & pump spares make: gita superheated wash water pump rpm 2900 head 80 mtr capacity 36m³/hr size & type: 40 260 cd 65 drive h.p.: 20 supply of sugar bag handling trolley sugar bag handling trolley heavy duty n made of 6.0 mm thick m.s. angle and flat fitted with teflon wheel of size 8.0 inch dia x 2.0 inch width x 1.0 double inch bore dia with ball bearing complete in all respect suitable to carry the 50 kg sugar bag taflon trolley wheel (with ball bearing) size of wheel dia 8.0 inch dia bore 1.0 inch bore width 2.0 inch supply of cane crusher (horizontal) having cane juice extraction 60 65% power sugar cane crusher is specially designed to walk on 5 hp electric motor suitable for sugar laboratory guarantee to give uniformly higher extraction considerable grader with steel gears and negligible requirement of spare part having small acreage of sugar cane. special features : axles: made of high grade tough steel being fitted to hot runk in to the roller not become loose even under most stemous condition rollers: made of high grade cast iron. grooved to take hold of the sugar cane. side plates: made of high grade cast iron well machined heavy in weight bearings: made of high grade gun metal. technical specifaction: having three roller size as per under size of roller (1) 222mm x 216mm size of roller (2) 152mm x 216mm size of roller (3) 150mm x 216mm delivery of material complete of all respect supply of electric chain block capacity one ton. electric chain block /hoist specification a. capacity :1 ton, b. 20 meter long chain with hook suspension along with load/ test certificate c. make indef other specification induction motor: 40% cdf voltage : 400/440 v, 3 phase, with locking system frequency: 50 cycle /sec, h.p :1.5, (k. w:1.1) amp: 3.6 (fl), motor :rpm 1440, class b insulation isi approved test certificate required along with on off push button water proof with electric cable 20 meter long heavy duty delivery of material complete in all respect: remarks: supplier will supply the list of material. supply of pvc saddle rubber washer saddle rubber washer as per drawing bsm/01/ dated 12.09.2023 pvc bush as per drawing bsm/02/dated 12.09.2023 supply of air dryer for air compressor supply of air dryer for pneumatic system. shetronic refrigerate air dryer. input 100mm dia outlet 100 mm dia pressure range 7 to 10 kg/cm² for pneumatic system. capacity of air compressor : 3.0 400 m³/hr: microscope having fixed stage with precision mechanical stage for x and y movement of slide up to 50x75 mm. buit led light, electrical system and regulator,vertical microscope is designed for measuring of sugar crystal in the sugar factories. a magnifica mage of the objective in the plain of the ocular scale mounted in the eye piece and from threading on the scale, the size of the crystal determined is calculation help of the chart which is supplied with the microscope. the complete microscope with eye piece of 10 x fitted with micrometer scale and the objective of 5x, 10 x,20x,45 x microscope design for accurate and quick examination of the (a) refractive index (b) mean dispersion or liquids, solids & power. technical specifications refractive index nd range nd range refractive index refractive index nd range 0.0005 brix (%age) range 0 95 brix (% age) min .div range 1.300 1.700 0.0002 0 25 tmerature range u degree 70 degree centigrade 01 0 microscope it is a high class projection crystal measuring microscope having wide application in the field of sugar factorie, its various models make it hightly suitable for different processes kluding group discussions technically and research in sugar laboratories,a special model for help in calculating in sugar crystals.the compte projections crystals measuring microscope projection scree inchi round with scale and objective 5x,10 x, 45x and 100 x oil imrsion imported with objective slide 1 mm diveded in to 100 divisions of rma japan make imported lab. chemicals make: ranbaxy/glaxo/qualigen sulphuric acid 98% pure hydrochloric acid 36 40% 2.5 lire packing rectified sprit denatured sprit lead sub acetate 5 kg packing pot iodide cp quality ammonia cp quality buffer tablets ph 7 0 ph 4 0 btb. powder chlorophenol red powder erichrome black t universal indicator solution 500 ml. universal indicator solution 125 ml btb solution 125ml. ph test paper range 10 strips in une packet 3.8 to 5.4 4.8 to 6.4 7.6 6.0 to 6.8 to 8.4 fehling solution a 8.0 to 9.6 fehling solution b whatman filter sheets size 46x57 orignal packing of 100 sheets hand made circular filter paper 18.5 cm kalpi make (50 circle in one packet) commercial i grade formalin 50 litre pack table type p.h metre range 0 14 gl.ss electrode toshinwall care/integral aquasol/ double distillation set having two flasks of 5000 ml with condensers stand and sensors thermometer range 0 to 100 degree mercury in red colour thermometer range 0 to 500 degree mercury in red colour brix hydrometer germany make range 0 to 10 range 10 to 20 range 20 to 30 phenolphtlein indicator 25 gram pack erichrome black t indicator 25 gram supply of ...color coated sheet make tata, jindal color coated sheet zinc aluminium alloy coating 150 gsm width 1220mm thickness 0.5mm top 25 micron top colour blue back colour light grey length 12.200mtr supply of ...color coated sheet make tata, jindal color coated sheet zinc aluminium alloy coating 154 gsm width 1220mm thickness 0.5mm top 25 micron top colour blue back colour light grey length 12.200mtr supply of ...color coated sheet/ridges make tata, jindal color coated ridges zinc aluminium alloy coating 150 gsm thickness 0.5mm top 25 micron top colour blue back colour light grey length 3 mtr width 610 mm make tata, jindal color coated sheets zinc aluminium alloy coating 150 gsm thickness 0.5mm top 25 micron top colour blue back colour light grey length 1.6 mtr width 1220 mm supply of ... gun metal gear for rgb bronze gun metal gear for rgb u 1200 od 560mm no. of teeth 40 width 60mm supply of water flow meter with totalizer electromagnetic water flow meter with totalizer lining rubber flange and max. opt pressure 20 kg/cm² input power supply 230 vac, accuracy ± 0.5% protection ip65 display remote led display panel mount with 10 meter wire output singed 4 20nos. size 1500mm make brio/ dms/forbes marshall/r well size 4.0 inch dia size 6.0 inch dia accuracy+/ % fsd optional: +/ 5% fsd. (auto cut unloading pressure device) remarks: calibration certificate to be provided from concerned department. supply of forged steel of continuous centrifugal machine dc 10/34 spare for wil make continuous centrifugal machine type dc 10 / (34 deg) forged head steel shaft en 24 duly machine bearing sizes grinded supply of ... tyre coupling & spare tyre tyre coupling complete make fenner spare tyre make fenner supply of air blower air blower (without motor) make: tmvt (manik lal) twin lobe air blower capacity: 1200 cubic meter discharge pressure: 1.0 kg/cm² along with safety valve servicing/overhauling batch type centrifugal machine. g 1250 uttam make. manufacturing contract work fabrication & erection amc of online monitoring system at etp ...

Indian Army - Punjab

40198198 bids are invited for tss mt carburator bs 29 , ball bearing , hand primer , switch assy comb and lock , revolution counter , shround fan , hub lock , pump assy , major rep kit for m cyl , wheel box , dust boot gear box , carpet centre floor rh , fuel pressure pipe , sleeve cyl rep kit minor total quantity : 22...

Indian Army - Punjab

40106922 bids are invited for lv7 / tata 2547 092 0127 assy wheel chock lv7 / tata 2618 4010 0102 assy wheel nut lv7 / tata 2786 0798 9925 assy fly wheel lv7 / tata 2523 0310 3101 ball bearing lv7 / tata 2097 2850 0101 bearing assy lv7 / tata 2573 3530 3102 bearing cyl roller ( for tail pinion ) lv7 / tata 3110 107083 bearing roller taper lv7 / tata 6210 000332 blinker lamp lh lv7 / tata 2505 2630 3104 brg taper roller lv7 / tata 2636 1540 0102 brush box assy lv7 / tata 2525 0516 7901 bush rod lv7 / tata 5365 183803 bushing rubber lv7 / tata 5365 183751 bushing sleeve lv7 / tata 3120 104492 bushing sleeve lv7 / tata l01402000041 brush gear assembly lv7 / tata 2154 891 0010 cab lifting bar lv7 / tata 2505 2671 8222 cap lv7 / tata 312 267 1096 cap rubber protective ( on gear box top ) lv7 / tata 2523 1813 3201 centre pin filter cover to filter hsg lv7 / tata 000 585 0088j chassis record beg total quantity : 817...

Indian Army - Punjab

40057790 bids are invited for boq tss tata sre ball bearing , tata regulator , tata bearing bush , tata drive assy , stln rectifier , stln regulator total quantity : 6...

Kendriya Vidyalaya Sangathan - Punjab

40038731 bids are invited for lab apron , lab protective eye glasses , droppers glass , test tube cleaning brushes , protective gloves , ph paper strip , litmus paper strip , test tube holder , china dish , dropper plastic , platinum wire , ethanal , potassium hydroxide , magnesium dioxide , oxalic acid , silver nitrate solution , filter paper , mohrs salt , potassium permagnate , ethanol , acetone , ethanoic acid , boiling tube , test tube holder wooden , china dish 3 inch , petri dish 3 inch , spatula steel , distilled water , test tube cleaning brush small , test tube cleaning brush large , beaker 100 ml , measuring cylinder plastic 10 ml , measuring cylinder plastic 50 ml , tesla coil , tuning fork , sand clock , aluminium metal chips 500gm , drawing board wooden , magnesium ribbon 1 roll , starch 250 gm , diy kits , static electricity , magnetism , electromagnetic effects , dispersion , tyndall effect , reflection , refraction , stethoscope , pendulum , sphygmomanometer , structure of atom bohr model , ball bearing , electrolysis apparatus , morter pestle for grinding , raxine chart , dissection blade , camel brushes , urea , needle with plastic handle , model , specimen model , permanent slide , cavity slides , cover slips , needles with plastic handle , aluminium metal chips , yeast powder , glycerine , screw gauge , springs for spring balance , tuning fork set , copper hollow rod , dcc wire , constantan wire , manganin wire , rubbre pad for tuning fork , glass prism , hollow prism , convex lens , concave mirror , ammonium chloride , zinc rod , nylon plastic thread , glycerine , optical pins thick 40 to 50mm long , pipe for resonance tube , pinch cock for resonance tube 1 58 total quantity : 386...

Indian Army - Punjab

39935279 bids are invited for mt spares clutch plate , ball bearing , fuel pipe , pressure plate , fog light 12v , cartridge oil filter , filter element , seperator fuel water , relay assy , head lamp fg 122n , fuel filter , blade assy wiper , lining shoe , wiper motor , v belt b62 total quantity : 47...

Public Works Department - Punjab

39889906 providing and fixing furniture items at various aam aadmi clinics at bhucho mandi, sema, bhai rupa, rampura and ramnagar under the jurisdiction of provincial division, pwd, bathinda 2 chair for receptionist and pharmacist & lab assistant providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60µ thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 4 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee 3 waiting area chair 3 seater supplying & placing three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60µ (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm of reputed brand/make except chinese complete as per approved drawings by furniture committee 4 waiting area chair 2 seater supplying & placing two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50µ (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm of reputed brand/make except chinese complete as per approved drawings by furniture committee 5 doctor table supplying & placing executive table with credenza unit in completely knock down conditions with table size 1800mm x 750mm x 750 mm and side cabinet 900 mm x 400 mm x 750 mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 900mm x 400mm x 750mm made up of 25mm thick pre laminated particle board of grade ii of is 12823. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 900mm x 400mm x 750mm. it should be made up of pre laminated particle board of grade ii of is 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380 of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee 6 main chair for doctor providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60µ thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee 7 visitor chair for doctor providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60µ thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee 8 examination table for doctor room providing and placing in position examination table with two section top with fix mattress ( overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h). the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 40x40 section 2 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. the bed should be provided with 40 density 50mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealedof reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee 9 stool for doctor, pharmacist room & in samplingroom revolving stool made of 32 od mm and 25 od mm ms pipe, top made of ss steel plate heavy gauge frame powder coating of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee 10 storage for medicine/ customised lab table providing, supplying and placing storage almirah. the overall size of the almirah shall be 600mm (w) x 900 mm (d) x 750mm (h). the almirah shall be supplied with 2 nos. of wodden doors with2 nos. of adjustable shelves i.e. 3 loading compartments. it should be of 25mm thcik prelaminated particle board of grade ii of is 12823the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength complete as per approved drawings by furniture committee 11 big storage for medicine 1 no. no in pharmacy providing, supplying and placing steel almirah. the overall size of the almirah shall be 915 mm (w) x 485mm (d) x 1980mm(h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 5mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50µ thick of reputed brand/make except chinese complete as per approved drawings by furniture committee. 12 providing and fixing at site the reception table plan dimensions as 5’ 6” x 19 & 29 x 1’5” and height 2’ 6” with storage, drawers, space for legs, etc complete as per drawing. the table should be sturdy and stable and will comprise of knot free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of make and colour to be approvedby architect/ engineer in charge. the item also includes hardware such as drawer channels, handles, etc of make and design to be approved by architect/ engineer in charge. the item also includes all types of consumables such as nails, screws, fevicol, tape, etc and polishing, if required.grooves, wherever required as per drawing, are also included in the item.complete as per drawing/design (attached) as decided by furniture procurement committee. 13 providing and fixing at site the pharmacy tableplan dimensions as 1200 x 600 x 750 mm with projected shelve, storage, drawers, space for legs, etccomplete as per drawing.the frame structure shall bemade up of ms crca tata/ bhushan 0.8 mm thickness . the counter should be sturdy and stable and will comprise of knot free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of make and colour to be approvedby architect/ engineer in charge. the item also includes hardware such as drawer channels, handles, nails, screws, fevicol, tape, etcpolishing and grooves if required., wherever required as per drawingof reputed brand/make except chinese decided by furniture procurement committee. 14 providing and placing moveable 3 fold screen of crca/ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the curtain material should be of cotton fabric and specially coated which do not allow any bacteria hold on it. the ms frame will be 19.05mm (od) x 1.22mm and base material 25mm (od) x 1.22mm of ms powder coated in colour over priming coat complete as per approved drawings by furniture committee. ...

Public Works Department - Punjab

39868770 providing and fixing furniture items at various aam aadmi clinics at village singo, pathrala, giana, kotbakhtu, nahianwala, khemuana and kalalwala under the jurisdiction of construction division no 2, pwd (b and r), bathinda , chair for receptionist and pharmacist & lab assistant providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 4 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee , waiting area chair 3 seater supplying & placing three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm of reputed brand/make except chinese complete as per approved drawings by furniture committee , waiting area chair 2 seater supplying & placing two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm of reputed brand/make except chinese complete as per approved drawings by furniture committee , doctor table supplying & placing executive table with credenza unit in completely knock down conditions with table size 1800mm x 750mm x 750 mm and side cabinet 900 mm x 400 mm x 750 mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 900mm x 400mm x 750mm made up of 25mm thick pre laminated particle board of grade ii of is 12823. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 900mm x 400mm x 750mm. it should be made up of pre laminated particle board of grade ii of is 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380 of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee , main chair for doctor providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee , visitor chair for doctor providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee , examination table for doctor room providing and placing in position examination table with two section top with fix mattress ( overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h). the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 40x40 section 2 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. the bed should be provided with 40 density 50mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealedof reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee , stool for doctor, pharmacist room & in samplingroom revolving stool made of 32 od mm and 25 od mm ms pipe, top made of ss steel plate heavy gauge frame powder coating of reputed brand/make or equivalent except chinese complete as per approved drawings by furniture committee , storage for medicine/ customised lab table providing, supplying and placing storage almirah. the overall size of the almirah shall be 600mm (w) x 900 mm (d) x 750mm (h). the almirah shall be supplied with 2 nos. of wodden doors with2 nos. of adjustable shelves i.e. 3 loading compartments. it should be of 25mm thcik prelaminated particle board of grade ii of is 12823the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength complete as per approved drawings by furniture committee , big storage for medicine 1 no. no in pharmacy providing, supplying and placing steel almirah. the overall size of the almirah shall be 915 mm (w) x 485mm (d) x 1980mm(h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 5mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick of reputed brand/make except chinese complete as per approved drawings by furniture committee. , providing and fixing at site the reception table plan dimensions as 5’ 6” x 19 & 29 x 1’5” and height 2’ 6” with storage, drawers, space for legs, etc complete as per drawing. the table should be sturdy and stable and will comprise of knot free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of make and colour to be approvedby architect/ engineer in charge. the item also includes hardware such as drawer channels, handles, etc of make and design to be approved by architect/ engineer in charge. the item also includes all types of consumables such as nails, screws, fevicol, tape, etc and polishing, if required.grooves, wherever required as per drawing, are also included in the item.complete as per drawing/design (attached) as decided by furniture procurement committee. , providing and fixing at site the pharmacy tableplan dimensions as 1200 x 600 x 750 mm with projected shelve, storage, drawers, space for legs, etccomplete as per drawing.the frame structure shall bemade up of ms crca tata/ bhushan 0.8 mm thickness . the counter should be sturdy and stable and will comprise of knot free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of make and colour to be approvedby architect/ engineer in charge. the item also includes hardware such as drawer channels, handles, nails, screws, fevicol, tape, etcpolishing and grooves if required., wherever required as per drawingof reputed brand/make except chinese decided by furniture procurement committee. , providing and placing moveable 3 fold screen of crca/ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the curtain material should be of cotton fabric and specially coated which do not allow any bacteria hold on it. the ms frame will be 19.05mm (od) x 1.22mm and base material 25mm (od) x 1.22mm of ms powder coated in colour over priming coat complete as per approved drawings by furniture committee....

Indian Army - Punjab

39836352 bids are invited for ( a ) lv7 / tata 2547 092 0127 assy wheel chock ( b ) lv7 / tata 2618 4010 0102 assy wheel nut ( c ) lv7 / tata 2786 0798 9925 assy fly wheel ( d ) lv7 / tata 2523 0310 3101 ball bearing ( it is ) lv7 / tata 2097 2850 0101 bearing assy ( f ) lv7 / tata 2573 3530 3102 bearing cyl roller ( for tail pinion ) ( g ) lv7 / tata 3110 107083 bearing roller taper ( h ) lv7 / tata 6210 000332 indicator lamp lh ( i ) lv7 / tata 2505 2630 3104 brg taper roller ( k ) lv7 / tata 2636 1540 0102 brush box assy ( 1 ) lv7 / tata 2525 0516 7901 bush rod ( m ) lv7 / tata 5365 183803 bushing rubber ( n ) lv7 / tata 5365 183751 bushing sleeve ( 0 ) lv7 / tata 3120 104492 bushing sleeve ( p ) lv7 / tata l01402000041 brush gear assembly ( q ) lv7 / tata 2154 891 0010 cab lifting bar ( r ) lv7 / tata 2505 2671 8222 cap ( s ) lv7 / tata 312 267 1096 cap rubber protective ( on gear box top ) ( t ) lv7 / tata 2523 1813 3201 centre pin filter cover to filter hsg ( in ) lv7 / tata 000 585 0088j chassis record beg total quantity : 817...

Water Supply And Sanitation Department - Punjab

39812607 tender for following work p/f of chock 28 wattt t 5 make crompton, bajaj, anchor or equivalent in room no. 117 & 231 p/f of tube rod 28 wattt t 5 make crompton, bajaj, anchor or equivalent in room no. 117, 126 & 231 supply of glass make borosil (1 box= 6 piece) in room no. 211 p/f of telescopic channel for computer table in room no. 220 rewinding charges of ceiling fan 56 size with copper winding insulation material and two ball bearing in room no. 208 p/f of chock 2x36 (double chock) make crompton or equivalent room no. 214 p/f of four pin tube rod 36 watt make bajaj, crompton or equivalent in room no. 214 p/f of double chock 2x28 watt t 5 make crompton or equivalent in room no 126 carriage providing and supply of 4kva stabilizer for 1.5 ton air conditioner make voltas or equivalent, installation, dismantling of old a.c., copper pipe, three core wire 2.5 mm, drain pipe, powder coated outdoor stand etc for room no. 203 at dwss, head office patiala....

Border Roads Organisation - Punjab

39811136 supply of spares for jessup road roller , supply of spares for jessup road roller , brake strap completejaq77576a , roller brg jaq78013/3 , ball bearing (6214)jaq79013/6 , bevel pinionjaq79010a , locking washerjat79015 , bushjaq79022 , oil pressure gauger14a , fuel pipe57715 , fuel pipe filter to enginejaq78004a , pre filter element (1.1 ltr cl oth)48.117.01.0.00 , micro filter element (1.1 ltr paper)48.117.02.0.00 , spiral bevel pinionjah79051 , spiral bevel pinion forwardjah79181 , 1st inter shaft & pinionjaq79059a , sprial bevel wheeljaq79191 , ball bearingjaq78013/11 , bevel wheel rh jah79205a , bushjaq79026 , oil seal jat79236 , spring ringjat79195 , ball bearingjaq78013/14 , universal couplingjaq89171 , key for universal couplingjaq78011/2 , key jaq79165a , pin for axle capjat79164a , hind axle capjaq79163a , bush for rear rolljaq89422 , hind roll scrapper support bkt52354 , hind roll scrapper blade57952 , rubber hose top 57840c , clutch housing oil seal innernk , clutch housing oil seal outernk , king pin rep kit std_257633200120...

Border Security Force - Punjab

39807063 bids are invited for spares parts for tvs motor cycle cylinder piston and lock set std , ring set , valve inlet and exhaust , valve guide inlet and exhaust , valve seat inlet and exhaust , valve oil seal , timing gear cam , timing chain , timing chain tensioner , trimming chain guide set , head gasket , valve adjusting screw , over haul gasket set , connecting rod with bearing , ball bearing set crank lh and rh , over hauling oil seal set , spark plug , plug cylinder head , ball bearing 30x55x13 input shaft bearing , gear complete kick start idle kick idle gear , air filter , clutch pressure plate , hub clutch , disc clutch pressure , carburettor assy , throttle cable , clutch cable , accelerator cable , mudguard front , clutch handle with yoke and nut bolt , rear view mirror lh side , rear disc plate , rear disc brake pad , rear calliper kit , rear brake master cylinder repair kit , rear wheel bearing inner , rear wheel bearing outer , rear hub wheel , rear hub bearing , rear hub damper rubber , rear shock absorber lh , foot peg nut with bolt 12 mm , chain sprocket nut with bolt , front small sprocket bolt 10mm , front brake calliper assy , front brake pad , front shock absorber oil seal , front fork inner tube , banjo washer 12 no , front rh rear view mirror , engine oil filter , petrol pipe , ana bond tube , rust cleaner , cotton waste , cam quarter lock , handle weight with nut and bolt , handle cone set bearing , rear rh side indicator assy with bulb , rear lh side indicator assy , front side indicator assy with bulb , clutch switch assy , t horn set high and low tune , fuel float assy , parking bulb 12 v , insulation tape , plastic tape roll , contact comp gear shift switchn eutral patti , neutral switch , magnet assy , head light switch assy rh side , brake light switch assy foot , brake light switch front hand , fuel sending unit 1 49 total quantity : 105...

Department Of Heavy Industry - Punjab

39807003 bids are invited for ball bearing 6204 material code 551110620400 (q3) , ball bearing 6205 2rs material code 551190620500 (q3) , ball bearing 0132 material code 552115111400 (q3) total quantity : 1100...

Water Supply And Sanitation Department - Punjab

39786640 tender for 1. p/f of chock 400 watt make crompton or equivalent (street light) p/f of lamp 400 watt make crompton. ==> iii. p/f of brass holder 400 watt street light. iv. p/f of integral ignitor hps. v. p/f of 240v capacitor make crompton. vl p/f of 32 ampere mcb make havells, fine, anchor or equivalent. vii. p/f of 4 sq mm copper wire make havells, shalimar or equivalent. viii. p/f of flood light 100 watt (led) make crompton. ix. p/s of plastic pipe size 1 make flex, standrat, jindal or equivalent. x. carriage. repair of 2 no. grass cutting machine with material as per below: 1. base welding electric ii. pulley iii. leverage iv. stud v. filling for machine we. nut & bold with washer vii. ball bearing for machine viii. belt ix. ball bearing for pully machine x. pvc wire three core 2.5 sq mm copper make havells, shalimar or equivalent...

Department of Cooperation - Punjab

39783486 tender for for the disposal of unserviceable material 2 poly film pouch scrap 3 gatta scrap 4 polythene liner 25 kg smp old 5 kraft paper bags smp25 kg old 6 plastic trays old 7 transport scrap 8 iron scrap 9 aluminum can old 10 aluminum lid scrap 11 ball bearing assorted size old 12 electric scraps 13 gun metal scrap 14 plastic rubber/ polypropylene bottle scrap 15 battery assorted size scrap 16 empty ghee tin ½ ltr, 1 ltr, 2ltr, 5 ltr, 17 wmp tin 1/2 kg, 1 kg 18 empty ghee tin 15 kg / wmp tin 10 kg 19 jerry can plastic cap. 50 ltr. / 70 ltr./ 25 ltr. / 35 ltr. 20 plastic bag (empty) 21 ln2 container(big) 22 steel can capacity 40 litre. scrap 23 stainless steel scrap 24 tyre 1000 20 & tubes flaps assorted size 25 tyre 900 20, 715 16, motor cycle tyre etc.& tubes flaps assorted size 26 compressor assorted size 27 deep freezer/ice candy/chest cooler 28 computer spare parts/scrap 29 newspaper/booksscrap 30 dahi cup/ kheer cup broken 31 visi cooler 32 freeze 33 centrifugal machine 34 double distilation unit 35 milk pump 3hp 36 ceiling fan /wall fan 37 generator set without battery 38 bmc tank 1000 ltrs 39 bod incubator 40 motor (1hp) 41 motor (2hp) 42 motor (3hp) 43 motor (5hp) 44 motor (7.5hp) 45 motor (10 hp) 46 frame crank 47 moisture analyser 48 milko screen minor 49 ghee ceka 1ltr,1/2 ltr 50 pio sterlizer 51 pio filler machine 52 pio bottle washer 53 soft water tank cap 15000 ltr 54 vacuum pump 7.5 hp 55 gear box 56 indoor & outdoor fan 57 transformer 750 kva 58 milk chiller cap 5000 alfa level 59 milk chiller cap 20000 hmt 60 chaff cutter 61 homogenizer 62 paneervat cap 600 ltr ...

Public Works Department - Punjab

39672814 providing and installation of furniture in aam aadami clinic (aacs) in hospital building at dhandaur (block adampur rural) in distt. jalandhar and porta cabin aam aadmi clinic (aacs) at janj ghar birring in distt. jalandhar (phase v) , i) providing & installation of furniture , chair for reception providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. , waiting area chair 3 seater supplying & placing three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , waiting area chair 2 seater supplying & placing two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm. , doctor table supplying & placing executive table with credenza unit in completely knock down conditions with an overall size 1600mm x 1600mm x 750mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 800mm x 500mm x 750mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 1400mm x 575mm x 500mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , main chair for doctor providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm. , visitor chair for doctor providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm. , examination table for doctor room providing and placing in position examination table. overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h. the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. it shall be provided with 30 mm thick mattress. the bed should be provided with 40 density 30mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealed. complete as per sample approved by architect & desired by engineer in charge. , chair for pharmacist supplying and placing ergonomically designed, comfortable & aesthetically appealing mid back chair. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. the same shall be upholstered with leatherite tapestry 0.8mm thick and 535 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine. moulded pp arm shall be used with cushion and leatherite upholstery. for seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suite them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load. the seat size shall be 515±10mm(w) x 490±10mm(d) and back size shall be 510±10 (w) x 510±10mm(h) from seat & overall height = 945±10mm. , stool for doctor, pharmacist room & in samplingroom revolving stool, ss top, powder coated, height adjustable (510mm 690mm). complete as per sample approved by architect & desired by engineer in charge. , storage for medicine providing, supplying and placing steel almirah. the overall size of the almirah shall be 915mm (w) x 485mm (d) x 1980mm (h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick. , customized lab table supplying & placing storage unit with an overall size 1800mm x 600mm x 900mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. the sliding shutter shall be operated on sliding rail track and ss handle as well as push lock mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. , providing and placing moveable 3 fold screen of ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the ms frame will be powder coated in colour as complete as per sample approved by architect & desired by engineer in charge. , providing and fixing roller blinds at the designated locations with fabric/ texture complete as per sample approved by architect & desired by engineer in charge. , provding and placing of steps for examination table in doctor room approved by the architect/ engineer in charge...

Public Works Department - Punjab

39651469 providing and installation of furniture in various aam adami clinics (aacs) (phase v) at guru ravidass dharmshala, arya nagar kartarpur (urban), vill. mallian block kartarpur rural and vill. nijjran block kartarpur rural in distt. jalandhar. , providing & installation of furniture chair for reception providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. , waiting area chair 3 seater supplying & placing three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , waiting area chair 2 seater supplying & placing two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm. , doctor table supplying & placing executive table with credenza unit in completely knock down conditions with an overall size 1600mm x 1600mm x 750mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 800mm x 500mm x 750mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 1400mm x 575mm x 500mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , main chair for doctor providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm. , visitor chair for doctor providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm. , examination table for doctor room providing and placing in position examination table. overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h. the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. it shall be provided with 30 mm thick mattress. the bed should be provided with 40 density 30mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealed. complete as per sample approved by architect & desired by engineer in charge. , chair for pharmacist supplying and placing ergonomically designed, comfortable & aesthetically appealing mid back chair. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. the same shall be upholstered with leatherite tapestry 0.8mm thick and 535 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine. moulded pp arm shall be used with cushion and leatherite upholstery. for seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suite them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load. the seat size shall be 515±10mm(w) x 490±10mm(d) and back size shall be 510±10 (w) x 510±10mm(h) from seat & overall height = 945±10mm. , stool for doctor, pharmacist room & in samplingroom revolving stool, ss top, powder coated, height adjustable (510mm 690mm). complete as per sample approved by architect & desired by engineer in charge. , storage for medicine providing, supplying and placing steel almirah. the overall size of the almirah shall be 915mm (w) x 485mm (d) x 1980mm (h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick. , customized lab table supplying & placing storage unit with an overall size 1800mm x 600mm x 900mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. the sliding shutter shall be operated on sliding rail track and ss handle as well as push lock mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. , providing and placing moveable 3 fold screen of ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the ms frame will be powder coated in colour as complete as per sample approved by architect & desired by engineer in charge. , providing and fixing roller blinds at the designated locations with fabric/ texture complete as per sample approved by architect & desired by engineer in charge. , provding and placing of steps for examination table in doctor room approved by the architect/ engineer in charge...

Indian Army - Punjab

39559267 bids are invited for seal oil , bearing ball s row , bearing ball journal single row , ball valve 50 mm , suction nozzle , ball bearing centre , compound gauge , pressure gauge , oi seal , bearing ball d row 90x40 , bearing total quantity : 13...

Department of Cooperation - Punjab

39557868 sale of unserviceable material on one time sale basis rate contract , ms iron scrap mix , ss scrap mix , aluminium scrap mix , batteries mix , copper wire burned pieces , tyres mix , tube/ flaps mix , transport scrap , plastic scrap mix , used lubricant oil with iron drum , window ac , deep freezer & chest freezer mix , fan with exhaust fanmotor , electrical motors & pump mix , vaccum cleaner , aluminium lid , aluminium can without lid(40 ltr) , visi cooler , a i container ln2 , ball bearing mix , prepack m/c ss w/o motor/transformer , lactoscan vibrator , electrical panel box ms , cream seperator without motor , transformer 315 kva , fat testing/centrifudge machine , gyser assorted , ss air curtain with motor , paint sprayer machine , inverter mix , printer big ms , ss lid , ss can w/o lid , generator phm 20 c2 w/o canopy , chilled water valveg metal , chilled water valve m s , voltage stabilizer / battery charger mix , sealing fan/wall farn/ex fan mix , solo star wheel without motor , exhaust blower , rotary valve without motor , ss valve mix (51 mm, 65mm etc.) , vaccum pump (mazda) , chilled water radiator , nitrogen filter , steam radiator , air compressor cooling tower , milk pump for bmc 1000ltr. , dg set for bmc 1000ltr. , control panel for bmc 1000ltr. , compressor for bmc 1000ltr. , tanki ss for bmc 1000ltr. , starter for bmc 1000ltr....

Border Security Force - Punjab

39408430 bids are invited for spare parts of tvs apache motorcycle cylinder piston and lock set std , ring set , valve inlet and exhaust , valve guide inlet and exhaust , valve seat inlet and exhaust , valve oil seal , timing gear cam , timing chain , timing chain tensioner , trimming chain guide set , head gasket , valve adjusting screw , over haul gasket set , connecting rod with bearing , ball bearing set crank lh and rh , over hauling oil seal set , spark plug , plug cylinder head , ball bearing 30x55x13 input shaft bearing , gear complete kick start idle kick idle gear , air filter , clutch pressure plate , hub clutch , disc clutch pressure , carburettor assy , throttle cable , clutch cable , accelerator cable , mudguard front , clutch handle with yoke and nut bolt , rear view mirror lh side , rear disc plate , rear disc brake pad , rear calliper kit , rear brake master cylinder repair kit , rear wheel bearing inner , rear wheel bearing outer , rear hub wheel , rear hub bearing , rear hub damper rubber , rear shock absorber lh , foot peg nut with bolt 12 mm , chain sprocket nut with bolt , front small sprocket bolt 10mm , front brake calliper assy , front brake pad , front shock absorber oil seal , front fork inner tube , banjo washer 12 no , front rh rear view mirror , engine oil filter , petrol pipe , ana bond tube , rust cleaner , cotton waste , cam quarter lock , handle weight with nut and bolt , handle cone set bearing , rear rh side indicator assy with bulb , rear lh side indicator assy , front side indicator assy with bulb , clutch switch assy , t horn set high and low tune , fuel float assy , parking bulb 12 v , insulation tape , plastic tape roll , contact comp gear shift switchn eutral patti , neutral switch , magnet assy , head light switch assy rh side , brake light switch assy foot , brake light switch front hand , fuel sending unit 1 49 total quantity : 105...

Indian Army - Punjab

39337950 bids are invited for wheel nut , assy plastic reserve tank , brg front , brg rear generator , bearing , gauge water temperature , fd coil assy , clutch cyl repair kit , door lock assy lh , catch assy bonnet catch , ball bearing , rectifier plate assy , regulator , wiper blade and arm assy , u clamp lh total quantity : 30...

Indian Army - Punjab

39173803 bids are invited for rear sprocket thirty eight teeth , wiper blade assy , tail lamp assy rh , cylinder head gasket , assy hose , rubber moulding glass , kit brake lining front , dual brake valve kit , repair kit brake actuator , seal oil for crank shaft , wiper motor assy , ball bearing , clutch cylinder rep kit total quantity : 25...

Indian Army - Punjab

39122093 bids are invited for boqboq positione assy , armature assy , seal oil for crank shaft frt , isolator switch , clutch kit , cabin lifting pump , control vlave , ball bearing 3303 , voltage regulator total quantity : 29...

Indian Army - Punjab

39122070 bids are invited for boqboq positinor assy , armature assy , seal oil for crank shaft frt , isolator switch , clutch kit , hand pump cabin lifting , control valve , ball bearing 3303 , voltage regulator total quantity : 29...

Public Works Department - Punjab

39061918 providing and fixing various types of furniture in judicial court complex rajpura distt patiala , retiring room , big table ( w1650 x d1650 x h750 ) with side unit: providing & fixing modular table in completely knock down conditions with an overall size 1650mm x 1650mm x 750mm that is to be assembled at site. the construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. the work top shall have the size 1650mm x 750mm made up of 25mm thick particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the table top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the table top shall be supported over particle board base gable end. the end wall of the table on the side shall be topped by gable end. the gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. it should be 18mm thick pre laminated particle board with appropriate pvc edge banding connected with both end. there shall be buffers provided at the base to avoid scratches on the floor. the table shall be supplied with side unit for storage purpose with an overall size 900mm x 450mm x 750mm. the side unit shall be made up of pre laminated particle board of grade ii of is 12823 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc. it shall have 2 sliding shutter which slides over sliding rail track. the shutter shall be operated with the assistance of ss handle and multi purpose ( mp ) locking mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. a mobile pedestal shall be provided with an overall size 400mm x 450mm x 680mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel having to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the pedestal shall be mounted over 50mm injection moulded nylon castor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, issued by nabcb aaccredited labs, bifma membership and aiota certification. the oem should have green guard certification issued by ul for one or more products. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , centre table 1200 x 600 providing & fixing center table with an overall size 1200mm x 600mm x 450mm. the top of the table shall be made up of 25mm thick pre laminated particle board of grade ii of is 12823. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on ms powder coated pipe frame having cross section area 30mm x 30mm. the table under structure shall consist of ms / crca chrome plated round pipe having dia. 28mm. there shall be ppcp shoe provided at the base to avoid scratches on the floor. , small table mega corner table ( 600 x 600 ) . s.s. pipe frame, chrome finish, toughened glass, top 12mm thick providing & fixing corner table with an overall size 600mm x 600mm x 450mm. the top shall be made up of 12mm thick toughened glass. the profile shall be in square shape with round corner and bevelled edges. the top shall be supported on vacuum caps situated over ss 202 grade pipe frame. the under structure shall consist of ss pipe frame having size 40mm x 20mm. 1 nos. foot step shall be provided between the frame with the size 40mm x 20mm. there shall be ppcp shoe provided at the bottom to avoid scratches on the floor. , computer table 2 ( 1200 x 600 ) providing & fixing computer desk of size 1200mm ( w ) x 600mm ( d ) x 750mm ( h ) . it should have work top made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit theboard panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top board shall be supported on fixed pedestal at one end and fixed cpu unit at another end. the desk shall be clad with 18mm thick modesty panel which provide structural support for the desk. it should be 18mm thick pre laminate particle board connected with both end.key board trey shall be provided 18mm thick pre laminated particle board with an overall size 550mm x 350mm. the trey shall be operated by sliding channel runs on nylon roller to smooth operation. fixed pedestal shall be provided at one side with the size 335mm x 470mm x 725mm having 3 drawer operated on sliding channel and 1 filing drawer having operated on ball bearing channel. all drawer shall be operated with ss handle with multi purpose ( mp ) locking mechanism. openable storage shall be provided at another side with the size 294mm x 450mm x 725mm having one adjustment shelf to accumulate cpu. complete understructure made in 18mm thick pre laminated particle board with appropriate edge banding and drawer base shall be 9mm thick. to protect the wall from kicks, abrasion and serve as a decorative moulding skirting shall be provided at bottom.the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, issued by nabcb aaccredited labs, bifma membership and aiota certification. the oem should have green guard certification issued by ul for one or more products.the board used should meet international standards of quality and safety, indian standard is12823 grade ii should meet long time loadbending, screw–withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , revolving chair ( officer ) ( high back chair, pp arm, gas lift, nylon base, leatherette tapestry providing & fixing ergonomically designed, comfortable & aesthetically appealing high back chair. the seat shall be made of 15mm thick hot pressed malaysian plywood with hr polyurethane foam 50mm thick having density 40kg / m³ upholstered with leatherite tapestry in black colour with 0.8mm thick and 535 gsm and the back shall be made of double layeredmalaysian moulded hot pressed plywood ( 12+6 ) mm thick with hr polyurethane foam 30mm thick having density 32kg / m³ upholstered with leatherite tapestry in black colour with 0.8mm thick and 535 gsm. headrest shall be provided for comfort of head. seat and back shall be joined with hr steel sheet. the armrest shall be used pp arm fixed type completely joint with seat. the chair shall have synchro knee tilt revolving mechanism with four position locking and tilt tension adjustment. the pneumatic seat height adjustable 100mm with bifma standard class 3 gaslift. the pedestal shall be made up of injection moulded black nylon having pitch circle dia 700 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 480±10mm ( w ) x 495±10mm ( d ) and back size shall be 750±10mm ( h ) from seat & overall height = 1230±10mm. , sofa set ( 2+2 ) seater providing & fixing a two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density 40kg / m³ in seat and 32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having density 40kg / m³. the base of the arm shall have ss frame supported on pre laminated particle board. the structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and 571 gsm. the understructure shall be supported by pipe frame leg of ss. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 500±10 mm ( d ) x 1120±10 mm ( w ) , seat height = 420±10 mm, overall width = 1400±10 mm, overall depth = 790±10 mm & overall height = 660±10 mm. , chairs ( chrome plate ) providing & fixing visitor chair ergonomically designed for user comfort & shall have asthetically appealing design. the seat shall be made of 15mm thick hot pressed malaysian plywood with hr polyurethane foam 50mm thick having density 40kg / m³ upholstered with leatherite in black colour with 0.8mm thick and 535 gsm and the back shall be made of double layered moulded hot pressed malaysian plywood ( 12+6 ) mm thick with hr polyurethane foam 30mm thick having density 32kg / m³ upholstered with leatherite in black colour with 0.8mm thick and 535 gsm. the frame shall be cantilever support made up of ms crca chrome plated round pipe of dia 25.4mm with 2mm thick. the armrest shall be covered with wooden arm. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 475±10mm ( w ) x 490±10mm ( d ) and back size shall be 470±10mm ( h ) from seat & overall height = 930±10mm. , almirah ( 915 x 485 x 1980 ) providing & fixing steel almirah in perfectly upright and straight position. the overall size of the almirah shall be 915mm ( w ) x 485mm ( d ) x 1980mm ( h ) including legs. it should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. stiffeners shall be provided in shelf & door. the steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 40kg maximum. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50 60?. , book rack 4dr book case ( w915 x d320 x h1750 ) providing & fixing metal book case with an overall size 915 mm ( w ) x 320 mm ( d ) x 1750mm ( h ) . the book case shall be supplied with 4 nos. of individual compartments. top, back & side panels shall be made of 0.8mm and rest 1mm high yield strength crca sheet of grade ‘d’ confirming to is: 513. each door shall have individual locking provision and 4 mm thick transparent glass for clear inside vision secured in a metal frame through rubber gasket. each door shall have scissor mechanism for receding inside the top of respective compartment which ensures parallel & smooth movement. each door shall have plastic side end caps as handle which is easy to grip. each compartment has a storage shelf having uniformly distributed load capacity of each shelf is 40 kg maximum. the finish is epoxy polyester powder coated to the thickness of 40 60?. adjustable leveler shall be provided with metal insert to resist scratches on the floor and also level & support structure. , table top 600x450 mm providing & fixing wooden laptop stand table top desk organizer for writing / sketching stand, wooden desk organizer ( brown, big size 600x450 mm ) . portable, adjustable, foldable.uses for office purpose, it maintains privacy, reduces strain on eyes, helpful in no cervical pain, improves handwriting, when you do work on it your work efficiency increases. , court room , big desk table ( w2400 x d2300 x h750 ) providing & fixing executive table with credenza unit and pedestal in completely knock down conditions with an overall size 2400mm x 2300mm x 750mm that is to be assembled at site. the worktop shall be 43mm thick having the combination of 18mm pre laminated particle board with approved laminate and shade as top and 25mm medium density fibre board as base top. the worktop shall have the size 2400mm x 1100mm having the profile in rectangle shape and the edges ( top ) shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius and deco paint with half round post form edges along with grooves ( base top ) . the top shall be supported on 4 nos. of ss pipe strips having size 230mm x 60mm x 15mm. the table shall be clad with 48mm thick modesty panel which provide structural support for the table. it should be 48mm thick pre laminated particle board in linear shape with appropriate pvc edge banding and shall be cladded with ss pipe frame on sides having cross section area 95mm x 25mm. the understructure shall consist of ss 202 grade loop leg having cross section area 95mm x 25mm. there shall be buffers provided to avoid to avoid scratches on the floor as well as uneven surfacing. the credenza unit shall have the size 1600mm x 500mm x 670mm. it should be made up of pre laminated particle board of grade ii of is 12823 with top 25mm thick, drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 7 drawer and operated with the assistance of ss handle and easily close & open with roller channel ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the credenza unit shall be mounted on ss 202 grade loop leg having cross sectional area 95mm x 25mm. pedestal shall be provided with an overall size 400mm x 500mm x 660mm. it should be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, facia shall be 18mm thick & drawer base shall be 9mm thick. it shall have 3 nos. of drawer having same size and operated with ss handle and easily close & open with the assistance of roller and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. the pedestal shall be mounted on injection moulded nylon castor.the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, issued by nabcb aaccredited labs, bifma membership and aiota certification. the oem should have green guard certification issued by ul for one or more products. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , table for reader and steno ( 4x2 ) providing & fixing executive table with an overall size 1200mm x 600mm x 750mm. the top shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca c frame with 0.9mm thick duly powder coated. the understructure shall consist of ms / crca rectangle pipe frame having cross section area 38mm x 25mm with 1.2mm thick. fixed top supporting pedestal shall be supplied at one side of the table. the pedestal shall be made up of 0.8mm thick high yield strength crca sheet of grade d confirming to is:513. it should have 3 nos. of drawer i.e. 2 box and 1 filing. it should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. the table shall be clad with modesty panel. it should be 18mm thick made up of pre laminated particle board.there shall be leveller provided at the bottom. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, issued by nabcb aaccredited labs, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , revolving chair ( officer ) providing & fixing ergonomically designed, comfortable & aesthetically appealing high back chair. the seat shall be made of 15mm thick hot pressed plywood with hr polyurethane foam 50mm thick having density 40kg / m³ upholstered with black leatherite tapestry with 0.8mm thick and 535 gsm and the back shall be supported by metal insert ms crca chrome plated with hr polyurethane foam 12mm thick having density 23kg / m³ upholstered with black leatherite with 0.8mm thick and 535 gsm.tthe armrest shall be used cushion arm completely joint with seat and back. the chair shall have synchro tilt revolving mechanism with single position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 120mm with bifma standard class 3 gaslift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 700 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 490±10 mm ( w ) x490±10 mm ( d ) and back size shall be 640±10 mm ( h ) from seat & overall height = 1095±10 mm. , chair for reader and steno providing & fixing revolving chair. the seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam having density 45kg / m³ and the back shall be padded with high resilience moulded polyurethane foam having density 40kg / m³. the same shall be upholstered with jute fabric tapestry 1mm thick and 300 gsm. the chair shall be supplied with polypropylene / abs seat and back cover for external support. the backrest of the chair shall be made by keeping the natural curvature of the spine. the armrest shall be used black integral polypropylene arm completely joint with seat. for seating durability the chair shall have push back 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged injection moulded 30% glass filled black nylon having pitch circle dia. 650 mm fitted with 5 nos. twin wheel castors. the castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 430±10 mm ( d ) x 460±10 mm ( w ) and back size shall be 415±10 mm ( w ) x 400±10 mm ( ht ) from seat. overall height shall be = 920±10 mm, base width / depth = 710±10 mm. , almirah for reader & judgement writer ( 915 x 485 x 1980 ) providing & fixing steel almirah in perfectly upright and straight position. the overall size of the almirah shall be 915mm ( w ) x 485mm ( d ) x 1980mm ( h ) including legs. it should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. stiffeners shall be provided in shelf & door. the steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 40kg maximum. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50 60?. , book rack 4dr book case ( w915 x d320 x h1750 ) providing & fixing metal book case with an overall size 915 mm ( w ) x 320 mm ( d ) x 1750mm ( h ) . the book case shall be supplied with 4 nos. of individual compartments. top, back & side panels shall be made of 0.8mm and rest 1mm high yield strength crca sheet of grade ‘d’ confirming to is: 513. each door shall have individual locking provision and 4 mm thick transparent glass for clear inside vision secured in a metal frame through rubber gasket. each door shall have scissor mechanism for receding inside the top of respective compartment which ensures parallel & smooth movement. each door shall have plastic side end caps as handle which is easy to grip. each compartment has a storage shelf having uniformly distributed load capacity of each shelf is 40 kg maximum. the finish is epoxy polyester powder coated to the thickness of 40 60?. adjustable leveler shall be provided with metal insert to resist scratches on the floor and also level & support structure. , table for advocates ( w1500 x d750 x h750 ) providing & fixing modular table in completely knock down conditions with an overall size 1500mm x 750mm x 750mm that is to be assembled at site. the construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. the worktop shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. the top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. a pullout keyboard trey shall be provided of 18mm thick pre laminated particle board having size 550mm x 280mm. the trey shall be operated on keyboard channel. the top shall be supported over particle board base gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. it should be 18mm thick pre laminated particle board with appropriate pvc edge banding connected with both end. there shall be buffers provided at the base to avoid scratches on the floor. a mobile pedestal shall be provided with an overall size 400mm x 450mm x 650mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the pedestal shall be mounted over 50mm injection moulded nylon castor. a movable type cpu unit shall be provided with an overall size 468mm x 284mm. the cpu unit shall be made up of 18mm thick pre laminated particle board. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, issued by nabcb aaccredited labs, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , chairs for advocates gb 406 providing & fixing visitor chair with ergonomic design for user comfort. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg / m³ in seat and 40mm thick having density 40kg / m³ in back. the same shall be upholstered with tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be used of black integral polyurethane arm with metal insert completely joint with seat and back. the frame structure shall be cantilever support type made up of ms / crca powder coated round pipe of dia. 25.4mm with 2mm thick. there shall be co polymer polypropylene shoe provided at the base to avoid scratches on the floor. the seat size shall be 460±10 mm ( w ) x 450±10 mm ( d ) and back size shall be 460±10 mm ( w ) x 400±10 mm ( h ) from seat. seat height = 450±10 mm, overall height shall be = 830±10 mm, overall width 555±10 mm, overall depth = 595±10 mm. , benches for munshi of advocates ( w1200 x d600 x h750 providing & fixing executive table with an overall size 1200mm x 600mm x 750mm. the top shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca c frame with 0.9mm thick duly powder coated. the understructure shall consist of ms / crca rectangle pipe frame having cross section area 38mm x 25mm with 1.2mm thick. fixed top supporting pedestal shall be supplied at one side of the table. the pedestal shall be made up of 0.8mm thick high yield strength crca sheet of grade d confirming to is:513. it should have 3 nos. of drawer i.e. 2 box and 1 filing. it should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. the table shall be clad with modesty panel.the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , table for peons ( w1200 x d600 x h750 ) providing & fixing executive table in knock down condition with an overall size 1200mm x 600mm x 750mm that is to be assembled at site. the worktop shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on ms / crca rectangle pipe frame having cross section area 40mm x 20mm with 1.6mm thick. the table understructure shall be supplied with ms round pipe having dia. 25.4mm with 1.6mm thick. 1 nos. footstep shall be provided between both side leg with the same size i.e dia. 25.4mm with 1.6mm thick. fixed pedestal unit shall be supplied with 3 nos. of drawer at one side. all the drawer shall be synchronized locked with central locking mechanism by one single key. the drawer shall be operated with recessed handle. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, issued by nabcb aaccredited labs, bifma membership and aiota certification.the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , table top 600x450 mm providing & fixing wooden laptop stand table top desk organizer for writing / sketching stand, wooden desk organizer ( brown, big size 600x450 mm ) . portable, adjustable, foldable.uses for office purpose, it maintains privacy, reduces strain on eyes, helpful in no cervical pain, improves handwriting, when you do work on it your work efficiency increases. , judgement writer room , computer table ( 4 x 2 ) providing & fixing executive table with an overall size 1200mm x 600mm x 750mm. the top shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca c frame with 0.9mm thick duly powder coated. the understructure shall consist of ms / crca rectangle pipe frame having cross section area 38mm x 25mm with 1.2mm thick. fixed top supporting pedestal shall be supplied at one side of the table. the pedestal shall be made up of 0.8mm thick high yield strength crca sheet of grade d confirming to is:513. it should have 3 nos. of drawer i.e. 2 box and 1 filing. it should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. the table shall be clad with modesty panel.the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , computer chair providing & fixing high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg / m³ in seat and 40mm thick having density 32kg / m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be used black integral polypropylene arm completely joint with seat. for seating durability the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 120mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700mm and fitted with 5 nos. twin wheel castors. the castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycle with 250lbs load. the seat size shall be 465±10 mm ( w ) x 460±10 mm ( d ) and back size shall be 480±10 mm ( w ) x 625±10 mm ( h ) from seat & overall height = 1060±10 mm. , ahlmad room , table ( 1200 x 600 ) providing & fixing executive table in knock down condition with an overall size 1200mm x 600mm x 750mm that is to be assembled at site. the worktop shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on ms / crca rectangle pipe frame having cross section area 40mm x 20mm with 1.6mm thick. the table understructure shall be supplied with ms round pipe having dia. 25.4mm with 1.6mm thick. 1 nos. footstep shall be provided between both side leg with the same size i.e dia. 25.4mm with 1.6mm thick. fixed pedestal unit shall be supplied with 3 nos. of drawer at one side. all the drawer shall be synchronized locked with central locking mechanism by one single key. the drawer shall be operated with recessed handle. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, issued by nabcb aaccredited labs, bifma membership and aiota certification.the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , chairs providing & fixing visitor chair with ergonomic design for user comfort. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg / m³ in seat and 40mm thick having density 40kg / m³ in back. the same shall be upholstered with tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be used of black integral polyurethane arm with metal insert completely joint with seat and back. the frame structure shall be cantilever support type made up of ms / crca powder coated round pipe of dia. 25.4mm with 2mm thick. there shall be co polymer polypropylene shoe provided at the base to avoid scratches on the floor. the seat size shall be 460±10 mm ( w ) x 450±10 mm ( d ) and back size shall be 460±10 mm ( w ) x 400±10 mm ( h ) from seat. seat height = 450±10 mm, overall height shall be = 830±10 mm, overall width 555±10 mm, overall depth = 595±10 mm. , almirah ( 915 x 485 x 1980 ) providing & fixing steel almirah in perfectly upright and straight position. the overall size of the almirah shall be 915mm ( w ) x 485mm ( d ) x 1980mm ( h ) including legs. it should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. stiffeners shall be provided in shelf & door. the steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 40kg maximum. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50 60?. , racks ( w900 x d450 x h1800 ) with 6 shelves providing & fixing a slotted angle rack with an overall size 900mm ( w ) x 450mm ( d ) x 1800mm ( h ) . the panel shall have 5 nos. of shelves made up of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. crca slotted angle shall be supplied with 2mm thick having size 40mm x 40mm. all steel components shall be 40 60? thick ( dft ) powder coated after 7 tank pre treatment process flow. corner plate ( gussets ) and fasteners shall be provided for complete assembly. , computer table 2 ( w1200 x d600 x h750 ) providing & fixing executive table with an overall size 1200mm x 600mm x 750mm. the top shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca c frame with 0.9mm thick duly powder coated. the understructure shall consist of ms / crca rectangle pipe frame having cross section area 38mm x 25mm with 1.2mm thick. fixed top supporting pedestal shall be supplied at one side of the table. the pedestal shall be made up of 0.8mm thick high yield strength crca sheet of grade d confirming to is:513. it should have 3 nos. of drawer i.e. 2 box and 1 filing. it should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. the table shall be clad with modesty panel.the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , computer chair providing & fixing high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg / m³ in seat and 40mm thick having density 32kg / m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be used black integral polypropylene arm completely joint with seat. for seating durability the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 120mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700mm and fitted with 5 nos. twin wheel castors. the castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycle with 250lbs load. the seat size shall be 465±10 mm ( w ) x 460±10 mm ( d ) and back size shall be 480±10 mm ( w ) x 625±10 mm ( h ) from seat & overall height = 1060±10 mm. , waiting hall , waiting area chair 3 seater ( size in mm 1750 ( l ) x 710 ( d ) x 755 ( h ) ) providing & fixing three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin.. the seat and back shall be upholestered with latherite tapestrythe armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? ( dft ) . there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm ( d ) x 405±10 mm ( h ) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , record room new , racks ( w900 x d450 x h1800 ) providing & fixing a slotted angle rack with an overall size 900mm ( w ) x 450mm ( d ) x 1800mm ( h ) . the panel shall have 5 nos. of shelves made up of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. crca slotted angle shall be supplied with 2mm thick having size 40mm x 40mm. all steel components shall be 40 60? thick ( dft ) powder coated after 7 tank pre treatment process flow. corner plate ( gussets ) and fasteners shall be provided for complete assembly. , tables ( w1200 x d600 x h750 ) providing & fixing executive table with an overall size 1200mm x 600mm x 750mm. the top shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca c frame with 0.9mm thick duly powder coated. the understructure shall consist of ms / crca rectangle pipe frame having cross section area 38mm x 25mm with 1.2mm thick. fixed top supporting pedestal shall be supplied at one side of the table. the pedestal shall be made up of 0.8mm thick high yield strength crca sheet of grade d confirming to is:513. it should have 3 nos. of drawer i.e. 2 box and 1 filing. it should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. the table shall be clad with modesty panel.the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , chairs providing & fixing revolving chair. the seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam having density 45kg / m³ and the back shall be padded with high resilience moulded polyurethane foam having density 40kg / m³. the same shall be upholstered with jute fabric tapestry 1mm thick and 300 gsm. the chair shall be supplied with polypropylene / abs seat and back cover for external support. the backrest of the chair shall be made by keeping the natural curvature of the spine. the armrest shall be used black integral polypropylene arm completely joint with seat. for seating durability the chair shall have push back 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged injection moulded 30% glass filled black nylon having pitch circle dia. 650 mm fitted with 5 nos. twin wheel castors. the castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 430±10 mm ( d ) x 460±10 mm ( w ) and back size shall be 415±10 mm ( w ) x 400±10 mm ( ht ) from seat. overall height shall be = 920±10 mm, base width / depth = 710±10 mm. , almirah ( 915 x 485 x 1980 ) providing & fixing steel almirah in perfectly upright and straight position. the overall size of the almirah shall be 915mm ( w ) x 485mm ( d ) x 1980mm ( h ) including legs. it should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. stiffeners shall be provided in shelf & door. the steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 40kg maximum. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50 60?. , server room new , tables ( 1200 x 600 ) providing & fixing executive table with an overall size 1200mm x 600mm x 750mm. the top shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca c frame with 0.9mm thick duly powder coated. the understructure shall consist of ms / crca rectangle pipe frame having cross section area 38mm x 25mm with 1.2mm thick. fixed top supporting pedestal shall be supplied at one side of the table. the pedestal shall be made up of 0.8mm thick high yield strength crca sheet of grade d confirming to is:513. it should have 3 nos. of drawer i.e. 2 box and 1 filing. it should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. the table shall be clad with modesty panel.the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , chairs providing & fixing visitor chair with ergonomic design for user comfort. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg / m³ in seat and 40mm thick having density 40kg / m³ in back. the same shall be upholstered with tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be used of black integral polyurethane arm with metal insert completely joint with seat and back. the frame structure shall be cantilever support type made up of ms / crca powder coated round pipe of dia. 25.4mm with 2mm thick. there shall be co polymer polypropylene shoe provided at the base to avoid scratches on the floor. the seat size shall be 460±10 mm ( w ) x 450±10 mm ( d ) and back size shall be 460±10 mm ( w ) x 400±10 mm ( h ) from seat. seat height = 450±10 mm, overall height shall be = 830±10 mm, overall width 555±10 mm, overall depth = 595±10 mm. , providing & fixing curtain set for windows and door with rod and fitting complete for retiring room, court room, judgement writer room, ahlamd room, record room & server room....

Rail Coach Factory - Punjab

38964369 supply of ball bearings : 6319 / c3 ( both side open ) , brand: skf, fag, nbc only. [ warranty period: 30 months after the date of delivery ] , ball bearing: 6318 / c3, brand: skf, fag, nbc only. [ warranty period: 30 months after the date of delivery ] => limited...

Punjab Police Housing Corporation Limited - Punjab

38872109 supply, installation, testing and commissioning of corrugated sheet unit at central jail, ludhiana. , single face high speed corrugation machine ( oblique type ) ball bearing model. , 1. speed 110 feet / min with one set narrow flute rolls self loading reel stand. 2. three heaters. 3. two pre heaters complete with variable speed drive controller for motor, pulley and belts size 52”. 4. with tested en 19 forged rolls. 5. with variable speed drive control panel. 6. with specially graded casting pressure roll. , reel to sheet cutter type size 52” complete with all usual accessories. , 1. length of cut change with changing gears. 2. with ac drive control panel for speed , sheet pasting machine adjustable complete with motor pulley and belt of size 85 , four bar rotary cutting and creasing machine size 85” , 1. 4 sets of cutting. 2. 4 set of creasing dies complete with motor, pulley and belts. , eccentric slotter size 85” , 1. 3 slotting and 1 corner cutting dies complete with electric motor. 2. slot depth 18”. 3. slotting knife thickness 6mm. , double colour long way flexo sheet printer. , 1. size 52” x 90” with variable speed dc drives motor & controller and all usual accessories. 2. frequently drive panel. 3. suitable for printing paper. , box stitching machine ( vickers type ) power operated ( angular or straight ) : size 42...

Rail Coach Factory - Punjab

38863168 supply of spare parts required for maintenance of godrej fork lift trucks cap.3 ton & 5 ton., runner 3 ton gear conforming to part no. mh38700057 / 25173813pa00660 of m / s godrej for flt 3 ton [ warranty period: 30 months after the date of delivery ] , automatic drain valve assy for godrej fork lift truck conforming to part no. mh02099761 of m / s. godrej & boyce [ warranty period: 30 months after the date of delivery ] , t. q. hose for godrej fork lift truck. conforming to part no. mh39552986 / 40142020sd00141 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] , hyd. hose tank to pump for godrej fork lift truck cap 5 ton. conforming to part no. mh39550169 / 40142020sd00291 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] page 1 of 5 run date / time: 27 / 07 / 2023 13:47:30stores / hsq / rcf tender document , walvoil valve ( no2r30wdl ) / main valve for godrej flts. conforming to part no. mh39100160 / 40141608sd00038 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] , ball bearing for godrej fork lift trucks. conforming to part no. mh38700170 / 25173813pa00703 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] , hub f.c. s4 engine for godrej fork lift trucks. conforming to part no. mh38700059 / 25173813pa00760 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] , gear washer for godrej fork lift trucks cap 03 ton . conforming to part no. mh38700194 / 25173813pa00719 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] , transmission nut for godrej fork lift trucks cap. 3 ton. conforming to part no. mh38700193 / 25173813pa00718 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] , t.q. hose transmission to radiator. for godrej fork lift trucks. conforming to part no. mh39550744 / 40142020sd00210 of m / s. godrej. [ warranty period: 30 months after the date of delivery ] ...

Indian Army - Punjab

38809456 bids are invited for boq bid nk001637 4 8 volt bty , nk002714 bty 6v 4 5 ah , nk001135 4 way connector , nk0014 ball bearing , nk002329 b p cuff , nk001036 rechargeable bty , nk001040 capacitor total quantity : 10...