Department of Cooperation - Punjab

37793906 tender for fabrication and erection work 2 dismantling of ms / gi / ss pipe line size 1 / 2 to 12 erection of ms / gi / ss pipe line size 1 / 2 to 12 3 dismantling ofms / ss pipe line size 14 to 50fabrication ofms / ss pipe line size 14 to 50 3mm / 6mm / 8mm / 10mm / 12mmerection of faricated ms / ss pipe line size 14 to 50 4 dismantling of c i pipe line upto 12erection of c i pipe line upto 12 5 dismentalling of ms / ss nipple upto 12dia and upto 1 meter longfabrication of ms / ss nipple upto 12dia and upto 1 meter longerection of ms / ss nipple nipple upto 12dia and upto 1 meter long 6 dismentalling of faricated ms / gi / ss nipple size 14to 50and upto 1 meter longfabrication ofms / gi / ss nipple size 14 to 50 and upto 1 meter longerection of faricated ms / gi / ss nipple size 14 to 50 and upto 1 meter long 7 dismentalling of ms / ss bend upto 12dia fabrication of ms / s bend upto 12dia erection of ms / ss bend upto 12dia 8 dismentalling of ms / gi / ss bend size 14to 50fabrication ofms / gi / ss bend size 14 to 50 erection of faricated ms / gi / ss bend size 14 to 50 9 dismentalling of ms / ss cone size upto 100fabrication of ms / ss cone size upto 100 erection of ms / ss cone size upto 100 10 dismentalling of c i bend upto 12erection of c i bend upto 12 11 dismantling of c i tee upto 12erection ofc i tee upto 12 12 dismantling of c i cross upto 12erection ofc i cross upto 12 13 dismantling of ms / ss tee size upto 100fabrication of ms / ss tee size upto 100 erection of ms / ss tee size upto 100 14 dismantling of ms / ss crosssize upto 100fabrication of ms / ss cross size upto 100 erection of ms / ss cross size upto 100 15 dismantling of railing of pipe. fabrication of railing pipe erection of railing pipe 16 fixing of g.i wire weaved fencing around cold water reservoir 17 dismantling and washing of old flange 18 fabrication and drilling of flange from ms plate 19 replacement of square bar / rail 40mm / 50mm 20 replacement of runner flat of cane carrier / secondary cane carrier / irc / bagasse elevator / mbc / rbc 65mm / 75mm 21 replacement of angle of cane carrier / secondary cane carrier / irc / bagasse elevator / mbc / rbc 65mm / 75mm / 90mm 22 replacement of side plate of cane carrier / secondary cane carrier / irc / bagasseelevator / mbc / rbc chains6mm / 8mm 23 dis.fab. and erection of hood of cane leveller / cane chopper with supporting angle 10mm / 12mm 24 dis.fab. and erection of both side plate of hood of cane leveller / cane chopper with supporting angle 10mm / 12mm 25 dis.fab. and erection of both side plate ( ms / ss 10mm / 12mm ) of fibrizer with supporting angle 26 dis.fab. and erection of front side plate ( ms / ss 10mm / 12mm ) of fibrizer with supporting angle 27 dis. fab. and erection of roundtrough of secondary cane carrier / irc / bgasse elevator / mbc / rbc 8mm / 10mm / 12mm plate 28 dis. fab. and erection of base plate ( ms / ss 8mm / 10mm / 12mm ) of secondary cane carrier / irc / bagasse elevator / mbc / rbc 29 fabrication of rakesof secondary cane carrier / irc with attachmentfrom ms pipe size 4 and 1 30 fabrication of rakes of bagasse elevator / mbcwith attachmentfrom ms pipe size 3 and 1 31 dismentalling of ms / ss round / square tankfabrication of ms / ss round / square tankerectionof ms / ss round / square tank 32 dismentalling bagacilo screen framefabrication bagacilo screen frameerectiontion bagacilo screen frame 33 dismentallingbagacilo railing framefabricationbagacilo railing frame erectiontionbagacilo railing frame 34 dismentalling of ci / gm sluice / angle / butterfly valve size upto 16erection of ci / gm sluice / angle / butterfly valve size upto 16 35 dismentalling of pan discharge butterfly valveerection of pan discharge butterfly valve 36 dismentalling of ss / brass tube of evaporators ( s.k, v.c, quads ) fitting of ss / brass tube of evaporators ( s.k, v.c, quads ) 37 dismentalling of ss / brass tube of pansfitting of ss / brass tube of pans 38 dismentalling of ss / brass tube of juice heatersfitting of ss / brass tube of juice heaters 39 ms straight / right angle valve size 300mm, 350mm, 400mm, 450mm, 600mm, 700mm, 900mm and 1000mmdis.erection 40 hydaulic testing of evaporators ( s.k, v.c, quads ) hydaulic testing of panshydaulic testing of juice heaters 41 ms blindsize 1 to 50dis.fab.erection 42 dismentalling of gi / colored coated sheetfitting of gi / colored coated sheet 43 dismentalling of acc sheetfitting of acc sheet 44 dismentalling of ms / ss reducer size upto 100fabrication of ms / ss reducer size upto 100 erection of ms / ss reducer size upto 100 45 dismentalling of staircasingfabrication of staircasingerection of staircasing 46 dismentalling of monkey ladderfabrication of monkey laddererection ofmonkey ladder 47 dismentalling of fabricated frame of pump & motorfabrication of frame of pump & motorerection of frame of pump & motor 48 dismentalling of juice / water / syrup / molasses pumperection of juice / water / syrup / molasses pump 49 dismentalling of injection / spray / massicuite / magma pumperection of injection / spray / massicuite / magma pump 50 dismentalling of motor upto 50hperectionof motor up to 50hp 51 dismentalling of motor 55 hp to 250 hperectionof motor 55 hp to 250 hp 52 dismentalling of bewelgeared discharge valve and fitting of butterfly valve with modification of nipple & flange 53 strengthening of building structure column binder 54 replacement of vljhdismantling & erection of vapour line juice heater.all dismantled connectionsto be connected. levelling &alignment to be made. 55 replacement of shell of pan 60 tondismantling fabrication& erection of pan shell.all dismantled connections to be connected. 56 replacement of save all of pandismantling & erection of save all of pan . all dismantled connections to be connected. 57 replacement of stirrer shaft of air cooled crystalizer a, b & c dismantling & erection of stirrer shaft of air cooled crystalizer a, b & c . all dismantled connections to be connected. dismantling & fitting of drive gear arrangement. 58 replacement of top cone of pandismantling & erection of top coneof pan . all dismantled connections to be connected. 59 replacement of bottom cone of pandismantling & erection of bottom coneof pan . all dismantled connections to be connected. 60 replacement of cooling coils of vertical crystallizer as per drg. dismantling & erection of cooling coils of vertical crystallizer . all dismantled connections to be connected. 61 shifting of 50 tons capacity panfrom old mill to new milldismantling & erection of 50 tons capacity pan . all dismantled connections to be connected 62 shifting of vacuum crystallizer a in place of vaccum crystallizer c at the same floor dismantling & erection of vacuum crystallizer a in place of vaccum crystallizer c . all dismantled connections to be connected. 63 shifting of 50 ton air cooled crystallizer from old plant to new plantdismantling & erection of 50 ton air cooled crystallizer . all dismantled connections to be connected and drive arrangement 64 replacement of center shaft of juice clarifierdismantling , erection and alignment of center shaft of juice clarifier . all dismantled connections to be connected. 65 replacement of mud bootdismantling, fabrication & erection of mud boot. all dismantled connections to be connected. 66 replacement of compartment bottom plate of juice clarifier dismantling fabrication & erection of compartment plate 67 dismantlingofmassecuitegutter fabricationofmassecuitegutter erectionofmassecuitegutter 68 dismantling , fabrication & erection of dorr compartment shell with ms plate channel angles.the erection work for this will also include all connections which are dismantled during dismantling. 69 dismantling , fabrication & erection of dorr compartment / chamber roof with ms plate channel angles supports.the erection work for this job will also include all connections which are dismantled during dismantling. 70 dismantlingof top / bottom cover of juice heater erection of top & bottom cover 71 dismantling & erection ofsquare channel for rubber strip fitting ofjuice heaters 72 dismantling , fabrication and erection of compartment box of juice heater 73 dismantling of horizontal sugar melter and to be shifted as per the directions of ce / cc 74 shifting& erection of verticalsugar melter for reprocessing of moist sugar dismantling & erection of old vertical sugar melter for reprocessing of moist sugar. all dismantled connections to be connected with drive arrangement 75 cantilever provided at the top of o.c.filter to lift the drum at the height appx 10.0 meter from ground floor. 76 dismantling of old mud mixer scroll fabrication and erection of newmud mixerscroll 77 modification of mud mixer trough to increase the length of mud mixer trough by approx. 1 mtr. 78 replacement ofbagacilo line dismantling, fabrication and erection of bagacilo line 79 dismantling, fabrication and erection of bagacilo cyclone 80 ms new sulphur furnace ( complete ) fabrication & erection of sulphur furnace as per drg. / as per instructions of ce / cc 81 fabrication & erection of ms shoot for dsm screen 82 fabrication , erection of corrugated 6. / 8 inch wide plate for equal water distributing at etp 83 dismantle, fabrication and erection of sperger m.s. pipe having length 500mm app, dia 14.0 inch dia 84 dismantling, fabrication and erection of worn out stirrer arm of vertical crystallizers drive. 85 replacement of distance piece of vapour pipe upto 1.5 mtr 86 sulphur furnace ( extra work ) scope of worka. topbaffle plate to be dismantle and erected 250 mm away from existing site.b. dismantling of existing worn outbaffle plate , fabricate and erect at existing site 87 gate frame of magma mixturescope of worka. fabricationof frame along with ms channel.b. drill to be made in both ms channel.c. erection of frame at site 88 fabrication and erection of sulphur furnace heating element coil of sulphur furnace melter.a fabrication of nipples and erection at sulphur melter systemsb fabrication of nipples and erection of sulphur melter receiver 89 shifting of sugar hopper fromold plant to new plantdismantling & erection of sugar hopper. 90 erection & commissioning of hopper tray with decking plate, connection arrangementof connecting rod and angle klits for wooden strips fitting approx. length 10 mtr. 91 dismantling, shifting and erection of sugar elevator from old plant to new plant complete with structure 92 dismantling, shifting and erection of sugar graderfrom old plant to new plant complete with structure 93 planetary gear boxerection & commissioningof planetary gear box at vertical crystallizerany additional job to complete theerection work of planetary gear boxto be carried out by the contractor 94 fabrication & erection of pneumatic shoot of grader 95 erection of pneumatic clamps of grader 96 repair of stirrer shaft of vacuum crystallizer dismantling & erection of stirrer shaft of vacuum crystallizer after repair 97 strengtheningof stirrer shaft of air cooled crystallizer• dismantling & erection of stirrer shaft of air cooled crystallizer after repair. 98 dismantling of platform fabrication of platform erection of platform 99 fabrication and erection of cane unloader bridge platform 100 dis, feb, & errection of umbrella of pan along with its supports. 101 dismantling of j pipe of pans fabrication of j pipe of pans erection of j pipe of pans 102 dismantling of vapour / exhaust pipe size 700mm / 900mm / 1000mm / 1100mm fabrication of vapour / exhaust pipefrom 8mm / 10mm thick plate erection of vapour / exhaust pipe 103 dismantling of structure as per the instruction of ce fabricationof structure erection ofstructure 104 patch work of different equipments 105 to straight the old damaged vapour pipe and round tank for platform. 106 dismantling of steam coil of molasses storage tank at pan station size 1” to 2”. fabricationof steam coil of molasses storage tank at pan station size 1” to 2”. erection of steam coil of molasses storage tank at pan station size 1” to 2”. 107 dis, fab, & errection of juice coil of juice clarifier size 4”, 5” & 6” alongwith its nipple 108 dis. fab & erection of wt. juice pump strainer 109 dismantling, fabrication and erection of pan save all top plate 110 planetary gear boxerection of planetary gear box ofhorizontalcrystallizer 111 replacement of old gate valve with new gate valve of crystallizers 112 dismantling of double beat valve and erection of same of juice heater at existing site. 113 dismantling of old transient heater and erection of new transient heater along with all connections and valve. 114 fabrication & erection of factory structure complete window ( frame & grills ) 115 modification, & erection of mill house rotary screen inlet juice tank &platform 116 fabrication and erection of excess bagasse carrier to rbc as per the dirction of ce scope of work ( a ) fabrication and erection of column and structure for belt conveyor , along with drive system and discharge chute to rbc column and steel structure 117 fabrication and erection of cooling tower structure and shed 118 strengthening of pans / vacuum crystallizershell with angle and channels in round shape with ms angle 75mmx75mm and dia 4mtr ( two rounds ) 119 strengthening of evaporator shell with angle and channels in round shape with ms angle 75mmx75mm and dia 2.80mtr ( two rounds ) 120 dismantling , fabrication & erection of juice feed boxes of juice heater double beat valve.the erection work for this job will also include all connections which are dismantled during dismantling. 121 dismantling , fabrication & erection of melter of sulphur furnace as per existing design. this work include dismantling and erection of all connections, man hole, flanges etc. 122 dismantling , fabrication & erection of scrubber of sulphur furnace as per existing design. this work include dismantling and erection of all connections, man hole, flanges etc. 123 replacement of sealing ring of dorr mud boot 124 dismantling , fabrication & erection of worn out heavy / light vacuum tank of rvf including all connections. 125 dismantling , fabrication & erection of ms barometric condenser of rvf. this job will include all connections which are dismantled during dismantling. 126 dismantling , fabrication & erection of bottom trough of rvf 127 dismantling , fabrication & erection of down take of pan from 10 / 12 plate 128 dismantling , fabrication & erection distributor of pans 129 replacement of feed box of pans including all connections 130 fitting of pad, ribbes on shaft of air cooled crystlizer / vaccum crystlizer and fitting of angle and ribben...

Military Engineer Services - Punjab

37274515 repair and replacement of plastering, flooring, joinery, connected b / r items and periodical services to otm accn in new cantt zone ‘a’ at mil stn patiala under ge ( south ) patiala. 1 taking down chowkhats or frames (wooden joineries with wooden or steel chowkats) complete with shutters (without taking off shutters from the frames) exc 1.5 sqm butnot exc 4.00 sqm each and removing from site or to store as complete all as specified and directed by engineer in charge. 2 taking down chowkhats or frames(wooden joineries with wooden or steel chowkats) complete with shutters (without taking off shutters from the frames) notexc 1.5 sqm each and removing from site or to storecomplete all as specified and directed by engineer in charge. 3 taking down wooden shutters of any description exc 1.00 sqm but not exc 2.00 sqm each and removing from site or to storecomplete all as specified and directed by engineer in charge. 4 s &f pressed steel framed made out of 1.25mm thick ms sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc,complete all as specified and directed by engineer in charge. 5 description all as per serial item no 4 here in before but size 105 x 60mmcomplete all as specified and directed by engineer in charge. 6 m&l for cement concrete 1:2:4 type b 0 using 12.5 mm graded crushed stone aggregate as in mass concrete or filling backs of chowkats complete all as specified andcomplete all as specified and directed by engineer in charge. 7 s&f factory made flush shutters 35mm thick minimum 5 ply, solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm thick lipping frame to match including supply and fixing following itemscomplete all as specified and directed by engineer in charge:(a) stainless steel (304 grade) finished butt hinges 100mm 4 nos per leaf(b) stainless steel (304 grade) finished tower bolt 150mm long 2 nos per leaf(c) stainless steel (304 grade) finished handles 150 mm 2 nos per leaf(d) stainless steel (304 grade) finished sliding door bolt/aldrop 16 x 300mm 1 no per leaf(e) stainless steel (304 grade) finished floor door stooper 1 no per leaf 8 s&f 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in ssr 91 pt 1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 grade wire cloth (wire dia. 0.36mm) and supply and fixing the following itemscomplete all as specified and directed by engineer in charge.:(a) stainless steel (304 grade) finished butt hinges 100mm 3 nos per leaf(b) stainless steel (304 grade) finished tower bolt 150mm long 2 nos per leaf(c) stainless steel (304 grade) finished handles 150 mm 2 nos per leaf(d) stainless steel (304 grade) finished sliding door bolt/aldrop 16x300mm 1 no per leaf 9 providing and fixing factory made extruded aluminium casement windows (with provision for cooler) with 50 micron powder coating doubled panelled anddouble shutters consisting of frame and mullion of 101.60x44.45x1.29 mm and shutters made of 63.5x31.75x1.29mm and to be fixed with and including epdm gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed incomplete all as specified and directed by engineer in charge including supply and fixing following items : (a) stainless steel (304 grade) finished butt hinges 100mm 2 nos per leaf.(b) powder coated aluminium tower bolt 150mm long 2 nos per leaf.(c) powder coated aluminium handles 150 mm 1 nos per leaf. 10 s & f anodised aluminium window and ventilator shutters fixed type without sash bar,powder coating of any colour ( thickness of powder not less than 50 microns). aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc.complete all as specified and directed by engineer in charge. 11 powder coated 50 microns extruded aluminium glazing doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3x44.45x1.29mm for top rails and bottom rails and including 12mm thick high density fibre board pre laminated on both sides (water proof) below & above middle/lock rail and to be fixed with and including epdm gasket to render the glazing, air and water tight etc. and aluminium beads 20mm sizecomplete all as specified and directed by engineer in charge.including supply and fixing the following items:(a) stainless steel (304 grade) finished butt hinges 100mm 3 nos per leaf.(b) powder coated aluminium tower bolt 150mm long 2 nos per leaf(c) powder coated aluminium handles 150 mm 2 nos per leaf 12 s & f in repair aluminium tower bolt 200mm longaddand fixedcomplete all as specified and directed by engineer in charge. 13 s & f in repair aluminium alloy, anodised, sliding door bolt 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by engineer in charge. 14 s & f in repair mild steel butt hinges of size 100mm medium weight cold rolledcomplete all as specified and directed by engineer in charge. 15 s & f in repair floor door stopper 150 mm long of aluminium alloy body and toungue anodised with hard drawn steel springfixedin floorscomplete all as specified and directed by engineer in charge. 16 s & f in repairaluminium handles of size 150mm ovaltypecasttype anodisedcomplete all as specified and directed by engineer in charge. 17 framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conformint to fe 410 w complete all as specified and directed by engineer in charge. 18 s & f factory made solid panel pvc door shutters 30 mm thick (style) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing s& f complete all as specified and directed by engineer in charge. 19 s & f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by engineer in charge. 20 s & f 100 mm size pvc butt hingescomplete all as specified and directed by engineer in charge. 21 s & f 125 mm pvc handlescomplete all as specified and directed by engineer in charge. 22 s & f200 mm long pvc tower boltcomplete all as specified and directed by engineer in charge. 23 m & l for preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primercomplete all as specified and directed by engineer in charge. 24 m & l for preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cmand applying two coats of synthetic enamel paintcomplete all as specified and directed by engineer in charge. 25 factory made steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8mm square bars, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing no. td 219(c) sheet 1/3 to 3/3complete all as specified and directed by engineer in charge and as approved by genote: (i) for the purpose of measurement & payment double shutter with frame shall be considered as one unit. (ii) unit rate quoted against this item shall also include the iron mongery and grill as shown on drgs.(iii) glazing, wire mesh & painting shall be measured & paid for separately. 26 taking down old unserviceable wire cloth any size from wooden/ metal framescomplete all as specified and directed by engineer in charge. 27 s & f galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples incl replacement of second class wooden beading where ever reqdcomplete all as specified and directed by engineer in charge. 28 hacking out old broken glass (any thickness , size , quality or description) from wooden or metal frames glazed with oil putty or fixed with beads complete all as specified and directed by engineer in charge. 29 s & f sheet glass ordinary quality 4 mm thick not exe.0.50 sqm glazing with oil putty or fixed with wooden beads in squares any size of panecomplete all as specified and directed by engineer in charge. 30 description all as per serial item no 38 here in before but 4mm thick frosted glasscomplete all as specified and directed by engineer in charge. 31 s&f mild steel rat tail rod pattern helical door spring of size 300mm including roller and roller plate fixing to iron frame by weldingcomplete all as specified and directed by engineer in charge. 32 demolition of cement concrete un reinforced in ground floors and pavingsnexec 150 cm thick (above or below ground level) complete all as specified and directed by engineer in charge. 33 demolition of re inforced cement concrete of any description and in any position incl cutting of re inforcement to facilitate demolition where everreqd complete all as specified and directed by engineer in charge. 34 m & l for machine cut mirror polished kota stone 20mm 25mm thick slab as in cooking platforms/ landings, treads and risers of stairs and stepslaid over and includingscreed bed or 15mm th bedding layer in cement mortar 1:3 as base laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing, polishingcomplete all as specified and directed by engineer in charge. 35 m & l for machine cut mirror polished kota stone slab flooring 20mm 25mmthick laid over and including 20mmscreed bedor bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing, polishingcomplete all as specified and directed by engineer in charge. 36 rounding to edges of stone slabs one edge , such as in steps, cooking plateforms & other similar situationscomplete all as specified and directed by engineer in charge. 37 dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by engineer in charge. 38 m & l for glazed ceramic coloured tiles in verticle surfaces joint free with glazed economy finish grade b ii (b) of size 300 x 600mm or bigger size7 mm thickas approved set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over 10 mm thick rendering in cement mortar in cm 1:3 for dado etc.,complete all as specified and directed by engineer in charge.note for skirting onlyskirtingmay be providedfrom the same tiles as being used in the floor of sameroomto match in lieu of economy finish tiles but nothing extra shall be admissible on this account. 39 m & l for non skid ceramic joint free tiles {non skidfinish/ matt superior finish grade b i or b ii (b) as approved}7 to 8 mm thick with rectified edges, (square/rectangular) area of each tile exceeding 0.11sqm and not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15 mm thick cement screedbed in cm 1:4complete all as specified and directed by engr in charge 40 m & l for vitrified ceramic tiles 8 9mm thick light colour (square/ rectangular) polished, area of each tile 600 x 600 mm , in floors etc. set and jointedin neat cement slurry and pointed in white or coloured cement to match the shade of tileover 15mm thick screed/ bedding layerin cm 1:4complete all as specified and directed by engineer in charge. 41 m & l for pcc 1:2:4 type b1 (using 12.5mm graded stone aggregate)25 mm thick to receive the floortiles complete all as specified and directed by engineer in charge. 42 taking down cementplaster or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed by engineer in charge. 43 m & l for rendering 15mm thick cement plaster in cement mortar 1:4 using wpcon fair faces of brick or concrete surfaces on walls etc., finishedeven and fairwithout using extra cement, complete all as specified and directed.note: supply only wpc shall be measured separately & paid for accordingly & shall beprovided @ 3% by weight of cement or as per manufacturers instructionscomplete all as specified and directed by engineer in charge. 44 supply only liquid waterproofing compound complete all as specified and directed by engineer in charge. 45 m & l for rendering 10 mm thick cement plaster in cement mortar 1:6 on fair faces of brick or concrete surfaces on walls etc., finishedeven and smooth without using extra cement,complete all as specified and directed by engineer in charge. 46 dubbing out average 15 mm thick in cement mortar 1:4 on irregular faces of walls, ceiling & chhajjas incl removing carefully old damaged loose concrete from rcc / pcc surfaces of ceiling/ chhajjas for double storey bldgscomplete all as specified and directed by engineer in charge. 47 m & l for rendering 10mm thick cement plasterin cm 1:3on concrete surfaces in ceiling/ chhajjas finished even and smooth without using extra cement complete all as specified and directed by engineer in charge. 48 preparation of new plastered or unplastered surfaces of walls etc.,and m & l for applying twocoat of distemper oil emulsion (obd) over a coat of chalk whiting (as primer)complete all as specified and directed by engineer in charge. 49 m & l for preparation of new plastered or unplastered surfaces of ceiling etc.,and applying three coat of lime white wash on ceiling surfacescomplete all as specified and directed by engineer in charge. 50 preparation of new plastered or unplastered surfaces of walls etc.,and m & l for applying twocoat of cement base paintover a coat of alkli resistance priming paint (as primer)complete all as specified and directed by engineer in charge. 51 m & l for pcc 1:2:4 type b1 (using 12.5mm graded stone aggregate) as in roof kerbs, pcc khurras, coping on parapet wall, mud stops, steps small sumps and like items slightly rounded or chamfered on the edgescomplete all as specified and directed by engineer in charge. 52 racking out joints , hacking for key incl removal of all grass, vegetation growth from roofs etc., andm & l for flush pointing to roof tiles/ terracing incement mortar 1:3complete all as specified and directed by engineer in charge. 53 demolition of brick work including all quains and arches pillars etc built in cement mortar or cement lime mortarcomplete all as specified and directed by engineer in charge. 54 m&l for brick work in cement mortar (1:6) using sub class b old size bricks staight or curved on plan exc 6.0 m mean raiduscomplete all as specified and directed by engineer in charge. 55 m & l 50mm thick pcc (1:3:6) type c2 (using 40mm grade aggregate) as in plinth protection, finishing the surfaces even & smooth w/o using extra cement complete all as specified and directed by engineer in charge. 56 s & f precast concrete interlocking paver block any shape and size & incl 25mm thick layer of sand cushion complete all as specified and as directed. confirming to is 15658 2006 of 60 mm thickness, m 35 gradecomplete all as specified and directed by engineer in charge. 57 dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by engineer in charge. 58 dismantling timber scantlings in framed work 40 sq. cm and over in section, in any position complete all as specified and directed by engineer in charge. 59 anodised aluminium snap grid frame work for false ceiling all as specified (size of grid 605 x 605mm) incl hangers 6 mm dia. g.i. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of g.i. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm longcomplete all as specified and directed by engineer in charge. 60 material & labourforgypsum board 600mmx 600mm x 12mm thick in ceiling fixedas per manufacturers instructions all as specified andcomplete all as specified and directed by engineer in charge. 61 s & f for hollowpvc wall liningconsisting of5mm thick wood grain printed pvc sheet inclusive of solvent cement and fixing at site on pvc frame as per specifications and drawing complete all as specified and directed by engineer in charge. 62 m & l for 5mm thick pvc sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make pvc frame as per specification and drawing complete all as specified and directed by engineer in charge. 63 s &f in repairpvc (swr) pipe110 mm bore rain water pipe single socketed in any length with rubber ring joints,fixed to wall complete all as specified and directed by engineer in charge. 64 complete removal of existing treatment of any type/description such as cement base paint, external emulsion etc from external surfaces of walls/rcc surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc with mechanical means/grindercomplete all as specified and directed by engineer in charge. 65 applying acrylic wall care putty in external walls/rcc surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving exterior paintingcomplete all as specified and directed by engineer in charge.notes : (i) the prepared surface after wall putty, the contractor will inform to the ge as well as to the engineer in charge for site inspection before applying further external finishes. please note that the further external finishes work will start only after approval of the prepared surface from the ge as well as to the engineer in charge through site order. 66 applying 02 coats of exterior emulsion paint (light shade) as per manufacture instructions by using roller to external walls/rcc surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed by engineer in charge. 67 writing letter of figures (block, roman italic or indian) n exc 30cm high complete all and the colour of paint and dimension of letter to be used as approved by engr in charge. 68 writing stops , commas, short lines, dashes, hypens, brackets etc and the colour of paint and dimension of letter to be used as approved by engr in charge. 69 m&l for cement plastering 5mm thick in(small patches) cemet mortar 1:3 as on ceilings or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed by engineer in charge. 70 complete removal of existing treatment of any type/description such as distempering work, internal emulsion etc from internal surfaces of walls & ceiling with mechanical means/grindercomplete all as specified and directed by engineer in charge. 71 applying acrylic thick wall care putty on internal surfaces of walls/ceilings (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior paintingcomplete all as specified and directed by engineer in charge.notes : (i) the prepared surface after wall putty, the contractor will inform to the ge as well as to the engineer in charge for site inspection before applying further external finishes. please note that the further external finishes work will start only after approval of the prepared surface from the ge as well as to the engineer in charge through site order. 72 applying 02 coats of interior emulsion paint (light shade) as per manufacture instruction by using roller to wall surfaces over & including a coat of interior wall primer as recommanded for under coat by manufacturer of interior emulsion by using following brands of emulsion and primercomplete all as specified and directed by engineer in charge. 73 m&l for preparing existing old treated surface of external walls/rcc surfaces/soffits of chajjas/roof projection/centilevers/balcony etc incl cornices and applying one coat of cement base paint @5sqm/kg/1 coat by usingof cement based paint by rollercomplete all as specified and directed by engineer in charge. 74 m&l for preparing existing old treated surface of external walls/rcc surfaces/soffits of chajjas/roof projection/centilevers/balcony etc incl cornices and applying two coat of cement base paint @5sqm/kg/1 coat by usingof cement based paint by rollercomplete all as specified and directed by engineer in charge. 75 m& l for prepration of old plastered surface/unplastered surfaces including washing, rubbing down and stoping of distempered and painted surfaces and applying two coat of oil bund distemper on wallcomplete all as specified and directed by engineer in charge. 76 m& l for prepration of old plastered surface/unplastered surfaces including washing, rubbing down and stoping of distempered and painted surfaces and applying one coat of oil bound distemper on wallcomplete all as specified and directed by engineer in charge. 77 m & l for preparing existing treated surfaces on wall including cornices and applying one coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. this shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. about 1.3 kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by engineer in charge. 78 m & l for preparing existing treated surfaces on wall including cornices and applying two coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. this shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. about 1.3 kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by engineer in charge. 79 m & l for preparing existing treated surfaces on ceiling including cornices and applying one coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. this shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. about 1.3 kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by engineer in charge. 80 m & l for preparing existing treated surfaces on ceiling including cornices and applying two coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. this shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. about 1.3 kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by engineer in charge. 81 m & l for preparing old painted steel and iron surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by engr in charge. 82 m & l for preparing old painted wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by engr in charge. ...

Military Engineer Services - Punjab

37257839 welcome maint to offrs md accn in site 3 & 4 under age b / r i ofge ( west ) ferozepur cantt. 1 demolition of brick work built in cement mortar of any specification and in any position complete all as specified. 2 m&l brick work in cement mortar 1:6 using sub class ‘b’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified. 3 all as per item no. 02 here in before but using old bricks retrieved from item no :1 demolitionincluding cleaning and removal of mortar from old bricks. 4 m & l brick work with sub class b bricks straight or curved on plan to any radius in half brick thick wall built in cm 1:4 complete all as specified and directed. 5 dismantling of floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles and rubbish off the premises. 6 m & l for non skid coloured ceramic tiles of7 to 8 mm thick, area of each tile exceeding 0.06 sq m but not exceeding 0.11sq min floors set and jointed in neat cement slurry and pointed in white cementmixed with colour pigment to match over a screed layer of 15 mm thick in cm 1:6 complete all as specified and as directed. 7 m & l for non skid coloured ceramic tiles of7 to 8 mm thick, area of each tile exceeding 0.11 sq m but not exceeding 0.18sq min floors set and jointed in neat cement slurry and pointed in white cementmixed with colour pigment to match over a screed layer of 15 mm thick in cm 1:6 complete all as specified and as directed. 8 m & l for non skid coloured ceramic tiles of7 to 8 mm thick, area of each tile exceeding 0.11 sq m but not exceeding 0.18sq m as in skerting / dadoset and jointed in neat cement slurry and pointed in white cementmixed with colour pigment to match andbacking with 10 mm thick in cm 1:4 complete all as specified and as directed. 9 m&lof glazed coloured and cereamic tiles in vertical surfaces450x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over backing coat 10mm thick in cement mortar 1:4 for laying skirting dados and vertical surfaces all as complete all as specified and directed. 10 m & l green marble slab, 16 18mm thick of size not less than 1 sqm each, machine cut as cooking platform or in any position, set and bedded in gray cement slurry over & including 15mm thick screed in cement mortar ( 1:4 ) and pointed in white cement with admixture of pigment to match the shade of marbleincluding cutting, polishing ( mirror type ) complete all as specified and directed. 11 m & l granite ( of any type ) tiles 16 20mm thick machine cut, bedded andjointed with grey cement slurryand pointed with white cementwith admixture of pigment to match the shade of granite stone including grinding and polishing with 15mm thick screed in cement mortar ( 1:4 ) complete all as specified and directed. 12 m & l vitrified ceramic tiles 10mm thick ( square / rectangular ) polished area of each tiles exc 0.36sqm and not exceeding 0.42sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured ( dark shade ) cement to matchover 20 mm thick screed bed or bedding layer of cement mortar ( 1:6 ) for laying floor finishes complete all as specified and directed. 13 m&l forlight shade vitrified tile 10mm thick polished, area of tile n exc.0.36 sqm as in skirting set and jointed in cement slurry over and including 15mm thick screed in cement mortar ( 1:4 ) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. 14 demolition of un reinforced cement concrete in ground floor and paving not exceeding 15 cm thick ( below or above ground level ) complete all as specified and directed. 15 m & l hardcore of broken bricks of gauge n. exc 63mm, deposited spread and leveled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed. 16 m&l cement concrete ( 1:3:6 ) type c 2 using 40mm graded stone aggregate as in plinth protection, 75mm thick, surfaces finished even and smooth without using extra cement complete all as specified and directed. 17 m&lcement concrete ( 1:2:4 ) type b 1 using 20mm graded stone aggregate as in floor topping, 40mm thick, surfaces finished even and smooth without using extra cement complete all as specified and directed. 18 demolition of stone slabs and tiles laid bedded pointed in mortar of any description or thickness in floors, aprons etc. 19 m&l machine pressed precast conctete interlocking paver block with grey cement and pigmentsany shape and size confirming to is 15658 2006 of 60 mm thickness, m 35grade including laying ofsand cushioning, etc, complete allas specified and as directed.note : sand will be measured and paid seperately 20 m&l sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. 21 m&l cement concrete ( 1:3:6 ) , type c 1 using 20mm graded stone aggregate as in filling of steel chowkhats, bed blocks, coping etcincluding necessary form work complete all as specified and directed. 22 taking down wooden chowkhats or frames with shutters ( without taking off shutters from the frames ) of size not exceeding 1.50 sqm each complete all as specified and directed. 23 all as per item no 22here in before but size exceeding 1.5 sqm and not exceeding 4 sqm each. 24 taking down shutters of any description and refixing in the same opening exc 1 sqm and not exc 2 sqm each complete all as specified and directed. 25 m&l for cutting holes in brick wall built in cement mortar for fixing hold fasts and making good dismantled portion in cm ( 1:3 ) or in cement concrete 1:2:4 type b 1 , depth of embedded portion of hold fasts measured from the face of jamb into wall exc half brick but next one brick complete all as specified and directed. 26 supply and fixing factory made pressed steel frames made of 1.25mm thick ms sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long ms conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts / lugs etc complete all as specified and directed. 27 all as per item no 26 above here in before but size 125x60mm with double rebate. 28 s& f factory made solid pvc door frame of size 50 mm x 47 mm made of 5 mm plain colour pvc sheet reinforced with mild steel square tube complete all as specified in clause 8b.3.1 and shown on page 150 of mes schedule part ii ( 2010 ) . 29 s&f factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of ms tubes for top & bottom rails, ms frame covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rails with suitable pvc sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 b.2.1 of mes schedule part ii ( 2004 ) complete all as specified. make: rajshri or equivalent as approved. 30 s& f second class hard wood plain, solid straight chowkats and frame, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good disturbed surfaces of wall complete all as specified and directed 31 s&f factory made 35mm thick second class hard wood plain framed panelled shutters ( any number of panels ) , with panels of timber flat on both sides ( feather edge ) , or of veneered particle board medium density wood wood particle board with commericial face veneers and fitted to chowkats. 32 s&f factory made 35mm thick second class hard wood glazed and skelton shutters, open rebated and prepared to receive glass gauze, etc ( without sash bars ) , edges of framingplain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in ssr part i section 8 clause 8.24 ( a ) fitted to chowkat. 33 s&f factory made box type steel window with pintle hinges & 2 nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed. 34 s& f factory made box type steel window with pintol hinges & 2 nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed. 35 s& f factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed. 36 demolition of boarding of any description and in any position complete all as specified and directed. 37 s& f 25mm thickboarding second class hard wood& fixed with nails in any situationclean sawn with butt joints fixed in shelves partitions and shelves of built incup boards almirahs book cases toilet boxes racks , pelments and similar work complete all as specified and directed. 38 s & f 14 16 mm solid pvc board plain colour , fixed with screws or adhesive with complete accessaries as in shutters complete all as spd and directed. make : rajshree, echon or equallent as approved by ge 39 m&l 2nd class hw plain fillets square, rectangular in section clean swan, secured with nail or band including two coats of paint over a coat of primer n.exc 13 sqcm 40 s& f 18 19mm thick pre laminated particle board, flat pressed single layer type or three layer type with bwr type adhesive, medium density interior grade having one side decorative lamination and other side balancing white lamination as in pelmet boxor cup board shelf including 6 mm thick teak wood leaping on three sides and 20mm thich on hanging side & french polishing to edging, fixed in repair complete all as specified and directed. 41 s & f 3.00mm thick, plainsheet glass ordinary quality and glazing, with oil putty or with wooden beads ( supplied alongwith shutters ) , in squares n.exc 0.50 sqm complete all as specified and directed. 42 s & f galvanised mild steel wire cloth0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed. 43 s&f 300mm mild steel helical door spring including roller and roller plate complete all as specified and directed. 44 s &f in repair to 3mm thick, plainsheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 sqm incl. incl hacking out old broken glass and putty / beading complete all as specified and directed. 45 s &f in repair galvanised mild steel wire cloth0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staplescomplete all as specified and directed. 46 s& f ptmt tower bolts, 200 mm long and fixed with steel screws complete all as specified and directed. 47 s& f ptmt butt hinge, 100mm long, fixed with steel screws with brass / bronze hinge pin complete all as specified and directed. 48 s& f ptmt handle 125mm long fixed with steel screws complete all as specified and directed. 49 s&f 200mm long aluminium, anodisedbarrel tower bolts of extruded section, complete all as specified and as directed. 50 s&f 150mm extruded aluminium alloy handlecomplete all as specified and as directed. 51 s&faluminium alloy, anodised, sliding door bolt 300mm length, with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. 52 s&f butt hinges 100mm size exturded alu. alloy with galvanised mild steel hinge pin anodised and fixed type b21 complete all as specified and directed. 53 s&f butt hinges 125mm size exturded alu. alloy with galvanised mild steel hinge pin anodised and fixed type b 21 complete all as specified and directed. 54 s&f150 mm floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed. 55 s&f 4 lever aluminium mortice lock, vertical type size 100 mm complete all as specified and directed. 56 s&f hydraulicallyextruded aluminium body door closer regulated designation no 3 universal type suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 kg etc complete all as speciified and directed. 57 s& f hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified and directed. 58 s& f continuous ( piano ) hinges, mild steel bright finish or electro galvanised with flap ( when open ) 40 mm, fixed with steel screws complete all as specified and directed. 59 taking down cement plaster inlcuding racking out joints, hacking for keys, scrubing down with water, complete all as specified and directed. 60 m&l 10 mm thick rendering in cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished evenand smooth with out using extra cementcomplete all as specified and directed. 61 m&l rendering 15 mm thick in cement mortar ( 1:4 ) on any face of brick walls or conrete surfaces, surfaces finishedeven and fair complete all as specified & directred. 62 m&l rendering 5mm thick in cement mortar ( 1:3 ) on any face of brick walls or conrete surfaces, surfaces finished even and smooth without using extra cement, inceiling, soffits of chajja or similar location etc complete all as specified & directred. 63 m&l preparation of new plastered surfaces wall and applying two coats of oil bound distember over a coat of primer complete all as specified and directed. 64 m&l preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed. 65 m&l white wash in three coats on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed. 66 s&f galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded gi pipe complete all as specified and as directed. 67 s&f galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded gi pipe complete all as specified and as directed. 68 s&f pvc low level flushing cistern ( white ) of 10 liters capacity with inlet ball float valve, pvc flush pipe and necessary fixing arrangements and connecting to water pipe and wc etc and fixed in repairs complete all as specified and directed. 69 s&f in repairs15mm bore fancy type, chromium plated, with long shank and cup ( concealed type ) stop valves of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fixed in repairs complete all as specified and directed. 70 supply &fixingin repair 125 mmchromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union, complete all as specified and directed. 71 s&f in repairs pvc connection both end brass union and length 450 mm long for 15 mm bore pipe complete all as specified and directed. 72 s&f in repairs 15mm bore cp bib tap, fency typescrewed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. 73 s&f15mm bore chromium plated, fancy type pillar tap, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipe, as in repair complete all as specified and directed. 74 s & f in repair of cp whb mixer 15mm bore mixing and hot and cold water scrwed down for iron pipe and fixed. and waste system with 450mm long braided hoses complete all as specified and directed. 75 s&f chromium plated fancy type15mm bore dia hot and cold wallmixer with provision forover head with 115mm long bend pipe one upper side connecting legs and wall flanges complete all as specified and directed. note: flr 5219 n ( make:jaquor / equivalent ) ) 76 s & f in repair stop cock cast copper alloy screwed down, high pressure with with fancy type chromium platedscrewed both ends for iron pipe or union of 15 mm bore fixed in repairs complete all as specified and directed. 77 s&f600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board of commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers with alround aluminium beadingas fixed in repairs and all as complete all as specified and directed. 78 s&f 8 to 10 mm thickbevelled edge mirror of selected quality glass edges to be polished androunded , onfixed to wall withwooden plugs with chromium plated brass screws and cup washers as fixed in repairs and complete all as specified and directed. 79 s&f brass cp 20mm dia towel rail of 60cm long fixed with brackets at its ends as fixed in repairs and complete all as specified and directed. 80 s&f cp soapdish oval / squaretype as fixed in repairs and complete all as specified and directed. 81 s&f cp toilet paper holder with flap as fixed in repairs and complete all as specified and directed. 82 s&f 1mm thick stainless steel sink, plugs, washers, pvc waste pipe, union, cp coupling & cantilever brackets embedded in cement and sand mortar in wall , overall size of sink 495mmx420mm, bowl size 410mmx330mmx 160mm as in repair complete all as specified and directed. 83 s &f sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. 84 s&f pvc waste pipe, 32mm bore suitable to waste coupling pipe attach with rubber ring joints fixed to waste coupling of sinks / whbs. as fixed in repairs and complete all as specified and directed. 85 supply & fixedreplacement ofpressure jetfor ewc including pvc connection and cp fitting as fixed in repairs and complete all as specified and directed. 86 s & f in repair to cp towel ring square.complete all as specified and directed. 87 s&f health faucet ( jaquar model no: ald chr 585 ) ( abs body ) with 8mm dia1.00 m long easy flexible tube chormium coated finishand wall hook complete all as specified and directed. 88 s&f vitreous china wash down water closet pan ( pedestal pattern ) white / coloured cascade type640x360x690 ( monolithic flush cistern type ) make: jaquare model no:sls wht 6853s / cera cat no: s1013132 s single picece wc with pp seat cover , hinges fixing accessories set including flush cistern with s trap of size 220mm all as per manufacturing instructions and complete all as specified and directed. 89 s& f syphon kit including epdm rubber washer for monolithic orcascade type of flush cisternfor vitreous china10 ltr capacity as fixedin repairs complete all as specified and directed. 90 s&f vitreous china wash hand basin size 550x400 ( pedestal pattern ) including necessary fittings to fixed with wall complete set and brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed 91 s&f in repair rotational moulded triple layered polyethylene water storage tank of 500 litres capacity ( cylindrical vertical with closed top ) hoisted and fixed in position including taking down old pvc water tank complete allas specified and as directed. 92 s&f in repair rotational moulded triple layered polyethylene water storage tank of 1000 litres capacity ( cylindrical vertical with closed top ) hoisted and fixed in position including taking down old pvc water tank complete allas specified and as directed. 93 s& f pvc body toilet cabinet ( box type ) 600x450mmx125mm size with mirrorof selected quality glass having 5.5mm thickness and fixed to walls with screws and wooden / rawl plugs complete all as specified and directed. make: prayag or techno commercially equivalent of other makes. 94 s& f vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary cement concrete and 100 mm bore cast iron ‘p’ trap with 550 to 600 mm long neck for connecting wc to branch piece with cement joints, fixed as in repair, complete all as specified and directed. 95 s&f vitreous china white wash down water closet ( pedestal pattern ) including pvc seat cover and connection to drain or out going pipe and to flushing pipe anti syphonage pipe etc, fixed as in repair, complete all as specified and directed. 96 s&f toilet seat cover plastic for washdwon water closet with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. 97 s&f 1.00mm thick stainless steel plate racks of size 750x600x250mm complete all as specified and directed. 98 s&f vitreous china whb white flat back size of 550x400mm excluding taps waste chain and plug and porcelien stopper but including brakets 32mm dia waste pipe as fixed in repairs complete all as specified and directed. ( make : parryware, cera or techno equivalent ) 99 supply & fixed20mm dia mild steel pvccolour powder coatedcurtain rod with fancy type brackets including with all fittings as fixed in repairs and complete all as specified and directed. 100 taking down eaves gutters and rain water pipes ( any size or pattern ) , including all fittings heads shoes bends swan necks etc complete all as specified and directed. 101 s&f 110mm dia pvc ( swr ) pipes single socketed in any length with rubber ring jointsfixed to walls, complete all as specified and directed. 102 s&f 75mm dia pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. 103 s&f 75mm dia pvc ( swr ) with access door bends any radius, complete all as specified and directed. 104 s&f 110 mm dia pvc ( swr ) with access door bends any radius, complete all as specified and directed. 105 s&f pvc ( swr ) 75 mm floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. 106 s& fin repair 15mm bore ptmt ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed. 107 s& fin repair 20mm bore ptmt ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed. 108 dismantling of wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets complete all as specified and directed. 109 s & f in repair to hollow pvc wall lining consisting of 5mm thick single side prelam pvc sheet instead of plain colour sheet inclusive of solvent cement and fixing on pvc frame as per specified in mes schedule part i & ii complete all as specified and directed. 110 s & f in rep of gypsum board 6 to 7 mm thick in ceiling fixed with screw 60x60cm placed in ceiling ( angle 25mm x 25mm , main tee 38mmx23mm , sub tee 23mmx23mm ) incl aluminium anodised / powder coated snap grid frame 605x605 mm for false ceiling incl hanging arrangement complete all as specified and directed.note: the hanging stay wire shall not be less than 4.00mm thick all are included in the above mentioned item only. 111 dismantlingofsteel workincludingdoors, gatesbut excludingframed truss complete all as specified and directed. 112 s&f rolled section as in post / pillars where connected with angle cleat or other connecting plate etc of fe 410 w ( grade e 250 ) quality b including fabrication , erection and fixingcomplete all as specified and directed. 113 s&f rolled mild steel plates fe 410 w ( gde e 250 ) quality a ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes without any attachment complete all as specified and directed. 114 s&f mild steel screw bolts of 12 mm dia ( machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 15cm and n exc 22.5cm long complete all as specified and directed. 115 dismantlingplain or corrugatedsheetonroof covering complete all as specified and directed. 116 s& f pre painted galvatume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding towall, fixed with self tapping screws complete all as specified and directed. 117 s&f pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. 118 s & f 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed withj type or l typehookboltscomplete all as specified and directed. 119 s&f powder coated of ( any colour ) aluminium door window , ventilator etc fixed / sliding or pull and push type in shutter frames or shutters with two / three track sliding aluminium frame of jindal / hindalco ( or ) equivalent make of approved size, including necessary joining cleats, glazing clips, powder coated aluminium snap beading, screws, including necessary anodised aluminium fittings like handles etc including taking down completeall as specified as per manufacturers instructions.note: epdm rubber beading / gasket measured and paid seperatley. 120 s&f aluminium decogrill 10 mm thick with necessary chanels and clips dg 104 121 s&f solar control film 25 micron reflective sticked to glass panes as per manufacturers instruction complete all as specified and directed. 122 s&f epdm rubber beading around glass in aluminium windows / ventilator shutters. 123 s&f 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and directed. 124 dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of rwp and oht staging area or specifically ordered by engineer in charge in writing complete all as specified and directed. 125 demolition of mud phuska in roofs, any thickness, including leeping plaster ( whether full thickness removed or only a part thereof ) complete all as specified and directed. 126 m&l for brushing neat cement slurry with 3 kg of cement per square metre 127 m&l 10 mm thick screed bed or bedding layer of mortar in cm ( 1:4 ) with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane. note: wpc shall be measured and paid separately 128 m / l for 10mm thick on fair faces of brick work or concrete surfaces in cement mortor 1:4 mixed with water profing comund @3% by weight of cement content as in verticle surfaces and finished even and smooth without using extra cement. note: wpc measured and paid seperately. 129 supply only water proofing compound. 130 m&l tack coat of industrial bitumen 85 / 25 @ 1.20 kilogram per square metreincluding preparation of roof surfaces complete all as specified and directed. 131 m&l for app based polymeric membrane minimumweighing 3kg / sqm and minimum 3mm thick reinforced with polyster non wove fabric ( wt. not less than 150 gms / sqm ) laidon primed surface by forced application including bitumen primer complete all as specified and directed. 132 m & l for 80mm thick average consolidated thicknessmud phuska on flat roof ncluding 25mm thick mud plaster complete all as specified and directed. 133 s & f 40 mm thick brick tiles laid on mud mortar and joints grouted flus in cement mortar ( 1:3 ) mixed with 5% of crude oil by wt of cement on mud phuska complete all as specified and directed. 134 all as item no 133 here in before but except tiles 135 m&l plain cement concrete ( 1:2:4 ) , type b 0 using 12.5mm graded stone aggregate as in , kerbs, mud stop, rounded or chamfered on edges including form work complete all as specified and directed. 136 m & lfor preparing of olddecorated surfaces ( plastered or un plastered ) by brooming down and applying one coat of white wash on walls including cornices complete all as specified and directed. 137 m & lfor preparing of old decorated surfaces ( plastered or un plastered ) by brooming down and applying one coat of white wash to ceiling complete all as specified and directed. 138 m & lfor preparing of olddecorated surfaces ( plastered or un plastered ) by brooming down and applying one coat of colour wash on walls including cornices complete all as specified and directed. 139 m&l washing rubbing down and stopping of distempered and painted surfacesincl preparation and applying one coat of oil bound distemper complete all as specified and directed. 140 all as per above item no:139 but on ceiling 141 m&l complete removal of existing treatment of wall suface and applying two coats of oil bound distemper, over a coat of primer on a coat of wall care putty, complete all as specified and as directed. 142 m&lwashing rubbing down and stopping of distempered and paintedsurfacesincl preparation and applying one coat of cement based paint on wall surfaces including proper curing complete all as specified and directed. 143 m&l complete removal of existing treatment of walls applying two coats of cement based paint over one coat of cement primer on plastered surfaces complete all as specified and directed. 144 m&l for preparation of old wood or wooden based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 145 m&l for preparation of , old decorative steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 146 m&l complete removal of existing treatment on terra cotta floor surfaces like a pathway pavers , chequered, inlerlocking tile, roof tiles surfacesetcincluding necessary preparation of surfaces and applying twocoats of expoxy exterior emulsionpaint over a coat of primer complete all as specified and directed. 147 m&l for writing letters or figures ( block roman italic and indian ) 15 cm high on wall surfaces, so that the stand out boldly and solidly without showing signs of brush marks complete all as specified and directed. ( note : the letters to bewrite with in theblack synthetic enamel painted back ground, it is measured and paid to seperately ) 148 m&l preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide zink primer on steel surfaces complete all as specified and directed. 149 m&l preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 150 m&l for cleaning and removing all scale and dirt, etc, from 500 ltr tanks and from mouths of circulating pipes, etc incl disconnecting existing tanks, setting aside ( or lowering if required ) for repairs, cleaning, etc. and hoisting if required reconnecting and re fixing in position. 151 m&l for cleaning and removing all scale and dirt, etc, from 1000 ltr tanks and from mouths of circulating pipes, etc incl disconnecting existing tanks, setting aside ( or lowering if required ) for repairs, cleaning, etc. and hoisting if required reconnecting and re fixing in position. 152 easing of wooden window shutters / cb shutters ( one unit shall comprise of one window / cb / showcase irrespective of number of leaves ) for properly closing / opening, tightening of hinges or changing the position of hinges, adjustment of tower bolts sliding bolt including necessary nail and screwsetc. 153 easing of wooden door shutters ( one unit shall comprise of one panelled or skeltion door shutter irrespective of number of leaves ) for properly closing / opening, tightening of hinges or changing the position of hinges, adjustment of tower bolts sliding bolt including necessary nail and screwsetc. 154 taking down and refixing ofgypsum board 6 to 7 mm thick in ceiling fixed with screw 60x60cm placed in ceiling ( angle 25mm x 25mm , main tee 38mmx23mm , sub tee 23mmx23mm ) incl aluminium anodised / powder coated snap grid frame 605x605 mm for false ceiling incl hanging arrangement complete all as specified and directed 155 welding in repairs exc. 6mm but n. exc 9 cm in length, thickness of metal to be welded complete all as specified and directed. 156 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls, floors etc. 157 m &l point wiring complete with 1100 volts grade pvc insulated unsheathed frls cable of copperconductor, multi stranded of size 1.5 sqmm, single core, in and including new rigid non metallic pvc conealed conduit, with all accessories if require such as bends, reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks ( for housing lamp holders and light fittings etc ) and existing ms pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green pvc insulation connected to common earth dolly complete all as specified and directed for the followings : ( a ) one light / fan / bell pointcontrolled by one single pole one way switch. 158 ( b ) one socket outlet on the sameboard controlled by one single pole one way switch 159 ( c ) one 5 amps socket outlet independentcontrolled by one single pole 5 amp switch. 160 allas per itemno 2 mentionedhere in before but one three pin 15 amps switch socket out let on the independentboardwith 2.5 sq mmpvc insulated copper conductor and 2.5 sqmm copper conductor for continuous earthing complete all as specified and directed. 161 all as per item no 2 above but existing conduit and existing ms pressed steel / cast iron box complete all as speicifed and directed. ( a ) one light point / fan / bell point controlled by one single pole one way switch. 162 ( b ) one 5 amps socket outlet independent controlled by one single pole 5 amp switch. 163 all as per item no 5 above but existing conduit and existing ms pressed steel / cast iron box complete all as speicifed and directed. 164 supply & fixing switch piano flushtype single pole one way5 / 6 amp complete all as specified and directed. 165 supply & fixingswitch piano flush type 15 amps, single pole one way duly isi marked complete all as specified and directed. 166 supply & fixingsocket outlet 2 in one , 5 / 6 amps flush typeisi marked complete all as specified and directed. 167 supply & fixingsocket outlet, 2 in one6pin 5 and 15 ampspiano flush type complete all as specified and directed. 168 s & f ceiling rose surface type, pvc / polycarbonate , isolated, bakelite 65 x 50mm, 3 terminals isi marked complete all as specified and directed. 169 s & f lamp holder insulated body threaded dome pattern, suitable for bracket / batten fitting complete all as specified and directed. 170 s & f stepped type electronic fan regulater flush, socket type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed. 171 s & f bell push pianoflush type5 amps single pole duly isi marked complete all as specified and directed. 172 s & f bell ding dong ac 230 volts single pole complete all as specified and directed 173 s & f in repairmodular switch one way6 a, 1 module complete all as specified and directed. make precision / anchor / havells / legrand 174 s & f in repairmodular switch one way16 a, 1 module complete all as specified anddirected. make precision / anchor / havells / legrand 175 s & fin repair modular socket, 6a 2 / 3 pin combined 2 module complete all as specified anddirected. make precision / anchor / havells / legrand 176 s & fin repair modular socket, 6a16a 2 / 3 pin combined 2 module complete all as specified anddirected. make precision / anchor / havells / legrand 177 s & f in repairmodularwhite cover plate with frame, 1 module complete all as per specified anddirected. make precision / anchor / havells / legrand 178 s & fin repair modularwhite cover plate with frame, 2 module complete all as per specified anddirected. make precision / anchor / havells / legrand 179 s & fin repair modularwhite cover plate with frame, 3 module complete all as per specified anddirected. make precision / anchor / havells / legrand 180 s & f in repairmodularwhite cover plate with frame, 4 module complete all as per specified anddirected. make precision / anchor / havells / legrand 181 s & f in repairmodularwhite cover plate with frame, 6 module complete all as per specified anddirected. make precision / anchor / havells / legrand 182 s & f in repairmodularwhite cover plate with frame, 8 module complete all as specified and directed.. make precision / anchor / havells / legrand 183 s & fin repair modular bell push 6a, 1 module complete all as per specified anddirected. make precision / anchor / havells / legrand 184 s & fin repair modular step type regulator, 120 w 2 module complete all as per specified anddirected. make precision / anchor / havells / legrand 185 supply and fixing led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 186 supply & fixin repair led tube light fitting 9 watts batten type fixed on wall / ceiling etc.including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. 187 supply and fixing led luminaire 600 mm x 600 mm, 35 / 36 watt, 220 v ac recessed type with highefficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 188 supply and fixing led bldg security light fitting 35 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection complete all as specified and directed. 189 supply and fix in replacement of plastic ex fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 300mmcomplete all as specified and directed. 190 supply & fix in repair sheet metal enclouser spn dbs 8 way double door factory made powder coated out of crca mild steel sheet 1.2 mm thick wih metallic painting white series, 240 volts 200 amps rated enameled bus bar 8 way dust and vermin proof ssuitable for incorporation of mcbs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed. 191 all as item no 22 above but spn dbs 4 way. 192 s & f in repair sheet metal enclouser dbs tpn 4 way double door ( vertical type ) factory made powder coated out of crca mild steel sheet 1.2 mm thick wih metallic painting white series, 415 volts 200 amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of mcbs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed. 193 s & f mccb 63 amps 415 volts 16ka breaking capacity complete all as specified and directed. 194 s & f mcb tpn 415 volts 63 amps, 10 ka breaking capacity complete all as specified and directed. 195 s & f mcb single pole neutral ( spn ) 240 volts, 40 amps, 10 ka complete all as specified and directed. 196 s & f mcb single pole ( sp ) 240 volts, 6 to 32 amps, 10 ka complete all as specified and directed. 197 supply & fix in repair sub main wiring of 6 sqmm pvc insulated unsheathed frls cable multistranded copper conductor with earth wire of 6.0 sqmm pvc insulated unsheathed frls cable multistranded copper conductor including pvc conduit pipe 25 mm dia complete all as specified and directed.note: two run of single core 4 sqmm cable and one run single core 6.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length ) ....

Public Works Department - Punjab

37031526 providing and installation of furniture work for establishment of model career centre in district bureau of rojgar generation and training office at d.a.c jalandhar , i ) providing & installation of furniture , computer work station partition penel based partition system 60mm thickness height to be maintained uniformly at 1500mm from floor level, structure consists of powder coated aluminium extruded framework of properietary design with suitable provision for tile / glass cladding on both sides tiles to be either inserted into the edge of frame slide in or fixed from the front with a clip on mechanism. , supply and installation of the main table shall be of size 1200 width mm x 600 mm depth x 750 mm height. top surface of the table shall made up of mdf ( medium density fibre ) board . the main desk should contain in built key board pull out tray for keeping keyboard of computer. the front modesty panel of the table shall be made up of mdf board of size 1200 mm x 600 mm x 16mm . for personal storage one mobile pedestal ( 3 drawer unit ) shall be provided of size 510 mm width x 635 mm height and 445 mm depth. the storage pedestal shall also be made up of mdf duly finished , side unit size 750mmx450mmx750mm , top 25mm thick mdf board , side unit have 3 drawer one side .manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of computer desk the main table shall be of size 1200 width mm x 600 mm depth x 750 mm height. top surface of the table shall made up of mdf ( medium density fibre ) board . the main desk should contain in built key board pull out tray for keeping keyboard of computer. the front modesty panel of the table shall be made up of mdf board of size 1200 mm x 600 mm x 16mm . for personal storage one mobile pedestal ( 3 drawer unit ) shall be provided of size 510 mm width x 635 mm height and 445 mm depth attach with side panel on rhs one 200 mm wooden plate form for keeping cpu attach with lhs side panel.manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of fiber logo blacklit size 3.5x 2complete in all respect as per satisfaction of engineer in charge , supply and installation of glass door almirah product size: 915 mm ( w ) x 486mm ( d ) x 1981 mm ( h ) height. construction & material § welded construction. 0.8 mm thick crca for shelf & 0.9 mm thick crca for all other components. door glasses fitted to full height steel frame. thickness of glass 4mm, locking 2 way locking mechanism with shooting bolt. handle : chrome plated brass handle. shelving: height wise adjustable shelves 4 nos. uniformlydistributed load capacity per full shelf is 60 kg maximum . leveler m10 screw type leveler with hex plastic base. ( add 10mm to unit height and additional 10mm for adjustment. ) finish epoxy polyester powder coated to the thickness of 40 microns ( + / 10 ) . lock and key. all metal parts of glass door storwel should be powder coated with treated by seven tanks process before powder coating i.e. respectively with non electrolytic deepprocess to produce a protective oxide coating for smooth surface with matt finish anticorrosive powder coating of thickness 40 50 microns and oven baked for high resistance to scratch. chemical, thermal and mechanical stress. manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of revolving chairs chair mechanism centre pivot mechanism type of locking upright locking number of arm movement 2 ( up and down ) pedestal base nylon base armrest material polypropylene seat material pressed and moulded with pu foam backrest is made of two pieces injection moulded frame density of pu foam used in seat kg per cu meter ( ± 3 ) 35 density of pu foam used in backrest in kg per cu meter ( ±3 ) n.a backrest upholstered with inner frame upholstered with mesh fabric and mounted on main assembly seat upholstered with foam laminated mesh fabrics gsm / thickness of fabric ±5% ( gram / square meter ) 220 gram overall width ( ±10 mm ) 550 mm backrest height ±15 mm 410 mm backrest width ±10 mm 440 mm seat height ±10 mm 525 mm seat width ±10 mm 460 mm seat depth ±10 mm 410 mm thickness of ms plate joining the under structure with seat 1 mmthickness of plywood used in seat ±1 ( mm ) 12 mmthickness of plywood used in backrest ± 1 ( mm ) n.a pedestal size ( diameter in mm ) ±10 mm 650 mm thickness of polyurethane foam used in seat in mm ( ±2 mm ) 5 mmthickness of polyurethane foam used in backrest in mm ( ( ±2 mm ) n.a. manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of chair type non revolving and non tilting chair with armrest chair frame type cantilever armrest type continuous armrest seat type moulded backrest type net frame material configuration two piece frame material steel tube ( erw quality ) conforming to is: 1161 ( with latest amendment ) seat material moulded plywood seat material thickness 30 mm density of polyurethane foam used in seat ( ±2 kg / cub meter ) 35 seat upholstered with mesh fabric gsm of seat cover ( ± 3 gsm ) 390 gsm backrest material mesh with support of injection oulded polypropylene ( p.p ) density of polyurethane foam used in backrest ( ±2 kg / cub meter ) n.a backrest upholstered with mesh fabric seat depth ( ± 5 mm ) 390 mm seat width ( ± 5 mm ) 440 mm seat height from floor surface ( ± 5 mm ) 435 mm backrest width ( ± 5 mm ) 350 mm backrest height from seat ( ± 5 mm ) 300 mm. manufacturer should have iso 9001 issued by an nabcb authorised agency....

Public Works Department - Punjab

36838411 providing and installation of furniture work for establishment of model career centre in district bureau of rojgar generation and training office at d.a.c jalandhar , i ) providing & installation of furniture , computer work station partition penel based partition system 60mm thickness height to be maintained uniformly at 1500mm from floor level, structure consists of powder coated aluminium extruded framework of properietary design with suitable provision for tile / glass cladding on both sides tiles to be either inserted into the edge of frame slide in or fixed from the front with a clip on mechanism. , supply and installation of the main table shall be of size 1200 width mm x 600 mm depth x 750 mm height. top surface of the table shall made up of mdf ( medium density fibre ) board . the main desk should contain in built key board pull out tray for keeping keyboard of computer. the front modesty panel of the table shall be made up of mdf board of size 1200 mm x 600 mm x 16mm . for personal storage one mobile pedestal ( 3 drawer unit ) shall be provided of size 510 mm width x 635 mm height and 445 mm depth. the storage pedestal shall also be made up of mdf duly finished , side unit size 750mmx450mmx750mm , top 25mm thick mdf board , side unit have 3 drawer one side .manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of computer desk the main table shall be of size 1200 width mm x 600 mm depth x 750 mm height. top surface of the table shall made up of mdf ( medium density fibre ) board . the main desk should contain in built key board pull out tray for keeping keyboard of computer. the front modesty panel of the table shall be made up of mdf board of size 1200 mm x 600 mm x 16mm . for personal storage one mobile pedestal ( 3 drawer unit ) shall be provided of size 510 mm width x 635 mm height and 445 mm depth attach with side panel on rhs one 200 mm wooden plate form for keeping cpu attach with lhs side panel.manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of fiber logo blacklit size 3.5x 2complete in all respect as per satisfaction of engineer in charge , supply and installation of glass door almirah product size: 915 mm ( w ) x 486mm ( d ) x 1981 mm ( h ) height. construction & material § welded construction. 0.8 mm thick crca for shelf & 0.9 mm thick crca for all other components. door glasses fitted to full height steel frame. thickness of glass 4mm, locking 2 way locking mechanism with shooting bolt. handle : chrome plated brass handle. shelving: height wise adjustable shelves 4 nos. uniformlydistributed load capacity per full shelf is 60 kg maximum . leveler m10 screw type leveler with hex plastic base. ( add 10mm to unit height and additional 10mm for adjustment. ) finish epoxy polyester powder coated to the thickness of 40 microns ( + / 10 ) . lock and key. all metal parts of glass door storwel should be powder coated with treated by seven tanks process before powder coating i.e. respectively with non electrolytic deepprocess to produce a protective oxide coating for smooth surface with matt finish anticorrosive powder coating of thickness 40 50 microns and oven baked for high resistance to scratch. chemical, thermal and mechanical stress. manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of revolving chairs chair mechanism centre pivot mechanism type of locking upright locking number of arm movement 2 ( up and down ) pedestal base nylon base armrest material polypropylene seat material pressed and moulded with pu foam backrest is made of two pieces injection moulded frame density of pu foam used in seat kg per cu meter ( ± 3 ) 35 density of pu foam used in backrest in kg per cu meter ( ±3 ) n.a backrest upholstered with inner frame upholstered with mesh fabric and mounted on main assembly seat upholstered with foam laminated mesh fabrics gsm / thickness of fabric ±5% ( gram / square meter ) 220 gram overall width ( ±10 mm ) 550 mm backrest height ±15 mm 410 mm backrest width ±10 mm 440 mm seat height ±10 mm 525 mm seat width ±10 mm 460 mm seat depth ±10 mm 410 mm thickness of ms plate joining the under structure with seat 1 mmthickness of plywood used in seat ±1 ( mm ) 12 mmthickness of plywood used in backrest ± 1 ( mm ) n.a pedestal size ( diameter in mm ) ±10 mm 650 mm thickness of polyurethane foam used in seat in mm ( ±2 mm ) 5 mmthickness of polyurethane foam used in backrest in mm ( ( ±2 mm ) n.a. manufacturer should have iso 9001 issued by an nabcb authorised agency. , supply and installation of chair type non revolving and non tilting chair with armrest chair frame type cantilever armrest type continuous armrest seat type moulded backrest type net frame material configuration two piece frame material steel tube ( erw quality ) conforming to is: 1161 ( with latest amendment ) seat material moulded plywood seat material thickness 30 mm density of polyurethane foam used in seat ( ±2 kg / cub meter ) 35 seat upholstered with mesh fabric gsm of seat cover ( ± 3 gsm ) 390 gsm backrest material mesh with support of injection oulded polypropylene ( p.p ) density of polyurethane foam used in backrest ( ±2 kg / cub meter ) n.a backrest upholstered with mesh fabric seat depth ( ± 5 mm ) 390 mm seat width ( ± 5 mm ) 440 mm seat height from floor surface ( ± 5 mm ) 435 mm backrest width ( ± 5 mm ) 350 mm backrest height from seat ( ± 5 mm ) 300 mm. manufacturer should have iso 9001 issued by an nabcb authorised agency....

Public Works Department - Punjab

36791597 supplying and installation of furniture in aam clinics (aacs) using porta cabin at location i, location ii and location iii in the municipal corporation area of jalandhar phase iii (group no. 7) , chair for reception supplyingand installation of medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. , waiting area chair 3 seater supplyingand installation of three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , waiting area chair 2 seater supplyingand installation of two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm. , doctor table supplying & installationof executive table with credenza unit in completely knock down conditions with an overall size 1600mm x 1600mm x 750mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 800mm x 500mm x 750mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 1400mm x 575mm x 500mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , main chair for doctor supplyingand installation of a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm. , visitor chair for doctor supplyingand installation of a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm. , examination table for doctor room supplyingand installation of in position examination table. overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h. the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. it shall be provided with 30 mm thick mattress. the bed should be provided with 40 density 30mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealed. complete as per sample approved by architect & desired by engineer in charge. , stool for doctor, pharmacist room & in samplingroom supplyingand installation ofrevolving stool, ss top, powder coated, height adjustable (510mm 690mm). complete as per sample approved by architect & desired by engineer in charge. , storage for medicine supplyingand installation of steel almirah. the overall size of the almirah shall be 915mm (w) x 485mm (d) x 1980mm (h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick. , customized lab table supplying & installation storage unit with an overall size 1800mm x 600mm x 900mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. the sliding shutter shall be operated on sliding rail track and ss handle as well as push lock mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certificatio , supplyingand installation of moveable 3 fold screen of ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the ms frame will be powder coated in colour as complete as per sample approved by architect & desired by engineer in charge. , supplyingand installation of roller blinds at the designated locations with fabric/ texture complete as per sample approved by architect & desired by engineer in charge....

Public Works Department - Punjab

36791595 supplying and installation of furniture in aam clinics (aacs) using porta cabin at location iv, location v and location vi in the municipal corporation area of jalandhar phase iii (group no. 8) , chair for reception supplyingand installation of medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. , waiting area chair 3 seater supplyingand installation of three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , waiting area chair 2 seater supplyingand installation of two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm. , doctor table supplying & installationof executive table with credenza unit in completely knock down conditions with an overall size 1600mm x 1600mm x 750mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 800mm x 500mm x 750mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 1400mm x 575mm x 500mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , main chair for doctor supplyingand installation of a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm. , visitor chair for doctor supplyingand installation of a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm. , examination table for doctor room supplyingand installation of in position examination table. overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h. the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. it shall be provided with 30 mm thick mattress. the bed should be provided with 40 density 30mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealed. complete as per sample approved by architect & desired by engineer in charge. , stool for doctor, pharmacist room & in samplingroom supplyingand installation ofrevolving stool, ss top, powder coated, height adjustable (510mm 690mm). complete as per sample approved by architect & desired by engineer in charge. , storage for medicine supplyingand installation of steel almirah. the overall size of the almirah shall be 915mm (w) x 485mm (d) x 1980mm (h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick. , customized lab table supplying & installation storage unit with an overall size 1800mm x 600mm x 900mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. the sliding shutter shall be operated on sliding rail track and ss handle as well as push lock mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certificatio , supplyingand installation of moveable 3 fold screen of ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the ms frame will be powder coated in colour as complete as per sample approved by architect & desired by engineer in charge. , supplyingand installation of roller blinds at the designated locations with fabric/ texture complete as per sample approved by architect & desired by engineer in charge....

Public Works Department - Punjab

36636617 supplying and installation of furniture in various health clinics/aam adami clinic (aacs) in the municipal corporation area of jalandhar phase iii (group no. 7) (sewa kendra dhina, shaheed udham singh charitable health care centre, lamba pind, rain , i) providing & installation of furniture , chair for reception supplyingand installation of medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. , waiting area chair 3 seater supplyingand installation of three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , waiting area chair 2 seater supplyingand installation of two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm. , doctor table supplying & placing executive table with credenza unit in completely knock down conditions with an overall size 1600mm x 1600mm x 750mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 800mm x 500mm x 750mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 1400mm x 575mm x 500mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , main chair for doctor supplyingand installation of a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm. , visitor chair for doctor supplyingand installation of a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm. , examination table for doctor room supplyingand installation of in position examination table. overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h. the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. it shall be provided with 30 mm thick mattress. the bed should be provided with 40 density 30mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealed. complete as per sample approved by architect & desired by engineer in charge. , chair for pharmacist supplyingand installation of ergonomically designed, comfortable & aesthetically appealing mid back chair. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. the same shall be upholstered with leatherite tapestry 0.8mm thick and 535 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine. moulded pp arm shall be used with cushion and leatherite upholstery. for seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suite them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load. the seat size shall be 515±10mm(w) x 490±10mm(d) and back size shall be 510±10 (w) x 510±10mm(h) from seat & overall height = 945±10mm. , stool for doctor, pharmacist room & in samplingroom supplyingand installation ofrevolving stool, ss top, powder coated, height adjustable (510mm 690mm). complete as per sample approved by architect & desired by engineer in charge. , storage for medicine supplyingand installation of steel almirah. the overall size of the almirah shall be 915mm (w) x 485mm (d) x 1980mm (h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick. , customized lab table supplying & placing storage unit with an overall size 1800mm x 600mm x 900mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. the sliding shutter shall be operated on sliding rail track and ss handle as well as push lock mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certificatio , supplyingand installation of moveable 3 fold screen of ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the ms frame will be powder coated in colour as complete as per sample approved by architect & desired by engineer in charge. , supplyingand installation of roller blinds at the designated locations with fabric/ texture complete as per sample approved by architect & desired by engineer in charge. , supplyingand installation of steps for examination table in doctor room approved by the architect/ engineer in charge...

Public Works Department - Punjab

36598442 supply and installation of furniture in various health clinic (aacs) in the municipal corporation area of jalandhar phase iii (group no. 4) (office of acp north in dada colony, baba lal dyal mandir, partap bagh, rc board jalandhar cantt (silver oak s , i) providing & installation of furniture , chair for reception supplyingand installation of medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. , waiting area chair 3 seater supplyingand installation of three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , waiting area chair 2 seater supplyingand installation of two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm. , doctor table supplying & placing executive table with credenza unit in completely knock down conditions with an overall size 1600mm x 1600mm x 750mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 800mm x 500mm x 750mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 1400mm x 575mm x 500mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , main chair for doctor supplyingand installation of a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm. , visitor chair for doctor supplyingand installation of a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm. , examination table for doctor room supplyingand installation of in position examination table. overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h. the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. it shall be provided with 30 mm thick mattress. the bed should be provided with 40 density 30mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealed. complete as per sample approved by architect & desired by engineer in charge. , chair for pharmacist supplyingand installation of ergonomically designed, comfortable & aesthetically appealing mid back chair. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. the same shall be upholstered with leatherite tapestry 0.8mm thick and 535 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine. moulded pp arm shall be used with cushion and leatherite upholstery. for seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suite them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load. the seat size shall be 515±10mm(w) x 490±10mm(d) and back size shall be 510±10 (w) x 510±10mm(h) from seat & overall height = 945±10mm. , stool for doctor, pharmacist room & in samplingroom supplyingand installation ofrevolving stool, ss top, powder coated, height adjustable (510mm 690mm). complete as per sample approved by architect & desired by engineer in charge. , storage for medicine supplyingand installation of steel almirah. the overall size of the almirah shall be 915mm (w) x 485mm (d) x 1980mm (h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick. , customized lab table supplying & placing storage unit with an overall size 1800mm x 600mm x 900mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. the sliding shutter shall be operated on sliding rail track and ss handle as well as push lock mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certificatio , supplyingand installation of moveable 3 fold screen of ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the ms frame will be powder coated in colour as complete as per sample approved by architect & desired by engineer in charge. , supplyingand installation of roller blinds at the designated locations with fabric/ texture complete as per sample approved by architect & desired by engineer in charge. , supplyingand installation of steps for examination table in doctor room approved by the architect/ engineer in charge...

Military Engineer Services - Punjab

35811376 tender for provision of mob equipment stores for med regt ( fd regt ) and rewiring of bldg no. p 67 ( 12 qtrs ) or md accn of engr regt at 550 acre under ge ( east ) ferozepur cantt b / r workexcavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, for lying cables etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft loose soil complete all as specified and as directed. 2 m&l cement concrete in foundations 1:4:8 type d 2, ( 40mm graded stone aggregate as in sub base of foundation, filling and mass concrete complete all as specified and as directed. 3 m&l for brickwork with subclass ‘b’ bricks, straight or curved on plan exc 6m mean radius built in cm ( 1:6 ) complete all as specified and as directed. 4 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm soft / loose soil complete all as specified and as directed. 5 removing excavated material / soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 6 use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter rough finishedsurface of concrete complete all as specified and as directed. 7 use and waste of formwork to sides of pillars, posts, struts, piers, columns etc rough finishedsurface of concreteall as complete all as specified and as directed. 8 use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) rough finishedsurface of concrete complete all as specified and as directed. 9 use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm widerough finishedsurface of concretecomplete all as specified and as directed. 10 use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finishedsurface of concretecomplete all as specified and as directed. 11 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed. 12 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) columns, pillars, piers, posts and struts complete all as specified and as directed. 13 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. 14 m&l rcc design mix m 25 ( 20mm graded stone aggregate ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. 15 m&l mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 16 all as per item no 15 above but 5mm dia and over upto and incl 10mm dia in stirupps, spacers and binders etc complete all as specified and as directed. 17 m&l rendering 12mm thickin cement mortar ( 1:4 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed. 18 m&l rendering 15mm thickin cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed. 19 m&lrendering 10 mm thick cement plaster on ceiling surfaces in cement mortar 1:4 finished fair and evenwithout using extra cement complete all as specified and as directed. 20 supply only integral water proofing compound conforming is 2645 1975 of approved make complete all as specified and as directed. 21 m&l preparation of newly plastered surfaces of walls etc, and applying three coats of white wash complete all as specified and as directed. 22 m&l preparation of new plastered surfaces of ceiling & applying two coats of white wash complete all as specified and as directed. 23 m&l applying double coats of bitumen elastometric waterproof coating as on damp proof course / roof including cleaning of surfaces complete all as specified and as directed. 24 m&l 75mm thick cement concrete 1:4:8 type c 2, using 40mm graded brick aggregate as in sub floor, sub base etc, finishing surfaces rough to receive the topping layer all as complete all as specified and as directed. 25 m & l machine pressed precast conctete interlocking paver block any shape and size confirming to is 15658 2006 of 60 mm thickness m 35 grade, jointed and pointed with gray cement and no pigment over sand cushioning complete all as specified and directed. 26 m & l sand filling under floors or in foundations including watering and consolidationcomplete all as directed by engieer in charge . 27 m&l 75mm thick cement concrete ( 1:3:6 ) type c 1 using 20mm graded stone aggregate as in plinth protection, surfaces finished even and fair without using extra cementincluding provision of construction joints complete all as specified and as directed. 28 m&l 75 mm thick cement concrete ( 1:2:4 ) type b 2 using 40mm graded stone aggregate as in floor topping, surface finished even and smooth without using extra cement complete all as specified and as directed. 29 m&l glass dividing strips, 3 mm thick and 38mm width of strip, inserted in position, conform to design complete all as specified and as directed. 30 s&f pressed steel frames ( 1.25mm sheet thickness ) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mmincluding one shop coat of red oxide primer complete all as specified and as directed. 31 s&f of 40mm thick flush door shutter of solid core construction with particle board core and plywood face panels, commercial type on both sides one face is covered with decorative face veneerwith lipping / frame to match complete all as specified and as directed. 32 s&f factory made box type steel window with pintal hinges & 2 nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing no cejz / td 06 / 07 & cejz / td 07 / 07. 33 s&f factory made box type steel window with pintal hinges & 2 nos 150 mm mild steel tower bolts to each shutter, steel handle and withoutglazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing no cejz / td 06 / 07 & cejz / td 07 / 07. 34 s&f steel ventilators fixed type complete with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and as directed. 35 mild steel framed work of e 165 ( fe 290 ) as in grills / guard bars shouldered with steel window / ventilator frames including red oxide primer coat complete all as specified and as directed. 36 s&f mild steel door handles, stove enameled black, medium wt 125 mm long and fixed with steel screws complete all as specified and as directed. 37 s&f mild steel barrel tower bolts, stove enameled black, with bright bolt, medium weight 150 mm long and fixed with steel screws complete all as specified and as directed. 38 s&f 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified and as directed. 39 s&f 3 mm thick, plainsheet glass ordinary quality and glazing, with oil putty or with wooden beads ( supplied alongwith shutters ) , in squares n.exc 0.50 sqm complete all as specified and as directed. 40 s&f stainless steel wire cloth0.56 mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staplescomplete all as specified and as directed. 41 m&l cement concrete ( 1:3:6 ) type c 1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc, complete all as specified and as directed. 42 m&l preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed. 43 m&l preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and as directed. 44 m&l preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paintcomplete all as specified and as directed. 45 e / m worksm&l for point wiring with 1.5 sqmm ( nominal area ) , pvc insulated, frls multistranded, single core unsheathed, copper conductor cables drawnthrough and including pvc conduit with allaccessories concealled in wall and fixed to ceiling etc. with and including 1.5 sqmm ( nominal area ) pvc insulated, frls unsheathed, multi stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth dolly including sunken boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for mounting switches, sockets, regulators etc complete for one light / fan / bell point controlled by one , one way switch all as specified and directed. ( a ) one light point / fan point / exhaust point controlled by one single pole one way switch. ( note: wiring shall be done in colour coding ) 46 all as per item no 45 hereinbefore butone 3 pin socket outlet 5 amps independent boardcomplete all as specified and as directed. 47 all as per item no 45 hereinbefore but one 3 pin socket outlet 5amps on the same board with other switches complete all as specified and as directed. 48 all as per item no. 45 here in before but one 15 amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 sqmm pvc insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 2.5 sqmm green colours pvc insulated, unsheathed, stranded copper conductor cable. 49 all as per item no. 45 here in before but one 15 amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 sqmm pvc insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 4.0 sqmm green colours pvc insulated, unsheathed, stranded copper conductor cable. 50 s&f switch piano flush type 6 amps, single pole one way, white in colour, duly isi marked complete all as specified and directed. 51 s&f switch piano flush type 20 amps, single pole one way, white in colour, duly isi marked complete all as specified and directed. 52 s&f socket outlet2 in 1, 5 pin, 6 amps, white in colour, duly isi marked complete all as specified and directed. 53 s&f socket outlet, uni, 2 in one10 amps & 20 amps, white in colour, duly isi markedcomplete all as specified and directed. 54 s&f ceiling rose surface type, 240 volts, 50 hz, 6a, pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals dulyisi marked complete all as specified and directed. 55 s&f rotary stepped type electronic fan regulator for ceiling fan 1200 / 1400mm size, 240 volts, 6 amps, 100w, white in colour, duly isi marked complete all as specified. 56 s&f lamp angle holder ( plastic ring ) , 240 volts, 50 hz, 6a, white in colour, duly isi marked complete all as specified and directed. 57 s&f led bulb of 9 watt, b22, 6500k all as specified and directed. 58 s&f 20w, 6500 k, 4 feet led square tube light fitting, energy efficient fixed to wall / ceiling etc complete all as specified and as directed. 59 s&f led sleeky bldg street light ( lens ) fitting of 35 watts, 6000k, including gi bracket bend to shape made out of gi pipe light grade of 25 mm, size up to 1.2 mtr long etc complete with ms clamps made of 25x3mm ms plate, duly painted with two coats of aluminium paint with nuts / bolts / washers and all fixing arrangements to wall / pole, including connecting up with 2 core copper flexible wire of size 23 / 00.0076 complete all as specified and as directed. 60 s&f exhaust fan heavy duty with louvers complete of sweep size 300mm, 900 rpm, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of pvc flexible copper cable of size 23 / 00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and as directed. 61 s&f ceiling fan 1200mm sweep, ac single phase 230 volts 50hz, at bldgs upto 5 mtrs height, including provision of flexible cable 3 core copper conductor of size 23 / 0.0076 of suitable length from ceiling rose to ceiling fan upto 1.5 mtr for giving connection and all hanging arrangement i.e. standard down rod, hanging clamp, with rubber real nuts bolts, spring washers and locking of splite pin, plastic canopy with screw compete without fan regulator and marking of mes nos with black synthetic enameled paint all as specified and as directed. 62 s&f factory made sheet metal enclosures double door type made out of crca 1.2 mm thick m.s. sheet, powder coated, partly embedded in wall, ip 43 protection, vtpn db with 200 amps rated bus bar, 4 way, 415 volts, vertical type, dust and vermin proof, suitable for incorporation of mccbs / mcbs, factory made, including thermal based release adjustable type 4 pole 63 amps, 50 hz, 415 volts with rupturing capacity 16 ka and making good distrubbed surfaces with matching colour, complete all as specified and as directed. 63 s&f factory made sheet metal enclosures double door type made out of crca1.2 mm thick m.s sheet, powder coated, spn db with 200 amps rated bus bar, 8 way, ip 42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of mcbs duly cocealled in wall, factory made, including making good distrubbed surfaces with matching colour complete all as specified and as directed. 64 s&f mcb spn, 40 amps, 240 volts, b series, 10ka duly isi marked, complete all as specified and as directed. 65 s&f mcb sp, 6a 32 amps, 240 volts, b series, 10ka duly isi marked, complete all as specified and as directed. 66 m&l for sub main wiring with two single core 2x4 sqmm pvc insulated and unsheathed stranded copper conductoralongwith earth wire 4.0 sqmm drawn in including pvc rigid conduit connected to main board complete all as specified and directed ( note: two runs cable and one number earth wire and suitablepvc conduit shall measured together as unit length ) . 67 m&l for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanised iron or steel wire complete all as specified and as directed. 68 m&l for earthing complete with galvanized steel plate elecrode of size60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead gi wire of 4mm dia ( 8 swg ) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. the other end of gi earth wire is connected to main switch board and protected by light grade gi pipe of 15 mm bore. provision of 20mm bore light grade gi pipe for watering including gi funnel and wire mesh. pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. cement concrete chamber of pcc ( 1:3:6 ) type c 2 using 40 mm graded stone aggregate.the chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate and ms angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in electrical plate no 3 of ssr part 1 ( 2009 ) . 69 supplying, laying, jointing and testing xlpe insulated, armoured, electric cables ( heavy duty ) with aluminium conductor, 1100 volts, grade cross sectional area 25 sqmm 4 core confirming to is:7098 1985 laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and as directed. ( note: excavation & earth work, cable preotection coverand sand cushion shall be measured &separately ) 70 m&l dry and clean fine sand for cable cushioningto underground cable protection, complete all as specified and as directed. note punned down thickness shall be measured. 71 s&f cover to underground cable with one layer of bricks using sub class ‘b’ bricks ( old size ) laid flat across the cable complete all as specified and as directed. 72 s&f mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles / walls, laid under floor / road crossings, complete with and includingclamps socket & elbow etc complete all as specified and as directed. 73 taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5 / 15 amp points complete withfitting and fixtures such as switches, sockets, c / rosess, holders and bracket fittings with battens / conduits / wires, t / l fittings and making good the disturbed surfacesof walls and roofs etc.and to match with existing colour complete all as specified and directed. 74 taking down carefully unserviceable main switches and distribution boards with fuses / mcbs ( single phase or three phase ) of any capacity complete all as specified and as directed. 75 taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified 76 s&f bell push flush, type 6 amp single pole one way, white in colour, duly isi marked complete all as specified and as directed. 77 s&f door bell ding dong single phase 240 volts, white in colour, duly isi marked complete all as specified and as directed. 78 s&f batten holder ( with metal ring ) , 240 volts, 50 hz, 6a, white in colour, duly isi marked complete all as specified and as directed. 79 s&f factory made three phase and neutral sheet steel made out of crca 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing mcbs and the second for protection of mcbs fitted with colour bus bar of capacity 200 amps, neutral link, earth bar and din rail suitable for use on 240 / 415v, 50hz supply, vtpn db, partly immersed in wall, including of mccb 4 pole adjustable thermal & fixed magnetic type 100 amps, 50hz, 415 volts with rupturing capacity 16 ka and making good distrubbed surfaces with matching colour, complete all as specified and as directed. 80 s&f mcb spn, 40a 63amps, 240 volts, c series, 10ka duly isi marked, in mcb db, complete with connection testing and commissioning complete all as specified and as directed. 81 m&l for sub main wiring with two single core 2x6 sqmm frls insulated and unsheathed stranded copper conductoralongwith earth wire 6.0 sqmm frls drawn in includingrigid conduit connected to main board complete all as specified and directed ( note: two runs cable and one number earth wire and suitableconduit shall measured together as unit length ) . 82 cutting holes making good the distributed surface, grouting nuts for fixing of exhaust fans complete all as specified and directed. 83 m&l for disconnecting electric meter of any cap and refixing same after rewiring, in meter box including connection complete all as specified and as directed. 84 s&f sheet metal meter box single door minimum size 35x50x25cm for electric meter factory made of ms sheets / crca sheet duly painted with powder paint and door hinged locking arrangement conforming to is 5039 of 1983. the electric meter / switch box shall be suitable for fixing one number of electric meter and knock out holes for incoming and outgoing cable. before the powder paint process the sheet steel shall go through the anti corrosion conditioning process in not less than seven tank process. concealed in wall, including making good distrurbed surfaces with matching colour, complete all as specified and as directed. 85 fixing or hanging only ceiling fans height upto 3mtr to 5 mtrs ceiling height of bldg including three core fr pvc insulated & overall round sheathed flexible with pvc, colour of cores are red, black & yellow / green is for earthing. sheath colour is black of cable size 23 / 0.0076 complete all as specified. ( note : ceiling fans obtained / taking down from item sr no.73 as above ) ...

Department of Higher Education - Punjab

35797109 bids are invited for furniture for office mse mesh high back chair , mesh cantilever chair , table , side table , almira , premium leatherette total quantity : 9...

Military Engineer Services - Punjab

35563858 tender for addn / altn of 134 jco and or pre map md accn at abohar mil stn ( job no 10camwp / 2022 23 / 01 ) taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) areanot exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by engineer in charge. 3 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) areaexceeding 1.50 sqm but not exceeding 4 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by engineer in charge. 4 taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets / planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by engineer in charge. 5 supply & fixing aluminium sliding windowthree trackwith frame & two glass shutters using 4 mm thick glass tinted modi guard and oneshutter with stainless steel wire gauge wirecloth 0.31 mm nominaldia of wire and width of aperture 1.61 mm using aluminium powder coated section ( minimum thickness of powder coating not less than 50 micron ) including approved fittings like aluminium cleat, pvc track, bearing, handle lock, rubber beading etc complete all as specified and as directed by engineer in charge.note: size of aluminium section of make jindal main 2010 or equivalent in make mentioned in appx a to pss ii ( equivalency approved by ge ) shall be as under : ( i ) three track top and vertical section no 20621. ( ii ) three track bottom sectionno 20620 ( iii ) shutter vertical section section 20604 ( iv ) shutter top and bottom section 20604 ( v ) shutter vertical middle ( interlock ) section 20605 ( vi ) cost of glass and wire cloth shall be included in the unit rate. 6 supply & fixing aluminium anodised frame, made out of aluminium sectionpowder coated ( minimum thickness of powder coating not less than 50 micron ) for window, ventilators and aluminium partition with one or more rebates including joining cleat for fixing etc., the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners. aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and as directed by engineer in charge.note : the weight of each section shall be physically ascertained through a board of officers convened by ge and payment shall be made only after the actual weight at site. 7 supply & fixing anodised aluminium window shutter ( glazed or gauzed ) , side hung type without sash bars, made out of aluminium section weighing not less than 0.55 kg / mtr, powder coated ( minimum thickness of powder coating not less than 50 micron ) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings ( each shutter ) such as peg stays 150mm long ( 1 no ) , hinges type b 21 100mm long ( 2 nos ) suitable handle ( 1 no. ) , complete all as specified and as directed by engineer in charge.note : aluminium chowkhat / frame, glass, wiremesh and grill where required shall be measured and paid separately under appropriate item of boq. 8 supply & fixing aluminium powder coated grill weight not less than 1.50 kg / sqm in windows, ventilators including fixing material complete all as specified and as directed by engineer in charge. 9 supply & fixing fiber glass reinforced plastic ( frp ) door frame of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. the laminate door frame moulded with two resistant grade unsaturated polyester plain and chopped mat. door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiber glass from all sides. m.s. stay shall be provided at the bottom to steady the frame., complete all as specified and as directed by engineer in charge. 10 supply and fixing to existing door frames 30mm thick glass fibre reinforced plastic ( frp ) panelled door shutter of required colour and approved brand and manufacture made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick frp laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick frp laminate for panels conforming to is: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of engineer in charge. 11 supply & fixing factory made prefabricated pressed steel door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary ms rawl plug / bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with locking arrangement using mild steel mortise lock 4 levers with 2 nos of keys of size 100mm ( make godrej / harison / navtal ) including ms chromium plated handle and 2 nos ms locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by ms sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface ( not visible from front ) and hammer tone paint on exterior surface ( visible from front ) as per godrej pattern including taking out old shutter with frame complete all as specified and as directed by engineer in charge. 12 material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick pvc sheet ( prelam ) having one side decorative laminated sheet ( for shutter, back side of cabinet, sides of cabinet, partition and shelves etc ) . all the edges of shutter and front exposed edge of partition / shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. including all required fixing material such as ss brackets, screws, adhesive etc., including taking out old any type cabinet complete all as specified and as directed by engineer in charge.note : ( i ) the area of each sheet ( shutter, back side of cabinet, sides of cabinet, partition and shelves ) shall be measured in sqm for payment. ( ii ) magnetic catcher, handle / knob, continuous piano hinges and pvc frame ( where required ) shall be measured and paid separately under appropriate item of boq. ( iii ) any other material required for making / fixing / hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. 13 supply and fixing magnetic catcher fixed with steel screw complete all as specified and as directed by engineer in charge. 14 supply and fixing 40mm dia, cupboard knobs brass, fixed with nut, screw and washer bright finish complete all as specified and as directed by engineer in charge. 15 supply & fixing continuous ( piano ) hinges, stainless steel, bright finish, width of flap when open 30mm complete all as specified and as directed by engineer in charge . 16 supply and fixing solid pvc frame ( single rebated ) of size 60mm x 30mm made out of solid pvc foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal csk screws complete all as specified and as directed by engineer in charge. ( note : frame shall be elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life ) 17 supply and fixingfactory made pressed steel frames of size 125 x 60mm ( thickness of sheet shall be 1.25mm ) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable nos as directed for each leaf, and making good the wall with plaster in cm 1:6 complete all as specified and as directed by engineer in charge.note : butt hinges shall be measured and paid separately under appropriate item of boq as supply only. 18 supply and fixingfactory made pressed steel frames of size 105 x 60mm ( thickness of sheet shall be 1.25mm ) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable nos as directed for each leaf, and making good the wall with plaster in cm 1:6 complete all as specified and as directed by engineer in charge.note : butt hinges shall be measured and paid separately under appropriate item of boq as supply only. 19 material and labour for pcc ( 1:3:6 ) type c 1, using 20 mm graded aggregated as in back filling of pressed steel door frame / chowkhat and bed block for fixing of hold fast complete all as specified and as directed by engineer in charge 20 supply & fixing factory made plain framed panelled shutter 35mm thick made out of 2nd class hard wood with lock rail and panel ( two panels ) inserts of 9mm bwp commercial ply. the size of rails and styles as per is 1003 ( part i ) , kiln seasoned and chemically pressure treated complete all as specified and as directed by engineer in charge. 21 supply & fixing factory made glazed and skeleton shutter 35mm thick made out of 2nd class hard wood kiln seasoned and chemically pressure treated, open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, fitted with cut and mitred beads for securing glass, gauze etc.; sizes of members of shutters as specified in ssr part i, section 8, clause 8.24 ( a ) ;complete all as specified and as directed by engineer in charge. 22 supply only 100mm long stainless steel butt hinges heavy duty type b 21 complete all as specified and as directed by engineer in charge. 23 supply and fixing 100mm long stainless steel butt hinges heavy duty type b 21 including stainless steel screws complete all as specified and as directed by engineer in charge. 24 supply and fixing anodised aluminium handle cast type 150mm long complete all as specified and as directed by engineer in charge. 25 supply and fixing in replacement anodised aluminium handle cast type 150mm long complete all as specified and as directed by engineer in charge. 26 supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm longcomplete all as specified and as directed by engineer in charge. 27 supply and fixing in replacement aluminium anodised barrel tower bolt of extruded section, 200mm longcomplete all as specified and as directed by engineer in charge. 28 supply & fixingaluminium anodised sliding door bolts 300mm long, with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by engineer in charge. 29 supply & fixing in replacement aluminium anodised sliding door bolts 300mm long, with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by engineer in charge. 30 supply & fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm, complete all as specified and directed by engineer in charge. 31 supply & fixingin replacement floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm, complete all as specified and directed by engineer in charge. 32 supply and fixing mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to frame with screw complete all as specified and as directed by engineer in charge. 33 supply & fixingin replacement mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to frame with screw complete all as specified and as directed by engineer in charge. 34 supply and fixing curtain rod 25mm dia ms pipe with ivory coloured pvc coated, wall thickness of pipe not less than 20 guage, including fancy type brackets and pair of decorated end knobs ( finials ) , stop roller etc. as per site requirement, fixed to wall with fixing accessories, including taking down old existing curtain rods any description complete all as specified and as directed by engineer in charge. 35 supply & fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by engineer in charge 36 supply & fixing in replacement stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by engineer in charge 37 supply & fixing 4mm thick sheet glass ordinary quality in squares / retangular not exceeding 0.5sqm in each pane ( aluminium window / ventilator ) complete all as specified and as directed by engineer in charge. note : aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window / ventilator of boq. 38 supply & fixing, 4mm thick figured glass pin head type in squares / retangular not exceeding 0.5sqm in each pane complete all as specified and as directed by engineer in charge.note : aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window / ventilator of boq. 39 roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc. complete all as specified and as directed by engineer in charge. 40 material and labour for non skid ceramic light coloured tiles7 to 8 mm thick squarearea of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile includingnecessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer ( screed bed ) in cement mortar ( 1:6 ) and finish the surface rough to receive the tile complete all as specified and directed by engineer in charge. 41 material and labour for non skid ceramic light coloured tiles 7 to 8mm thick square or rectangular as in skirting ( cut from same size and type as floor tile ) , dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile includingnecessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer ( rendering ) in cement mortar ( 1:4 ) and finish the surface rough to receive the tile including making good plaster surfaces ( above skirting tile ) to match the existing complete all as specified and as directed by engineer in charge. 42 demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge. 43 material and labour for glazed ceramic coloured tiles light shade of size 300mmx 450mm, 7mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer ( rendering ) in cement mortar ( 1:4 ) and finish the surface rough to receive the tile complete all as specified and as directed by engineer in charge. 44 dismantling of stone slabs of any description or thickness in floors, plateform, apron etc laid bedded and pointed in any mortarincluding removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge. 45 material and labour 18 20mm thickness approved shade granite of minimum size equal to width of slab ( not less than 610mm ) machine cut, granite duly factory grinding and polishing and chamfering the outer edges ( table rubbed and mirror polished ) as in cooking platform and like laid over and including 20mm thick cement mortar ( 1:4 ) screed bed including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by engineer in charge. 46 material and labour for machine cut 20 to 25 mm thick, kota stone slab ( size of slab not less than 550x450mm for flooring and in single piece for treads of staircase ) , laid over and including 20 mm thick bedding layer in cement mortar ( 1:6 ) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing / grinding ( mirror finish ) andpolishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by engineer in charge. 47 material and labour for machine cut 18mm thick, kota stone slab as in skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar ( 1:3 ) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing / grinding ( mirror finish ) and polishing by machine, including machine cutting to make it square or rectangularcomplete all as specified and as directed by engineer in charge. 48 demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge 49 material and labour for water proofing treatment to sunken slab and adjoining vertical surfaces as per any one of the two method as specified in pss ii respective clause of ca complete all as directed by engineer in charge / ge. note : ( i ) work shall be executed through specialized agency ( ii ) the treatment shall be carried out as per the manufactures instructions and as directed by the engineer in charge. the name of firm shall be got approved from cwe before carrying out the work. ( iii ) only plan area will be measured for payment. treatment should be continue upto 450mm height on vertical walls. ( iv ) pcc filling under sunken area will be measured & paid separately. 50 material & labour for pcc ( 1:5:10 ) type e2 using 40mm graded stone aggregate as filling of sunken floors complete all as specified and as directed by engineer in charge. 51 material & labour for 40 mm gi pipe medium grade, made to shape as in spout pipe 60cm long in sunken / verandah / balcony including making hole and making good with cement mortar complete all as specified and as directed by engineer in charge. 52 dismantling brick terracing tiles single layer from roof laid and pointed in cement mortar ncluding cleaning and stacking serviceable tiles for re use and balance unserviceable tiles removing from the site complete all as specified and as directed by engineer in charge. 53 demolition / taking out of mud from roofs, any thickness, including removing / cutting uprooting grass, vegetations and roots of small plants etc on roof and surrounding / parapit wall etc, including removing rubbish material from building and thrown in low lying empty area ( as per direcction of age ) at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge 54 material and labour for preparing surface of top roof slab including sides of parapits and cleaned of all foreign materials such as fungues, moss, dust, loose particle etc by wire brushing, sprinkling water on the surface and ensure water does not stand anywhere. if it is so, the roof surface shall be leveled with cement mortar and after that surface shall be painted with one coat of cold applied bituminous primer @ 0.40 ltr per sqm, applied over primed surface app based polymeric membrane minimum weighing 3 kg / sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt. not less than 150 gms / sqm ) laid on primed surface by forced application, torching with overlaps as recommended by the manufacturer complete all as specified and as directed by engineer in charge. 55 material and labour for pcc ( 1:4:8 ) using brick aggregate as in roof minimum average thickness 75mm and increasing uniformly towards ridges to obtain a chain slope 1:40, the top shall be trowelled with the addition of jaggery solution and finished smooth complete all as specified and as directed by engineer in charge. 56 material and labour for 40mm thick brick tiles laid / bedded on screed bed 15mm thick in cement mortar ( 1:6 ) , on existing lime concrete surfaces of roof, joints grouted flush in cement mortar ( 1:3 ) mixed with liquid wpc @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of mes sch part i ( 2009 ) complete all as specified and as directed by engineer in charge. ( note : water proofing compound shall be measured & paid separately as supply only ) 57 material and labour for 40mm thick brick tiles ( old serviceable tiles obtained from demolition / dismantled itemshall be reused ) laid / bedded on screed bed 15mm thick in cement mortar ( 1:6 ) , on existing lime concrete surfaces of roof, joints grouted flush in cement mortar ( 1:3 ) mixed with liquid wpc @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of mes sch part i ( 2009 ) complete all as specified and as directed by engineer in charge. ( note : water proofing compound shall be measured & paid separately as supply only ) 58 material and labour for covering the crumple joint between walls, beams, columns by 0.56 mm thick plain aluminium sheeting, alloy 31000 h4 in ridges, hips, valley gutter, drip and straight flashing ( length and girth as fixed ) including fixing material and takig out old sheet complete all as specified and as directed. 59 providing and injecting approved grout in proportion stirrer mixed acrylic polymer of approved make @ 2% of weight of cement used modified cement slurry non shrinks compound in concrete / rcc work. made with recommended by the manufacture into cracks / honey comb area of concrete / masonry by suitable gun / pump at required pressure including cutting of nipples after curing etc. complete as per directions of ge. note : the payment shall be made on the basis of actual weight of approved grout injected. 60 material and labour for 75 mm thick pcc ( 1:3:6 ) type c 2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning point, filling the joints withbituminous sealing compound of grade ‘a’ / bitumen mastic filler / sealant complete all as specified and as directed by the engineer in charge. 61 taking up or down existing galvanised steel water tubing ( gi pipe ) 15mm bore including fitting / connection from wall, ceiling, floor etc. complete all as specified and as directed by engineer in charge. 62 re fixing old serviceable 15mm bore galvanised steel water tubing ( gi pipe ) but new fittings like elbow, tee, union, socket, reducer etc. in new or old portion / position to walls, ceiling, floor etc complete all as specified and as directed by engineer in charge. ( note : old serviceable pipe obtained from taking up or down ( here in before ) item of this boq shall be reused after necessary cleaning internally and rerunning the old screw threads as required. 63 supply and fixing galvanized steel tubing ( gi pipe ) medium grade 15mm bore isi marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by engineer in charge. 64 taking up or down existing galvanised steel water tubing ( gi pipe ) 20mm bore including fitting / connection from wall, ceiling, floor etc. complete all as specified and as directed by engineer in charge. 65 re fixing old serviceable 20mm bore galvanised steel water tubing ( gi pipe ) but new fittings like elbow, tee, union, socket, reducer etc. in new or old portion / position to walls, ceiling, floor etc complete all as specified and as directed by engineer in charge. ( note : old serviceable pipe obtained from taking up or down ( here in before ) item of this boq shall be reused after necessary cleaning internally and rerunning the old screw threads as required. 66 supply and fixing galvanized steel tubing ( gi pipe ) medium grade 20mm bore isi marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by engineer in charge. 67 supply and fixing galvanized steel tubing ( gi pipe ) medium grade 40mm bore isi marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by engineer in charge.note for item no 61 to 67 : cost for cutting chases / groove as required for concealed pipe as directed shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. 68 supply & fixing rotational mouldedpolyethylene water storage tank white colour of capacity 500 litres ( cylindrical vertical, triple layered with closed top, isi marked ) , hoisted and fixed in position including making inlet and out let connection including dismantling / taking down of existing unserviceable pvc water storage tanks of any description and capicity with float valve and gate valve complete all as specified and as directed by engineer in charge. 69 supply and fixing ball valves, high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball ( polythene float ) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by engineer in charge.note : the minimum weight of ball valve shall be as given in ssr or in relevant is. 70 supply and fixing gun metal, globe or gate valve ( isi marked ) , with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by engineer in charge. note : the minimum weight of gate valve shall be as given in ssr or in relevant is. 71 supply and fixing in replacement bib tap with wall flange cast copper alloy, chromium plated, fancy type, long body, with round head / knob, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by engineer in charge.cat part no con 107kn of jaquar or techno commercial equivalent in make mentioned in appx b 72 supply and fixing in replacement 15 mm bore chromium plated angle stop valve with wall flange of cast copper alloy chromium plated, fancy typewith round head / knob, screwed down high pressure screwed end for iron pipe or for unions and fixed complete all as specified and as directed by engineer in charge.cat part no con 059kn of jaquar or techno commercial equivalent in make mentioned in appx b 73 supply and fixing central hole single lever basin mixer, 15mm bore, chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for whb including taking out old any type pillar cock / mixer complete all as specified and as directed by engineer in charge.cat part no vgp 81011b of jaquar or techno commercial equivalent in make mentioned in appx b 74 supply and fixing central hole basin mixer valve with regular spout, 15mm bore, brass chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for whb including taking out old any type pillar cock / mixer complete all as specified and as directed by engineer in charge. cat part no con 167knb of jaquar or techno commercial equivalent in make mentioned in appx b 75 supply and fixing in replacement mixer valve with swinging spout ( for sink ) 15mm bore, brass chromium plated, for mixing hot & cold water, screwed down for iron pipe suitable for fixing to wallcomplete all as specified and as directed by engineer in charge. cat part no con chr 309knm of jaquar or techno commercial equivalent in make mentioned in appx b 76 supply and fixing in replacement chromium plated, wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs & wall flanges, screwed ends suitable for15mm bore iron pipe, complete all as specified and as directed by engineer in charge. cat part no con 273knupr of jaquar or techno commercial equivalent in make mentioned in appx b 77 supply and fixing in replacement kitchen rack / dish rack ( kitchen stand or wall mounted ) of size750mmx600mmx250mm ( appx size ) made out of food grade stainless steel 1mm thick sheet / strip including necessary arrangements for plates and utencils to keep ( holds up to many plates or bowls to accommodate several place settings, multipurpose ) , stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories complete all as directed by engineer in charge. 78 supply & fixing in replacement stainless steel sink with drainageboard made out of 1.00mm thick sheet , kitchen or laboratory withplugs, washers, waste pipe includingbedding in cement mortar to dwarf wall or fixing cast iron cantilever brackets and connecting union to waste pipe; overall size 915mm x 460mm with bowl size 405mm x 355mm x 200mm including taking down existing chinaware sink complete all as specified and directed by engineer in charge. 79 supply & fixing in replacement vitreous china oval shape slim / thin rim ceramic wash basin, white, flat back of size 550mm x 400mm, counter top / table top including 32mm chromium plated waste coupling and pvc waste pipe including fixing material for wash basin on granite slab and including making hole in granite slab for coupling, complete all as specified and as directed by engineer in charge. 80 supply & fixing in replacement corner vitreous china wash basin, white, flat back of size 450mm x 390mm, including 32mm chromium plated waste coupling and pvc waste pipe including bracket and cutting for and pinning in end of bracket or erecting with long screwed shanks & fly nuts, flange end bedded in red lead cement, complete all as specified and as directed by engineer in charge. 81 supply & fixing in replacement 300 mm long pvc connection 15mm size with brass nuts complete all as specified & directed by engineer in charge. 82 supply & fixing in replacement 450 mm long pvc connection 15mm size with ptmt nuts complete all as specified & directed by engineer in charge. 83 supply & fixing in replacement vitreous china squatting pan orissa pattern white of size 580mmx440mm white with integral foot rests, excluding flushing cistern, flush pipe above floor but including setting the trap and pan in lime concrete ( 1 lime, 2 sand or surkhi and 5 aggretate ) , min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, including pvc flush pipe upto finished floor level, joints of flush pipe and trap make leakproof and testing upto entire satisfaction of engineer in charge before filling concrete complete all as specified and as directed by engineer in charge. 84 supply and fixing in replacement pvc low level cistern of 10 ltrs capacity with top push button inclusive of brackets and pvc bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed by engineer in charge. 85 supply & fixing in replacement cromium plated swivel shower of any colour with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of any colour for fixing with 15mm dia pipe complete all as specified and as directed by engineer in charge.note : the minimum weight 40gms. 86 supply and fixingin replacement pvc bathroom mirror cabinet of appx size 450mm x 350mm x 140mm ( compact mirror cabinet, concealed shelves ) approved quality complete all as specified and as directed by engineer in charge. 87 supply and fixingin replacement chromium plated towel ring round with round flange, fixed on wall with chromium plated brass screws and pvc plug complete all as specified and as directed by engineer in charge. cat part no acn 1121bn of jaquar or techno commercial equivalent in make mentioned in appx b 88 supply and fixingin replacement chromium plated soap dish holder with round flange, fixed on wall with chromium plated brass screws and pvc plug complete all as specified and as directed by engineer in chargecat part no acn 1131n of jaquar or techno commercial equivalent in make mentioned in appx b 89 supply and fixingin replacementcorner pvc shelf assembly fancy type with brackets, fixed with brass screws and pvc plug complete all as directed by engineer in charge. 90 taking down eaves gutters and rain water pvc / ci pipes ( any size or pattern ) including all fittings, heads, shoes, bends, swan neck etc ( measured overall as fixed along the centre line over fittings and accessories ) complete as specified and as directed by engineer in charge 91 supply & fixing 110mm bore pvc ( swr ) pipes single socketed ( pressure rating not less than 4kg / sqcm ) in any length with rubber ring joints for drain or rain water fixed along walls with and including pvc stack clamps ( interval of 1m ) of suitable size, complete all as specified and as directed by engineer in charge. 92 supply & fixing 75mm bore pvc ( swr ) pipes single socketed ( pressure rating not less than 4kg / sqcm ) in any length with rubber ring joints for drain or rain water fixed along walls with and including pvc stack clamps ( interval of 1m ) of suitable size, complete all as specified and as directed by engineer in charge. 93 supply & fixing pvc ( swr ) bends ( any radius ) suitable for 110mm bore pipe complete all as specified and as directed by engineer in charge. 94 supply & fixing pvc ( swr ) bends ( any radius ) suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 95 supply & fixing pvc ( swr ) junction single, ( single t ) equal or unequal with access door suitable for 110mm bore pipe complete all as specified and as directed by engineer in charge. 96 supply & fixing pvc ( swr ) junction single, ( single t ) equal or unequal with access door suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 97 supply & fixing pvc ( swr ) vent cowl suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 98 supply & fixing pvc ( swr ) multi floor trap including jointing with solvent cement suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 99 supply & fixing stainless steel grating 125 mm dia with or without waste hole complete all as specified and as directed by engineer in charge. 100 supply & fixing 32mm bore high density polyethylene pipes ( hdpe ) of pressure rating not less than 6kg / sqcm laid in floors / trenches complete all as specified and as directed by engineer in charge.note : ( i ) excavation, earth work if required, shall be measured & paid separately under appropriate item of this schedule. ) 101 excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc. not exceeding 10 sqm on plan and getting out in soft / loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by engineer in charge. 102 returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed. 103 removing excavated material ( surplus soil ) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by engineer in charge. 104 material and labour for pcc ( 1:4:8 ) , type d 2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by engineer in charge. 105 material and labour for pcc ( 1:2:4 ) , type b 1 using 20 mm graded stone aggregate as in coping, mud stops, packing sides / around of interlocking tiles, bed block, for embedded posts & similar work etc including weatherings, slightly roundedor chamfered angles complete all as specified and as directed by engineer in charge. 106 material and labour for providing and injecting chemical emulsion for post constructional antitermite treatment of voids in masonry using chemical emulsion@ one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand ) to match the existing floors complete all as specified and as directed by engineer in charge. 107 material and labour for providing and injecting chemical emulsion for post constructional antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre 300mm apart including drilling depth of holes not less than 300mm and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and as directed by engineer in charge. 108 taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by engineer in charge. 109 material and labour for internal plastering 15mm thick in cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the engineer in charge. 110 material and labour for rendering / plastering 15mm thick on any face of brick wall or concrete surfaces consisting in two layers i.e. first layer 10mm thick in cement mortar ( 1:4 ) and second ( top layer ) layer 5mm thick in cement mortar ( 1:4 ) including mixing of liquid wpc in mortar @ as per manufacturer instruction per bag of cement of 50kg, finished even and smooth without using extra cementcomplete all as specified and as directed by the engineer in charge. ( note : wpc shall be measured & paid separately as supply only ) 111 material and labour for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster ( 1:4 ) ( 1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster ( 1:1 / 2:2 ) ( 1 cement: 1 / 2 coarse sand : 2 stone chipping 10mm nominal size ) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete as specified and as directed by engineer in charge. note : grooves shall be measured & paid separately 112 material and labour for forming groove of uniform size 12mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as specified and as directed by engineer in charge. 113 supply only liquid water proofing compound complete all as specified and as directed by the engineer in charge. 114 dismantling of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by engineer in charge. 115 material and labour for brick work ( old serviceable bricks obtained from dismantled itemshall be reused ) straight or curved on plan exc. 6 metre mean radius built in cement mortar ( 1:6 ) complete all as specified and as directed by engineer in charge. 116 material and labour for brick work with sub class ‘b’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar ( 1:6 ) complete all as specified and as directed by engineer in charge. 117 material and labour for brick workin half brick thick wall straight or curved on plan exc. 6 metre mean radius built in cement mortar ( 1:4 ) complete all as specified and as directed by engineer in charge. 118 surface dressing not exceeding 15cm deep in soft / loose soilincluding cutting of grass, roots, bushes if any and filling of lower portion with soil obtained from cuttingafter sepration of grass, roots, bushes etc and dressing and removing from site all grass, roots and extra soil if any complete all asspecified and as directed by engineer in charge. 119 material and labour for 75mm thickcement concrete ( 1:4:8 ) , type d 2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed by engineer in charge. 120 supply and laying / fixing 60 mm thick ( m35 grade ) precast interlocking tile / paving block factory made chamfered edge ( made by using pu moulds on vibrating table machine ) using cement concrete and pigment, prepolished & preglazed, with approved colour, design & pattern as in foot parth, parks, lawns, drive ways or light traffic parking etc., laid in required colour & pattern, over and including 50mm thick compacted bed of fine sand cushining, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and complete all as specified and as directed by engineer in charge. 121 supply and laying factory made kerb stone of m 25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar ( 1:3 ) ( 1 cement:3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5mm ) , including making drainage opening wherever required complete all as specified and as directed. 122 demolition of cement concrete reinforced of any description such as slab / oht staging, kitchen chimeny, chajjas, fins, shelves, oht etc, including reinforcement cut as required to facilitate demolition and prepare the surface to casting / jointing newincluding removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge 123 material and labour for reinforced cement concrete m 25 ( design mix ) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by engineer in charge. ( note : reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. 124 material and labour for reinforced cement concrete m 25 ( design mix ) using 20mm graded stone aggregate as in louvers, parapets, railing and like complete all as specified and as directed by engineer in charge. ( note : reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. 125 material and labour for reinforced cement concrete m 25 ( design mix ) using 20mm graded stone aggregate as in chajjas, fascias, fins and like complete all as specified and as directed by engineer in charge. ( note : reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. 126 material and labour for mild steel tmt bars 10mm dia & over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified and as directed by the engineer in charge. ( note : weight of binding wire shall not be considered for measurement and payment purpose. ) 127 material and labour for mild steel tmt bars 6 to 8 mmdiacut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified and as directed by the engineer in charge. ( note : weight of binding wire shall not be considered for measurement and payment purpose. ) 128 material and labour for mild steel tmt bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required including bending, cranking etc and binding with and including ms wire ( annealed ) not less than 0.9mm dia, complete all as specified & directed by engineer in charge. ( note : weight of binding wire shall not be considered for measurement and payment purpose ) 129 form work to soffits of suspended slabs such as flat roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick ( horizontal or sloping ) rough finished complete all as specified and as directed by engineer in charge. 130 formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. vertical or to batter rough finished complete all as specified and as directed by engineer in charge. 131 form work tochullah hoods, chajjas, troughs and similar items including edgesrough finished complete all as specified and as directed by engineer in charge. 132 form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished complete all as specified and as directed by engineer in charge. 133 shotcreting average thickness 25mm in rcc columns, beams and slab etc. ( with mix minimum cement content of 350 kg per cum, m 25 ) . concrete having the specified minimum characteristic compressive strength ( with ordinary portland cement, coarse sand and graded stone aggregates of 6mm maximum size ) incl the cost of centering and shuttering at edges and corner etc as directed by engr in charge incl chipping of unsound / week concrete material 25mm average thickness from slabs, beams / columns etc with mannual chisel or standard power driven percussion type all of approved makes incl tapering of all edges, making square shoulder of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removel of rust by applying approved rust remover chemical and the coating with dr fixit epoxy zinc primer @ 6 sqm per litre at dft of 100 micron as per manufacturers instruction and specification, including removing rubbish material from building and thrown in low lying empty area at any distance from the site as directed complete as specified and as directed by engineer in charge. make : sika / fosroc / pidilite or techno commercial equivalent make approved by ge in writing from e in cs approved list.note : complete treatment to be executed by approved applicator. 134 supply and fixing hard drawn steel wire fabric not exc 4kg / sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means ofl shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding / l clip / tying with mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified and as directed. 135 material and labour for rendering 5mm thick in cement mortar ( 1:3 ) on surface of ceiling after shotcreting treatment, finished even and smooth without using extra cement complete all as specified and as directed by the engineer in charge. 136 dismantling wrought iron or mild steel work of any description complete all as specified and as directed by engineer in charge. 137 excavation in post holes in soft / loose soil n. exc 0.50 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm including removing of surplus spoil to a distance n exc 50 mtr and making good the disturbed surfaces all as specified and directed by engineer in charge. 138 material and labour for pcc ( 1:3:6 ) , type c 2 using 40 mm graded stone aggregate as in foundation filling and mass concrete, in post hole, bed block& similar work etc including form work complete all as specified and as directed by engineer in charge. 139 material and labour for mild steel framed work such as grills, ladder, cooler stand, cloth drying provision, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to fe.290.gde e 165complete all as specified and as directed by engineer in charge. 140 material and labour for structural steel work, framed work made by using rolled mild steel joist, channel, angle, or tee sections, fixed independently distance pieces, cleats or other connecting plates, gusset plates, brackets, bending and welding, riveting etc, and cut to shape, drilled and counter sunk for screw, conforming to gde fe 410 w ( gde e 250 quality a ) complete all as specified and as directed by the engineer in charge. 141 cutting out concrete blocks, slabs, brickwork or stone masonry ( in alter nate course ) , forming tooth ings for and bonding new work in mortar into old work, including new materials entering old wall ie pcc ( 1:3:6 ) type c 1 using 20mm graded stone aggregate and set in cement mortar ( 1:6 ) complete all as specified and as directed by engineer in charge. 142 supply and fixing 4mm dia galvanised iron wire fitted with nut bolts complete all as specified & directed by engineer in charge. 143 material and labour for preparation ofnew steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by engineer in charge. 144 material and labour for preparation ofnew wooden or wood based surfacesof any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by engineer in charge. 145 material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying two coats of synthetic enamel paint ( 1st quality ) of approved tint / colour to achieve glossing finish with using paint brush complete as specified and as directed by engineer in charge. 146 material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying two coats of synthetic enamel paint ( 1st quality ) of approved tint / colour to achieve glossing finish with using paint brush complete as specified and as directed by engineer in charge. 147 material and labour for preparation ofnew plastered internalwall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of acrylic emulsion of approved tint over a coat of primer by using paint brush / roller. 148 material and labour for preparation ofnew plastered external wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of exterior acrylic emulsion of approved tint over a coat of primer by using paint brush / roller. 149 material and labour for preparation ofnew plastered or concrete surface of ceiling surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) three coats of white wash by using paint brush. 150 material and labour forpreparation of old decorated surfaces ( plastered / unplastered ) of ceiling by remove / scraping down allsmoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean including applyingwall care putty where required for filling to depressions / nail holes / light cracks etc and to make surface even and smooth, and after preparing the surface smooth applying one coat of lime white wash with paint brush complete all as specified and as directed by engineer in charge. 151 material and labour for complete removal of existing treatment on old internal wall surfaces of any desciption, preperation of surface by mechanised sander having suction vaccum bag using smart periodical methodology and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface / nail holes / light cracks etc and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of acrylic emulsion of approved tint over a coat of primer on old prepared surface by using paint brush / roller.note : contractor may use manual scraping tools for complete removal and surface prepration with prior approval of engr in chrge in case of places where using of mechanical equiment are not posiible. 152 material and labour for complete removal of existing treatment on old external wall surfaces of any desciption, preperation of surface by mechanised sander having suction vaccum bag using smart periodical methodology, complete all as specified and as directed by engineer in charge and applying the following: ( a ) applying wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface / nail holes / light cracks etc and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of exterior acrylic emulsion of approved tint over a coat of acrylic emulsion external primer on old prepared surface by using paint brush / roller. note : contractor may use manual scraping tools for complete removal and surface prepration with prior approval of engr in chrge in case of places where using of mechanical equiment are not posiible. 153 material and labour forpreparation of old decorated surfaces ( plastered / unplastered ) of walls / pillars / cornices by remove / scraping down allsmoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty where required for filling to depression of scraped surface / nail holes / light cracks etc and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of acrylic emulsion of approved tint on old prepared surface by using paint brush / roller. 154 b / r portion 155 taking down carefully existing copper / aluminium point wiring ( light / fan / sockets / bell / power point ) complete with all accessories such as switch socket with sheet, ceiling rose, lamp holder including rusted / broken concealed conduit, junction and sunken boxes etc and removing dismantled material and making good disturbed surface of walls / floors etc matching with existing surface complete all as specified and as directed by engineer in charge. 156 material and labour for concealed point wiring for one light point / fan point controlled by one switch ( using red, black and green etc colour wires as colour coding ) complete with 1.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including 2mm thick galvanised steel pressed sunken terminal boxes ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switches / socket / regulator shall be measured and paid separately under appropriate item of boq / sch a ) . 157 all as per above srl item no. 156 but for onesocket out let 5 amps point controlled by one switch ( on same board ) complete all as specified and as directed by engineer in charge. ( switches, sockets etc. shall be measured and paid separately under appropriate item of boq / sch a ) . 158 all as per above srl item no. 156 but for one socket out let 5 amps point controlled by one switch ( on independent board and not below the any other switch board ) complete all as specified and as directed by engineer in charge. ( switches , sockets etc. shall be measured and paid separately under appropriate item of boq ) . 159 all as per above srl item no. 156 but for call bell point ( on independent board ) complete all as specified and as directed by engineer in charge. ( switches shall be measured and paid separately under appropriate item of boq ) . 160 material and labour for concealed point wiring for one light point controlled by two nos two way switch ( using red, black and green colour wires as colour coding ) complete with 1.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box etc, including 2mm thick galvanised steel pressed sunken terminal boxes ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switch, including provn of 1.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switches shall be measured and paid separately under appropriate item of boq ) . 161 material and labour for concealed point wiring for onesocket out let 15 / 16 amps point controlled by one switch ( on independant board ) ( using red, black and green colour wires as colour coding ) complete with 2.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, including 2mm thick galvanised steel pressed sunken terminal boxes of ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 2.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switch, socket shall be measured and paid separately under appropriate item of boq ) . 162 material and labour for concealed point wiring for onesocket out let 15 / 16 amps point controlled by one switch ( on independant board ) ( using red, black and green colour wires as colour coding ) complete with 4 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, including 2mm thick galvanised steel pressed sunken terminal boxes of ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 4 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switch, socket shall be measured and paid separately under appropriate item of boq ) . 163 taking down carefully existing copper / aluminium point wiring ( light / fan / sockets points ) complete with all accessories such as switch with sheet, ceiling rose including rusted / broken concealed sunken boxes etc but except concealed conduit and junction boxes and removing dismantled material and making good disturbed surface of walls / floors etc matching with existing surface complete all as specified and as directed by engineer in charge. 164 material and labour for concealed point wiring for one light point / fan point / bell point controlled by one switch ( using red, black and green colour wires as colour coding ) complete with 1.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through existing pvc conduit but including 2mm thick galvanised steel pressed sunken terminal boxes of suitable size ( min 60mm deep, suitable length ) concealed in wall, 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. complete all as specified and as directed. ( switches, regulator shall be measured and paid separately under appropriate item of boq ) . note: where ever it is not feasible to cable drawn through existing pvc conduit in roof salb ( for ceiling fan point only ) due to blocked, casing caping shall be provided by contractor without any extra cost, cost for the same shall deemed to be included in the quoted unit rate. 165 supply and fixing switch piano flush type ( isi marked ) , 5 / 6amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by engineer in charge. note ; laminated sheet shall be measured and paid in point wiring item of boq. 166 supply and fixing switch piano flush type ( isi marked ) , 5 / 6amps, single pole, two way fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet and covering frame shall be includedin point wiring item of boq ) . 167 supply and fixing switch piano flush type ( isi marked ) , bell push, 5amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 168 supply and fixing socket outlet multipurpose type ( isi marked ) , 2 in 1, 5 pin, 5 / 6 amp, flush type fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 169 supply and fixing socket outlet multipurpose type ( isi marked ) , 2 in 1, 6 / 5 pin, 6 amp and 16 amp, flush type fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 170 supply and fixing switch piano flush type ( isi marked ) , 15 / 16amps, single pole, one way complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 171 supply and fixing ceiling rose ( isi marked ) surface type polycarbonate isolated body three terminal, topline series 65x50mm, 6 amp, complete all as specified and as directed by engineer in charge. 172 supply and fixing angle lamp holder ( isi marked ) polycarbonate cased body ( b22 base ) , top line series, with back plate, 6amps, complete all as specified and directed by engineer in charge. 173 supply and fixingelectric calling bell ding dong type, ac 230 volts single pole including making elctric connection and testing, complete all as specified and as directed by engr in charge. 174 supply and fixing mcb ‘b’ curve suitable for 240 volts ac supply, 06 to 32 amps, sp with over load and short circuit protection and rupturing capacity not less than 10 ka, fixing in db / panel complete all as specified and as directed by engineer in charge 175 supply and fixing mcb ‘b’ curve suitable for 240 volts ac supply, 32 40 amps, spn with over load and short circuit protection and rupturing capacity not less than 10 ka, fixing in db / panel complete all as specified and as directed by engineer in charge 176 supply and fixing in replacement ( concealed flush to wall ) factory made db ( made out of crca sheet not less than 1.2mm thick, fitted with din channel neutral link and 200 amp rated bus bar ) spn, 12 way 240v, suitable for mounting mcb / isolator, conforming to is 13032, db shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. the db shall be double door type with hinged door with locking arrangement, the dbs shall be same make as mcbs, db shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. the dbs shall be of ip 43 protection class, including taking down unserviceable old db any type including mcb etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by engineer in charge.note : mcb’s shall be measured and paid separately under appropriate item of boq. 177 supply and fixing in replacement of led complete fitting including batten, t 8 retro led polycarbonate 1 x 20watt, appx 4 feet long, with decorative ultra ceiling square profile linear led lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23 / 0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts. ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.95 ( e ) thd : max10%. ( f ) ip rating : ip 20. ( g ) crca pre coated housing with two coloured plastic end cap. ( h ) led driver of the same make as of the luminaire. ( j ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( k ) surge protection minimum 2.5 kv. ( l ) cct : minimum 6000k ( m ) cri : minimum 80 ( n ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 178 supply and fixingin replacement led light fitting 1 x 10watt, appx 2 feet long with decorative ultra ceiling square profile linear led lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23 / 0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.95 ( e ) thd : max 10%. ( f ) ip rating : ip 20. ( g ) crca pre coated housing with two coloured plastic end cap. ( h ) led driver of the same make as of the luminaire. ( j ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( k ) surge protection minimum 2.5 kv. ( l ) cct : minimum 6000k ( m ) cri : minimum 80 ( n ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 179 supply and fixing in replacement of led bulkhead fitting 1 x 10watt, complete with standard profile linear led lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23 / 0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 50°c ( d ) power factor : minimum 0.95 ( e ) thd : max 10%. ( f ) ip rating : ip 65. ( g ) cct : 6500k ( h ) impact resistant polycarbonate housing, polycarbonate diffuser with silicon gasket ( j ) led driver of the same make as of the luminaire. ( k ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( l ) surge protection minimum 2.5 kv. ( m ) cri : minimum 80 ( n ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 180 supply and fixing in replacement led lamp minimum 3 star rated 9 / 10 w led b 22 base complete all as specified and directed by engr in charge with following specifications ( a ) lumen system efficacy of lamp should be minimum 100 lumen per watt. ( b ) input voltage range : 160 to 270 volts ( c ) temp operating range : minus 10°c to plus 50°c ( d ) power factor : minimum 0.90 ( e ) cri: minimum80 181 supply and fixing in replacement energy efficient led security light fitting of 25w pressure die cast aluminium housing / body, heat resistant clear toughened glass, better optics for uniform distribution street luminaire, with driver, including electric connection, fixing the light fitting with existing bracket and clamps but including repalcement of nut bolts if required, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting with old bracket any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 50°c ( d ) power factor : minimum 0.95 ( e ) thd : max10%. ( f ) ip rating : ip66. ( g ) ik rating:minimum ik07 ( h ) built in potted led driver of the make as of the luminaire. ( j ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( k ) surge protection 10 kv ( inbuilt + extended ) ( l ) cct : 5700 k. ( m ) cri: minimum 70 ( n ) lens high efficiency wide angle lens. ( o ) bis approved fixtures and driver ( p ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 182 supply and hanging / fixing ceiling fan 1200 mm sweep ac supply ( input voltage range ; 120 to280v ) , bldc type, 5 star rated, bee and isi marked super enamelled, copper winding of b class insulation, single phase, minimum 30w ( ± 10% ) , temperature rise 40 degree maximum without remote but with and including capacitive regulator, 03 no blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable sizefrom ceiling rose to fan complete all as specified.note : ( i ) serial number as issued by engr in charge of celing fan and ge office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account 183 supply and fixing exhaust fan ( heavy duty ) steel body, ac single phase 230v, 50 cycle per second, size 300mm sweep with blades and frame including self closing gi louvers off mode protection against birds etc mounted in suitable opening arrangement. including electric connection with and including new flexible sheathed copper wire of size 24 / 0.2mm, 3 core from ceiling rose to fan ( not exceeding 0.5 mtr long ) , and hanging on wall with 4 nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by engineer in charge.note : serial number of exhaust fan issued by engr in charge and ge office name shall also be written on fan with red colour permanent marker. 184 supply and fixing ventilating air fresher fan of size 250mm sweep, single phase, 1200rpm, copper winding, made of sturdy engineering plastic complete with louvers shutter, including provision of cutting of wall for suitable opening as per fan and making good the disturbed surface as per existing, including electric connection with suitable flexible copper cable from ceiling rose to fan complete all as specified and as directed by engineer in charge. 185 material and labour for concealed sub main wiring ( two run for main i.e. phase and netural and one run for continues as earth wire connected to earth dolly etc., using red, black and green colour wires as colour coding ) with 6 sqmm single core, frlsh pvc insulated multistrand copper conductor drawn through and including pvc conduit 25mm dia ( medium quality isi marked ) , on independent circuit from db including all fitting arrangement i.e. pvc clamp, rawl plug, screw, terminal / junction box, tee, bend etc. and including cutting of chases in wall, taking out old sub main wiring of any conductor any sizefrom conduit and taking down old unserviceable conduit with fittings, and making good disturbed surfaces of walls as per original complete all as specified and as directed by engineer in charge.note : three run of 6 sqmm copper wire and one run conduit shall be measured as one rm length for payment. 186 supply, installation, commissioning and testing of factory made lt panel board ( main control board ) of minimum size 100cm x 80cm x 25cm fixed on / inside wall ( front side open able, double glass door including locking arrangements and handle ) , dust proof, vermin proof made out of crca sheet 2 mm thick powder coated, suitable arrangement for fixing electronic energy meter 04 nos, including pre wired internal wiring with & including single core, pvc copper conductor unsheathed wire multistanded 6 sqmm including provision of rubber beading and mild steel cable glands and lugs, provision of air fins for ventilation, including comprising of 01 no mccb 100amps fp 16ka 415v for incoming, 04 nos mcb 40amps spn for outgoing, 01 no mcb 10 amps spn for outgoing and copper bus bar 200amps for 3 phase and netural complete including all connections incoming / out going, including taking down old panel board any type with fittings complete all as directed by engineer in charge.note : cost for fixing of old electronic meter after taking out from old panel board shall deemed to be included. 187 supply and fixing electric water heater ( geyser ) storage type abs body of capacity 25 ltrs, 5 star rating, 230v, single phase ac supply, inner tank made out of heavy duty stainless steel sheet ( designed with single weld line, factory tested with hydraulic pressure as per latest is code ) with glass lined coating complete with all accessories such as safety valve, thermostate, nrv, connection piece, pvc connection for hot and cold water, three core pvc insulated pvc sheathed copper conductor flexible cable including 15amp plug suitable for existing socket, including 04 no nut bolts etc for hanging of geyser. nut bolt grouting in wall in pcc ( 1:2:4 ) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and as directed by engineer in charge. 188 material and labour for earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including giearthing wire 4 mm dia by means of gi bolts / nuts / washers and protected by 15 mm bore gi medium grade pipe upto test point or upto main switch board, fixing with 02 nos nuts and bolts. earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common saltall around bottom and top. 20 mmbore gi medium grade pipe for watering and including funnel, wire mesh, pcc chamber pit made with pcc ( 1:3:6 ) type c1 ( using 20 mm graded stone aggregate ) including necessary form work, excavation and earth work in any type ofsoil, returning filling and disposal of surplus soil to a distance not exceeding 50m, pit cover 40mm thick made with rcc ( 1:2:4 ) type b1 ( using 20 mm graded stone aggregate ) including tmt reinforcement 8mm dia @ 75mm c / c both way, ms handle 12mm dia, cover rest on ms angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer, complete all as specified & shown in electrical plate no. 3 ofssr 2009 ( part i ) including taking out / dismantling old unserviceable earthing system complete all as specified and as directed by engineer in charge.note: ( i ) pcc chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. ( ii ) protection pipe and gi earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. ( iii ) the earth testing arrangement should be done by the contractor as per direction of engineer in charge. 189 supply and laying or fixing or laid in trenches / ducts / through pipes / in floors / under roads / under hard standing / along poles and testing, cross linked polyethylene ( xlpe ) lt cable, xlpe insulated, pvc inner sheathed, bedded, galvanised steel strip or wire armoured cable ( heavy duty ) 1100 volt gradewith stranded aluminium conductor having cross sectional area 35 sqmm3.5 core conforming to is 7098 ( part i ) 1988 with upto date amendments, including taking out old unserviceable cable any size complete allas specified and as directed.note : ( i ) excavation, earth work, sand cushioning, brick protection, boring / cutting of road and pipe shall be measured & paid separately under appropriate item of this schedule. ) 190 material and labour for sand cushioning, with dry and clean fine river sand ( for under ground cable ) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed. ( note: punned thickness shall be considered for payment purpose ) 191 supply and laying un reinforced precast concrete cable cover, class lv, type 2 flat, size 300mm x 180mm x 40mm for cable protection cover, laid dry in trenches over the cable , perpendicular to the direction of cable complete allas specified and as directed. 192 supply and fixing in replacement gi tubing light grade of size 50 mm bore, isi marked, fixed along poles / walls or laid in trenches, under road for cable protection including fittings ( elbow, tee, socket etc ) complete all as specified and as directed. ( note: excavation and earthwork as required shall be measured and paid separately under respective item of sch. ) 193 material and labour for cutting of road / floor etc any type upto 45cm width and depth for laying of cable / pipe, after laying of cable / pipe returning filling with soil including spreading, leveling watering and well ramming in layers upto 30cm and top layer 15cm thick filling by using pcc ( 1:3:6 ) type c2 using 40mm graded stone aggregate to match the existing level of road / floor complete all as specified and as directed. 194 boring of holes under road, pavement, hardstanding by using trenchless boring machine or by manual manpower suitable for inserting gi pipe any dia upto 50mm including removal of surplus soil and making good disturbed surface complete all as specified and as directed.note: pipe for inserting as required shall be measured and paid for separately. 195 material and labour for extra wiring for inverter socket out going to db with 1.5 sqmm single core, frlsh pvc ( using colour coding as directed ) insulated multistrand copper conductor drawn through existing conduit ( conduit for point wiring already catered in point wiring item of boq ) including making connection to db and inverter socket ) complete all as specified and as directed by engineer in charge. 196 supply and fixing plug top 5 / 6amp 3 pin good quality suitable for 240 volts, ac supply for inverter socket complete all as specified and as directed by engineer in charge. 197 supply and fixing socket outlet flush type ( isi marked ) , 25amps ( for inverter point ) , fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) ....

Military Engineer Services - Punjab

35373251 tender for provision of mob equipment stores for medical regt ( fd regt ) and rewiring of bldg no. p 67 ( 12 qtrs ) or md accn of engr regt at 550 acre under ge ( east ) ferozepur cantt / r workexcavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, for lying cables etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft loose soil complete all as specified and as directed. 2 m&l cement concrete in foundations 1:4:8 type d 2, ( 40mm graded stone aggregate as in sub base of foundation, filling and mass concrete complete all as specified and as directed. 3 m&l for brickwork with subclass ‘b’ bricks, straight or curved on plan exc 6m mean radius built in cm ( 1:6 ) complete all as specified and as directed. 4 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm soft / loose soil complete all as specified and as directed. 5 removing excavated material / soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 6 use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter rough finishedsurface of concrete complete all as specified and as directed. 7 use and waste of formwork to sides of pillars, posts, struts, piers, columns etc rough finishedsurface of concreteall as complete all as specified and as directed. 8 use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) rough finishedsurface of concrete complete all as specified and as directed. 9 use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm widerough finishedsurface of concretecomplete all as specified and as directed. 10 use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finishedsurface of concretecomplete all as specified and as directed. 11 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed. 12 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) columns, pillars, piers, posts and struts complete all as specified and as directed. 13 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. 14 m&l rcc design mix m 25 ( 20mm graded stone aggregate ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. 15 m&l mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 16 all as per item no 15 above but 5mm dia and over upto and incl 10mm dia in stirupps, spacers and binders etc complete all as specified and as directed. 17 m&l rendering 12mm thickin cement mortar ( 1:4 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed. 18 m&l rendering 15mm thickin cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed. 19 m&lrendering 10 mm thick cement plaster on ceiling surfaces in cement mortar 1:4 finished fair and evenwithout using extra cement complete all as specified and as directed. 20 supply only integral water proofing compound conforming is 2645 1975 of approved make complete all as specified and as directed. 21 m&l preparation of newly plastered surfaces of walls etc, and applying three coats of white wash complete all as specified and as directed. 22 m&l preparation of new plastered surfaces of ceiling & applying two coats of white wash complete all as specified and as directed. 23 m&l applying double coats of bitumen elastometric waterproof coating as on damp proof course / roof including cleaning of surfaces complete all as specified and as directed. 24 m&l 75mm thick cement concrete 1:4:8 type c 2, using 40mm graded brick aggregate as in sub floor, sub base etc, finishing surfaces rough to receive the topping layer all as complete all as specified and as directed. 25 m & l machine pressed precast conctete interlocking paver block any shape and size confirming to is 15658 2006 of 60 mm thickness m 35 grade, jointed and pointed with gray cement and no pigment over sand cushioning complete all as specified and directed. 26 m & l sand filling under floors or in foundations including watering and consolidationcomplete all as directed by engieer in charge . 27 m&l 75mm thick cement concrete ( 1:3:6 ) type c 1 using 20mm graded stone aggregate as in plinth protection, surfaces finished even and fair without using extra cementincluding provision of construction joints complete all as specified and as directed. 28 m&l 75 mm thick cement concrete ( 1:2:4 ) type b 2 using 40mm graded stone aggregate as in floor topping, surface finished even and smooth without using extra cement complete all as specified and as directed. 29 m&l glass dividing strips, 3 mm thick and 38mm width of strip, inserted in position, conform to design complete all as specified and as directed. 30 s&f pressed steel frames ( 1.25mm sheet thickness ) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mmincluding one shop coat of red oxide primer complete all as specified and as directed. 31 s&f of 40mm thick flush door shutter of solid core construction with particle board core and plywood face panels, commercial type on both sides one face is covered with decorative face veneerwith lipping / frame to match complete all as specified and as directed. 32 s&f factory made box type steel window with pintal hinges & 2 nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing no cejz / td 06 / 07 & cejz / td 07 / 07. 33 s&f factory made box type steel window with pintal hinges & 2 nos 150 mm mild steel tower bolts to each shutter, steel handle and withoutglazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing no cejz / td 06 / 07 & cejz / td 07 / 07. 34 s&f steel ventilators fixed type complete with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and as directed. 35 mild steel framed work of e 165 ( fe 290 ) as in grills / guard bars shouldered with steel window / ventilator frames including red oxide primer coat complete all as specified and as directed. 36 s&f mild steel door handles, stove enameled black, medium wt 125 mm long and fixed with steel screws complete all as specified and as directed. 37 s&f mild steel barrel tower bolts, stove enameled black, with bright bolt, medium weight 150 mm long and fixed with steel screws complete all as specified and as directed. 38 s&f 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified and as directed. 39 s&f 3 mm thick, plainsheet glass ordinary quality and glazing, with oil putty or with wooden beads ( supplied alongwith shutters ) , in squares n.exc 0.50 sqm complete all as specified and as directed. 40 s&f stainless steel wire cloth0.56 mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staplescomplete all as specified and as directed. 41 m&l cement concrete ( 1:3:6 ) type c 1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc, complete all as specified and as directed. 42 m&l preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed. 43 m&l preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and as directed. 44 m&l preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paintcomplete all as specified and as directed. 45 e / m worksm&l for point wiring with 1.5 sqmm ( nominal area ) , pvc insulated, frls multistranded, single core unsheathed, copper conductor cables drawnthrough and including pvc conduit with allaccessories concealled in wall and fixed to ceiling etc. with and including 1.5 sqmm ( nominal area ) pvc insulated, frls unsheathed, multi stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth dolly including sunken boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for mounting switches, sockets, regulators etc complete for one light / fan / bell point controlled by one , one way switch all as specified and directed. ( a ) one light point / fan point / exhaust point controlled by one single pole one way switch. ( note: wiring shall be done in colour coding ) 46 all as per item no 45 hereinbefore butone 3 pin socket outlet 5 amps independent boardcomplete all as specified and as directed. 47 all as per item no 45 hereinbefore but one 3 pin socket outlet 5amps on the same board with other switches complete all as specified and as directed. 48 all as per item no. 45 here in before but one 15 amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 sqmm pvc insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 2.5 sqmm green colours pvc insulated, unsheathed, stranded copper conductor cable. 49 all as per item no. 45 here in before but one 15 amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 sqmm pvc insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 4.0 sqmm green colours pvc insulated, unsheathed, stranded copper conductor cable. 50 s&f switch piano flush type 6 amps, single pole one way, white in colour, duly isi marked complete all as specified and directed. 51 s&f switch piano flush type 20 amps, single pole one way, white in colour, duly isi marked complete all as specified and directed. 52 s&f socket outlet2 in 1, 5 pin, 6 amps, white in colour, duly isi marked complete all as specified and directed. 53 s&f socket outlet, uni, 2 in one10 amps & 20 amps, white in colour, duly isi markedcomplete all as specified and directed. 54 s&f ceiling rose surface type, 240 volts, 50 hz, 6a, pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals dulyisi marked complete all as specified and directed. 55 s&f rotary stepped type electronic fan regulator for ceiling fan 1200 / 1400mm size, 240 volts, 6 amps, 100w, white in colour, duly isi marked complete all as specified. 56 s&f lamp angle holder ( plastic ring ) , 240 volts, 50 hz, 6a, white in colour, duly isi marked complete all as specified and directed. 57 s&f led bulb of 9 watt, b22, 6500k all as specified and directed. 58 s&f 20w, 6500 k, 4 feet led square tube light fitting, energy efficient fixed to wall / ceiling etc complete all as specified and as directed. 59 s&f led sleeky bldg street light ( lens ) fitting of 35 watts, 6000k, including gi bracket bend to shape made out of gi pipe light grade of 25 mm, size up to 1.2 mtr long etc complete with ms clamps made of 25x3mm ms plate, duly painted with two coats of aluminium paint with nuts / bolts / washers and all fixing arrangements to wall / pole, including connecting up with 2 core copper flexible wire of size 23 / 00.0076 complete all as specified and as directed. 60 s&f exhaust fan heavy duty with louvers complete of sweep size 300mm, 900 rpm, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of pvc flexible copper cable of size 23 / 00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and as directed. 61 s&f ceiling fan 1200mm sweep, ac single phase 230 volts 50hz, at bldgs upto 5 mtrs height, including provision of flexible cable 3 core copper conductor of size 23 / 0.0076 of suitable length from ceiling rose to ceiling fan upto 1.5 mtr for giving connection and all hanging arrangement i.e. standard down rod, hanging clamp, with rubber real nuts bolts, spring washers and locking of splite pin, plastic canopy with screw compete without fan regulator and marking of mes nos with black synthetic enameled paint all as specified and as directed. 62 s&f factory made sheet metal enclosures double door type made out of crca 1.2 mm thick m.s. sheet, powder coated, partly embedded in wall, ip 43 protection, vtpn db with 200 amps rated bus bar, 4 way, 415 volts, vertical type, dust and vermin proof, suitable for incorporation of mccbs / mcbs, factory made, including thermal based release adjustable type 4 pole 63 amps, 50 hz, 415 volts with rupturing capacity 16 ka and making good distrubbed surfaces with matching colour, complete all as specified and as directed. 63 s&f factory made sheet metal enclosures double door type made out of crca1.2 mm thick m.s sheet, powder coated, spn db with 200 amps rated bus bar, 8 way, ip 42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of mcbs duly cocealled in wall, factory made, including making good distrubbed surfaces with matching colour complete all as specified and as directed. 64 s&f mcb spn, 40 amps, 240 volts, b series, 10ka duly isi marked, complete all as specified and as directed. 65 s&f mcb sp, 6a 32 amps, 240 volts, b series, 10ka duly isi marked, complete all as specified and as directed. 66 m&l for sub main wiring with two single core 2x4 sqmm pvc insulated and unsheathed stranded copper conductoralongwith earth wire 4.0 sqmm drawn in including pvc rigid conduit connected to main board complete all as specified and directed ( note: two runs cable and one number earth wire and suitablepvc conduit shall measured together as unit length ) . 67 m&l for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanised iron or steel wire complete all as specified and as directed. 68 m&l for earthing complete with galvanized steel plate elecrode of size60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead gi wire of 4mm dia ( 8 swg ) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. the other end of gi earth wire is connected to main switch board and protected by light grade gi pipe of 15 mm bore. provision of 20mm bore light grade gi pipe for watering including gi funnel and wire mesh. pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. cement concrete chamber of pcc ( 1:3:6 ) type c 2 using 40 mm graded stone aggregate.the chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate and ms angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in electrical plate no 3 of ssr part 1 ( 2009 ) . 69 supplying, laying, jointing and testing xlpe insulated, armoured, electric cables ( heavy duty ) with aluminium conductor, 1100 volts, grade cross sectional area 25 sqmm 4 core confirming to is:7098 1985 laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and as directed. ( note: excavation & earth work, cable preotection coverand sand cushion shall be measured &separately ) 70 m&l dry and clean fine sand for cable cushioningto underground cable protection, complete all as specified and as directed. note punned down thickness shall be measured. 71 s&f cover to underground cable with one layer of bricks using sub class ‘b’ bricks ( old size ) laid flat across the cable complete all as specified and as directed. 72 s&f mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles / walls, laid under floor / road crossings, complete with and includingclamps socket & elbow etc complete all as specified and as directed. 73 taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5 / 15 amp points complete withfitting and fixtures such as switches, sockets, c / rosess, holders and bracket fittings with battens / conduits / wires, t / l fittings and making good the disturbed surfacesof walls and roofs etc.and to match with existing colour complete all as specified and directed. 74 taking down carefully unserviceable main switches and distribution boards with fuses / mcbs ( single phase or three phase ) of any capacity complete all as specified and as directed. 75 taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified 76 s&f bell push flush, type 6 amp single pole one way, white in colour, duly isi marked complete all as specified and as directed. 77 s&f door bell ding dong single phase 240 volts, white in colour, duly isi marked complete all as specified and as directed. 78 s&f batten holder ( with metal ring ) , 240 volts, 50 hz, 6a, white in colour, duly isi marked complete all as specified and as directed. 79 s&f factory made three phase and neutral sheet steel made out of crca 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing mcbs and the second for protection of mcbs fitted with colour bus bar of capacity 200 amps, neutral link, earth bar and din rail suitable for use on 240 / 415v, 50hz supply, vtpn db, partly immersed in wall, including of mccb 4 pole adjustable thermal & fixed magnetic type 100 amps, 50hz, 415 volts with rupturing capacity 16 ka and making good distrubbed surfaces with matching colour, complete all as specified and as directed. 80 s&f mcb spn, 40a 63amps, 240 volts, c series, 10ka duly isi marked, in mcb db, complete with connection testing and commissioning complete all as specified and as directed. 81 m&l for sub main wiring with two single core 2x6 sqmm frls insulated and unsheathed stranded copper conductoralongwith earth wire 6.0 sqmm frls drawn in includingrigid conduit connected to main board complete all as specified and directed ( note: two runs cable and one number earth wire and suitableconduit shall measured together as unit length ) . 82 cutting holes making good the distributed surface, grouting nuts for fixing of exhaust fans complete all as specified and directed. 83 m&l for disconnecting electric meter of any cap and refixing same after rewiring, in meter box including connection complete all as specified and as directed. 84 s&f sheet metal meter box single door minimum size 35x50x25cm for electric meter factory made of ms sheets / crca sheet duly painted with powder paint and door hinged locking arrangement conforming to is 5039 of 1983. the electric meter / switch box shall be suitable for fixing one number of electric meter and knock out holes for incoming and outgoing cable. before the powder paint process the sheet steel shall go through the anti corrosion conditioning process in not less than seven tank process. concealed in wall, including making good distrurbed surfaces with matching colour, complete all as specified and as directed. 85 fixing or hanging only ceiling fans height upto 3mtr to 5 mtrs ceiling height of bldg including three core fr pvc insulated & overall round sheathed flexible with pvc, colour of cores are red, black & yellow / green is for earthing. sheath colour is black of cable size 23 / 0.0076 complete all as specified. ( note : ceiling fans obtained / taking down from item sr no.73 as above ) ...

Public Works Department - Punjab

35361843 providing and installation of furniture in various health clinics/aam adami clinic (aacs) in distt. jalandhar (cd dakoha, uphc dhanowali, phc jamsher khas, phc raipur pharala, cd nagra, uphc maqsudan, usad gandhi nagar, uphc basti bawa khel, uphc bha , i) providing & installation of furniture , chair for reception providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load.the seat size shall be 460±10 mm(w) x 450±10 mm(d) and back size shall be 460±10 mm(w) x 400±10 mm(h) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. , waiting area chair 3 seater supplying & placing three seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 60? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm(d) x 405±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm. , waiting area chair 2 seater supplying & placing two seater bench. the seat and back shall be made up of high quality cold rolled ms perforated sheet of 1.2mm thick, pressed and welded to form the shape. the seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. the armrest shall be made up of mild steel powder coated tube with 1.2mm thick. the base structure shall be supported by ms powder coated with 40 50? (dft). there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 450±10 mm(d) x 430±10 mm(h) from ground. overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm. , doctor table supplying & placing executive table with credenza unit in completely knock down conditions with an overall size 1600mm x 1600mm x 750mm that is to be assembled at site. the worktop shall have the size 1950mm x 900mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. the table shall be clad with 1mm thick modesty panel which provide structural support for the table. it should be 1mm thick with star perforation crca powder coated sheet in linear shape. the understructure shall consist of loop leg and c type leg made up of crca powder coated triangular shape pipe having cross section area 53mm x 53mm x 75mm with 1.6mm thick. there shall be shoe provided at the base to avoid scratches on the floor. side top shall be provided with an overall size 800mm x 500mm x 750mm made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish. 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. it shall be supported on peg which is mounted on credenza unit. the credenza unit shall have overall size 1400mm x 575mm x 500mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have 2 box drawer, 1 filing drawer and 1 shutter. the drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the shutter shall be operated by ss handle and concealed crank hinge. the credenza unit shall be mounted over crca powder coated u shape leg having cross section area 53mm x 53mm x 75mm with 1.6mm thick. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. , main chair for doctor providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40kg/m³ in back. the seat and back shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standards. the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi/bifma standards x5.1 2011 tested to perform 98,000 cycles with 250lbs load. the seat size shall be 470±10 mm(w) x 460±10 mm(d) and back size shall be 460±10 mm(w) x 610±10 mm(h) from seat & overall height = 1050±10 mm. , visitor chair for doctor providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. the same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 gsm. the seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. the seat and back shall be arrested together with 50 60? thick powder coated hr steel spine. the armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. the frame structure shall be cantilever support type made up of ms crca powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor . the seat size shall be 480±10 mm(w) x 450±10 mm(d) and back size shall be 480±10 mm(w) x 400±10 mm(h) from seat & overall height = 820±10mm, overall depth = 600±10 mm. , examination table for doctor room providing and placing in position examination table. overall size of the table shall be 1830 mm l x 560 600 mm d x 810 850 mm h. the examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick m.s. erw tube. nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. lying surface shall be made of 1.2 mm thick m.s. erw tube. ratchet shall be made of 5 mm thick m.s. erw tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. it shall be provided with 30 mm thick mattress. the bed should be provided with 40 density 30mm thick pu foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & x ray permeable. the zip & stiches for the mattress cover should be concealed. complete as per sample approved by architect & desired by engineer in charge. , chair for pharmacist supplying and placing ergonomically designed, comfortable & aesthetically appealing mid back chair. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. the same shall be upholstered with leatherite tapestry 0.8mm thick and 535 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine. moulded pp arm shall be used with cushion and leatherite upholstery. for seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suite them using the lever under the seat. the gas lift mechanism should be tested as per ansi/bifma x5.1 2011 standard. the pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi/bifma x5.1 2011 standard tested to perform 98,000 cycles with 250lbs load. the seat size shall be 515±10mm(w) x 490±10mm(d) and back size shall be 510±10 (w) x 510±10mm(h) from seat & overall height = 945±10mm. , stool for doctor, pharmacist room & in samplingroom revolving stool, ss top, powder coated, height adjustable (510mm 690mm). complete as per sample approved by architect & desired by engineer in charge. , storage for medicine providing, supplying and placing steel almirah. the overall size of the almirah shall be 915mm (w) x 485mm (d) x 1980mm (h). the almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading compartments.the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity andhigh load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50? thick. , customized lab table supplying & placing storage unit with an overall size 1800mm x 600mm x 900mm. it should be made up of 18mm thick ply 710 grade bwp (century/ green ply / black cobra or equivalent. 1mm thick (green lam / sunmica / century ) mica pasted on the ply on outer side frunished with malamine polish and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. the sliding shutter shall be operated on sliding rail track and ss handle as well as push lock mechanism. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. , providing and placing moveable 3 fold screen of ms fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. the overall dimension of the 3 fold screen will be 1675mmx2450mm around examination table. the ms frame will be powder coated in colour as complete as per sample approved by architect & desired by engineer in charge. , providing and fixing roller blinds at the designated locations with fabric/ texture complete as per sample approved by architect & desired by engineer in charge. , provding and placing of steps for examination table in doctor room approved by the architect/ engineer in charge...

Military Engineer Services - Punjab

34955759 tender for day to day maintenance under age b / r ii, ge gurdaspur. taking down shutters of any descriptionexc 1.00 sqm & nexc 2 sqm each. & refixing in the same opening after rectify the defect. 2 repairs, easing & and adjusting without taking down shutters of any description not exc 1.00 sqm each complete all as specified and directed. 3 s&f in repair beads, straight ( any size ) of second class hard wood for glazed or gauged joinery, renewed , including mitres etc. complete all as specified and directed. 4 s&f in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, fixed with stainless steel wire staples all as specified and directed. 5 s&f 3mm sheet glass ordinary quality and glazing with oil putting in squares n.exc 0.50 sqm each complete all as specified and directed. 6 s&f 3mm thick figured glass sheet fixed with beads or oil putty in squares n.exc 0.50 sqm eachcomplete all as specified and directed. 7 m&l in repair for block boards, 18 / 19mm thick, grade 1 quality, exterior grade, decorative type with decorative face veneer on both faces, fixed with screws to timber frame work for built in cup board shelves / partitions and kitchen cb, shutters etc complete all as specified and directed. complete all as specified and directed. 8 m&l external teak wood lipping, 6mm thick to 19 / 20 mm thick block board or veneered partical board, fixed with nails including french polish two coats complete all as specified and directed. 9 s&f in repairs ms peg set of six powder coated complete all as specified. 10 s&f in repair 40mm dia cupboard knobs of mild steel, bright finish, fixed with nut, screw and washer all as specified and directed. 11 s&f in repair 100mm sizehasp and staple mild steel safety type stove enameled black including bolt to hinge plate and fixed with screw all as specified and directed. 12 s&f sheet glass shelf assembly consistng of 5.5mm thick sheet glass shelf 12cm wide with aluminum alloy bracket and guard railing 60 cm long complete all as specified and directed. 13 m&l for petty repair to existing in built wooden cup board shutter, locks, hinges including necessary welding and making the lock / wooden cup boards complete serviceable all as per existing pattern as directed by engineer in charge including provision of duplicate keys as required. 14 m&l for petty repair to existing steel window shutter by welding hinges or removing the steel window shutters from the frame and re fixing after making serviceable including painting two coats synthetic enamel paint over a coat of red oxide primer on repaired surface all as specified 15 s&f in repair aluminium alloy handles fabricated type size 125mm complete all as specified and directed. 16 s&f in repair ms butt hinges 100mm size medium weight cold rolled mild steel complete all as specified and directed. 17 s&f in repair ms butt hinges 75mm size medium weight cold rolled mild steel complete all as specified and directed. 18 s&f in repair 300mm long aluminum alloy anodized sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed all as specified and directed. 19 s&f 150mm long aluminum anodized barrel tower bolt of extruded section and fixed all as specified. 20 s&f in repair 150mm ( overall length of cover plate ) floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and directed. 21 s&f in repair 300mm mild steel ordinary rat tail rod pattern spring including roller plate complete all as specified and directed. 22 supply and fix in repair for aluminium ( die cast ) body door closer hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed 23 s&f in repairs stainless steel grating 100mm dia. complete all as specified 24 s&f in repair stainless steel curtain rod 25mm dia rod with bracket, nobetc complete all as specified and directed. 25 s&f in repair sink with drainage board made of stainless steel 1mm thick with plug washer and waste including fixing cantilever brackets and connecting union to pipe over all size 915mmx460mm bowel size 410mmx330mmx160mm complete all as specified and directed. 26 s&f in repair stainless steel plate rack size 75cmx75cmx 25cm & fixed to wall complete all as specified and directed. 27 s&f rotational moulded polyethelene, triple layers, white water storage tank 500 ltrs capacity, closed top, cylindrical, hoisted closed top hoisted and fixed in position with 20mm bore ptmt ball valve epoxy coated minimum weight 210 gms with aluminium rod including dismantling existing water tanks complete all as specified and directed. 28 all as per srl item no 27 above but 1000 ltrs capacity. 29 s&f in repairs pvc cover with fitting of pvc water tanks of capacity exc 250 litre but not exc 1000 litre complete all as specified. 30 cleaning and removing all scale and dirt etc from over head water tanks and mouth of circulating pipe etc of capacity exc 250 litres but not exceeding 500 litres using bleaching & refixing in the same position complete all as specified and directed. 31 cleaning and removing all scale and dirt etc from over head water tanks and mouth of circulating pipe etc of capacity exc 500 litres but not exceeding 1000 litres using bleaching & refixing in the same position complete all as specified and directed. 32 s&f in repairs kitchen sink coupling stainless steel 75 mm to 100mm dia, including pvc waste pipe of suitable length complete all as specified & directed. 33 s&f in repairs 32mm dia. pvc waste pipe for urinal / whb / sink fixed complete all as specified & directed 34 s&f in repair brass cp waste coupling 32 / 40mm dia for whb / urinal complete ( half and full threaded ) 35 supply and fix in repair vitreous china half stall type urinal, white, including providing and fixing plugs, bedding urinal against wall in cement mortar ( 1:2 ) , securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement paste, 32mm dia pvc flush pipe and discharge pipe, grating and union for discharge pipe complete all as specified and as directed. 36 all as per srl item no 35 above but vitreous china urinal bowl, flat back size 465x365x265mm white, with grating & union for discharch pipe etc. 37 s&f in repair new brass spindle with nylon washer and removing leakage of water of any bib tap / stop valve suitable for 15 to 20mm bore pipe complete all as specified. 38 taking up or down 15mm dia steel tubing and connections all as specified and directed. 39 fixing only 15mm dia steel tubing and connection in new or old position including all fittings, cleaning ( in wall ceiling floors etc ) all as specified and directed. 40 s&f 15mm dia gi tubes medium grade with all fittings complete to walls and ceiling or laid in floors all as specified and directed. 41 taking up or down 20mm dia steel tubing and connections all as specified and directed. 42 fixing only 20mm dia steel tubing and connection in new or old position including all fittings, cleaning ( in wall ceiling floors etc ) all as specified and directed. 43 s&f 20mm dia gi tubes medium grade with all fittings complete to walls and ceiling or laid in floors all as specified and directed. 44 s&f in repairs 15mm dia ptmt bib taps screwed down screwed for iron pipe minimum weight 90 gram all as specified and directed. 45 s&f in repair bib taps 15mm dia cast copper alloy chromium plated fancy type long body with capstan head screwed down screwed for iron pipe or for brass ferrule all as specified and directed. 46 s&f in repairs pillar tap 15mm dia cp cast copper alloy with capstan heads fancy type screwed down high presure with or with out lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe all as specified and directed. 47 s&f in repairs stop valve 15mm dia cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union all as specified and directed. 48 s & f in repairsstop valve for 15mm bore pipe standard of ptmt any colour high pressure screwed for iron pipe complete all as specified and as directed. ( minimum weight 90gms ) . 49 s&f in repairs angel cock 15mm dia cast copper alloy chromium plated facny type with capastan head screwed both ends for iron pipe or for union all as specified and directed. 50 s&f in repair stop valve 15mm dia cast copper alloy fancy type chromium plated with long shank and cup concealed type with capastan head screwed both ends for iron pipe or for union all as specified and directed. 51 s&f in repairfor 15mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe ( minimum weight 142gms ) complete all as specified and as drected. 52 s&f in repairfor 20mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe ( minimum weight 210gms ) complete all as specified and as drected. 53 s&f pvc ( swr ) pipes 110mm dia in any length with rubber ring joint fixed to wall and including dismantling of old pipes complete all as specified and directed. 54 s&f pvc ( swr ) pipes 75mm dia single socketed in anylengthwith rubber ring joints fixed to wallor in floors andincluding dismantling of old pipes complete all as specified and directed. 55 s&f in repair pvc ( swr ) bends 110mm dia, in any radius, complete all as specified and directed. 56 s&f in repair pvc ( swr ) branch 75mm dia, in any radius, complete all as specified and directed. 57 s&f in repairs vitreous china wash down water closet ( pedestal pattern ) white complete, including connection to drain pipe and to flushing pipe and to flushing pipe antisyphonage pipe and making good floor etc complete all as specified and directed. 58 s&f in repairs squatting pan of orissa pattern long pan size 580mm white with pvc p or s trap front or back in let and foot rest including connections and making good floor complete all as specified. 59 s&f in repair plastic water closet seat white closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device all as specified and directed. 60 s&f in repairs vitreous china wash basin vitreous china white flat back 580mm x 450mm including ms brackets, excluding tap, waste pipe, chain and plug all as specified and directed. 61 s&f in repair pvc connections 15mm dia and 600mm long with ptmt nuts all as specified and directed. 62 s&f in repair 600mmx450mm beveled edge mirror of selected quality glass mounted on 6mm thick ac building board or commercial fly wood and fixed to wooden plug with chromim plated brass screw and cup washes all as specified and directed. 63 s&f in repair pvc cabinet for bathroom with looking mirror, fancy type, white or colour of size 450mm x 350mmall as directed by engr in charge. 64 s&f in repair pvc 10 lts capacity syphonic action type flushing cistern low level, white with inlet, ball valve float and handle all as specified and directed. 65 s&f in repairs brass chroumium plated shower rose 125mm size with or without swivel joints all as specified and directed. 66 s&f in repair tubular, towel rail brass chromium plated 20mm dia d type 60cm long between flanges all as specified and directed. 67 opening of air lock / blockage in gi pipe line from outlet of water tank to all internal gi pipes / fittings to smooth flow of water from bib taps / showers / whb pillar tap / stop valves complete by air pressure / water gravity pressure all as specified. 68 demolition of pcc as in ground floor & paving n exc 15cm ( below or above ) ground level including disposal of rubbish to a distance where directed. 69 material and labour 75mm thick pcc ( 1:3:6 ) type c2 ( using 40mm graded broken stone aggregate ) as in plinth protection finishing the surface even and fair including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled with mastic filling comprising 1 part of mastic bitumen and 3 parts of sand ( all by weight ) complete all as specified and as directed. 70 m&l for pcc 1:2:4 type b 1 using 20mm graded stone aggregate as in 40mm thick floor and finished even and smooth without using extra cement. 71 m&l glass dividing strips 3mm thick and 38mm wide to conform to design. 72 s&f non skid ceramic light coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in cm 1:6and dismantling of floor tiling including cement mortar bedding complete all as specified and directed. 73 m&l for light coloured ( non skid ) ceramic tiles7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm over and including 15mm thick cement screed in cm ( 1:6 ) set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tilesand dismantling of floor tiling including cement mortar bedding complete all as specified and directed. 74 m&l for ceramic glazed coloured tiles of size 300 x 200 x 6mm thick on and including 10mm thick rendering in cm ( 1:4 ) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of well and dismantling of wall tiling including cement mortar bedding complete all as specified and directed. 75 taking down cement plaster from walls including raking out joints hacking for key scrubbing down with water complete all as specified and directed. 76 m&l 15mm thick rendering on fair faces of concrete / brick surfaces of walls in cm 1:6 finished even and smooth without using extra cement complete all as specified. 77 m&l 15mm thick rendering on other than fiar faces of bricksurfaces of walls in cm 1:4 finished even fair complete all as specified. 78 m&l preparation of new plastered walls surfaces and applying two coats of oil bound distemper over one coat of primer on walls completed all as specified. 79 m&l preparation of new plastered walls surfaces and applying two coat of cement base paint completed all as specified. 80 m&l for prepartion of old surfaces and applying one coat oil bound distemper paint on walls complete all as specified. 81 demolition of brick work built in cement mortar including all quions, pillars etc. complete all as specified. 82 m&l for brick work using sub class b old size bricks straight or corved on plan exc. 6 mean radius in cm 1:6 complete all as specified and directed. 83 all as per srl item no 82 above but except bricks. 84 s&f in repair stainless steel flushing jet including pipe for europlan type closet of suitabe length with brass check nut complete all as specified & directed. 85 s&f in repairbrass cp wall mixer with provision for hand shower with wall flange and bend pipe screwed down for 15mm bore pipe complete all as specified & directed. 86 s&f in repair health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete all as specified and directed. 87 s&f in repairs brass cp central hole basin mixer without pop up waste system with braided hoses screwed down for 15mm bore pipe all as specified and directed. 88 s&f in repair pvc kit complete for low level pvc cistern all as specified and directed. 89 m&ldouble action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty . 90 s&f in brass chromium plated toilet paper holder fixed to wall with cp brass screws. 91 note: a schedule of credit for old / unserviceable demolished / dismantled items has been catered for in the tender.the schedule of credit is pre priced by mes.the final amount of the tender shall be arrived at after deducting the total amount of schedule of credit from the total amount of boq as per general summary sheet catered for after schedule of credit....

Military Engineer Services - Punjab

34773990 tender for provision of mob equipment stores for med regt ( fd regt ) and rewiring of bldg no. p 67 ( 12 qtrs ) or md accn of engr regt at 550 acre under ge ( east ) ferozepur cantt 1 b / r workexcavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, for lying cables etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft loose soil complete all as specified and as directed. 2 m&l cement concrete in foundations 1:4:8 type d 2, ( 40mm graded stone aggregate as in sub base of foundation, filling and mass concrete complete all as specified and as directed. 3 m&l for brickwork with subclass ‘b’ bricks, straight or curved on plan exc 6m mean radius built in cm ( 1:6 ) complete all as specified and as directed. 4 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm soft / loose soil complete all as specified and as directed. 5 removing excavated material / soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 6 use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter rough finishedsurface of concrete complete all as specified and as directed. 7 use and waste of formwork to sides of pillars, posts, struts, piers, columns etc rough finishedsurface of concreteall as complete all as specified and as directed. 8 use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) rough finishedsurface of concrete complete all as specified and as directed. 9 use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm widerough finishedsurface of concretecomplete all as specified and as directed. 10 use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finishedsurface of concretecomplete all as specified and as directed. 11 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed. 12 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) columns, pillars, piers, posts and struts complete all as specified and as directed. 13 m&l rcc design mix m 25 ( using 20mm graded stone aggregate ) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. 14 m&l rcc design mix m 25 ( 20mm graded stone aggregate ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. 15 m&l mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 16 all as per item no 15 above but 5mm dia and over upto and incl 10mm dia in stirupps, spacers and binders etc complete all as specified and as directed. 17 m&l rendering 12mm thickin cement mortar ( 1:4 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed. 18 m&l rendering 15mm thickin cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed. 19 m&lrendering 10 mm thick cement plaster on ceiling surfaces in cement mortar 1:4 finished fair and evenwithout using extra cement complete all as specified and as directed. 20 supply only integral water proofing compound conforming is 2645 1975 of approved make complete all as specified and as directed. 21 m&l preparation of newly plastered surfaces of walls etc, and applying three coats of white wash complete all as specified and as directed. 22 m&l preparation of new plastered surfaces of ceiling & applying two coats of white wash complete all as specified and as directed. 23 m&l applying double coats of bitumen elastometric waterproof coating as on damp proof course / roof including cleaning of surfaces complete all as specified and as directed. 24 m&l 75mm thick cement concrete 1:4:8 type c 2, using 40mm graded brick aggregate as in sub floor, sub base etc, finishing surfaces rough to receive the topping layer all as complete all as specified and as directed. 25 m & l machine pressed precast conctete interlocking paver block any shape and size confirming to is 15658 2006 of 60 mm thickness m 35 grade, jointed and pointed with gray cement and no pigment over sand cushioning complete all as specified and directed. 26 m & l sand filling under floors or in foundations including watering and consolidationcomplete all as directed by engieer in charge . 27 m&l 75mm thick cement concrete ( 1:3:6 ) type c 1 using 20mm graded stone aggregate as in plinth protection, surfaces finished even and fair without using extra cementincluding provision of construction joints complete all as specified and as directed. 28 m&l 75 mm thick cement concrete ( 1:2:4 ) type b 2 using 40mm graded stone aggregate as in floor topping, surface finished even and smooth without using extra cement complete all as specified and as directed. 29 m&l glass dividing strips, 3 mm thick and 38mm width of strip, inserted in position, conform to design complete all as specified and as directed. 30 s&f pressed steel frames ( 1.25mm sheet thickness ) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mmincluding one shop coat of red oxide primer complete all as specified and as directed. 31 s&f of 40mm thick flush door shutter of solid core construction with particle board core and plywood face panels, commercial type on both sides one face is covered with decorative face veneerwith lipping / frame to match complete all as specified and as directed. 32 s&f factory made box type steel window with pintal hinges & 2 nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing no cejz / td 06 / 07 & cejz / td 07 / 07. 33 s&f factory made box type steel window with pintal hinges & 2 nos 150 mm mild steel tower bolts to each shutter, steel handle and withoutglazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing no cejz / td 06 / 07 & cejz / td 07 / 07. 34 s&f steel ventilators fixed type complete with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and as directed. 35 mild steel framed work of e 165 ( fe 290 ) as in grills / guard bars shouldered with steel window / ventilator frames including red oxide primer coat complete all as specified and as directed. 36 s&f mild steel door handles, stove enameled black, medium wt 125 mm long and fixed with steel screws complete all as specified and as directed. 37 s&f mild steel barrel tower bolts, stove enameled black, with bright bolt, medium weight 150 mm long and fixed with steel screws complete all as specified and as directed. 38 s&f 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified and as directed. 39 s&f 3 mm thick, plainsheet glass ordinary quality and glazing, with oil putty or with wooden beads ( supplied alongwith shutters ) , in squares n.exc 0.50 sqm complete all as specified and as directed. 40 s&f stainless steel wire cloth0.56 mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staplescomplete all as specified and as directed. 41 m&l cement concrete ( 1:3:6 ) type c 1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc, complete all as specified and as directed. 42 m&l preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed. 43 m&l preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and as directed. 44 m&l preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paintcomplete all as specified and as directed. 45 e / m worksm&l for point wiring with 1.5 sqmm ( nominal area ) , pvc insulated, frls multistranded, single core unsheathed, copper conductor cables drawnthrough and including pvc conduit with allaccessories concealled in wall and fixed to ceiling etc. with and including 1.5 sqmm ( nominal area ) pvc insulated, frls unsheathed, multi stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth dolly including sunken boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for mounting switches, sockets, regulators etc complete for one light / fan / bell point controlled by one , one way switch all as specified and directed. ( a ) one light point / fan point / exhaust point controlled by one single pole one way switch. ( note: wiring shall be done in colour coding ) 46 all as per item no 45 hereinbefore butone 3 pin socket outlet 5 amps independent boardcomplete all as specified and as directed. 47 all as per item no 45 hereinbefore but one 3 pin socket outlet 5amps on the same board with other switches complete all as specified and as directed. 48 all as per item no. 45 here in before but one 15 amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 sqmm pvc insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 2.5 sqmm green colours pvc insulated, unsheathed, stranded copper conductor cable. 49 all as per item no. 45 here in before but one 15 amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 sqmm pvc insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 4.0 sqmm green colours pvc insulated, unsheathed, stranded copper conductor cable. 50 s&f switch piano flush type 6 amps, single pole one way, white in colour, duly isi marked complete all as specified and directed. 51 s&f switch piano flush type 20 amps, single pole one way, white in colour, duly isi marked complete all as specified and directed. 52 s&f socket outlet2 in 1, 5 pin, 6 amps, white in colour, duly isi marked complete all as specified and directed. 53 s&f socket outlet, uni, 2 in one10 amps & 20 amps, white in colour, duly isi markedcomplete all as specified and directed. 54 s&f ceiling rose surface type, 240 volts, 50 hz, 6a, pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals dulyisi marked complete all as specified and directed. 55 s&f rotary stepped type electronic fan regulator for ceiling fan 1200 / 1400mm size, 240 volts, 6 amps, 100w, white in colour, duly isi marked complete all as specified. 56 s&f lamp angle holder ( plastic ring ) , 240 volts, 50 hz, 6a, white in colour, duly isi marked complete all as specified and directed. 57 s&f led bulb of 9 watt, b22, 6500k all as specified and directed. 58 s&f 20w, 6500 k, 4 feet led square tube light fitting, energy efficient fixed to wall / ceiling etc complete all as specified and as directed. 59 s&f led sleeky bldg street light ( lens ) fitting of 35 watts, 6000k, including gi bracket bend to shape made out of gi pipe light grade of 25 mm, size up to 1.2 mtr long etc complete with ms clamps made of 25x3mm ms plate, duly painted with two coats of aluminium paint with nuts / bolts / washers and all fixing arrangements to wall / pole, including connecting up with 2 core copper flexible wire of size 23 / 00.0076 complete all as specified and as directed. 60 s&f exhaust fan heavy duty with louvers complete of sweep size 300mm, 900 rpm, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of pvc flexible copper cable of size 23 / 00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and as directed. 61 s&f ceiling fan 1200mm sweep, ac single phase 230 volts 50hz, at bldgs upto 5 mtrs height, including provision of flexible cable 3 core copper conductor of size 23 / 0.0076 of suitable length from ceiling rose to ceiling fan upto 1.5 mtr for giving connection and all hanging arrangement i.e. standard down rod, hanging clamp, with rubber real nuts bolts, spring washers and locking of splite pin, plastic canopy with screw compete without fan regulator and marking of mes nos with black synthetic enameled paint all as specified and as directed. 62 s&f factory made sheet metal enclosures double door type made out of crca 1.2 mm thick m.s. sheet, powder coated, partly embedded in wall, ip 43 protection, vtpn db with 200 amps rated bus bar, 4 way, 415 volts, vertical type, dust and vermin proof, suitable for incorporation of mccbs / mcbs, factory made, including thermal based release adjustable type 4 pole 63 amps, 50 hz, 415 volts with rupturing capacity 16 ka and making good distrubbed surfaces with matching colour, complete all as specified and as directed. 63 s&f factory made sheet metal enclosures double door type made out of crca1.2 mm thick m.s sheet, powder coated, spn db with 200 amps rated bus bar, 8 way, ip 42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of mcbs duly cocealled in wall, factory made, including making good distrubbed surfaces with matching colour complete all as specified and as directed. 64 s&f mcb spn, 40 amps, 240 volts, b series, 10ka duly isi marked, complete all as specified and as directed. 65 s&f mcb sp, 6a 32 amps, 240 volts, b series, 10ka duly isi marked, complete all as specified and as directed. 66 m&l for sub main wiring with two single core 2x4 sqmm pvc insulated and unsheathed stranded copper conductoralongwith earth wire 4.0 sqmm drawn in including pvc rigid conduit connected to main board complete all as specified and directed ( note: two runs cable and one number earth wire and suitablepvc conduit shall measured together as unit length ) . 67 m&l for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanised iron or steel wire complete all as specified and as directed. 68 m&l for earthing complete with galvanized steel plate elecrode of size60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead gi wire of 4mm dia ( 8 swg ) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. the other end of gi earth wire is connected to main switch board and protected by light grade gi pipe of 15 mm bore. provision of 20mm bore light grade gi pipe for watering including gi funnel and wire mesh. pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. cement concrete chamber of pcc ( 1:3:6 ) type c 2 using 40 mm graded stone aggregate.the chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate and ms angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in electrical plate no 3 of ssr part 1 ( 2009 ) . 69 supplying, laying, jointing and testing xlpe insulated, armoured, electric cables ( heavy duty ) with aluminium conductor, 1100 volts, grade cross sectional area 25 sqmm 4 core confirming to is:7098 1985 laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and as directed. ( note: excavation & earth work, cable preotection coverand sand cushion shall be measured &separately ) 70 m&l dry and clean fine sand for cable cushioningto underground cable protection, complete all as specified and as directed. note punned down thickness shall be measured. 71 s&f cover to underground cable with one layer of bricks using sub class ‘b’ bricks ( old size ) laid flat across the cable complete all as specified and as directed. 72 s&f mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles / walls, laid under floor / road crossings, complete with and includingclamps socket & elbow etc complete all as specified and as directed. 73 taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5 / 15 amp points complete withfitting and fixtures such as switches, sockets, c / rosess, holders and bracket fittings with battens / conduits / wires, t / l fittings and making good the disturbed surfacesof walls and roofs etc.and to match with existing colour complete all as specified and directed. 74 taking down carefully unserviceable main switches and distribution boards with fuses / mcbs ( single phase or three phase ) of any capacity complete all as specified and as directed. 75 taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified 76 s&f bell push flush, type 6 amp single pole one way, white in colour, duly isi marked complete all as specified and as directed. 77 s&f door bell ding dong single phase 240 volts, white in colour, duly isi marked complete all as specified and as directed. 78 s&f batten holder ( with metal ring ) , 240 volts, 50 hz, 6a, white in colour, duly isi marked complete all as specified and as directed. 79 s&f factory made three phase and neutral sheet steel made out of crca 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing mcbs and the second for protection of mcbs fitted with colour bus bar of capacity 200 amps, neutral link, earth bar and din rail suitable for use on 240 / 415v, 50hz supply, vtpn db, partly immersed in wall, including of mccb 4 pole adjustable thermal & fixed magnetic type 100 amps, 50hz, 415 volts with rupturing capacity 16 ka and making good distrubbed surfaces with matching colour, complete all as specified and as directed. 80 s&f mcb spn, 40a 63amps, 240 volts, c series, 10ka duly isi marked, in mcb db, complete with connection testing and commissioning complete all as specified and as directed. 81 m&l for sub main wiring with two single core 2x6 sqmm frls insulated and unsheathed stranded copper conductoralongwith earth wire 6.0 sqmm frls drawn in includingrigid conduit connected to main board complete all as specified and directed ( note: two runs cable and one number earth wire and suitableconduit shall measured together as unit length ) . 82 cutting holes making good the distributed surface, grouting nuts for fixing of exhaust fans complete all as specified and directed. 83 m&l for disconnecting electric meter of any cap and refixing same after rewiring, in meter box including connection complete all as specified and as directed. 84 s&f sheet metal meter box single door minimum size 35x50x25cm for electric meter factory made of ms sheets / crca sheet duly painted with powder paint and door hinged locking arrangement conforming to is 5039 of 1983. the electric meter / switch box shall be suitable for fixing one number of electric meter and knock out holes for incoming and outgoing cable. before the powder paint process the sheet steel shall go through the anti corrosion conditioning process in not less than seven tank process. concealed in wall, including making good distrurbed surfaces with matching colour, complete all as specified and as directed. 85 fixing or hanging only ceiling fans height upto 3mtr to 5 mtrs ceiling height of bldg including three core fr pvc insulated & overall round sheathed flexible with pvc, colour of cores are red, black & yellow / green is for earthing. sheath colour is black of cable size 23 / 0.0076 complete all as specified. ( note : ceiling fans obtained / taking down from item sr no.73 as above ) ...

Military Engineer Services - Punjab

34417623 annual maintenance of jcos or md accn in candeth & malhotra enclaveunder age br i of ge n mamun 1 taking down chowkhats of frames n.exc 1.50 sqm with shutters ( without taking off shutters from the frames ) , removal from site complete all as specified and directed. 2 all as per srl item no 1, but exceeding 1.5 sqm and n.exc 4 sqm. 3 taking down shutters of any description exc 1 sqm but n exc 2 sqm each, removal from site complete all as specified and directed. 4 taking down shutter exc 1 sqm to 2 sqm and refixing in same opening safely, ( including minor repair ) complete all as specified and directed. 5 s&f box type steel windows and ventilators comprised of tubular frame and shutters made out of 1.25 mm thick m s sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter ( wire cloth and glass panes only shall be measured and paid seperately ) with side hung shutters with steel handle and steel peg stay dovetailed or welded including 2 nos tower bolts 150 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to fi frame work, including other fittings, hinges, handles, tarred hold fasts, pcc blocks etc all as shown on drg no cepz / td 354 / 09 sheet 1 / 3 to 3 / 3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 6 s&f pressed steel frame made out of ms sheet 1.25mm thick of size 125x60mm for doors / windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type c 0 ( 12.50 mm graded aggregate ) back of chowkhats and including two coats of synthentic enamel paint over shop coat of primer complete all as specified and sirected. 7 all as per item 6 but size 105x60 mm. 8 s&f 2nd class hard wood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass or gauge etc ( divided into squares with plain chamfered or rounded , mitred and rebated sash bars, any numbers ) , edges of framing plain chamfered or rounded fitted with cut and mitered beads and fitted to chowkats for securing glass / gauge size of stiles rails and other parts as per clause 8.24 ( a ) of ssr part icomplete all as specified & directed. 9 s&f 35mm thick factory made plain framed panelled shutters of 2nd class hard wood two panel with lock rail and panel of 9mm thick bwp commercial ply. the size of rail and stile as per is 1003 ( part i ) kiln seasoned and chemically pressure treated factory made shutters wood is to be incorporated complete all as specified and directed. 10 m&l preparation of wood or wood based surfaces of any descriptionover 10 cm width or girth and applying two coats of synthetic enamelpaint over a coat of pink primer complete all as specified and directed. 11 m&l for 18 to 20 mm thick perlaminated pvc solid board with acrylic lamination not less than 0.50 mm thick ( one side decorative choice laminaate and other side balancing white ) having weight not less than 9 kg / sqm as in kitchen cabinet, cupboard with suitable 125 mm long fancy handle ( as per sample ) and pelmet box fixed with screws to pvc / timber frame work complete all as specified and directed. 12 s&f factory made wood grain solidpannel pvc door shutter 30mm thick ( style ) consisting of frame made out of ms tube s for top and bottom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour & as gap insert for top rail & bottom rail panelling of plain colour sheet to be fitted in ms frame welded / sealedto stiles & rails with suitable pvc sheet beadingand joined together with solvent cement , supplying & fixing in the frame at site as per specification & drawing compete all as specified and directed. 13 m&l soild pvc door frame wood grain colour coated of size 50mm x 95mm made out of 5mm wood grain colour pvc sheet reinforced with ms sqaure tube , supply and fixing in opening as per specification & drawing complete all as specified and directed. 14 m&l for repair to old steel window shutter not exc 1 sqm each including replacement of all hinges, handle, and necessary welding to shutter and chowkhat for making window in serviceable condition including two coats of synthetic enamel paint complete all as specified and directed. 15 all as per item 14 butexc 1 sqm and n exc 2.00 sqm each. 16 s&f for 100 mm long butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and as directed. 17 s&f for 100 mm long hasp staples, mild steel wirw type stove enamelled black including bolt to hinge plate and fixed with screws complete all as specified and as directed. 18 s&f aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded setion or cast aluminium alloy and fixed 250 mm long complete all as specified and directed. 19 s&f anodised aluminium barral tower bolt extruded section 200 mm size complete all as specified and directed. 20 s&f anodised aluminium handle cast type 125 mm size complete all as specified anddirected. 21 hacking out old broken glass ( any thickness , size, quality, or description ) from wooden frame glazed with putty or fixed with beads, rubbish off the premises complete all as specified anddirected. 22 s&f frosted glass pin head type 3 mm thick ordinary quality and glazing with oil putty n.exc 0.5 sqm in each pane complete all as specified and directed. 23 all as per item no. 22 but plain 3mm thick sheet glass. 24 s&f mild steel 300mm, ordinary rat tail rod pattern springs including roller & roller plate including necessary welding complete all as specified and directed. 25 s&f in repairms helical aluminium door spring 150mm size fixed to steel framecomplete all as specified and directed. 26 s&f for stainless steel wire cloth 0.36 mmnominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, or galvanized wire staples complete all as specified and directed. 27 all as per item no. 26 but s&f in repair. 28 taking up or down steel water tubing and connections including cleaning for refixing or removal to store for bore of pipe 15mm borecomplete all as specified and directed. 29 s&f 15mm bore tubes medium grade galvanized isi marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc, complete all as specified and directed. 30 all as per srl item no 29, but fixing only 31 all as per item no 28 but 20mm bore. 32 all as per item no 29 but 20mm bore. 33 all as per srl item no 32, but fixing only 34 taking down eaves gutters and rainwater pipes 100 mm dia ( any size or pattern ) , including all fitting , head , shoes , bend, swan nacks etc., including cleaning or refixing or removal to store complete all as directed and directed. 35 s&f pvcb ( swr ) pipes 110mm bore, single socketd , in any length with rubber ring joints , in any length fixed to walls, complete all as specified and directed. 36 s&f pvc ( swr ) bend any radius 110mm dia borecomplete all as directed. 37 m&l cutting chases pinning in brick mas and making good to facing where required and pointing in cement and making good in cm 1:3 cutting n.exc. 10cm in girth complete all as specified and as directed. 38 m&l for ( 60 to 100 mm thick ) repair to rcc sunshades, chajjas, balconies, columns, bands, beams and similar rcc work at any position / height by dismantling loose / disintegrated portion, dubbing out with cement concrete 1:1½:3, using 6 to 12.50mm graded stone aggregate required shape and finish including provision of necessary formwork / supports etc ( upto double storey bldg ) , removing correded reinforcement , with and including providing ( duly welded ) new reinforcement as per existing or ( as directed ) required as per site condtion, rendering exposed surface with plaster 5mm thick in cm 1:3 mixed with wpc as per manufacturer instruction, applying two coats of exterior emulsion paint over a coat of primer complete all as specified and as directed. 39 m&l glazed ceramic coloured tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including bedding layeer of mortar 10mm thick in cm ( 1:4 ) , finished rough including dismantlingfloor, hearth or wall tiling including cement mortar bedding ( but not backing removing serviceable tiles to store and rubbish off the premises complete allas specified & directed. 40 all s per item 39 but non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqmbut not exceeding 0.18 sqmin floors, laid over 15mm thick screed bed cm 1:6. 41 m&l marble work 14 to 16mm thick ( table rubbed and polished ) in cooking plateformwindow cill etc in cement mortar including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match set and jointed in neat cement slurry and pointed in coloured cement ( to match ) laid over 15mm thick screed bed in cm ( 1:6 ) including dismantling of existing marble work, bedding layer of mortar, rubbish off the premises all as specified and as directed. 42 all as per item no 41 but in vertical surface ( skirting / dado etc ) laid over bedding layer of mortar 10mm thick in cm ( 1:4 ) . 43 s&f in repair angular stop cock15mm bore dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 44 s&f in repairbib taps for 15 mm bore dia, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrulecomplete all as specified and directed. 45 all as per item 72 but long body 46 s&f in repair pillar tap 15 mm bore dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lette ed hot or cold with long screwed shanks and fly nuts, screwed for ironpipe and fixed complete all as specified and directed. 47 s&fin repairs vitreous china wash basin, white flat back, size 550 x 400 mm including waste pipe , brackets and cutting for and pinning in ends of brackets or errecting standwith waste coupling and 32 mm diawaste pipe complete all as specified and directed. 48 s&f in reapirtowel rail cp 24, dia 3 / 4 size complete all as specified and directed. 49 s&f in repair cp soap dish holder complete all as specified and directed. 50 s&f in repair 600 x 450 mm bevelled edge mirror of selected quality glass 5mm thick, mounted on 6 mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified. 51 s&f ci floor trap 75mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type b 1 with cp grating with or without hole for waste pipe complete all as specified and directed. 52 s&f in repair pvc flushing cistern 10 ltr capacity including pvc connection inlet and and outletconnections, brackets, pvc flush pipe with bend 32 mm dia of suitable length including making necessary connections to water supply pipe line and jointing to wc complete all as specified and directed. 53 s&f vitreous china wash down water closet pan pedestal pattern, white ( excluding supply of flushing cistern and flush pipes, but including fixing thereof ) , including making connections to trap, and to flush pipe including plastec seat and cover ( as directed ) with stainless steel or aluminised hinging device and fixed in repair complete all as specified and directed. 54 s&f in repair 32mm dia pvc waste pipe complete all as specified and directed. 55 s&f in repair 20mm dia of pipe bass brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. 56 s&f in repair health foucet hand shower 8mm dia 1m long flexible hook and wall hook complete all as specified and directed. 57 s&f in repair vitreous china, squatting from pan orissa pattern white size 580mm x 440mm white with integral footrest including provisionof lean concrete bedding connection to drain out pipe and to flush pipe and to flush pipe anti syphonage pipe etc complete including making good to floor where required competeall as specified and directed. 58 s&f cover for plastic water closet seat, closed pattern with flat bottom & cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. 59 s&f pvc connections 15mm size with ptmt nuts of length 450mm complete all as specified and directed. 60 s&f in repair20mm dia mild steel fancy type dropery rod, wooden shade withpvc bracket and pvc fenial fixed over doors and windows with steel screws and pvc rawl plug / cleat complete all as specified and directed. 61 s&f sink with drainage board made of stainless steel 1 mm thick kitchen laboratory with plugs, washer and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx415mmx460mm bowl size 410 mm x330mmx160mm complete all as specified and directed. 62 s&f rotational moulded polyethlene water storage tanks of capacity 500 litres two layers ( cylindrical vertical with closed top ) , isi marked hoisted and fixed in position all as specified in ssr part i complete including 20mm dia ball brass valve high pressure with polythene float and dismantling of existingtank ( rcc or pvc ) of any capacity complete all as specified & directed. 63 s&f in repair 20mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixedcast copper chromium plated fancy type alloy isi marked with crutch or butter fly handles screwed down screwed for iron pipe of 20mm bore complete all as specified and directed 64 s&f in repair pvc lidfor water tank of capacity 500 ltrcomplete all as specified and directed. 65 dismantling brick tile or terracing tiles single layer on s / s or d / s roof complete all as specified and directed. 66 m&l pcc 1:2:4 type b 0 ( using 12.5 mm graded stone aggregate ) padding as levelling course / padding using water proofing compound laid over existing roof , suface finished rough to recieve cement mortar including necessary formwork including demolition of existing concrete of any description and removal of debris out of the premises complete all as specified and as directed.note ; ( wpc shall be measured and paid seperately ) . 67 m&l forcement concrete ( 1:2:4 ) type b1 ( using 20 mm graded crushed stone aggregate ) as in repair to chajjas, roof projection, kerbs ( gola to joint with parapet etc ) and the like rounded or chamfered on edges including necessary form work complete all as specified and as directed. 68 m&l 20mm thick cement plaster in cement mortar 1:4 on concrete surface, surface finished even and smooth using wpc ( liquid ) as per manufacturer instruction or @ 0.200 ltr in 50 kg of cement complete all as specified and as directed 69 m&l for app modified roof treatment over existing non accessible rcc roof slab / chajjah / canopy / parapet wall ( to be executed through approved applicator of the membrane manufacturer ) with following specification etc complete all as specified and directed : ( a ) cleaning existing surface properly, applying oil bound bitumen primer @ 0.30 liter / sqm manufacture by the same agency as that of app with a density 0.87 0.89 kg per liter at 25 degree centigrade on prepared surface, laying not less than 3.0mm thick app modified water proofing membrane, weighing not less than 3.60 kg / sqm, reinforced with non woven polyster fiber weight not less than 160gsm / sqm using butane torch by torch application with 10cm side laps and 15cm end lap. ( b ) top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 kg / sqm as prescribed by manufacture of membrane. 70 taking down cement plaster on brick walls or stone walls any descrition etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed. 71 m&l for 15mm thick cement plaster in cm 1:4 ( in two layers i.e 1st layer 10mm, external layer 5mm thick ) on stone masonary or other than fair faces of brick work surfaces finishing the surfaces even and smooth without using extra cement. external layer of plaster shall be using wpc complete all as specified and directed. ( note: wpc shall be measured and paid seperately ) 72 m&l rendering 10mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar ( 1:6 ) finished even and fair without using extra cement all as specified and directed. 73 m&l rendering 5mm thick cement plaster on faces of concrete surfaces in cement mortar ( 1:3 ) as in ceiling finished even and fair without using extra cement all as specified and directed. 74 m&l preparation of new plastered surface of walls and applying wall care putty ( any thickness ) to obtain the surface even and smooth, applying two coats of oil emulsiondistemper complete all as specified & directed. 75 m&l preparation of new plastered surface of external wall surface applying two coat of cement base paint including curing complete over a coat ofalkali resistant priming paint complete all as specified & directed. 76 m&l three coats of white wash on newly plastered surface of walls including preparation of surfaces complete all as specified and directed. 77 m&l two coats of white wash on newly plastered surface of ceiling including preparation of surfaces complete all as specified and directed. 78 m&l for complete removal of existing treatment from walls, applying wall care putty ( any thickness ) to obtain the surface even and smooth, and applying two coats of distemper oil emulsion, white or tinted complete all as specified & directed. 79 m&l forpreparation of old plastered surfacesby scrapping down smoke roots, moulds salts and treading oil and greasy spotswith wire brush and applying one coat of white wash on wall complete all as specified & directed. 80 m&l forpreparation of old plastered surfacesby scrapping down smoke roots, moulds salts and treading oil and greasy spotswith wire brush and applying one coat of white wash on ceiling complete all as specified & directed. 81 m&l forpreparation of old plastered surfacesby scrapping down smoke roots, moulds salts and treading oil and greasy spotswith wire brush including removing all nails & washing with clean water down and applying one coat of oil bound distemper on wall , white or tinted complete all as specified & directed. 82 m&l prepration of old steel surfaces of anydescription, not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint , white or tinted complete all as specified and directed. 83 m&l prepration of old wooden surfaces of anydescription, not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint , white or tinted complete all as specified and directed. 84 dismantling of brick work built in cement mortar including all quoins, arches, pillars etc, rubbish off the premises complete all as specified and directed. 85 m&l for brick work with fly ash bricks ( old size bricks ) straight or curved on plan exc 6 mtr mean radius built in cm ( 1:6 ) complete all as spd and directed 86 all as per item 85 but using old servicable bricks. 87 demolition of cement concrete ( un reinforced ) in ground floor and paving n.exc 15 cm thick ( below or above ground level ) , removal of rubbish complete all as specified and directed. 88 m&l 75mm thick cement concrete type c 1, 1:3:6 ( using 20mm graded stone aggregate ) as in plinth protection, laid in slope finished even and fair including making joints at every 2.5 m and at corner, filled with bitumen 85 / 25 and sand in ratio 1:2 by weight complete all as specified and directed. 89 s&f in repair 100 mm bore ci bends ( any radius ) diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed. 90 all as per item 89 but 75 mm bore ci bends 91 all as per item 89 but with ovel asses door 92 all as per item 90 but with ovel asses door 93 s&f in repair cast iron branch peices, single ( equal or unequal ) ordinary or inverted ( spigot or socket type ) , or with parrallel branches fitted with oval access doors of 100 mm bore diacomplete , isi marked complete all as specified & directed. 94 all as per item 93 but 75 mm bore. 95 s&f 100 mm bore cast iron ( sand cast ) soil waste and vent pipes isi marked in any length with or without ears fixed to walls with clamps and cement joints including dismantling complete all as specified and directed. 96 all as per item 95 but 75 mm bore. 97 all as per item 95 but 75 mm bore, laid in floor with cement joints. 98 all as per item 95 but 50 mm bore. 99 all as per item 95 but 100 mm bore, laid in floor with cement joints. 100 s&f in repair cast iron cowl for 50 mm dia complete all as specified and directed. 101 m&l for opening of air lock in gi pipe 15mm / 20mm by removing / taking down of gi pipe ( including flushing out sand / silt ) and refixing as same to obtain optimum water pressure complete all as specified and directed. 102 m&l for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litre per linear meter including drilling and plugging of holes etc in apron / plinth protection complete all as specified in is code 6313 part ( 3 ) : 2001 and as directed by engr in charge. note: chlorphyriphos 20% ec or lindane 20% ec isi marked shall be used. 103 m&l for providing and injecting chemical emulsion for post constructional anti termite treatment of soil under existing floors using chemical emulsion @ one litre per hole 300 mm apart along the junction of floor and wall, along joints in floors including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floor complete all as specified in is code 6313 part ( 3 ) : 2001 and as directed by engr in charge.note: chlorphyriphos 20% ec or lindane 20% ec isi marked shall be used. 104 m&l 10 mm thick cement plaster in cm 1:3 on brick or concrete surface of sunken floor finished even and smooth using wpc liquid @ 0.200 ltr in 50 kg of cementor as per manufacturers instructions complete all as specified & directed. 105 m&l forbitumen blown any grade, applied hot, two coats to concrete / plastered surfaces @ 1.5 kg per sqm per coat and applying polythene film black, 50 micron complete for sunken floor slab duly embedded in side wall / covered fillet complete all as specified and directed. 106 supply only liquid water proofing compound. 107 m&l for 25 mm thick pcc type b 1, 1:2:4 ( using 20mm graded crushed stone aggregate ) as in sub floors for laying floor finish complete all as specified and directed. 108 m&l plain cement concrete 1:5:10 type e2 using 40mm graded stone aggregate as in sunken floors and complete all as specified and directed. 109 m&l for kitchen slab / shelves supported on wall / beams using reinforced cement concrete type b1 ( 1:2:4 ) using 20 mm aggregate ( max thickness of slab 100mm ) including necessary formwork and demolition of existing slab / shelves, removal of rubbish complete all as specified and as directed. 110 m&l tmt steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips compete all as specified and as directed. 111 deduct:total amount of schedul a section ii ( sch of credit ) rs 59325.00 ( to be deducted from schedule ‘a’ ( boq ) to arrive at the contract sum....

Northern Railway - Punjab

34121403 provision of additional fitting arrangement for cantilever assemblies at curve locations in tunnel between jammu tawi ( jat ) katra ( svdk ) section over firozpur division...

Central Public Works Department - Punjab

33972464 annual repair maintenance of to residential and technical buildings at no.1fbsu airforce rajasansi amritsar during 2022 23 sh: repair of cantilever chajjas at various location....

Military Engineer Services - Punjab

33626782 comprehensive maintenance and repair to b / r items in d 1a zone area under age b / r ii of ge ( south ) mamun 1 m&l pcc 1:2:4, type b 2 ( using 40mm graded crushed stone aggregates ) as in foundation, flooring, mass concrete including dismantling of existing flooring etc complete all as specified and directed. 2 m&l pcc 1:2:4, type b 1 ( using 20mm graded crushed stone aggregates ) as surface channels and drains complete all as specified and directed. 3 m&l for precast cement concrete 1:2:4, type b 1 ( using 20mm graded crushed stone aggregate ) as in kerbs mud stops, rounded or chamfered on edges complete all as specified and directed. 4 m&l for pcc 1:2:4, type b 1 ( using 20mm graded crushed stone aggregates ) as in base / anchoragefor fixing to trusses and the like, complete all as specified and directed. 5 m&l for precast cement concrete 1:2:4, type b 1 ( using 20mm graded crushed stone aggregates ) as in landings, cover slabs ( for man holes etc. ) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cm 1:6, complete all as specified and directed. 6 m&l for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi tred / stopped ends etc complete all as specified and directed. 7 m&l for brick work with fly ash bricks, straight or curved on plan exc 6 mtr mean radius, built in cm 1:6, complete all as specified and directed. 8 m&l for form work to flat, rough finished surfaces of concrete of chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. 9 s&f 35mm thick 2nd class hardwood factory made plain framed, panelled shutter ( two panel ) with lock rail and panel of 9mm thick bwp commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 ( part i ) , kiln seasoned andchemically pressure treated, complete all as specified and directed. 10 s&f 35mm thick factory made wire guazed and skeleton shutters ( 1st class softwood ) , open rebated and prepared to receive wire cloth, gauze etc. ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing wire cloth etc. sizes of members of shutters as specified in ssr part i, section 8, clause 8.24 ( a ) and fitted to chowkats at site, complete all as specified and directed. 11 s&f factory made solid panel pvc door shutter 30mm thick ( style ) consisting of frame made out of ms tubes for top & bottom rails, ms frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rails with suitable pvc sheet beading and joined together with solvent cement, suppling & fixing in the frame at site, complete all as per specifications & drawing. 12 s&f solid pvc door frame of size 50mm x 47mm, made out of 5mm thick plain colour pvc sheet reinforced with ms square tube, suppling & fixing in opening at site, complete all as per specifications & drawing. 13 s&f as in repair factory made 18mm ( +0.7mm ) thick pvc sheet one side prelam for cupboard shutter of density 600 kg / cbm bent 90 degree and finish at all edges at level for making edge lipping / bending or 0.5mm thick pvc sheet lipping at 4 edges using bonding tape complete all as per manufacturers specifications 14 s&f 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. 15 s&f 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. 16 s&f as in repair 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. 17 s&f as in repair 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. 18 s&f 250mm long aluminium alloy, anodised sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed. 19 s&f 100mm long butt hinges, type c 21, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed. 20 s&f 150mm long aluminium handle, cast type, anodised complete all as specified and directed. 21 s&fas in repair 300mm size mild steel, ordinary rat tail, rod pattern spring including roller and roller plate, complete all as specified and directed. 22 s&fas in repair20mm bore mild steel drapery rod with 1.0mm thick pvc wood grain coating including brackets and knobs, fixed on windows and doors for hanging curtains, complete all as specified and directed. 23 s&f stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. 24 s&f as in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. 25 s&f as in repair anodised aluminium window and ventilator shutters, side hung or sliding type without sash bar, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long ( 1 no. ) , hinges 100mm long ( 2 nos ) and suitable handles as required, complete all as specified and directed. 26 s&f as in repair anodised aluminium door shutter, aluminium section weighing not less than 0.55 kg / m including necessary jointing cleats, glazing clips, rubber neoprene packing, 2 nos handle150mm long and two nos 150mm long aluminium tower bolts in each shutter, hinges, anonised aluminium snap beading, fixed with screws, complete all as specified and directed. 27 s&fas in repair anodised aluminium frame work for doors, window, ventilators, partition walls with one or more rebates including joining cleats for fixing etc, complete all as specified and directed. 28 s&f box type steel windows and ventilators, comprised oftubular frame and shutters made out of 1.25mm thick ms sheet tube, factory made with double side hung wire gauged shutter & glass / glazed shutter ( wire cloth and glass panes shall be measured and paid separately under respective items of boq ) with steel handle and steel peg stay dovetailed or welded including 2 nos. tower bolts of 150mm long for each leaf and 10mm square bar grills at spacing as shown on drawing, welded to fi frame work including other fittings such as hinges, handles, tarred hold fasts etc. fixed in pcc blocks including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as shown on drawing no. cepz / td 354 / 09 sheet 1 / 3 to 3 / 3. 29 s&f pressed steel frame made out of ms sheet 1.25mm thick of size 125mm x 60mm for doors / windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including filling of concrete 1:3:6 type c 0 ( 12.5mm graded stone aggregate ) as in back of chowkhats and including two coats of synthentic enamel paint over a coat of red oxide primer, complete all as specified and directed. 30 s&f pressed steel frame made out of ms sheet 1.25mm thick of size 105mm x 60mm for doors / windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including filling of concrete 1:3:6 type c 0 ( 12.5mm graded stone aggregate ) as in back of chowkhats and including two coats of synthentic enamel paint over a coat of red oxide primer, complete all as specified and directed. 31 m&l for mild steel tmt bars 10 mm dia and over, cut to length, bent to shaperequired including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9 mm diacomplete all as specified and directed. 32 s&f tubular framed steel trusses ( all as per pattern of existing dismantled trusses ) made out of ms medium grade tube ( erw or induction butt welded ) upto 60mm bore conforming to i. s.1161 1979 grade st. 240 quality a, including welding of distance pieces, cleats, special shaped washer etc. and applying two coat of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed. 33 s&f steel screw bolts ( machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and n. exc. 30cm long, 16mm dia of shank, complete all as specified and directed. 34 m&l pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick ( isi marked ) of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. 35 m&l pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick ( isi marked ) of any colour having tensile strength of 550 mpa as in ridge / valley , gutter or straight flashings etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. 36 m&l false ceiling of 9.5mm thick gypsum tiles ( 600x600mm ) laminated with pvc film on the face side & metalised polyester film on the back side with all four edges sealed with pvc film ( shade either plain white or colour ) fixed using t grid / cross t / wall angle / level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type / pattern complete all as specified and directed. 37 m&l for removing existing roof treatment ( any type ) and roughening surfaces of old concrete floor by picking, sweeping / brushing clean and washing down with water to remove dust etc, and applying neat cement slurry with 3kg of cement per sqm complete all as specified and directed. 38 m&l for 20mm thick cement plaster on roof top in cement mortar 1:4 on concrete surfaces, finished even and smooth without using extra cement including and mixing with wpc @ 0.200ltr / 50 kg bag of cement, complete all as specified and directed. 39 m&l for app modified roof treatment over existing non accessible rcc roof slab / chajjas / canopy / parapet wall, to be executed through approved applicator of the membrane manufacturered as per following specifications, complete all as specified and directed : ( a ) cleaning the top surface of rcc roofing properly with water. ( b ) applying oil bound bitumen primer @ 0.30 litre / sqm, manufactured by the same agency as that of app with a density 0.87 0.89 kg / litre at 25 degree centigrade on prepared surface. ( c ) laying of membrane not less than 3.0mm thick app modified water proofing membrane weighing not less than 3.60 kg / sqm reinforced with non woven polyster fiber weight not less than 160 gms / sqm using butane torch by torch application with 10cm overlap and 15cm end lap. ( d ) top of membrane shall be provided with solar reflective bituminous aluminum paint @ 0.10 kg / sqm as prescribed by manufacturer of membrane. ( e ) app membrane shall be stick inside parapet where available by chase cutting and sealed with pcc 1:2:4, type b 0. 40 m&l for 40mm thick fly ash brick tiles laid on 15mm thick cement plaster on roof top in cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement over app membrane including dismantling of existing brick tiles, complete all as specified and directed. 41 m&l for 75 mm thick plain cement concrete 1:4:8 type d 2 ( using 40 mm graded crushed stone aggregate ) as in sub base of floors, including demolition of existing floor complete all as specified and directed. 42 m&l for 40mmpcc 1:2:4 type b 1 ( using 20 mm graded aggregate ) as in floors laid in panels n. exc. 2.5 sqm with top finished the surface even and smooth without using extra cement including glass dividing strips as per site requirement complete all as specified and directed 43 m&l for 75mm thick cement concrete 1:3:6, type c 1 ( using 20mm graded crushed stone aggregate ) as in plinth protection and paving, laid in slope, finished even and fair including making joints at every 2.5 mtr and at corner filled with bitumen 85 / 25 and sand in ratio 1:2 by weight, complete all as specified and directed. 44 m&l for coloured machine pressed precast rubber moulded concrete interlocking ( grey / red / yellow ) paver block of any shape and size with 6 8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to is 15658 2006 of 60mm thickness, m 35 grade, laid dry over and including 50 mm thick screened river washed sand cushion, and dismantling existing interlocking paver block of any shape and size removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 45 m&l interlocking paver block of any shape of 60mm thickness, m 35 grade, ( except blocks ) laid dry over and including 50 mm thick screened river washed sand cushion, complete all as specified and directed. 46 m&l for fly ash glossy finished coloured chequered cement concrete tiles of size 30cm x 30cm x 25mm thick, set, jointed & pointed in neat cement slurry with grey cement and pigment to match as in floors over and including 15mm thick screed bed or bedding layers in cm 1:6, including dismantling existing floor, hearth or wall tiling of any description, complete all as specified and directed. 47 m&l for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc, set and jointed ( joint free ) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in cm 1:4 for layingfloor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 48 m&l for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors etc, set and jointed ( joint free ) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in cm 1:4 for layingfloor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 49 m&l for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in cm 1:4 and finished rough to receive tiles including dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 50 m&l for 10mm thick vitrified ceramic light shade colour tile ( square or rectangular ) , polished, area of each tile not exc 0.36 sqm ( joint free ) as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in cm 1:6 and finished rough, including dismantling floor, hearth or wall tiling complete all as specified and directed. 51 m&l for marble work ( green / black marble bhaislana zebra ) 18 20mm thick ( table rubbed and polished ) as in cooking plateform, window cills, jambs, steps and like over and including 15mm thick screed in cm 1:4 including pointing with white cement ( 1:2 ) using marble dust with admixture of pigment to match the marble shade including rounding the exposed edges full round, and making hole for gas pipe, including demolition of existing stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed. 52 m&l for machine cut kota stone slab flooring / treads of steps 18 20mm thick over and including 20mm thick screed bed in cm 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in floors / cills etc, and moulding at edges if required complete all as specified and directed. 53 m&l for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 54 m&l for 15mm thick rendering in two layers ( 5mm thick in cm 1:4 over 10mm thick in cm 1:6 ) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including wpc @ 200ml / bag of cement, including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 55 m&l for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying two coats of white wash, complete all as specified and directed. 56 m&l for preparation of old surfaces of ceiling including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying two coats of white wash, complete all as specified and directed. 57 m&l for preparation of old surfaces of walls of any description after complete removal of existing treatment and applying 2mm thick wall care putty for making the surfaces smooth and applying two coats of oil emulsion distemper, complete all as specified and directed. 58 m&l for preparation of newly plastered surface of wall and making the surfaces smooth by applying 2mm thick wall care putty and applying two coats of oil emulsion distemper, complete all as specified and directed. 59 m&l for preparation of old surfaces of walls of any description after complete removal of existing treatment and making the surfaces smooth and applying two coats of cement base paint over a coat of alkali resistant primer including curing, complete all as specified and directed. 60 m&l for preparation of newly plastered surface of external wall and applying two coats of cement base paint over a coat of alkali resistant primer including curing, complete all as specified and directed. 61 hacking out old broken glass ( any thickness, size, quality or description ) from metal frames, glazed with putty or fixed with beads / clips, complete all as specified and directed. 62 s&f 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane, complete all as specified and directed. 63 s&f 3mm thick figured glass, pin head type in square not exc 0.50 sqm each pane, fixed with oil putty, complete all as specified and directed. 64 m&l for preparation of old surfaces of steel & iron work of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. 65 m&l for preparation of old surfaces of wood & wooden of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. 66 m&l for preparation of newly wood & wooden based surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of pink primer complete all as specified and directed. 67 s&f rotational moulded polyethlene water storage tank of capacity 500 litres, three layers ( cylindrical vertical with closed top ) , hoisted and fixed in position including 20mm dia pvc ball valve, high pressure with polythene float complete all as specified in ssr part 1, including dismantling of existing pvc water tank of any capacity complete all as specified and directed. 68 m&l for 15mm bore water tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. 69 m&l for 20mm bore water tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. 70 s&f as in repair15mm bore stop / angle valve, with flange cast copper alloy ( isi marked ) , chromium plated screwed down, high pressure with capstan head, screwed both ends, complete all as specified and directed. 71 s&f as in repair15mm bore stop valve, cast copper alloy ( isi marked ) , fancy type chromium plated with long shank and cup ( concealed type ) screwed down, high pressure with capstan head, screwed both ends, complete all as specified and directed. 72 s&fas in repair15mm bore pillar tap, cast copper alloy, fancy type, with capston head, chromium plated, screwed down, high pressure with or without letters, hot or cold with long screwed shank and fly nuts, screwed for iron pipe, complete all as specified and directed. 73 s&fas in repair 15mm bore bib tap with flange, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. 74 s&fas in repairchromium plated tubular towel rail, 20mm dia d type, 60cm long between flanges, complete all as specified and directed. 75 s&f as in repaircp shower rose of size 150mmx150mm with swivel arm, stainless steel / cp brass, including fixing to steel pipe or union complete all as specified and directed. 76 s&f as in repair jet spray ( with 1.50 mtr pvc tube ) , fixed to ewc and angular stop cock / valve, complete all as specified and directed. 77 s&f as in repair health foucet ( with 1.5mtr long pvc tube ) fixed to angular stop cock and complete wall hanging arrangement, complete all as specified and directed. 78 s&f as in repair bevelled edge mirror of size 600mm x 450mm of selected quality, 5mm thick glass with pvc frame with pvc beading, fixed with chromium plated brass screws and cup washers, complete all as specified and directed. 79 s&f as in repair ldpe waste pipe, 32mm dia suitable for whb / sink including threaded pvc socket suitable for shank of waste coupling, complete all as specified and directed. 80 s&f as in repair pvc connections 15mm size with ptmt nuts of length 450mm complete all as specified and directed. 81 s&f as in repair pvc ball valve, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20mm bore pipe, complete all as specified and directed. 82 s&f as in repair plastic water closet seat cover, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, complete all as specified and directed. 83 s&f as in repair pvc flushing cistern of 10 ltrs capacity including pvc inlet and outlet connections, brackets, pvc flush pipe with bend 32mm dia of suitable length including making necessary connections to water supply pipe line and jointing to wc, complete all as specified and directed. 84 s&f as in repair syphonic action kit for pvc flushing cistern of 10 ltrs capacity, complete all as specified and directed. 85 s&fas in repairvitreous china wash basin, white flat back of size 550mm x 400mm including 32mm size cp waste coupling full thread and 32mm dia pvc waste pipe, brackets and cutting for and pinning in ends of brackets or errecting stand, complete all as specified and directed. 86 s&f as in repair vitreous china wash down water closet pan ( pedestal pattern ) , white complete including fixing to trap including pvc seat and cover with hinging device for pedestal pan and connecting etc, complete all as specified and directed. 87 s&f as in repair vitreous china squatting pan of orissa pattern of size 580mm x 440mm, white with ci ‘p’ or ‘s’ trap, front or back inlet and foot rests of any pattern ( including fixing of flush pipe ) and connecting etc. including provision of cement concrete bedding, complete all as specified and directed. 88 s&fas in repair kitchen plate rack made of stainless steel 1mm thick, fixed on wall with plugs, mild steel screws overall size 750mm x 900mm size complete all as specified & directed. 89 s&fas in repair sink with drainage board made of stainless steel 1mm thick, fixed with plugs, washers including pvc waste pipe, waste couplingincluding bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting to union pipe, overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm, complete all as specified & directed. 90 s&f as in repair stainless steel grating doom 100mm dia, fixed in floors complete all as specified and directed. 91 s&f as in repair stainless steel grating doom 100mm dia with waste hole, fixed in floors complete all as specified and directed. 92 s&f as in repair 75mm bore pvc ( swr ) pipes, single socketed, in any length with rubber ring joints, laid or fixed in trenches / floors / walls, complete all as specified and directed. 93 s&f as in repair 110mm bore pvc ( swr ) pipes, single socketed, in any length with rubber ring joints, laid or fixed in trenches / floors / walls, complete all as specified and directed. 94 s&f as in repair 75mm bore pvc ( swr ) bend, plain including jointing with solvent cement, complete all as specified and directed. 95 s&f as in repair 110mm bore pvc ( swr ) bend, plain including jointing with solvent cement, complete all as specified and directed. 96 s&f as in repair 75mm bore pvc ( swr ) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed. 97 cleaning and removing all scale and dirt etc. from water tank and from mouths of circulating pipes without disconnecting tank of capacity exc 500 ltrs but not exc 1000 ltrs, complete all as specified and directed. 98 cleaning and removing all inaccessible roof and wall vegitation and plants after cutting & removing from roots and removing the same out of mod land complete all as specified and directed. 99 demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 100 demolition of stone set paving of any description laid, bedded in any mortar complete all as specified and directed. 101 taking down chowkhats or framesexc 1.5 sqm but not exc 4.0 sqm each ( without taking off shutters from the frame ) , complete all as specified and directed. 102 taking down chowkhats or frames not exc 1.5 sqm each with shutter ( without taking off shutters from the frame ) , complete all as specified and directed. 103 taking down shutters of any description exc 1.0 sqm but not exc 2.0 sqm each, complete all as specified and directed. 104 dismantling timber scantling 40 sqm and over in section in unframed work etc complete all as specified and directed. 105 taking down roof trusses, coupled rafters or trussed beams, above 4m but n. exc. 8m length clear span complete all as specified and directed....

Military Engineer Services - Punjab

33523815 comprehensive maintenance of c arty bde under age b / r ( p 1 ) at faridkot mil stn 1 taking down 15mm dia bib cock/stop cock of any pattern / type and re fixing the same after minor repairs such as replacement of washers etccomplete all as specified and directed. note : any major parts such as jumbers brass/ spindles / caps etc to be measured as supply only and paid for separately. 2 s&f in repair pvc connections 15 mm size with ptmt nuts of length 450 mm complete all as specified and directed. 3 s&fin repair 15mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for gi outlet/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed. 4 all as per srl item no. 05 here in before but chorminium plated complete all as specified and directed. 5 all as per srl item no. 05 here in before butchromium plated with long shank and cup (concealed type) complete all as specified & directed. 6 s&f in repair 20mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for gi out let/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed. 7 s&f in repair 15mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down of iron pipe or for brass ferrule and fixed complete all as specified and directed. 8 s&f in repair 15mm bore bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down of iron pipe or for brass ferrule and fixed complete all as specified and directed. 9 s&f in repairpillar taps,fancy type,chromium plated ,cast copper alloy, with capstan head, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe of 15mm bore complete all as specified and directed 10 s&f in repair 15 mm bore ptmt ball valve, high pressure with epoxy coated aluminium rodand high density plastic ball,screwed for iron pipe and fixed in position complete all as specified and directed . 11 s&f in repair 20 mm bore ptmt ball valve (float valve), high pressure with epoxy coated aluminium rodand high density plastic ballscrewed for iron pipe and fixed in position complete all as specified and directed. 12 s&f in repair 25 mm bore ptmt ball valve (float valve), high pressure with epoxy coated aluminium rodand high density plastic ballscrewed for iron pipe and fixed in position including all necessary fittings complete all as specified and directed. 13 s&f in repair pvc waste pipe, 32 to 40mm for whb/sink /urinal up to floor trap and fixed complete all as specified and directed. 14 s&f in repair stainless steel grating of any size (as per existing)with or without waste hole completeall as specified & directed. 15 s&f in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 ltr capacity,trippled layered, hoisted and fixed in positionincluding ptmt float valves, high pressure, with polythene ball & float and fly nut , screwed for 20mm bore iron pipe complete all as specified and directed. 16 s&f in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 ltr capacity,trippled layered, hoisted and fixed in positionincluding ptmt float valves, high pressure, with polythene ball & float and fly nut , screwed for 20mm bore iron pipe complete all as specified and directed. 17 s&f in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 2000 ltr capacity,trippled layered, hoisted and fixed in positionincluding ptmt float valves, high pressure, with polythene ball & float and fly nut , screwed for 20mm bore iron pipe complete all as specified and directed. 18 s&f in repair covers for pvc overhead water tanks of any capacity (as per sample) complete all as specified and directed. 19 s&f in repair vitreous china wash hand basin, white, flat back of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including brass chromium plated waste coupling 32mm bore, waste pipe pvc 32mm bore, pillar taps,fancy type,chromium plated ,cast copper alloy, with capstan head, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe of 15mm bore and pvc connection 15mm size, 450mm long with ptmt nut and other end fixed complete all as specified and directed. 20 s&f in repair gi tubing, 15 mm bore, medium grade with all fittings,fixed to walls/ceiling or laid in floor complete all as specified and directed. 21 s&f in repair gi tubing, 20 mm bore, medium grade with all fittings,fixed to walls/ceiling or laid in floor complete all as specified and directed. 22 m&l for removing blockage/air in old gi tubing of any size upto 25mm and of length less than 6 mtr including taking down ,use of pump if required and re fixing in the same locationafter making pipe functional complete all as specified and directed. 23 m&l for removing blockage/air in old gi tubing of any size upto 25mm and of length greater than 6 mtr including taking down ,use of pump if required and re fixing in the same locationafter making pipe functional complete all as specified and directed. 24 s&f in repairswivel shower of ptmt, of any colour for fixing with 15mm pipe, (minimum weight 40 grams) complete all as specified & directed. 25 s& f in repairs shower arm 15mm size, 195mm long with bend of 45 degree with flange of ptmt any colour including fixing to steel pipecomplete all as specified and directed. 26 s&f in repair 15mm dia, brass chromium plated wall mixer for mixing hot & cold water, screwed down for iron pipe complete all as specified and directed . 27 s&f in repair pvc syphon (as per sample) for pvc low level flushing cistern of capacity 10 ltr omplete all as specified and directed . 28 dismantling ci/pvc pipe of 75/100mm dia alongwith fittings ,below or above gl/laid in floors/fixed to walls jointed in cement mortarcomplete all as specified and directed. 29 s&f 75mm bore pvc (swr) pipes ,single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 30 s&f 110mm bore pvc (swr) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 31 s&f in repair pvc (swr) floor trap, 75 mm dia, plain with stainless steel grating including jointing with solvent cement complete all as specified and directed 32 s&f in repair pvc (swr) p trap of 110mm bore complete all as specified and directed 33 s&f in repair vitreous chinasquatting pan orissa pattern, size 580mm x 440mm white / coloured, with integral foot rest including flush pipe and connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floorscomplete.all as specified and directed. 34 s&fin repair vitreous china wash down water closet pan (pedestel pattern/ewc/long pan) white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern, anti syphonage pipe with pvc flush pipe of 32mm dia including plastic seat with cover,white in colour with mild steel chromoum plated hinging and p or s trap device complete all as specified and directed. 35 s&f in repair pvc low level flushing cistern, white, 10 litre capacity, valveless syphonic action type with float, handle includingbracketcomplete all as specified and directed . 36 s&f in repair pvc knob/handle (as per sample) suitable for 10 ltr capacity pvc low level flushing cistern complete all as specified and directed. 37 s&f in repair vitreous china urinal ,flat back of size 465x355x265mm, white,waste coupling of ptmt including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar, including connections to flushing pipe and outgoing pipes,32mm boe flush pipe & half turn valve 15mm bore complete all as specified & directed . 38 s&f in repair chromium plated jet spray with 1.50 m long flexible tube andfixed complete all as specified and directed. 39 s&f in repair chromium plated brass health faucet with 1.0mtr tube & hook (braided tube) complete all as specified and directed. 40 s&f in repair plastic water closet seat cover, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and fixed complete all as specified and directed. 41 s&f in repair flush pipe of polythene of low or high density or pvc, 32mm dia, for low level flushing cistern and fixed complete all as specified and directed. 42 s&f in repair waste fittings 32 mm /40mm brass chromium plated for glazed ware sinks, basins etc.with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. 43 s&f in repairsinks with drainage board, madeof 1mm thick stainless steel,overall size of sink 915mm x 460mm with bowl size 410mm x 330mm x 160mm,plugs, washers, waste pipe, union, waste coupling and cantilever brackets embedded in cement and sand mortar in wall complete all as specified and directed 44 s&f in repairs toilet paper holder brass finish glossy fixed to walls with chromium plated (cp) brass screwscomplete all as specified and directed. 45 taking down wooden shutters of any description exc 1 sqm and n. exc 2 sqm each and refixing in the same opening after easing, adjusting and also refixing of builders hardware as required including renewal of unserviceable screwsetc complete all as specified and directed. 46 s&f in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tined tacks or galvanized wire staples or wooden bead complete all as specified anddirected. 47 s&f in repair 100mm long mild steel butt hinges, medium weight, cold rolled(isi marked)fixed with screws complete all as specified and directed. 48 s&f in repair butt hinges 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type b 21 (isi marked)fixed with screws complete all as specified and directed. 49 s&f in repair brass mortice lock, vertical type, size 100 mm, 2 levers complete all as specified and directed. 50 s&f in repair 250 mm long aluminumalloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloycomplete all as specified & directed. 51 taking down existing aluminium frame shutters of any description exc 1 sqm and n. exc 2 sqm each and refixing in the same opening after making necessary repair etc complete all as specified and directed. 52 s&f in repair 150mm size (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring,fixed in floor complete all as specified and directed. 53 s&f in repair door closer hydraulically regulated, aluminium (diecast body), designation no 2, universal type suitable for door shutter 700mm to 850mm width and weight between 36 to 60 kg complete all as specified and directed. 54 s&f in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made out of mild steel heavy duty & fixed complete all as specified and directed. 55 hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads and fixed complete all as specified 56 m&l for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with wooden beads (supplied alongwith shutters) in squares n.exc 0.5 sqm in each pane complete all as specified and directed. 57 m&l for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with wooden beads (supplied alongwith shutters) in squares exc 0.5 sqm in each pane complete all as specified and directed. 58 m&l for 3 mm thick, frosted sheet glass, ordinary quality and glazing with oil putty or with wooden beads (supplied alongwith shutters) in squares n.exc 0.5 sqm in each pane complete all as specified and directed. 59 m&l for 4.8 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with wooden beads (supplied alongwith shutters) in squares exc 0.5 sqm in each pane complete all as specified and directed. 60 m&l for securing glass of any description in existing metal frame glazed with putty / beads including removing loose or decayed putty / beads, painting / oiling one coat on rebates, grooves, reputtying and painting / oiling puttied surface to match existing work (new length of frame reputtied shall be measured) complete all as specified and directed. 61 s&f looking mirror of 5mm thick selected quality glass, size 600mmx450mm, bevelled edge,mounted on 6mm thick commercial plywood or hard board covered with 25mm wide pvc/wooden frame moulding and teak wood beading all around and fixed to wallwith chromium plated brass screws and cup washes complete all as 62 s&f in repairbrass chromium plated tubular towel rail 20mm dia, d type, 600mm long between flanges fixed with cp brass screwsincluding wooden/plastic beads complete all as specified and directed. 63 s&f in repair ptmt cabinet with mirror of size 330x430mm complete all as specified & directed. make: prayag cat no. 551 or equivalent in polytuf / pearl/ shakti as approved by ge 64 taking down of chowkats or frames n.exc 1.5 sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed. 65 taking down of chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed. 66 taking down shutters of any descriptionexc 1 sqm and n. exc 2 sqm each complete all as specified and directed. 67 s&f pressed steel rectangular frames,of size of frame 105x60 mm fordoors with one or more rebates , including necessary fixing lugs, hinges, lock strike plate over a shop coat of zinc chromate primer complete all as specified and directed. 68 s&f pressed steel rectangular frames,of size of frame 125x60 mm fordoors with one or more rebates , including necessary fixing lugs, hinges, lock strike plate over a shop coat of zinc chromate primer complete all as specified and directed. 69 m&l forpcc 1:3:6, type c0 (using 12.5mm graded crushed stone aggregates) as in back filling of pressed steel frames, bed blocks, fixing of hold fasts etc including necessary formwork complete all as specified and directed 70 s & f solid pvc door frame of size 50x47mm, made out of 5mm plain coloured pvc sheet reinforced with ms square tube complete all as specified and directed. 71 s&f factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out ofms tubes for top and bottom rails, ms frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width & stick inside withsolvent cement forstile and plaincolour pvc sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail.paneling of plain colour pvc sheet to be fitted in the ms frame welded/sealed to the style and rail with suitable pvc sheet beading and joined together with solvent cement supplying and fixing in the frame at site complete all as specified and directed. 72 s&f 35 mm thick,2nd class hard wood, plain framed panel shutters (any number of panels) with panels of timber flat on both sides (feather edges) or of vaneered partical board medium desnsity, wood partical board with commercial face veneers, fitted to chowkats complete all as specified and directed . 73 s & factory made 35mm thick, 2nd class hardwood (hollock), glazed and skeleton shutters, open rebatedand prepared to receive gauge /gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members as specified in clause 8.24 (a) of mes schedulepart i section 8 complete all as specified and directed. 74 fixing only shutters of any descriptionexc 1 sqm and n. exc 2 sqm each complete all as specified and directed. 75 m&l for preparation of new or previously untreated surfaces of wood or wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 76 s&f galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tined tacks or galvanized wire staples or wooden bead complete all as specified anddirected. 77 s&f 300mm mild steel, ordinary rat tail spring(helical door spring) including roller androller plate complete all as specified and directed. 78 s&f in repair 300mm mild steel, ordinary rat tail springincluding roller androller plate complete all as specified and directed. 79 s&f 250 mm long aluminumalloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloycomplete all as specified & directed . 80 s&f 150mm size, aluminiun anodised barrel tower bolts of extruded section complete all as specified & directed. 81 s&faluminium handle of size 125mm,fabricated type, anodised complete all as specified & directed. 82 s& fbutt hinges of size 100mm , medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed. 83 s&f factory made box type steel window with side hung shutters including box type hinges with steel handle and 2 nos 150mm long mild steel tower bolt,fixing lugs etc complete with glazing bars dovetailed or weldedand with one shop coat of zinc chromate primer complete all as specified and directed. 84 s&f factory made box type steel window with side hung shutters including box type hinges with steel handle and 2 nos 150mm long mild steel tower bolt,fixing lugs etc complete without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed. 85 m&l for steel framedworksuch as grills, gratings, etc, with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; frame work of water tanks and similar work conforming to fe 290. gde e 165 complete all as specified and directed . 86 m&l for preparation of new or previously untreated steel surface of any description over 10 cm in width or girth and applyingtwo coats of synthetic enamal paintcomplete all as specified and directed. 87 s&f in repair ms powder coated decorative drapery rod (colour as approved)20mm dia of approved pattern & design including decorative knobs (wall side and free side) & powder coated mild steel flat iron brackets fixed with steel screws & pvc rawl plugs/grips complete all as specified and directed. 88 dismantlingwall and ceiling boards (fibre,pulp, insulation) or insulation boards/slabs/blankets, any thickness, including cover fillets etc complete all as specified & directed. 89 s&f 7mm thick gypsum board as in ceiling fixed with screws as permanufacturers instructions, including anodised aluminium snap grid frame work for false ceiling of grid 605x605mm,hangers 6mm dia (upto 1200mm length)adjusting level fixed to roof slab by means of ceiling cleats made of gi flat 40x3mm size & length 60mm andexpansion hold fasterners 12.5mm dia,40mm long complete all as specified and directed. note: quoted rate of the item deemed to be included for taking down and refixing (as per existing)minor electric fittings and fixtures (if any) on the surface of ceiling 90 s&f pvc hollow wall lining interlocking type of 7mm thick plain/coloured /wood grain fitted in to the wall with pvc rawl plug and steel screws including fillets on joints as per manufacturers instruction etc.complete all as specified and directed. note: quoted rate of the item deemed to be included for taking down and refixing (as per existing)minor electric fittings and fixtures (if any) on the surface of wall 91 s&f solid pvc wall lining consisting of 5mm thick wood grain printed pvc sheet having beading/border on top and on joints inclusive of solvent cement and fixing at site on pvc frame as per specifications and drawings all as specified and directed by engineer in chargenote: quoted rate of the item deemed to be included for taking down and refixing (as per existing)minor electric fittings and fixtures (if any) on the surface of wall 92 s&f 5mm thick pvc sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make pvc frame as per specification and drawing all as specified and directed . 93 demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified anddirected 94 m&l for providing precast cement concrete 1:3:6, type c 0 (using 12.5mm graded crushed stone aggregates)as in louvers and jallies in between pillars, 40mm thick (measured solid) including all moulding but excluding frame and set in cement mortar 1:4complete all as specified and directed. 95 demolition of brickwork or stone/boulder masonry,built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed 96 m&l for brick work with sub class b bricks, straight or curved on plan, exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. 97 m&l for taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 98 m&l for rendering 15 mm thick in cement mortar 1:4 on brick work or concrete surfaces finished even and smooth without using extra cementcomplete all as specified and directed . 99 m&l for rendering 15 mm thick in cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cementcomplete all as specified and directed . 100 m&l for 5mm thick rough cast plaster over and including 10mm thickrendering in cement mortar 1:4 on fair faces of brick or concrete surface completeall as specified and directed .note : the rough cast mixture shall consist of crushed stone / fine gravel aggregate, coarse sand & cement in the ratio of 1:1:1 over the rendering coat. 101 m&l for rendering 10 mm thick in cement mortar 1:4 on ceiling, finished even and smooth without using extra cement complete all as specified and directed. 102 m&l for preparation of newly plasteredsurfaces of wallsand applying two coats of cement base paintcomplete all as specified and directed. 103 m&l for preparation of newly rough cast plastered surfaces of walls and applying two coats of cement base paintcomplete all as specified and directed. 104 m&l for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over chalk whitening complete all as specified and directed. 105 m&l forpreparation of new surfaces plastered of walls and applying two coats of white wash on wall complete all as specified and directed. 106 m&l for preparation of new surfaces plastered of ceiling and applying two coats of white washcomplete all as specified and directed. 107 dismantlingfloor,hearth or wall tilling including cement mortar bedding (but not backing)and rubbish of the premises complete all as specified and directed. 108 s&f non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular)area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying finishes complete all as specified and directed 109 s&f non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular)area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying finishes complete all as specified and directed 110 m&l for coloured glazed ceramic tile 450x300x7 mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. 111 m&l for coloured glazed ceramic tile 300x200x7 mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. 112 m&l for vitrified ceramic tiles, light shade,10 mm thick (square/ rectangular), area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed in cement mortar 1:6 and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. 113 dismantling stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, skirting, aprons etc complete all as specified and directed. 114 m&l for machine cut kota stone slab,20 25 mm thick as in flooring , set and jointed in cement slurry over & including screed of 20 mm thick in cement mortar 1:6 andpointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified & directed. . 115 all as per ser item no 114 here in before but except kota stone complete all as specified and directed. 116 s&f machine cut kota stone slab 20 25 mm thick as in skirting, set and jointed in cement slurry over & including10 mm thick rendering in cement mortar1:4 and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified and directed . 117 m&l for granite (of any type)machine cut, 20mm thick, bedded and jointed with grey cement slurry over and including screed of 20mm thick in cement mortar 1:6 and pointed with white cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror polishing complete all as specified and directed 118 m&l formarble work 18mm to 20mm thick of any shade (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointed in white cement (1:2) using marble dust with admixture of pigment to match the shade of the marble over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 119 m&l for cutting, rubbing and polishing of existing kota stone/mosaic flooring complete all as specified and directed. 120 demolition of cement concrete (un reinforced) in ground floor and paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed. 121 m&l for 25mm thick plain cement concrete 1:2:4 type b 0 (using 12.5mm graded crushed stone aggregates)as in flooring complete all as specified and directed 122 m&l for plain cement concrete 1:4:8, type d 2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed. 123 m&l pcc 1:2:4 type b 1 (using 20mm graded crushed stone aggregates) as in coping,bed blocks and similar worksincluding slightly rounded or chamfered angles including necessary formwork complete all as specified and directed. 124 m&l for sand filling under floor 25mm thick with washed and screened dry fine river sand including watering, well ramming and consolidation complete all as specified and directed . 125 m&l for machine pressed precast concret interlocking paver block, any shape and size, conforming to is 15658 2006 of 60 mm thickness, m 35 grade with grey cement andpigment all as specified and directed . 126 all as per ser item no 125 here in before but except paver blockscomplete all as specified and directed. 127 taking down shutters of any descriptionn.exc 1 sqmeach complete all as specified and directed. 128 m&l for 2nd class hardwood plain fillets ,exc 13 sqcm and not exc 25 sqcm sectional area,square, rectangular or triangular in section, clean swan, secured with nails or brads complete all as specified and directed. 129 m&l in repair 18 19mm prelaminated particle board,interior grade,prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. 130 s & f30mm width continous (piano) hinges, mild steel, bright finish or electro galvanisedfixed with screws complete all as specified and directed . 131 s&f brass locks for cup board,grade 1,size 75mm,4 livers having minimum two keys complete all as specified and directed . 132 taking down carefully unserviceable/ old rolling shutter (manual/gear operative) of size upto 15 sqm, denting the surfaces as required, cleaning the guide rails, laths, top cover with the help of kerosene and greasing & oiling properly to make the system smooth /easy functional including supply and fixing new nuts and bolts as per existing size by removing old rusted nuts and bolts, necessary welding (wherever required as directed)giving proper tension tothe spring and refixing the shutter and gear box inthe same opening after repair work andmaking good the damaged brick/concrete works to the existingincluding painting with one coat of synthetic enamel paint on both sides of shutter complete all as specified and directed . 133 taking down carefully unserviceable/ old rolling shutter (manual/gear operative) of size exceeding 15 sqm but not exceeding 30 sqm, denting the surfaces as required, cleaning the guide rails, laths, top cover with the help of kerosene and greasing & oiling properly to make the system smooth /easy functional including supply and fixing new nuts and bolts as per existing size by removing old rusted nuts and bolts, necessary welding (wherever required as directed)giving proper tension tothe spring and refixing the shutter and gear box inthe same opening after repair work andmaking good the damaged brick/concrete works to the existingincluding painting with one coat of synthetic enamel paint on both sides of shutter complete all as specified and directed . 134 taking down unserviceable/ broken/ rusted rolling shutter ofsizen exc 25 sqm and removing from site complete all as specified and directed. 135 s&f steel rolling shutters having thickness of lath 1 mm, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple, bracket plates, clamps, pulley, spring, shaft, hold fast, stopper, pulling hook and other allied parts complete includingone shop coat of primer; erected in position as indicated, push pull or manual type complete all as specified and directed. 136 s&f in repairs hood covers made out of 1.00 mm thick mild steel sheetincluding bending the sheet to the required shape and fixing the same to the rolling shutter bracket plate complete all specified and directed . 137 s&f safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. 138 s&f in repairs mild steel gear box assembly (with ms rod and handle)including connecting and fixing the gear box to wall with 4 nos hexagonal bolts of 10 mm dia and 100 mm longafter cutting into existing wall/pillar of brick work/rcc and filling back with pcc complete all as specified and directed . 139 s&f in repairs mild steel gear handle for gear operated rolling shutters complete all as specified and directed . 140 s&f in repairs mild steel helical wire springs (conforming to is 6248 1970) forrolling shutters of size upto 30 sqm complete all as specified and directed . 141 s&f in repairs interlocking lath section formed from rolled mild steel strips for rolling shutter (of existing width ) 1.00 mm thick inclding two coats of synthetic enamel paint over a coat of primer on both sides complete all as specifed and directed . 142 m&l for applying one coat of synthetic enamel paint on old painted steel surface of any discription over 10cm width or girth after prepration of surface complete all as specified and directed 143 raking out joints/pointing in cement mortar to brick work in walls or to bricks on edge in floors,surface channels,roofs etc complete all as specified and directed 144 m&l for flush pointing to brick work in cement mortar 1:3complete all as specified and directed . 145 supply only integral water proofing compound complete all as specified and directed . 146 dismantling of bricks laid, (laid flat or on edge) or brick tiles in floors, roof, channels, kerbs, aprons etc bedded and pointed in any mortar (each layer) complete all as specified and directed. 147 m&l for 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cementcompleteall as specified and directed . 148 all as per item no 147 here in before above but except brick tiles completeall as specified and directed . 149 demolition of concrete (un reinforced) as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas, roof staging,sunken areas and similar suspended work complete all as specified and directed. 150 m&l for plain cement concrete 1:2:4 type b 0 (using 12.5 mm graded crushed stone aggregates) as inroof kerb, mud stopsbands, copings,bed plates including weathering, slightly rounded or chamfered angles including necessary form work for pipe support, finished even and smooth without using extra cement complete all as specified and directed 151 m&l for taking down cement or lime plaster of roof including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 152 m&l for 15 mm thick screed bedin cement mortar 1:3 for laying floor finishes with water proofing compound complete all as specified and directed .note: wpc shall bemeasured and paid seperately.note : a sum of rs. 43,278.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. please refer detail on srl page no. 28 & 29 (schedule of credit) of tender documents. ...

Indian Army - Punjab

31383467 bids are invited for engine holding stand , mesh carrier , grasping stand , mua holding stand , radiant lockup mount , engine testing structure , mount for ejector stand , cantilever bar , crest plate stand , saucer shape air cleaner mount , jack standfor axle arm , iron mounting carrier , oil container dip tray, trapezoidal depression crate , upper structure mount ,pneumatic cleaner for base total quantity : 31...

Ministry Of Defence - Punjab

30755027 bids are invited for 4 mp ip ir bullet camera , nvr, 16 channel video inputs, support h.265/h2.65 video format , d link dgs 1008p 8 port gigabit poe unmanaged switch (metal housing) , d link dgs 1005p 4 port gigabit poe unmanaged switch (metal housing) , d link dgs 1005p 4 port gigabit non poe unmanaged switch (metal housing) , 6tb hdd , cat utp cable pvc conduit and accessories , 19 inch 9u 500 mm outdoor wall or pole mount rack with pdu 5 hardware pk 20 01 cantilever shelf , 19 inch 4u 500 mm outdoor wall or pole mount rack with pdu 5a 6soc 01 mounting hardware pk 20 01 cantilever shelf 01 , cable termination box for camera , 5amps switch & socket with plate & pvc back box 1 nos , 3 core 1.5 sqmm armed copper power cable ,slicing of 06 port fiber liu loaded with single mode 3xscpxdx adapters & splice trays , slicing of 12 port fiber liuloaded with single mode 6xscpx dx adapters & splicetrays , 6 core single mode armored ofc cable with pvc &accessories , fast ethernet sfp to rj45 fiber mediaconverter/ fiber to ethernet converter 10/100mbps rj45port to 100 base fx single mode fiber. , sc sc single modeofc patch cord , 1kva online ups with 30 min back upvoltage range 110vac (+/ 5%) 300 vac, frequency range40 hz 70hz face single face with ground , fixing of displayat two locationboq title installation and commissioning of cctv system total quantity : 1199...

Military Engineer Services - Punjab

29822669 provision of certain sanctioned works at mil stn suranussi under ge kapurthala provn of certain sanctioned works at mil stn suranussi under ge kapurthal a demolition of brick work built in cement mortar , including all quoins arces etc 2 dismantling of asbestos cement ( corrugated, semi corrugated etc ) sheets in roof coverings 3 demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick above or below ground level. 4 dismantling wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets. 5 dismantling, mild steel work of any description not otherwise provided for complete all as specified 6 demolition of cement concrete in roofs, floors ( other than ground floors ) , beams, staircases, landing, chajjas and similar suspended work. 7 dismantling boarding, any description, fixed in any position with screws complete all as specified and directed. 8 taking down cement or cement lime plaster of any description from walls, including racking out joints hacking for key scrubbing down with water etc , complete all as specified. 9 removing old lime wash ( if any ) , hacking for key, raking out joints of old brick work or stone work built in cementmortar; not previously plastered; and scrubbing 10 taking down chowkats or frames with shutters ( without taking off the shutter from the frame ) of area n.exc 1.50 sqm each and removing from site. 11 all as per items no 10 above but area exc 1.50 sqm but n.exc 4.00 sqm 12 m&l for brick work , with sub class b bricks built in cement mortar 1:6 straight or curved on plan exc 6mtr mean radius with old size bricks 13 m&l for 15mm thick cement plastering in cement mortar ( 1:6 ) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified. 14 m&l for 15mm thick cement plastering in cement mortar ( 1:4 ) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified. 15 m&l for 5 mm thick rendering in cement mortar in 1:3 on ceiling finished smooth without using extra cement. 16 m&l for preparing surfaces new of walls and applying two coats oil bound distemper over a coat of alkali primer 17 m&l preparing surfaces new of walls and applying two coats of cement base paint over a coat of alkali primer 18 m&l forpreparation of old plastered or unplastered wall surfaces and applyingone coat of oil bound distemper complete all as specified and directed. 19 m&l for preparation of old painted wooden surfaces of any description over 10 cms width or girth and applying two coat of synthetic enamel paint on wooden surfaces complete. 20 m&l for preparation of old painted steel surfaces of any description over 10 cms width or girth and applying one coat of synthetic enamel paint on steel surfaces complete all as directed. 21 s & f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with j type hooks as specified. 22 s & f pre painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with j type hooks as specified. 23 m&l for 20 25 mm thick machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, over and including 20 mm thick screed or bedding layer in cm 1:4 24 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing servicable tiles to store and rubbish off the premises complete all as specified 25 m&l for non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed inneat cement slurry and pointed in white or coloured cement to match , over and including15 mm thick screed or bedding layer in cm 1:4 26 m&l for glazed ceramic coloured tiles ( 300x200 ) mm & 7mm thick on vertical surfaces of walls set and jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified and directed. 27 m&l for 25mm thick cement concrete type b 0, 1:2:4 using 12.5 mm graded stone agg as in levelling course. 28 m&l for hardcore of broken bricks of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface 29 m&l for 75 mm thick cement concretetype c 2, 1:3:6 as in plinth protection with using 40 mm graded stone aggregate 30 m & l for perforated particle board / tiles 12mm thick for insulation and acoustic purpose 60 x 60cm size fixed with screw to aluminium frame work or staples on snap grid in ceiling complete all as specified and directed by engineer in charge. 31 s & f anodised aluminium snap grid frame work for false ceiling complete all as specified and directed by engr in charge. 32 s&f framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening conforming to gdefe 290 ( gde e 165 ) 33 s & f 35mm thick iind class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in ssr part – i, section – 8, clause 8.24 ( a ) ; supplied and fitted to chowkats all as specified and directed by engineer in charge . 34 s&f300 mm long ordinary helical door spring , fixed to doors with screws 35 s & f mild steel sliding door bolt 300mm long clip type, stove enamelled black with bright bolt not less than 16mm dia complete. 36 s & f mild steel200mm long, barrel tower bolt stove enameled black with bright bolts. 37 s & f mild steel pressed handle oval type stove enameled black of size 150mm. 38 s & f mild steel butt hinges cold rolled of size 100mm medium weight. 39 m&l for preparing new surfaces of steel and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. 40 m&l for preparing new surfaces of wood and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. 41 s&f in replacement 20 mm dia harrison rails mild steel with decorative finish , with fixing brackets , stops, rollers complete all as specified and as directed ( two brackets per 1.5 m length and 08 nos roller per 1.rm ) 42 m / l for 600x450mmbevelled edged mirror of selected quality glassmounted on ac boardfixed to wooden plug with chromium plated screws screedbed in cm ( 1;6 ) 43 s&f in repairs vitreous china urinals, flat back of size 465mmx355mmx 265mm, white with grating and union for discharge pipe including connecting to waste pipe complete all as specified and directed. 44 s&f in repairs pvc flushing cistern, 10 ltr capacity, valve less symphonic action type, low level, with intel, ball valve, float valve and handle including brackets fixed in position, 32 mm dia pvc flush pipe and connection to water mains complete all as specified and directed by engineer in charge. 45 s& f in repair vetrious china wash hand basin flat back550x400mmincluding fixing bracket, pvc waste coupling and waste pipe, cp pillar tap etc all as specified and directed by engineer in charge. 46 taking down gi tubing and connections with all fittings 15 mm bore 47 ditto all as per item 46 above but 20mm bore 48 s&fin repairs15 mm dia gi tubing , medium grade, and connections fixed to wall or ceiling, laid in floor etc complete all as specified and as directed by engineer in charge. 49 s&fin repairs20 mmdia gi tubingand connections fixed to wall or ceiling, laid in floor etc complete all as specified and as directed by engineer in charge. 50 s&f pvc connections 15mm size with ptmt nuts of length 600 mm and all as specified and directed make : prayag. 51 s&f in repair bib taps , 15mm dia cast copper alloy chromium plated , with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferruleand all as specified and directed. 52 s&f in repair stop valves15 mm , cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed. 53 ditto as per item no 52 above but 20 mm dia 54 s&f in repair pillar taps15mm dia , cast copper alloy , with capstan heads , chromium plated , screwed down high pressure , with long screwed shanks and fly nuts , screwed for iron pipe and all as specified and directed. 55 s&fin repairsrotational moulded polythene water storage tanksdouble layer ( cylinder each vertical with closed top ) of capacity 500 itrs, hoisted and fixed in position including pvc float valve 20mm size, specified in ssr pt 1 make : sintex / frontier / polycon complete all as specified and as directed 56 s&fin repairs110 mm dia pvc swr type bends any radius complete all as specified 57 s&fin repairs75 mm dia pvc swr type bends any radius complete all as specified 58 s&fin repairs100 dia ptmt grating doom ( min wt 25 gms ) complete all as specified 59 s&fin repairs100mm borecast ironpipe fixed to wall and jointed with cement joints alla s specified. 60 s&f anodised aluminium frame powder coated with minimum thickness of powder coating 50 micron for doors, windows, ventilators with one or more rebates including joining cleat for fixing, hinges etc. complete all as specified and directed. note: prelaminated partical board and sheet glass / wiremesh shall be measured and paid for separately. make: indal / hindalco / jindal or equivalent as per is. 61 s&f anodised aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, handles, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. 62 s&f aluminium body ( die cast ) body, in door closer hydraulically regulated, designation no 3, universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed 63 s&f 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in squares exc. 0.5 sqm in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and as directed 64 ditto all as item 63 above but exc 0.5 sqm complete all as specified. 65 s & f 40mm thick solid pvc sandwich panel with l mm printed pvc sheet on both sides suitably fixed in aluminium frame work as per specification & drawing 66 s & f aluminium anodised barrel tower bolt of extruded section 150mm long ( isi marked ) . 67 s&f 30mm thick factory made pvc door shutter solid panel consisting of frame made out of ms tubes for top & bottom rails .ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc strip of 20mm width stuck inside with solvent cement for stiles and plain colourpvc sheet for top rail , lock rail &bottom rail on eitherside& as gap insertfor top rail & bottom rail . panellingof plain of plain colurpvc sheet to be fitted in the ms frame welded / sealed to stiles & rails with suitable pvc sheet beading and joined together with solvent cement , etc all as specified and shown on drawings complete all as specified and as directed complete all as specified and directed by engr in charge. 68 m&l for 35 mm thick , factory madeplain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 ( part i ) , kiln seasoned and chemically pressure treated 69 material and labour for 20cmx20cmx25mm thick coloured chequred cement concrete tiles with grey cement and pigment, set, jointedand pointed neat cement slurry in floors , paths and aprons etc laid over and including 15mm thick cement screed or bedding layer in cement mortra ( 1:6 ) complete all as specified and directed by the engineer in charge. 70 matarial and labour for cement concrete ( 1:2:4 ) , type b 1 ( using 20mm graded crushed stone aggregate ) as in coping, benching like works complete all as specified & directed by the engineer in charge. 71 s&f sinks made of stainless steel 1mm thick with drainage board kitchen or laborotory with plugs , washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe , over all size 915mm x 460mm. 72 s&f 3mm thick sheet glass ordinary quality glazing with oil putty in square n.exc0 .50 sqm in each pane 73 s&fgalvanized mild steel wire cloth 0.56 mm dia of wire and average width of aperture 1.18mm 74 hacking out of old broken glass ( any thickness &size quality or description ) from wooden frame glazed with putty or fixed with wooden beading & s&f 3 mm thick sheet glass plain ordinary quality and glazing with oil putty in squarenot exc. 0.50 sqm in each pane complete. 75 disconnecting existing water storage tank of any type and capacity exc. 250 ltrs and not exc. 500 ltrs and removing from site complete. 76 s&f in repair 20mm bore ball valve high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete fixed as in repairs. make : paryag. 77 s&f in repair plastic seat cover white closed pattern with flat bottom and ms chromium plated or aluminum hinges devicefor ewccomplete all as specified. 78 s&f in repair health focet for ewc 79 s&f in repairs vitreous china water closet padestal pattern ( white ) includng p or s trap but excluding fixing bolts, flushing cistern and flush pipe complete all as directed. 80 s&f in repair vitreous china ware water closet orissa pattern including connecting to trap and to flushing pipe anti syphonage pipe etc complete , fixed as in repairs of size 580mm x 440mm complete all as specified. make: hindware / cera / parryware. complete all as specified and as directed 81 s&f in repairs 19mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice laminated as in cupboard, shelves in kitchen etc complete all as specified and directed. 82 s & f hasps and staples with brass knobs 35 40mm dia 83 s & f 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished 84 s & f brass drawer handles, projection drop ( 50mm to 65mm ) on screwed plate complete all as specified. 85 supply & fixing for steel windows 1.25 mm thick box type ( primer coated ) erw hollow p section of size 60mm x 25mm single rebate comprises of skeleton shutter erw sec 50 x 20 mm & 1mm thick and openable leaf consisting two nos sash bar of t section 20x3mm complete welded to frame including cutting holes and making good dismanteled portion in cement concrete ( 1:2:4 ) type b i four nos for each window including following fitting welded to shutter complete glazed window all as specified and as directed by engineer in charge : ( i ) hold fast 150mm long 12 mm x 3mm made to shape 04 nos each window. ( ii ) handle of z section 20 x 25 mm, 100mm long 01 nos each leaf. ( iii ) ms tower bolt 150 mm long 02 nos each leaf. ( iv ) z section 20 x 25mm, 100 mm stopper 01 nos per leaf ( v ) cleat 55 mm long of hollow square 15x20x63mm welded to hinges 01 nos per leaf. ( vi ) ms box type hinges of size 75 x 12 mm 02 nos per leaf. ( vii ) ms guard bars square 12mm dia @10 cm c / c with gi frame fixed to window frame. ( viii ) fabrication and fixingnote : glass shall be measured and paid for separately. 86 ditto all as per item no 85 , but with gauged shutter. 87 s&f 3mm thick sheet glass ordinary quality glazing with oil putty in square n.exc0 .5sqm in each pane 88 s&fgalvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mm 89 dismantling brick tile or terracing tile single layer on roof 90 demolition of mud in roofs , any thickness including plastering and leeping ( weather full thickness removed or part there of ) . 91 supply only integral waterproofing compound 92 applying evenly a tack coat of industrial bitumen 85 / 25 at the rate of1.2 kg per sq.m including cleaning surfaces. 93 preparation of newly plastered surface making surface completely dry and applying a coat of bitumen primer confirming to is :3384 1965 @ 0.30kg / sqm and after drying of primer apply app modified water proofing membrane with non woven polyster reinforcement 3mm thick superior multipolymericweighing not less than 3kg / sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene ( mhhdpe ) film consisting of five layers laid with torching application to the surface over a coat of hot blown bitumen 85 / 25 @1.20 kg / sqm complete and sealing the side as well as end laps ( overlaps should not be less than 10 cm ) complete all as specified and directed by engineer in charge. 94 m&l for 50mmaverage consolidated thickness pcc 1:3:6 type c2with using 20mm graded stone aggregate as in padding on flat roofs etc all as specified and directed. 95 m / l for 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar ( 1:3 ) mixed with 5% of crude oil by weight of cementand pointed flush in cm 1:3 complete all as specified. 96 all as per item 95 above but except tiles. 97 m&l for two coats synthetic enamel paint over new wooden surface over 10 cm width or girth over a coat pink primer complete all as specified 98 m&l for gypsum board 12mm thick in ceiling fixed with screw as per manufacturer instructions 99 s&f 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side 100 s&f mild steel work confirming to fe 290 gde e 165as in wind ties for roof , cutting tops to shape as directed , drilling holes, notching etc complete all as specified 101 s&f in repair pvc swr pipe 110 mm dia single socketed in any length with rubber ring joints laid in trenches etc all as specified 102 ditto all as per item no 101 above but 75 mm dia 103 m&l for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roofs, walls etc fixed with l type or j type or cranked hook bolts. complete all as specified and directed 104 m&l for asbestos cement two piece adjustable plain wing ridge 6mm thick fixed with l type or j type or cranked hook bolts. complete all as specified and directed 105 surface excavation averaging 30 cm deep and getting out in soft / loose soil all as specified and as directed by engr in charge 106 rollling and consolidating formation surafces in cutting with power roller of capacity exc 8 tonne but not exceeding 12 tonne 107 m & l for broken stone or boulder hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled / rammed to a true surfacec omplete all as specified and directed 108 m&l for 100 thick pcc 1:4:8 type d 2 using 40 mm graded aggregate stone as in , filling in sub base and mass concrete completeall as specified and directed 109 m&l for 100 thick pcc 1:2:4 type b 2 using 20 mm graded aggregate stone as in floor and hardstanding completeall as specified and directed 110 removing surplus material, n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point in soft / loose soilcomplete all as specified. 111 m&l for forming contraction joint 65 mm deep x 10mm wide, filled with sealing compound grade a complete all as specified. 112 m & l for forming 12 mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound, grade ‘b’ , complete all as specified and directed byengr in charge 113 m&l for 150mm bore reinforced concrete pipes, class np 2 with one coller per length of pipe complete all as specified and directed. 114 m&l for 15mm thick cement plastering in cement mortar ( 1:4 ) reinforced with wire fabric not exc 4 kg fixed to ventilation duct complete all as specified and directed. 115 s&f in repair of 20mm thick insulating board with fire resistant sheet duly fixed on it and fixing the same on wallscomplete all as specified and directed 116 s&f in repair of rubber bidding 15mm thick on sides of aluminium / wooden door and windows for making air tight complete all as specified and directed. 117 s&f veneered particle boards interior grade 25 mm thick, solid core, general purposes type, with face veneers of typebb, fixed with screws to timber frame work complete as specified. 118 s&f anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long ( 1 no. ) . hinges type b 21 100mm long ( 2 no. ) suitable handle ( 1 no. ) complete all as specified. 119 m & l for 75mm thickfor cement concrete 1:4:8 type d–2 using 40mm graded stone aggregates as in in sub floors, sub bases, floors and pavings etcall as specified and directed byengineer in charge . 120 m&l for sand filling under floors or in foundations including watering and consolidation. 121 s&f in repair 12 mm thick prelaminated particle board, exterior grade, prelaminated on both sides with decorative choice lamination, fixed with screws to timber frame work complete all as specified. 122 s&f 25 mm thick hardwood boarding, supplied & fixed with nails in any situation ( except flooring and skirting ) planed one side with butt joints complete all as specified. 123 m&l for rubber tiles 2.5 mm thick with fabric backing or insert, plain coloured or marbled topping, matt or glossy, laid in floors with approved adhesive including taking down complete all as specified and directed. 124 ditto as item no 123 except rubber tile 125 m&l for three coats of white wash on newly plastered surface including preparation of surface complete all as specified and directed. 126 m&lfor preparationof new plastered surfaces of any description not otherewise describedand applying two coats of cement base painting camouflaging pattern as per designgiven by engineer in charge over a coat of alkali resistant primer on walls including preparation and cleaning the old surface etc complete all as specified and directed. note applicable for item no 126. the design and patternof camouflaging painting with different colour of paints will begiven byengineer in charge the tenderer / contractor shall carryoutwork as per design given byengineer in charge / ge 127 m & l for rcc m 25 for slabs, facia supported on walls, beams, columns and in shelves, the like all as specified and directed by engineer in charge . 128 repair , servicing and overhaulingofrolling shutter gear operated type with chain wheel and hand chain of any size by oiling , greasing to gear box , guide channel , shaft , pully and minor repair to gear box, hood cover, pully etc and replacement of minor parts like spring , pins, lathe etc and including securing guide channel to walls with pcc 1:2:4 type b1 and making good the surfaces with cm ( 1:4 ) and making the rolling shutter functional to the entire satisfaction of the engineer in chargecomplete all as specified. 129 taking down carefully aluminum point wiring on tw batten / in conduit / with conduit ( light / fan / socket or power ) complete and making good the disturbed surfaces of wall / ceiling etc including taking down fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and removing materialfrom site except tube light fittings, fans etc which shall be re usedin work complete all as directed by engineer in charge. 130 material and labour concealed point wiring complete with 1.5 sq.mm ( nominal area ) frls pvcinsulated multi stranded copper conductor in and including heavy duty pvc conduit ( wall thickness 1.6 mm ) including fittings & accessories, with ms concealed terminal boxes with 3mm thick laminated bakelite ( hylum / anchor ) sheet top cover for mounting switch, socket etc for one light / fan / bell point controlled by one switch and regulator with pvc cable copper conductor including 1.5 sqmm solid copper conductor with green frlspvc insulation earth common earth dolly, complete all as specified. make : finolex / havells / plaza / indo asian 131 all as per ser item 130 abovebut for 3 pin socket out let 5 amps on independent board 132 all as per item no 130 above but for 3 pin socket outlet 15 amps with 2.5 sqmm stranded copper conductor pvc unsheathed cable independent including pvc cable copper conductor 1.5 sqmm with green insulator as earth wire with cast iron / pressed steel teminal box all as specified. 133 supply and fixing switch piano flush type 5 amp single pole one way. make : havells / ssk / leader. 134 supply and fixing switch piano flush type 15 amp single pole one way. make : havells / ssk / leader. 135 supply and fixing socket outlet 2 in 1, 3 pin, 5 amps flush type multi purpose. make : havells / ssk / leader. 136 supply and fixing socket outlet 2 in one, 3 pin, 5 and 15amp flush type multi purpose. make : havells / ssk / leader. 137 supply and fixing led tube light fitting 1 x 20 watt, 6000k of make philips / bajaj complete all as specified and directed. 138 supply and fixing ceiling rose surface bakelite 65 x 50mmthree terminals complete all as specified and directed. 139 supply and fixing fan regulator electronic step type and making connection.make : rallison / leader / bajaj 140 supply and fix sheet metal enclosures db’s when mcbs to be used for 240 volts, 8 way spn, double door with 200 amps rated bus bar including earth and neutral link complete all as specified and as directed.make : standard / havells / ship 141 supply and fixmcb spn 40 amps 10ka ‘b’ curve 240 voltsmake indo asian and equal complete all as specified and as directed. 142 supply and fixmcb sp 10 to 30 amps 10ka ‘b’ curve 240 voltsmake indo asian and equalcomplete all as specified and as directed. 143 disconnecting and taking out old unserviceable underground cable of service connection of any size and type from pole to dbs / main switch complete all as specified 144 supply and laying in trences / on pole / wall in protection pipe cable xlpe insulated screened armoured pvc bedded heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 4 core 25 sqmm.make : finolex / havells / plaza / polycab. 145 m & l for replacement of earthing with galvanized iron earth plate electrode 600mm x 600mm, 6mm thick buried directly in ground vertically in a earth pit not less than 2.25mtr below normal ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to gi earth wire 4mm dia by means of gi bolts, nuts, check nuts and washers ( earth plate covered with alternate layers of charcoal dust and common salt 15cm thick ) , gi earth wire protected by gi pipe light grade 15 mm dia upto switch board and connected to main switch board including provision of gi pipe 20 mm dia light grade watering pipe with funnel and wire mesh, all as shown in electrical plate no. 3 of ssr part i, including pcc chamber ( 1:3:6 ) using 20mm graded stone aggregate and ci cover and frame including all necessary excavation and earth work and taking out old earthing complete all as specified and directed. 146 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for laying of cable, foundation of poles , stay and struts etc and getting out in soft / loose soil etc and getting out including trimming of sides all as specified and directed by engineer in charge. 147 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed. 148 removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. 149 material and labour for sand cushioning with a layer of sand 8 cm thick before laying of cable and 15 cm thick after laying of cable in trenches complete all as specified and directed. note: 18cm thickness of sand after punning down shall be measured, recorded & paid. 150 supply and laing old size sub class b bricks alid flat in trenches over the cable with the length of brick perpendicular to lthe direction of cable length adjacent / abutting each other complete all as specified and directed. 151 supply and fixinggi tubing light grade with all fitting laid in trenches , roador wall for cable protection complete all as specified of size 50 mm bore . 152 material and labour for concealed point wiring complete with 1.5 sq.mm ( nominal area ) fr pvcinsulated multi stranded copper conductor in and including heavy duty pvc conduit ( wall thickness 1.6 mm ) including fittings & accessories, with ms module box concealed t with 3mmmodule top cover for mounting switch, socket etc for one light / fan / bell point controlled by one switch and regulator with pvc cable copper conductor including 1.5 sqmm solid copper conductor with green fr pvc insulation earth common earth dolly, complete all as specified.make :finolex / havells / plaza / indo asian 153 ( a ) all as per ser item 152 abovebut for 3 pin socket out let 5 amps on independent board 154 ( b ) all as per ser item 152abovebut for 3 pin socket out let 5 amps on same board 155 all as per srl item no 152 above but for 3 pin socket outlet 15 amps with 2.5 sqmm stranded copper conductor pvc unsheathed cable independent including pvc cable copper conductor 2.5 sqmmwith green insulator as earth wire with cast iron / pressed steel terminal box all as specified. 156 s&fmodular switch6 amp 230 v ac one way, one module complete all as specified 157 s&f modular switch 16 amp 230 v ac one way, with indicator one module complete all as specified 158 s&f modualr socket 6a, 2 / 3 pin two module combined complete all as specified. 159 s&fmodular socket , 6a / 16a, 2 / 3 pin, two module complete all as specified. 160 s&f modularfan regulatorstep type, 120w, 2 module complete all as specified 161 suply and fix white colour plates withframe formodular switchof 01module complete all as specified 162 suply and fix white colour plates withframe formodular switchof 02module complete all asspecified 163 suply and fix white colour plates withframe formodular switchof 03module complete all as specified 164 suply and fix white colour plates withframe formodular switchof 04module complete all as specified 165 suply and fix white colour plates withframe formodular switchof 06module complete all as specified 166 suply and fix white colour plates withframe formodular switchof 08module complete all as specified 167 supply and fixing ceiling rose surface bakelite 65 x 50mmthree terminals complete. make : havells / ssk / leader 168 supply and fixing led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 169 supply and fixing led luminaire 600 mm x 600 mm, 35 / 36 watt, 220 v ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. 170 supply and fixing lamp holder with pvc insulated body fixedplasitc laminated sheet cover shape 3mm thick suitable for batten fitting including 01 no. of led 1 x 15 watt, 230 volts, suitable for 230 volt ac complete all as specified. 171 supply and fixingsingle pole and neutral enclosure with a two pin and earth plug and socket complete with one single mcb 20 amp 172 supply and fixing isolater 63 amps tpn 415 volts.make : standard / ship / havell’s. 173 supply and fixing sheet steel metalenclosure ( db ) triple pole and neutral 4 way 415 , volt with 200 amps rated bus bar make :standard / havells / ship 174 supply, fix, connect and test in replacement , led street light fitting 35 watts ( or above watt ) ip 65 / 66 with pdc aluminium body and toughened glass visor fitted in frame, separate driver compartment provided, secondary optical lens for superior light distribution efficiency >95 lm / w, cct5700k ip65, input voltage from 120 270 v power factor above 0.95 complete fitting including all accessories note : contractor shall provide 1 years written manufactures warranty for the led fixture complete including driver from the certified date of completion. make : polycab cat part no pcgls 01 30 product code pub0502004 and c&s electric cat part no ltess 12 x 2.5 hpled / ls product code indus / 30w / ls ( model indus series ) or equivalent in makes indicated in appendix b of particular specifications complete all as specified and as directednote : contractor shall provide 1 years written manufactures warranty for the led fixture complete including driver from the certified date of completion. 175 supply and fixingceilingfan 1200 mm sweepcompletedwith capacitorcanpyand down rod includingflexibletwin corecopper ( 23 / 0. 0076 ) with provisionof ceiling rose / connectorto fan all as specified . 176 s & f propeller type ac ventilating fans 300 mm sweep pvc body ( exhaust fan ) with louver shutter complete including m & l for providing / cutting the roundhole of required size in wall finishing the same suppply and grouting the ragged bolts in wall fixig the frame on the exhaust side ( outer surface of the wall ) and connecting with and including pvc insulated three core 14 / 0.006 copper cable rubber insulated from ceiling rose to exhaust fan motor and writting mes nowith black synthetic enamel paint 2.0 cm high complete all as specified and directed. 177 supply, laying and testing cable xlpe insulated screened, pvc bedded, galvanised steel strip or wire armoured electric cables ( heay duty 1100 volts grade with stranded aluminium conductor of size 10 sqmm 4 core 178 supply, laying and testing cable xlpe insulated screened, pvc bedded, galvanised steel strip or wire armoured electric cables ( heay duty 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core 179 supply, laying and testing cable xlpe insulated screened, pvc bedded, galvanised steel strip or wire armoured electric cables ( heay duty 1100 volts grade with stranded aluminium conductor of size 70 sqmm 3.5 core 180 material and labour in replacement for earthing complete with copper earth plate electrode 600mm x 600mm x 3.15 mm thick buried directly in ground earth pit not less than 2.25 mtr below normal gl with the top edge of the plate not less then 1.5 mtr below the normal gl connected to 20x3mm copper strip as earth lead by means of bolts, nuts, check nuts and washer of brass and protected by 40 mm gi pipe ( light grade ) and watering pipe 20mm bore gi pipe ( light grade ) including gi wire meshed funnel and chamber pcc ( 1:4:8 ) type d2 using 40mm grade stone aggregate, coping shall be ( 1:3:6 ) type ci using 20mm stone aggregate with rcc 1:2:4 type b1 ( using 20mm graded stone aggregate ) pit cover re inforced with 8mm dia at 80mm c / c both way in lieu of ci pit cover with angle iron frame, including excavation and earth work in any type of soil and removal of surplus soil of earth complete all as shown in electrical plate of ssr part i and as specified including charcoal dust, common salt complete and earth lead connected to earthing test point all as specified and testing of earthing on completion. note 1. the unit rate includes for protection pipe and copper strip 20x3mm from top of earth plate up to 7.5 meter above ground level. 181 supply and fixing round shape 12 watt 220 volts ac recessed type with high efficiency pmma diffuser soft glare free light complete with drivers, holders, led lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complet 182 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complet 183 supply and fix led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size 184 supply and fixing exhaust fan 300 mm sweep 900 rpm, heavy duty, ac single phase 230 / 240 volts, metal body with louver shutters including making circular hole in existing wall to accommodate exhaust fan and necessary civil work and making good the disturbed surface complete all as specified and directed. 185 m&l for sub main wiring with two runs of single core pvc insulated, unsheathed copper condutor, multi stranded cable of size 6.00 sqmm 1100 volts grade drawn pvc concealed conduit of size19 / 20 mm ( isi marked ) including pvc accessories complete incl cutting and chasing and making good etc including one run of 6.00 sqmm single core copper conductormulti stranded pvc insulated, unsheathed cable as earth wire continuity conductor complete all as specified and directed by engineer in charge. note : two run of 6.00 sqmm cable one run of 6.00 sqmm cable as earth continuity conductor and one run of pvc conduit shall be measured & paid as one unit. ) note : two run of 6.00 sqmm cable and one run of 6.00earth wire & 20 mm pvc conduit shall be measured as one unit length 186 all as per above item no 185 butcable size of 4 sqmm...

Water Resources Department - Punjab

29381446 supply,installation, testing, commissioning, training, operation and maintenance of scada based automatic operation of barrage at ropar head works and scada based automatic operation of sirhind canal system supply,installation, testing, commissioning, training, operation and maintenance of scada based automatic operation of barrage at ropar head works and scada based automatic operation of sirhind canal system , part a supply , supply of automated water level transmitter non contact ultrasonic type having 10 m range for measuring level /downstream discharge in canal across the head / cross regulators, including all necessary mast/ cantilever as per technical specification. , supply of shaft encoder based rotary position sensor with digital display type gate position sensors for indication and monitoring of canal gates, including cabling and integration with plc/rtu / datalogger as per technical specifications. , supply, installation, testing and commissioning of side looking acoustic doppler based velocity meter (advm) for direct downstream discharge measurement in head /cross regulators ofcanal system with bed width 20 120m as per the site required,including integration with plc/rtu/datalogger,including retractable mounting frame, cabling,complete as per technical specifications. , supply, installation, testing and commissioning of side looking acoustic doppler based velocity meter (advm) for direct downstream discharge measurement in head /cross regulators ofcanal system with bed width 0 20m as per the site required,including integration with plc/rtu/datalogger,including retractable mounting frame, cabling,complete as per technical specifications. , supply of remote plc/rtu system with software development of plc/rtu, control panel with front door opening cabinet, fitted with power buses, mcbs and modem.suitable power supply to power up plc/rtu panel, including necessary surge protection with 7” or above hmi display and industrial type electrical fitting and cabling with suitable conduits complete for all related field instruments, as per technical specification. , supply ofbullet camera(fixed type) ip digital night vision(i.r) out door weather resistant, 2 mega pixel 2 or4 with sim card slot, 2 mega pixel 2 or 4 array/ 72 led colour camera. 6 or 8 or 12mm (according to site suitability) 3mp auto iris lens in elegant metal die cast housing. outdoor weather resistant ip 66, for monitoring the gates operation at ropar barragecomplete as per technical specifications. , supply of pan tilt zoom (ptz) 36 x optical and 12 x digital zoom; 2 mega pixel ip based (digital) camera, 500 mtrs. night vision (multiple intelligent array system) in ip66 weather resistant outdoor metallic housing. outdoor weather resistant ip 66 including cabling required for barrage & cross regulator monitoring. as per technical specifications. , supply of automatic water level recorder( non contact radar type) for rivers/canals/reservoirs having 35m range with all necessary hardware as per technical specifications. , supply of datalogger 2 analogue channels type with gsm & gprs based telemetry & enclosure including antenna and all necessary equipment for data transmission from remote monitoring stations, as per technical specifications. , supply of solar panel, charger regulator, batteries, lightening arrestor with all connectors, cables and conduit & mounting accessories for power back up to remote plc/rtu/datalogger as per technical specifications. , supply & erection of pre fabricated cabin (size 6x6 and 8 height) with civil foundation m.s. angle 50x50x5, wall ofsteel e.p.s.–steelcompositepanelof.5mmthickgisheetopening door, roof and floor, painting etc. complete as per technical specification. , development of rating curve/stage discharge curve as per is 15119(part1&2) and is 15847 at a river site/location(continuous activity for 4 years and rating curve shall be revised/updated annually using departmental adcp (operation and maintenance cost of adcp to be borne by agency) , supply of main plc controller system with firm ware based hot redundancy which shall include software development of plc, control panel with front door opening cabinet, fitted with power buses, mcbs & modem. all the electrical fittings will be industrial type. including suitable switch mode power supply (smps), 12” display & interconnection with related remote plc/rtu’s, complete as per technical specification. , supply of customized irrigation monitoring software which shall include scada software for real time monitoring & controlling of canal operations, water scheduling, real time data logging for complete canal system with life time licensed version. as per technical specifications. , supply of master gradeserver which includes server with work station server rack and industrial grade monitor with usb, rs232/rs485, ethernet ports, os windows 8 or higher compatible to scada system complete forcanal system, as per technical specifications. , network video recorder (nvr) 32 channel 1080 p full hd, real time recording and reviewing in compression format. with hdd. along with dedicated server with sufficient hard drive to have memory of at least 30 days as per technical specifications. , supply of industrial grade computer node as workstation along with monitor, and necessary accessories,42 inch led display ,4g/3g dongles/broadband, installed with client scada software including 1 kva ups for power back up and a4 size colour printer as per technical specifications at division monitoring station with necessary accessories , supply of laptops & 4g/3g internet dongles along with licensed version of client scada software for remote viewing & monitoring of barrage automation as per technical specifications , supply of it hardware which includes required static ip, router, switch, firewall system and a3 colour printer as per technical specifications. , supply of 110” smart led display system for monitoring of canal system at canal scada control room, as per technical specifications. , supply of online 3 kva ups with battery system for power back up of canal scada control room equipment’s as per the technical specifications. , supply of diesel generator set 10 kva with 04 earth pits for earthing at canal scada control room. , part b installation , installation, testing and commissioning of automated water level transmitter non contact ultrasonic type having 10 m range for measurement of upstream level/downstream discharge in canal across head / cross regulators. including all necessary mast/ cantilever associated civil works cabling, conduits and electrical fitting complete as per technical specification. , installation, testing and commissioning of shaft encoder based rotary position sensor with digital display type gate position sensors for indication and monitoring of canal gates, including cabling and integration with plc/rtu/datalogger as per technical specifications. , installation, testing and commissioning of remote plc/rtu system with software development of plc/rtu, control panel with front door opening cabinet, fitted with power buses, mcbs and modem.suitable power supply to power up plc/rtu panel, including necessary surge protection with 7” or above hmi display and industrial type electrical fitting and cabling with suitable conduits complete for all related field instruments, as per technical specification. , installation, testing and commissioning & integration with nvr located at barrage control room of bullet camera(fixed type) ip digital night vision(i.r) out door weather resistant, 2 mega pixel 2 or4 with sim card slot, 2 mega pixel 2 or 4 array/ 72 led colour camera. 6 or 8 or 12mm (according to site suitability) 3mp auto iris lens in elegant metal die cast housing. outdoor weather resistant ip 66, for monitoring the gates operation at ropar barrage completeas per technical specifications. , installation, testing & commissioning & integration with nvr located at barrage control room of pan tilt zoom camera, 36 x optical and 12 x digital zoom; 2 mega pixel ip (digital) camera, 500 mtrs. night vision (multiple intelligent array system) in ip66 weather resistant outdoor metallic housing. outdoor weather resistant ip 66 including cabling & conducting required for barrage monitoring , installation, testing & commissioning of water level transmitter non contact radar type having 35m range for measuring upstream level & downstream discharge of barrage. including all necessary cabling, electrical fitting & mast complete, as per technical specifications. , installation, testing and commissioning of datalogger2 analogue channels with gsm and gprs based telemetry & enclosure including antenna and all necessary equipment for data transmission from remote monitoring stations, as per technical specifications. , installation of chain link fencing of (5m*5m)*2m along with lockable gates for external protection of sensors and dcp at rtdas station as per technical specification , installation, testing and commissioning of solar panel, charger regulator, batteries, lightening arrestor with all connectors, cables and conduit & mounting accessories for power back up to remote plc/rtu/datalogger as per technical specifications. , installation, testing & commissioning of main plc controller system with firm ware based hot redundancy which shall include software development of plc, control panel with front door opening cabinet, fitted with power buses, mcbs & modem.including suitable switch mode power supply (smps) ,12” display & cabling with industrial grade type electrical fittings for related remote plc/rtu’s, as per technical specification. , installaton of customized irrigation monitoring software which shall include scada software for real time monitoring & controlling of canal operations, water scheduling, real time data logging for complete canal system with life time licensed version, as per technical specifications. , installation, testing and commissioning of master server which includes server with work station server rack and industrial grade monitor with usb, rs232/rs485, ethernet ports, os windows 8 or higher compatible to scada system complete for canal system, as per technical specifications. , installation, testing & commissioning of network video recorder (nvr) 32 channel 1080 p full hd, real time recording and reviewing in compression format. with hdd along with dedicated server with sufficient hard drive to have memory of at least 30 days as per technical specifications. , installation testing & commissioning of industrial grade computer node as workstation along with monitor, and necessary accessories,42 inch led display ,4g/3g dongles/broadband, installed with client scada software including 1 kva ups for power back up and a4 size colour printer as per technical specifications at division monitoring station with necessary accessories , installation, testing and commissioning of online 3 kva ups with battery system for power back up of scada control room equipment’s as per the technical specifications. , installation, testing and commissioning of it hardware which includes required static ip, router, switch, firewall system and a3 colour printer at scada control room as per technical specifications. , installation, testing and commissioning of diesel generator set 10 kva with 04 earth pits for earthing atcanal scada control room. , installation, testing and commissioning of 110” smart led display system for monitoring of canal system at scada control room, as per technical specifications. , charges of high speed synchronous internet connection (min. 8 mbps upload and download speed) and static ip forcanal system for five years. , charges for high speed 4g/3g internet dongle for laptop with client scada software for remote viewing & monitoring of system and 7 division monitoring stations for five years , five years operation & maintenance and comprehensive warranty for scada based canal monitoring & controlling system with telemetry along with accessories, installed at designated locations within canal system after final acceptance of the scada systems. this includes replaceme+b20nt of material & consumable as & when required at bidders’ cost. the cost of communication for gsm & gprs (sim & internet charges) telemetry for data transmission shall be borne by bidder. minimum one service engineer shall be placed at canal scada control room for operation of canal monitoring & controlling system with telemetry for entire warranty period of 5 years....

Central Organisation For Modernisation Of Workshops - Punjab

28382628 supply of cantilever type with single welding head, twin station h/i beam welding machine.cantilever type with single welding head, twin station h/i beam welding machine.,cantilever type with single welding head, twin station h/i beam weldingmachine as per specification no. cofmow/ir/cantilever type with single head, twin station h/i beamwelding machine/2021 , all concomitant accessories as per clause 4.2 section iv of bid documentpart ii.sse/bws/n.r./jrc punjab 1.00 set , foundation, installation, commissioning and proving test as per clause 11 and 12 section v of biddocument part iipage 1 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender document , comprehensive annual maintenance contract for five years after expiryof warranty of two years as per clause 17,section v of bid document part ii.warranty period: 2 years, amc period: 5 years, rate of discounting: 10 %sse/bws/n.r./jrc punjab 1.00 numbersat (location)(jalandhar cantt.)5 es3 (bm1) essential non stock yes consignee inr services (y)preventive maintenance charges during 1st and 2nd years of warranty period.sse/bws/n.r./jrc punjab 1.00 numbersat (location)(jalandhar cantt.)6 osp1 optional non stock no rites inr (bm1) spares (y)optional accessories with break up of individual items as per clause 4.3 ofsection iv of bid document part ii.sse/bws/n.r./jrc punjab 1.00 numbersconsignee(jalandhar cantt.)3. t and cf.o.rdescriptiondestinationdelivery perioddescription delivery /completion rate of supplyfor all items completion : within 270 days as per clause 7of section iv ofbid documentpart iifor all items completion : within 270 days as per clause 7of section iv ofbid documentpart iipayment termss.no descriptionpayment terms1 as per clause 1802 section ii [general conditions of contract] of bid documentpart istatutory variation clauses.no descriptionpage 2 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:001 statutory variation in taxes and duties, or fresh imposition of taxes and duties by state/ central governments inrespect of the items stipulated in the contract (and not the raw materials thereof), within the original deliveryperiod stipulated in the contract, or last unconditionally extended delivery period shall be to railways account.only such variation shall be admissible which takes place after the submission of bid. no claim on account ofstatutory variation in respect of existing tax/duty will be accepted unless the tenderer has clearly indicated in hisoffer the rate of tax/duty considered in his quoted rate. no claim on account of statutory variation shall beadmissible on account of misclassification by the supplier/ contractor. this clause shall read with clause 1211(vi) of section i and clause 1200 and 1300 section ii of bid document part ioption clauses.no description1 as per clause 1602 section ii of bid document part istandard governing conditionss.no description1 as per bid document part i attached with the tender4. eligibility conditionsspecial eligibility criterias.no. description confirmation remarks documentsrequired allowed uploading1 as per special conditions of tender attached with the tender. yes yes allowed(mandatory)standard eligibility criterias.no. description confirmation remarks documentsrequired allowed uploading1 as per clause 0500 of instructions to tenderers, bid yes yes alloweddocument part i. (optional)5. compliance conditionscheck lists.no. description confirmation remarks documentsrequired allowed uploading1 have you submitted banker details viz. name of bank and no no not allowedcomplete address with pin code, bank a/c number, typeof a/c, branch code no., benificiary name andaddress,ifsc code, rtgs code etc. alongwith gstregistration certificate, it is essential to submit thebanks details for releasing payments.2 have you quoted warranty obligations as per para 3409 of instructions to no no not allowedtenderers bid document part i ?3 have you quoted delivery period correctly and precisely ? no no not allowed4 have you quoted for any other items considered essential by you for the no no not allowedoperation of the machine to meet the purpose and capability specified intechnical specification.[under essential spares]5 have you submitted annexure a of section vi of technical specifications no no not allowedbid document part ii , duly filled in6 have you submitted other supporting documents to establish your eligibility no no not allowed? it may consists of the followings :6.1 details related to compliance of reference clause mentioned in special no no not allowedconditions of tender.page 3 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:006.2 statement of equipment and quality control annexure 2 bid documents no no not allowedpart i6.3 bankers report,financial statements etc. para 0501 (b) of instructions to no no not allowedtenderers bid documents part i6.4 commercial details and performance statement annexure i bid no no not alloweddocument part i7 have you quoted price of basic machine, concomitant accessories, no no not allowedessential spares, essential services, amc and other items as per therequirement. it is mandatory to submit offers against all these itemsotherwise the bid shall not be considered in ranking8 have you quoted for optional accessories,spares,amc etc, if applicable no no not allowedand as per the requirement of bid document part ii ?9 have you uploaded self certification or auditors / accountants certificate in no no not allowedsupport of your claim for preference to make in india, if any as per clause0114 section i of bid document part i.commercial compliances.no. description confirmation remarks documentsrequired allowed uploading1 please enter the percentage of local content in the material being offered. no yes allowedplease enter 0 for fully imported items, and 100 for fully indigenous items. (optional)the definition and calculation of local content shall be in accordance withthe make in india policy as incorporated in the tender conditions.general instructionss.no. description confirmation remarks documentsrequired allowed uploading1 tender document consists of bid document part i, bid no no not alloweddocument part ii, special conditions of tender, nit andconditions mentioned in this document. tenderers toensure compliance of conditions mentioned in thesedocuments.special conditionss.no. description confirmation remarks documentsrequired allowed uploading1 in terms of clause 1102, section i, bid document part i, insurance charges no no not allowedfor indigenous components, should be quoted in other charges columnagainst the particular items. no separate line item has been provided forinsurance charges.technical compliancess.no. description confirmation remarks documentsrequired allowed uploading1 bidders must submit their technical bids as per annexure a in section vi yes yes allowedbid document part ii. tenderers are required to submit complete details (mandatory)including values, write up, drawings, sketch, brochure etc. as perrequirement specified in respective clauses mentioned therein. in case ofincomplete / sketchy information, the technical offer being incomplete isliable to be rejected. tenderers should clearly indicate compliance.undertakingss.no. description confirmation remarks documentsrequired allowed uploadingpage 4 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:001 i/we agree to supply the tendered stores at the rates quoted by me/us in no no not allowedaccordance with the conditions mentioned in bid document part i, biddocument part ii, special conditions of tender, nit and conditionsmentioned in this document.2 i/we also confirm that rates and other financial terms quoted in relevant no no not allowedcolumns of financial bid will only be applicable for acceptance. such termsquoted anywhere else shall not be considered for inter se evaluation.s.no. description confirmation remarks documentsrequired allowed uploading1 attention is invited to no. 19 vide which public procurement no yes not allowedorder ( make in india) dated 04.06.2020 and 16.09.2020has been includedas part of tender document. bidders are further requested to take specialnote of following clause of public procurement order (make in india) dated16.09.2020. entities of countries which have been identified by the nodalministry / department as not allowing indian companies to participate intheir government procurement for any item related to that nodal ministryshall not be allowed to participate in government procurement in india forall items related to that nodal ministry / department, except for the list ofitems published by the ministry / department permitting their participation.the term entity of a country shall have the same meaning as under thefdi policy of dpiit as amended from time to time.s.no. description confirmation remarks documentsrequired allowed uploading1 bidders to attach separate price break up of concomitant accessories, no yes allowedessential spares, optional spares/accessories and consumables etc. in (mandatory)pdf format alongwith their bid.6. documents attached with tenders.no. document name document description1 pdf.splconditionsforh ibeamweldingmc15.6.21bystore.pdf special conditions of tender2 biddocumentpart ioct17uptocorr.no.20.pdf bid document part icofmownewformatspecforcantilevertypehbeamweldingmachine 3 bid document part iijrcason8_5.pdf7. responsivenesss.no. description1 validity of offer: no deviation from the offer validity period stipulated in the tender is permitted.this tender complies with public procurement policy (make in india) order 2017, dated 15/06/2017, issued bydepartment of industrial promotion and policy, ministry of commerce, circulated vide railway board letter no.2015/rs(g)/779/5 dated 03/08/2017 and 27/12/2017 and amendments/ revisions thereof.as a tender inviting authority, the undersigned has ensured that the issue of this tender does not violate provisions ofgfr regarding procurement through gem.digitally signed by sse/prtg. ( vineet kumar )page 5 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:00 , preventive maintenance charges during 1st and 2nd years of warranty period.sse/bws/n.r./jrc punjab 1.00 numbersat (location)(jalandhar cantt.)6 osp1 optional non stock no rites inr (bm1) spares (y)optional accessories with break up of individual items as per clause 4.3 ofsection iv of bid document part ii.sse/bws/n.r./jrc punjab 1.00 numbersconsignee(jalandhar cantt.)3. t and cf.o.rdescriptiondestinationdelivery perioddescription delivery /completion rate of supplyfor all items completion : within 270 days as per clause 7of section iv ofbid documentpart iifor all items completion : within 270 days as per clause 7of section iv ofbid documentpart iipayment termss.no descriptionpayment terms1 as per clause 1802 section ii [general conditions of contract] of bid documentpart istatutory variation clauses.no descriptionpage 2 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:001 statutory variation in taxes and duties, or fresh imposition of taxes and duties by state/ central governments inrespect of the items stipulated in the contract (and not the raw materials thereof), within the original deliveryperiod stipulated in the contract, or last unconditionally extended delivery period shall be to railways account.only such variation shall be admissible which takes place after the submission of bid. no claim on account ofstatutory variation in respect of existing tax/duty will be accepted unless the tenderer has clearly indicated in hisoffer the rate of tax/duty considered in his quoted rate. no claim on account of statutory variation shall beadmissible on account of misclassification by the supplier/ contractor. this clause shall read with clause 1211(vi) of section i and clause 1200 and 1300 section ii of bid document part ioption clauses.no description1 as per clause 1602 section ii of bid document part istandard governing conditionss.no description1 as per bid document part i attached with the tender4. eligibility conditionsspecial eligibility criterias.no. description confirmation remarks documentsrequired allowed uploading1 as per special conditions of tender attached with the tender. yes yes allowed(mandatory)standard eligibility criterias.no. description confirmation remarks documentsrequired allowed uploading1 as per clause 0500 of instructions to tenderers, bid yes yes alloweddocument part i. (optional)5. compliance conditionscheck lists.no. description confirmation remarks documentsrequired allowed uploading1 have you submitted banker details viz. name of bank and no no not allowedcomplete address with pin code, bank a/c number, typeof a/c, branch code no., benificiary name andaddress,ifsc code, rtgs code etc. alongwith gstregistration certificate, it is essential to submit thebanks details for releasing payments.2 have you quoted warranty obligations as per para 3409 of instructions to no no not allowedtenderers bid document part i ?3 have you quoted delivery period correctly and precisely ? no no not allowed4 have you quoted for any other items considered essential by you for the no no not allowedoperation of the machine to meet the purpose and capability specified intechnical specification.[under essential spares]5 have you submitted annexure a of section vi of technical specifications no no not allowedbid document part ii , duly filled in6 have you submitted other supporting documents to establish your eligibility no no not allowed? it may consists of the followings :6.1 details related to compliance of reference clause mentioned in special no no not allowedconditions of tender.page 3 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:006.2 statement of equipment and quality control annexure 2 bid documents no no not allowedpart i6.3 bankers report,financial statements etc. para 0501 (b) of instructions to no no not allowedtenderers bid documents part i6.4 commercial details and performance statement annexure i bid no no not alloweddocument part i7 have you quoted price of basic machine, concomitant accessories, no no not allowedessential spares, essential services, amc and other items as per therequirement. it is mandatory to submit offers against all these itemsotherwise the bid shall not be considered in ranking8 have you quoted for optional accessories,spares,amc etc, if applicable no no not allowedand as per the requirement of bid document part ii ?9 have you uploaded self certification or auditors / accountants certificate in no no not allowedsupport of your claim for preference to make in india, if any as per clause0114 section i of bid document part i.commercial compliances.no. description confirmation remarks documentsrequired allowed uploading1 please enter the percentage of local content in the material being offered. no yes allowedplease enter 0 for fully imported items, and 100 for fully indigenous items. (optional)the definition and calculation of local content shall be in accordance withthe make in india policy as incorporated in the tender conditions.general instructionss.no. description confirmation remarks documentsrequired allowed uploading1 tender document consists of bid document part i, bid no no not alloweddocument part ii, special conditions of tender, nit andconditions mentioned in this document. tenderers toensure compliance of conditions mentioned in thesedocuments.special conditionss.no. description confirmation remarks documentsrequired allowed uploading1 in terms of clause 1102, section i, bid document part i, insurance charges no no not allowedfor indigenous components, should be quoted in other charges columnagainst the particular items. no separate line item has been provided forinsurance charges.technical compliancess.no. description confirmation remarks documentsrequired allowed uploading1 bidders must submit their technical bids as per annexure a in section vi yes yes allowedbid document part ii. tenderers are required to submit complete details (mandatory)including values, write up, drawings, sketch, brochure etc. as perrequirement specified in respective clauses mentioned therein. in case ofincomplete / sketchy information, the technical offer being incomplete isliable to be rejected. tenderers should clearly indicate compliance.undertakingss.no. description confirmation remarks documentsrequired allowed uploadingpage 4 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:001 i/we agree to supply the tendered stores at the rates quoted by me/us in no no not allowedaccordance with the conditions mentioned in bid document part i, biddocument part ii, special conditions of tender, nit and conditionsmentioned in this document.2 i/we also confirm that rates and other financial terms quoted in relevant no no not allowedcolumns of financial bid will only be applicable for acceptance. such termsquoted anywhere else shall not be considered for inter se evaluation.s.no. description confirmation remarks documentsrequired allowed uploading1 attention is invited to no. 19 vide which public procurement no yes not allowedorder ( make in india) dated 04.06.2020 and 16.09.2020has been includedas part of tender document. bidders are further requested to take specialnote of following clause of public procurement order (make in india) dated16.09.2020. entities of countries which have been identified by the nodalministry / department as not allowing indian companies to participate intheir government procurement for any item related to that nodal ministryshall not be allowed to participate in government procurement in india forall items related to that nodal ministry / department, except for the list ofitems published by the ministry / department permitting their participation.the term entity of a country shall have the same meaning as under thefdi policy of dpiit as amended from time to time.s.no. description confirmation remarks documentsrequired allowed uploading1 bidders to attach separate price break up of concomitant accessories, no yes allowedessential spares, optional spares/accessories and consumables etc. in (mandatory)pdf format alongwith their bid.6. documents attached with tenders.no. document name document description1 pdf.splconditionsforh ibeamweldingmc15.6.21bystore.pdf special conditions of tender2 biddocumentpart ioct17uptocorr.no.20.pdf bid document part icofmownewformatspecforcantilevertypehbeamweldingmachine 3 bid document part iijrcason8_5.pdf7. responsivenesss.no. description1 validity of offer: no deviation from the offer validity period stipulated in the tender is permitted.this tender complies with public procurement policy (make in india) order 2017, dated 15/06/2017, issued bydepartment of industrial promotion and policy, ministry of commerce, circulated vide railway board letter no.2015/rs(g)/779/5 dated 03/08/2017 and 27/12/2017 and amendments/ revisions thereof.as a tender inviting authority, the undersigned has ensured that the issue of this tender does not violate provisions ofgfr regarding procurement through gem.digitally signed by sse/prtg. ( vineet kumar )page 5 of 6 run date/time: 02/07/2021 14:49:08stores/cofmowtender documenttender no op 713030 closing date/time 02/08/2021 15:00 , optional accessories with break up of individual items as per clause 4.3 ofsection iv of bid document part ii....

Northern Railway - Punjab

27981571 supply of replacement of corroded cantilever assemblies, anti creep and tail feeders in the polluted zone of sahnewal ( snl ) amritsar ( asr ) section of firozpur division to improve the reliability of ohereplacement of corroded cantilever assemblies, anti creep and tail feeders in the polluted zone of sahnewal ( snl ) amritsar ( asr ) section of firozpur division to improve the reliability of ohe, ...

Military Engineer Services - Punjab

27089714 provision of bazaar supply items at af stn bhisiana 1 coarsed stone aggregate 12.5mm grade locally best available from approved quaries. 2 coarsed stone aggregate 20mm grade locally best available from approved quaries. 3 fine aggregate ( sand ) locally best available from apoved quories. 4 portland cement grade 43 50 kgs bag. make jk / ultratech / acc / shree cement / ambuja or equilvent. 5 white portland cement in in polyethelyne bags or other packing. make jk birla white or equilvent. 6 sub class bricks of standard size locally best available from approved furnaces. 7 200 mm ordinary rat tail rod pattern door springs with roller and roller plate. 8 mortice lock 2 levers vertical type size 100 mm. make: link / godrej or equivalent. 9 cup board locks brass with 2 levers make : link / godrej or equivalent. 10 brass polished cuboard knobs fixed with nut, screw and washer. make as per sample kept in ge office. 11 floor door stoper aluminium alloy body with hard drawn steel spring double leg. make as per sample kept in ge office. 12 stainless steel wiremesh, 0.56 mm nominal dia of wire and average width if apreture 1.4mm. make agtha / elephant or equilvent nnote : wiremesh roll should be 1.2 mtr wide to avoid wastage. 13 galvanised iron ms wire cloth, 0.63 mm nominal dia of wire and average width of apreture 1.4 mm. make agtha / elephant or equilvent. nnote wiremesh roll should be 1.2 mtr wide to avoid wastage. 14 0.56 mm plain aluminium sheet. 15 plywood grade bwp type bb 6 mm thick, commercial facing size 8x4 make centuary / kitply / greenply / mysorechip board. 16 plywood grade bwp type bb 4 mm thick, commercial facing 8x4. nmake centuary / kitply / greenply / mysorechip board 17 aluminium standard door bottom seal with nylon brush at lower side to fit at the bottom of door shutter upto 1.1m length. make as per sample kept in ge office. 18 flexible rubber 5 mm th 50 mm wide for door bottom seal. make as per sample kept in ge office. 19 neoprene beading for aluminium windows / doors glass fixing. make as per sample kept in ge office. 20 aluminium butt hinges 100 size. make: crown, classic, argent , isi marked. 21 aluminium butt hinges 75 size. make: crown, classic, argent , isi marked. 22 aluminium sliding door bolt 300 mm along with locking plate. make : crown, classic, argent , isi marked. 23 aluminium sliding door bolt 250 mm along with locking plate. make: crown, classic, argent , isi marked. 24 mild steel wire nails with head for wiremesh ( black ) size n.exc 20mm. make as per sample kept in ge office. 25 mild steel wire nails with head for wiremesh door bidding, fixing of plywood and size not exc 25mm ( 17 nos ) . make as per sample kept in ge office. 26 mild steel wire nails with head for door repairs size not exc 50mm ( 12 nos ) . make as per sample kept in ge office. 27 mild steel wire nails with head for size not exc 25mm ( 14 nos ) . make as per sample kept in ge office. 28 mild steel wire nails with head for size not exc 50mm ( 10 nos ) . make as per sample kept in ge office. 29 mild steel wire nails with head for size not exc 100mm ( 8 nos ) . make as per sample kept in ge office. 30 mild steel wire nails with head for size not exc 100mm ( 10 nos ) . make as per sample kept in ge office. 31 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 75x10. make as per sample kept in ge office. 32 mild steel machine screws, bright finished, with slotted countersunk head, full length threaded n.exc 50mm ( black ) . make as per sample kept in ge office. 33 mild steel full length threaded screws for iron window size n.exc 15mm. make as per sample kept in ge office. 34 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 30x7. make as per sample kept in ge offce. 35 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 35x8. make as per sample kept in ge office. 36 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 19x10. make as per sample kept in ge office. 37 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 19x8. make as per sample kept in ge office. 38 25mm wide pvc lipping for cupboard and inbuild furnitures. 39 brass spimndle for concealed stop cocks for 15mm dia ( half turn ) as per sample kept in ge office. 40 brass spindle for piller cock for 15mm dia ( half turn ) as per sample kept in ge office. 41 brass spindle for stop cocks for 15mm dia ( half turn ) as per sample kept in ge office. 42 brass spindle for bib cocks for 15mm dia ( half turn ) as per sample kept in ge office. 43 15 mm dia long body cp bib tap make : hindware, cera, parryware, gem, prayag. 44 15 mm two way cp angle cock. make: hindware, cera, parryware or equivalent. 45 flexible telephonic pipe for health faucets and hand shovers length 1.2 mtr. make: hindware, cera, parryware, gem, prayag. 46 cp shower rose ( cicular or square shape 125 mm dia ) with pivot and arm. make : hindware, cera, parryware, gem, prayag. 47 syphon set ( internal kit ) for flush tanks. make : prayag , hindustan, parryware. 48 ptmt grating dooms of size 150 mm square and provision of hinge system to open and closing of cocroch trap. make : prayag, gem or equivalent. 49 pvc water tank cover for 500 ltr. make : sintex / polycone / renutuff / cera. 50 pvc water tank cover for 1000 ltr tank. make : sintex / polycone / renutuff / cera. 51 gi socket 20mm isi marked. 52 gi socket 15mm isi marked. 53 gi elbow 15 mm isi marked. 54 gi elbow 20 mm isi marked. 55 gi nipple 15mm x 100 mm isi marked. 56 gi nipple 15mm x 125 mm isi marked. 57 gi nipple 15mm x 150 mm isi marked. 58 gi nipple 15mm x 50mm isi marked. 59 gi nipple 15mm x 75mm isi marked. 60 gi nipple 20mm x 100 mm isi marked. 61 gi nipple 20mm x 125 mm isi marked. 62 gi nipple 20mm x 150 mm isi marked. 63 gi nipple 20mm x 50 mm isi marked. 64 gi nipple 20mm x 75 mm isi marked. 65 gi plug 15mm. 66 gi plug 20mm. 67 gi reducer elbow 20 mm x 15mm isi marked. 68 gi reducer elbow 25mm x 20mm isi marked. 69 gi reducer socket 20mm x 15 mm isi marked. 70 gi reducer socket 25mm x 15mm isi marked. 71 gi reducer socket 25mm x 20mm isi marked. 72 gi reducer tee 20 mm x 15mm isi marked. 73 gi tank nipple 15 mm isi marked. 74 gi tank nipple 20 mm isi marked. 75 gi tee 15 mm isi marked. 76 gi tee 20 mm isi marked. 77 gi union 15mm isi marked. 78 gi union 20mm isi marked. 79 washer for syphone sets internal / external dia of washer as required. make as per sample 80 stainless steel sliding telescopic channels having length 450 mm for kitchen cupboard drawers and shelves. make: godrej, hettich or equivalent. 81 stainless steel sliding telescopic channels having length 600 mm for kitchen cupboard drawers and shelves. make: godrej, hettich or equivalent. 82 stainless steel welding rod for s s metal welding ( dia of rod 3.15 and length 350mm ) . 83 welding rod ( electrodes ) for metal arc welding ( dia of rod 3.15 mm and lenth 350mm ) . 84 chromium plated brass 32mm bottle trap with 300 mm and 190 mm long wall connection flange pipe. make hindware, parryware, cera or gem, prayag. 85 chromium plated brass hand shover ( health faucet ) with 8 mm dia, 1.2 mtr long telephonic flexible tube & wall hook. make : cera, hindware, prayag, gem or parryware. 86 chromium plated brass 15 mm dia angular stop cock with wall flange. make : cera, hindware, prayag, gem or parryware. 87 wall mixer with provision for over head shover with 115 mm long bend pipe on upper side, connecting legs and wall flanges. make : cera, hindware, prayag, gem or parryware. 88 15mm dia chromium plated bib taps. make : cera, gem, hindware, parryware or prayag. 89 15 mm dia ptmt bib taps. make : prayag, polytuf. 90 15 mm dia chromium plated pillar tap. make : cera, gem, hindware, parryware or equivalent. 91 bevelled edge frame less looking mirror of rectangular shape of size 600 x 450 mm with wall mounting arrange ments. make: prayag, modi, tripurti. 92 110 mm dia pvc swr bends make as per sample kept in ge office. 93 75mm dia pvc swr bends make as per sample kept in ge office. 94 100 mm oval / round shape cast iron pipe covers for cast iron vertical stacks make as per sample kept in ge office. 95 75 mm oval / round shape cast iron pipe covers for cast iron vertical stacks make as per sample kept in ge office. 96 ewc seat covers with mild steel hinging device. make: cera, prayag, hindustan, hindware. 97 stainless steel curtain rod 25mm dia. make : as per sample kept in ge office. 98 statinless steel bracket for curtain rod 25mm dia wall to wall ( end bracket ) , l type. make : as per sample kept in ge office. 99 statinless steel desginer end ( laatu ) for curtain rod 25mm dia. make : as per sample kept in ge office. 100 25mm dia ms powder coated as in approved colour curtain rod for doors and windows. make : as per sample kept in ge office. 101 ms powder coated as in approved colour bracket for curtain rod of 25mm dia. make : as per sample kept in ge office. 102 ms powder coated as in approved colour designer end dooms for curtain rod of 25mm dia. make : as per sample kept in ge office. 103 m seal 100gm pkts. make : as per sample kept in ge office. 104 continous piano himges, 180 degree with holes, stainless steel wide 32mm. make : as per sample kept in ge office. 105 nickel chrome handle for cupboard of size 100mm. make : as per sample kept in ge office. 106 oil putty for fitting of glass panes. make : as per sample kept in ge office. 107 urinal waste pipe with nuts 750mm long. make : as per sample kept in ge office. 108 pvc waste pipe for washbasin, kitchen sink etc. of length 750mm & dia 32mm. make : as per sample kept in ge office. 109 flush down pipe 90 degree for low level of flushing cistern. make : as per sample kept in ge office. 110 gi tube medium grade of size 15mm isi marked. 111 gi tube medium grade of size 20mm isi marked. 112 15mm ball valves, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball. make : as per sample kept in ge office. 113 20mm ball valves, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball. make : as per sample kept in ge office. 114 wash basin bracket of cast iron, length upto wash basin length. make as per sample kept in ge office. 115 gi clamp for tube, of size 15mm to 55mm & width 0.5 to 1 inch with corrosive resistant make as per sample kept in ge office. 116 threads for pipe sealent. make as per sample kept in ge office. 117 pvc corner shelf ( set of 3 ) . make: as per sample kept in ge office. 118 prespex sheet 3mm thick with transparent with clear visibility. make as per sample kept in ge office. 119 pvc connection with ptmt nut of size 450mm. make : as per sample kept in ge office. 120 pvc connection with ptmt nut of size 600mm. make: as per sample kept in ge office. 121 roval plug make as per sample kept in ge office. 122 stainless steel chorme towel ring. make as per sample. 123 stainless steel wall ounted soap dish. make as per sample. 124 frosted glass 4mm thick. make : modiguard, saint gobain. 125 sink coupling 2 size make as per sample kept in ge office. 126 sink coupling 4 size make as per sample kept in ge office. 127 waste coupling 32mm size make as per sample kept in ge office 128 plain glass sheet 3mm thick. make : modiguard, saint gobain. 129 ms sliding door bolt 250mm along locking plate isi marked. 130 ms sliding door bolt 300mmalong locking plate isi marked. 131 ms handle 150mm oval shape isi marked. 132 aluminium handle 150mm fabricated type. 133 ms tower bolt 100mm isi marked. 134 ms tower bolt 150mm isi marked. 135 aluminium tower bolt 100mm isi marked. 136 aluminium tower bolt 150mm isi marked. 137 aluminium hasp and staple 150mm isi marked. 138 pvc cistern 10 ltr capacity with ball valve, superflow / flush kit complete set. make : prayag, hindware , cera. 139 chromium plated 15 mm dia wash hand basin mixer. make : cera, jainko, or equivalent 140 chromium plated 15 mm dia swan neck sink mixer. make: cera, jainko. 141 mouchi nails 1 / 2 make as per sample. 142 5.50mm thick tinted glass. make modiguard, saint gobain. 143 alluminium die cast body door closer hydraulically regulated, designation no. 2, universal type, for door weight between 36 to 60 kg. make : everest, universal, godrej. 144 lime ( calcium oxide ) 20 kg bag. make suryacem. 145 water based oil bound distemper in approved colour. make: asian, berger or equivalent 146 synthetic enamel paint for wooden and steel surfaces. make: berger, asian or equivalent. 147 thinner for enamel paints ( min flash point 40 degree ) . 148 paint brush 4 inch wide flat with wooden handle as per sample. 149 paint brush 3 inch wide flat with wooden handle as per sample. 150 paint brush 2 inch wide flat with wooden handle as per sample. 151 premixed bitumin ( bituminus cold mix ) 20 kg bag. make boral. 152 chromium plated 600 mm length towel rod. make : cera, bharath, hindware. 153 fevicol sr adhessive. 154 vitreous china wash basin, white, flat back, size 580x450mm including brackets. make : cera, hindware, hindustan. 155 vitreous china wash down water closet pan ( pedestal pattern ) . make: cera, hindware, hindustan. 156 vitreous china squatting pan, ‘orissa’ pattern, size 580 x 440 mm white, with integral foot rests. make : cera, hindware, hindustan. 157 stainless steel sink, 1.00mm thick for kitchen, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 20mm with bowl size 410mm x 330mm x 160mm make : blue star, nirali. 158 stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm. make : blue star, nirali or equivalent. 159 flench / cap for cp bib tap, stop cock etc. make as per sample kept in ge office. 160 4 pole ( mcb fp ) of 63 / 80 amp 240 / 415 volts 10 ka finger proof terminal, bi connect termination, label holder, 50 mm² terminal capacity, insulated sliding shutter, large two position dolly. 161 4 pole ( mcb fp ) of 100 amp 240 / 415 volts 10 ka finger proof terminal, bi connect termination, label holder, 50 mm² terminal capacity, insulated sliding shutter, large two position dolly. 162 4 pole ( mcb fp ) of 125 amp 240 / 415 volts 10 ka finger proof terminal, bi connect termination, label holder, 50 mm² terminal capacity, insulated sliding shutter, large two position dolly. 163 2 pole ( mcb dp ) of 63 amp 240 volts 10 ka c curve finger proof terminal, bi connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly. 164 1 pole ( mcb sp ) of 25 amp 240 volts 10 ka c curve finger proof terminal, bi connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly. 165 single core insulated copper wire of 6 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 166 single core insulated copper wire of 4 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 167 single core insulated copper wire of 4 sqmm of black colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 168 single core insulated copper wire of 2.5 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 169 single core insulated copper wire of 2.5 sqmm of black colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 170 single core insulated copper wire of 2.5 sqmm of green colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 695. 171 single core insulated copper wire of 1.5 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 695. 172 single core insulated copper wire of 1.5 sqmm of black colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 695. 173 single core insulated copper wire of 1.5 sqmm of green colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 696. 174 round sheet of plastic for fan box. 175 round sheet of bakelite for junction box. 176 lamp holder, pvc / polycarbonate type. 177 switch piano flush type single pole, one way 5 amp. 178 socket piano flush type single pole, one way 5 amp. 179 multi socket outlet piano flush type 5 pin 5 & 15 amp. 180 fan regulator socket type. 181 capacitor 3.15 mfd as per is code. 182 modular white cover plate with frame, 1 module / 2 module. 183 modular white cover plate with frame, 3 module. 184 modular white cover plate with frame, 6 module. 185 modular white cover plate with frame, 8 module. 186 modular white cover plate with frame, 12 module. 187 modular bell push switch, 6 a, 1 module. 188 modular socket, 6a 2 / 3 pin combined, 2 module. 189 modular switch 6a, 1 module. 190 modular switch 16 amps, 1 module with indicator. 191 modular socket 16 amps, 6 pin, 2 module. 192 modular fan step regulator, 120w 1 module. 193 modular blank switch 1 module. 194 ac plug top 2p +earth. 195 ac socket 2p +earth. 196 bakelite sheet 4 x 4. 197 bakelite sheet 7 x 4. 198 bakelite sheet 8 x 10. 199 bakelite sheet 11 x 12. 200 flexible pipe of 20 mm dia. 201 screws of 1.0 inch. 202 screws of 1.5 inch. 203 screws of 2.5 inch....

Military Engineer Services - Punjab

24846393 periodical services incl camouflaging paint , plaster works to the amn sheds and other bldgs in technical area at mil stn dappar under ge ( p ) dappar , m&l for two coats of synthetic enamel paint camouflage paint including praparation of old steel surfaces to receive painting , washing and cleaning , of any description over 10 cm width or girth not otherwise described complete all as specified and directed . , m&l for applying acrylic thick wall care putty on internal / external surfaces of walls / ceilings / soffits ( thickness vary from 1 . 5 to 2 . 5 mm as required for desired smoothness and levelling of surfaces in two or more layers ) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed . make of wall putty : jk wall putty / birla wall care putty / bison wall putty . notes : ( i ) the prepared surface after wall putty , the contractor will inform to the ge as well as to the engineer in charge for site inspection before applying further finishes . please note that the further finishes work will start only after approval of the prepared surface from the ge as well as to the engineer in charge through site order . , applying 02 coats of exterior emulsion paint ( light shade ) @ 5 sq . m / litre / 2 coats by using roller / brush to external walls / rcc surfaces / soffits of chajjas / roof projections / cantilevers / balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq . m / litre / 1 coat by roller burss or or mechnical spray all as directed by engr in charge as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed . make of exterior wall primer : asian / berger / nerolac [ best quality ] . make of exterior emulsion : asian ( ace ) / berger ( walmasta ) / nerolac ( suraksha superior ) , taking down cement plaster on brick wall on concrete surfaces incl hacking for key racking out joints scrubbing down with water etc . , m&l for cement plastering 15mm thick in two layers ( 10mm and 5mm respectively ) in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturers instructions on brick work or concrete surfaces or in chajjas / parapet walls etc finished even and smooth without using extra cement complete all as specified and as directed by engineer in charge . note : wpc will be measured and paid separately . , supply only integral liquid water proofing compound complete all as specified & as directed by engineer in charge . make : pidilite / sika , m&l for applying 02 coats of interior emulsion paint ( light shade ) @ 10 sq . m / litre / 2 coats by using roller or mechnical spray all as directed by engr in charge to wall surfaces over & including a coat of interior wall primer @ 10 sq . m / litre / 1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed . make of interior wall primer : asian / berger / nerolac [ best quality ] . make of interior emulsion : asian ( tractor ) / berger ( bison ) / nerolac ( beauty smooth ) . , m & l for preparing existing treated surfaces of external walls / rcc surfaces / soffits of chajjas / roof projections / cantilevers / balcony etc including cornices and applying one coat of cement base paint @ 5 sq . m / kg / 1 coat by using following brands of cement based paint by roller complete all as specified & as directed by engineer in charge . make of cement paint : snowcem plus ( snowcem paints ) / asian / berger , m & l for preparing existing treated surfaces on ceiling including cornices and applying one coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream . this shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth . 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream . about 1 . 3 kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant . small quantity of ultramarine blue ( upto 3 gm per kg of lime ) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by engineer in charge ....

Indian Army - Punjab

24515907 supply of maintenance stores ( 1 ) 1 1 supply of maintenance stores ( 1 ) 2 1.01 acrylic sheets size 8 x 4 item1 8 nos 3 1.02 bib cock 15mm item2 15 nos 4 1.03 bricks sub class `b of size 230mm x 115mm x 75mm conforming to is 1077 1986 having smooth rectangular faces with sharp corners, metallic in sound and free from flaws and cracks. item3 5398 nos 5 1.04 decorative1p 54 bulk head fitting with deep drawn crca powder coated body opal acrylic deffuser complete with cfl holder suitable for rectro fit cfl of 20 watt, 230 volt grade.make : bajaj / cg / wipro / philips. item4 13 nos 6 1.05 ceiling fan 1200mm sweep with electronic regulator, ac 220v make orient / bajaj / crompton / havells item5 25 nos 7 1.06 ceiling rose with three terminals with isi mark, 230 volt grade. make : anchor / kinjal / ess ess / havells. item6 25 nos 8 1.07 pozzolana portland cement ( ppc ) packed in 50 kgs hdpe bags conforming to is 1489 make : ultra tech / ambuja / acc or equivalent. item7 245 bags 9 1.08 ceramic wash basin of size 550mm x 400mm with connection pipes and waste coupling including waste disposal pipe whb conforming to is 2556 part iv 2004. make:cera / hindware / juaguar item8 1 nos 10 1.09 cfl 18w make: havells / bajaj / philips item9 71 nos 11 1.1 cgi sheet 6 x 3 ft item10 5 nos 12 1.11 compact led bulb 7 watt with complete fittings . make : havells / surya / anchors / bajaj item11 15 nos 13 1.12 distribution box 8 way item12 2 nos 14 1.13 pre fab mild steel door of size 1200mm x 2100 mm ( double paneled ) made out of angle iron 40mm x 40mm x 6mm , ms black sheet 4mm thick with suitable strong hold fasts for embedding in concrete / wall as per is 1038 1983. doors to be provided with door stoppers. item13 8 nos 15 1.14 exhasust fan fresh air fan with lowers, single phase 230 / 240 volt of size 300mm sweep with shutter make : usha / bajaj / khaitan item14 8 nos 16 1.15 fan regulator electronic, make : bajaj electric item15 11 nos 17 1.16 fine sand shall be clean, sharp, angular hard and durable free from adherent coating and shall not contain clay, mica and other impurities. the maximum quantities of clay and fine silt in sand shall not be more than 5% by mass as per is 383 1970. item16 31 cum 18 1.17 fire extenguisher 1 kg make fireking item17 1 nos 19 1.18 flexible wire pvc insulated twin core twisted of size 23 / 0.076 with copper conductor. make : havells / gloster / plaza item18 100 mtrs 20 1.19 glass putty item19 30 kgs 21 1.2 holder pendent / batten, make : anchor item20 49 nos 22 1.21 insulation tape. per roll 30 mtr length, make : steel grip / equivalent with isi mark item21 5 nos 23 1.22 led tube light fitting 20 watt, ultra bright glass shell, glare fee, wide angle, double side connection retofit led tube g 13 lamp, holder complete white finishing accessories. make: bajaj / philips / havells. item22 13 nos 24 1.23 lightening arrester system: ( conforming to is 2309 1969 lightening arrester system. item23 1 nos 25 1.24 lime item24 50 kgs 26 1.25 looking irror of size of 450 x 600mm duly moduled with pvc channel , the mirror glass will be of 4mm thick item25 2 nos 27 1.26 loop hole shutter with frame frame of angle iron 40x40x6 with 8 nos hold fast of flat iron 25 x 5mm ( 20cm long ) and cover sheet miled steel plate 12mm thick of size 750mmx 600mm and 2x 100mm size ms butt hinge welded with frame and 01 x ms handle and 01 x ms tower bolt. item26 16 nos 28 1.27 mcb 32 amp dp with cover make : havells / standard / indonesian item27 22 nos 29 1.28 mcb 40 amp single pole make : havells / standard / indonesian item28 8 nos 30 1.29 mcb 63 amps 4 pole make : havells / standard / indonesian item29 3 nos 31 1.3 mcb box 6 way make : havells / standard / indonesian item30 1 nos 32 1.31 paint black colour make : asian / shalimar / berger. item31 46 ltrs 33 1.32 paint blue colour make : asian / shalimar / berger. item32 1 ltrs 34 1.33 paint brown colour make : asian / shalimar / berger. item33 1 ltrs 35 1.34 painting brush 2 make : lucky / 555 / amar item34 24 nos 36 1.35 painting brush 4 make : lucky / 555 / amar item35 21 nos 37 1.36 paint bus green enamel make : asian / shalimar / berger item36 15 ltrs 38 1.37 paint og colour make : asian / shalimar / berger item37 199 ltrs 39 1.38 red oxide primer conforming to is 104 1979 make : berger / shalimar / asian ( 1st quality ) item38 89 ltrs 40 1.39 paint sand colour make : asian / shalimar / berger. item39 20 ltrs 41 1.4 paint white colour make : asian / shalimar / berger. item40 6 ltrs 42 1.41 paint yellow colour make : asian / shalimar / berger. item41 10 ltrs 43 1.42 pbs roll item42 1 roll 44 1.43 switch piano flush type 5 amp, 230 volt grade with isi mark. make : anchor / kinjal / ess ess / havells. item43 51 nos 45 1.44 pillar cock 15mm dia item44 2 nos 46 1.45 pvc casing capping double locked box type 1 x 6’ long with all fittings / fixtures, medium grade with accessories, with isi marked. make : diplast / regal / vimco item45 9 nos 47 1.46 pvc insulated copper wire multi strand 1.5 sqmm 2 core item46 1 mtr 48 1.47 pvc valveless symphonic action type flushing cistern 10 ltr capacity liw level, white with inlet, ball valve, float and hnadle including all connected fittings and cantilever supports. make: commander / pryag / hindustan item47 1 nos 49 1.48 sand bag 38x80 cm item48 159 bags 50 1.49 water tank 500 ltrs capacity rotational moulded three layer polyethylene water storage tank ( cylindrical vertical with closed top ) including necessary fittings / accessories complete as per is 12701 1989, with angle iron staging as per drg att. make: sintex / polycon. item49 1 nos 51 1.5 socket 15 amp 240 v 5 pin, make :kinjal item50 3 nos 52 1.51 socket 5 amp 240v 5pin make :kinjal item51 4 nos 53 1.52 solar battery 75 ah, 12 v make exide / amaron / luminous / microtec or equivalent item52 11 nos 54 1.53 solar led 18 watt make havells / crompton / / bajaj / surya / halonix / syska or equivalent item53 11 nos 55 1.54 solar panel 100 w item54 6 nos 56 1.55 stone aggregate shall be crushed stone 20mm graded conforming to is 383 1970 and shall be clean hard tough, durable and of uniform quality through out. the aggregate shall be free from soft disintegrated materials, vegetable and other organic impurities. item55 17 cum 57 1.56 stop cock brass 15mm dia. nmake:suraj / sona / krishna item56 10 nos 58 1.57 switch socket combination multipurpose 15 amps 240 volt grade with isi mark. make : anchor / kinjal / ess ess / havells. item57 35 nos 59 1.58 switch socket combination multipurpose 5 amps 240 volt grade with isi mark. make : anchor / kinjal / ess ess / havells. item58 57 nos 60 1.59 switch socket combination 15 amps with pvc box with isi mark, make : anchor / bajaj / havells item59 5 nos 61 1.6 tube light fitting 36 / 40 w , make : bajaj electric item60 103 nos 62 1.61 wall putty make : asian / shalimar / jk item61 4 kgs 63 1.62 water tank 1000 ltrs capacity rotational moulded three layer polyethylene water storage tank ( cylindrical vertical with closed top ) including necessary fittings / accessories complete as per is 12701 1989, with angle iron staging as per drg att. make: sintex / polycon. item62 2 nos 64 1.63 window glass of size 600x600 acrylic sheet item63 50 nos 65 1.64 wire pvc insulated cable 1.5 sqmm multistandard copper conductor single core 1100v grade conforming to is 694 / 1990 a roll of 90m long of make : havells / anchor / finolex / fine / plaza item64 380 mtrs 66 1.65 wire mesh for window 4.5 x 4.5 ft item65 11 nos 67 1.66 wire pvc insulated cable 1.5 sqmm multi standard copper conductor single core 1100v grade conforming to is 694 / 1990 a roll of 90m long of make : havells / anchor / finolex / fine / plaza item66 2 roll...

Indian Army - Punjab

19952561 supply of water supply stores for the financial year 2019 20: 1.1 pvc valveless symphonic action type flushing cistern 10 ltr capacity liw level, white with inlet,ball valve, float and hnadle including all connected fittings and cantilever supports. make: commander/pryag/hindustan 1.11 pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with ot without lettered hot cold with long screwed shanks & fly nuts, screwed for iron pipes & fixed, 15mm bore dia 1.12 pillarcock cp 15mm fancy type , make:jaquar/parco/gem 1.13 bib taps, cast copper alloy, but chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed, 15mm bore 1.14 stop valves cast copper alloy, but chromium plated, screwed down high pressure with crutch or butterfly hnadle screwed both ends for iron pipe or for unions & fixed, 15mm bore make:jaquar/parco/gem 1.15 gate valve brass 20mm dia, make: flowjet/ball valves india. 1.16 float valve 20mm with brass rod. make prayag 1.17 20mm brass stop conforming to is 781 1984,make :suraj/sona/krishna 1.18 gi pipe 20 mm dia med grade with all fitting isi mark screwed at both ends all as per is 1239. make tata/jindal/neco. 1.19 gi socket 20mm dia conforming to is 1239 2004 . make tata/jindal/neco. 1.2 gi union 20 mm dia conforming to is 1239 2004. make tata/jindal/neco. 1.21 gi tee 20 mm dia conforming to is 1239 2004 . make tata/jindal/neco. 1.22 gi nipple 20mmx 3 conforming to is 1239 2004 , make tata/jindal/neco. 1.23 gi nipple 20mmx 4 conforming to is 1239 2004 , make tata/jindal/neco. 1.24 gi elbow 20mm dia conforming to is 1239 2004 , make tata/jindal/neco. 1.25 20mm dia check nut for pvc water tank make : tata/jindal/ravindra 1.26 gi pipe 15 mm dia med grade with all fitting isi mark screwed at both ends all as per is 1239. make tata/jindal/neco. => open tender...

Indian Army - Punjab

17193467 supply of miscellaneous stores for operational work fy 2018 19: 1.2 stop valves cast copper alloy, but chromium plated, screwed down high pressure with crutch or butterfly hnadle screwed both ends for iron pipe or for unions & fixed, 15mm bore. make : sona / shakti 1.21 vitreous china, squatting pan orissa pattern of size 580 x 440mm white with integral foor rests ( excluding flushing cistern and flush pipe. make : cera / hindustan 1.22 pvc valveless symphonic action type flushing cistern 10 ltr capacity liw level, white with inlet, ball valve, float and hnadle including all connected fittings and cantilever supports. make: commander / pryag / hindustan 1.23 cp brass shower rose 15mm bore 100mm long. make : sona / shakti 1.24 red oxide make shalimar / asian / berger 1.25 sand paper 1.26 snowcem / cemkote external wall make shalimar / asian / berger 1.27 terpentine oil make : prakash 1.28 oil bound distermper make shalimar / asian / berger 1.29 lime...

Punjab Technical University - Punjab

16376299 quotation for control systems lab of ee department, ikgptu main campus synchro transmitter & receiver trainer , ac servomotor torque/speed characteristics trainer , dc servomotor torque/ speed characteristics trainer , study various electro mechanical transducers , measurement of force by strain gauge using cantilever beam , compensating circuits...

Indian Army - Punjab

16243286 supply of miscellaneous stores: 1.3 pvc caping and casing of size 25mm x 16mm , 2mtr long with accy make : plaza/sahil/topson conforming to is 14927 (part i) 1.31 pvc bend 25mm dia 1.32 l shapped security/accn light with 2ft long tube light and electronic ballast choke complete 1.33 pvc wall gitty 1.34 ms pole 3150mm long having 40mm dia (nb) fitted with base plate 200x200x8mm thick with 04 nos hole 12mm for foundation bolt fixing with coach 1.35 smoke alarm 1.36 instant water heater gyser of capacity 5 ltrs including 4 nos nut & bolts for each and connected accessories. make : bajaj/usha/havels 1.37 gi pipe 20mm dia with isi mark incl socket, tee, union etc incl fittings make : tata/jindal/amba 1.38 ball brass valves, high pressure with polythene float & fly nut complete, screwed for iron pipe or brass ferrule & fixed 20mm bore 1.39 soap case any type fixed to plugs with chromium plated brass screws 1.4 towel rail 600mm long & including chromium plated brass screw & wooden/plastic cleats (minimum weight 190gms) 1.41 stainless steel peg sets of six hooks 1.42 adhesive for pvc pipe 100 gms 1.43 salt glazed stoneware drain pipes of dia 150mm including connectors i.e bends, y junction, gully trap etc 1.44 gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe & fixed, 20mm 1.45 pvc traps p or s type 1.46 vitreous china wash down water closet pan ewc including fixing bolt, with flushig pipe to match the ewc and pvc seat cover, toilet paper holder, p or s trap complete including all accessories . make : hindustan/cera/parryware/indians 1.47 vitreous china wash basin wihte flat back or angle back type size 630x450mm including waste pipes, waste fittings floor traps etc, mounted on cantilever brackets complete as specified. make : cera/hindustan 1.48 gi tubes of 15mm dia medium grade galvanised including all type of connectors make : ravindra/jindal ...

Indian Army - Punjab

16116059 supply of miscellaneous stores for operational works for the financial year 2018 19: 1.31 pvc bend 25mm dia 1.32 l shapped security/accn light with 2ft long tube light and electronic ballast choke complete 1.33 pvc wall gitty 1.34 ms pole 3150mm long having 40mm dia (nb) fitted with base plate 200x200x8mm thick with 04 nos hole 12mm for foundation bolt fixing with coach 1.35 smoke alarm 1.36 instant water heater gyser of capacity 5 ltrs including 4 nos nut & bolts for each and connected accessories. make : bajaj/usha/havels 1.37 gi pipe 20mm dia with isi mark incl socket, tee, union etc incl fittings make : tata/jindal/amba 1.38 ball brass valves, high pressure with polythene float & fly nut complete, screwed for iron pipe or brass ferrule & fixed 20mm bore 1.39 soap case any type fixed to plugs with chromium plated brass screws 1.4 towel rail 600mm long & including chromium plated brass screw & wooden/plastic cleats (minimum weight 190gms) 1.41 stainless steel peg sets of six hooks 1.42 adhesive for pvc pipe 100 gms 1.43 salt glazed stoneware drain pipes of dia 150mm including connectors i.e bends, y junction, gully trap etc 1.44 gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe & fixed, 20mm 1.45 pvc traps p or s type 1.46 vitreous china wash down water closet pan ewc including fixing bolt, with flushig pipe to match the ewc and pvc seat cover, toilet paper holder, p or s trap complete including all accessories . make : hindustan/cera/parryware/indians 1.47 vitreous china wash basin wihte flat back or angle back type size 630x450mm including waste pipes, waste fittings floor traps etc, mounted on cantilever brackets complete as specified. make : cera/hindustan 1.48 gi tubes of 15mm dia medium grade galvanised including all type of connectors . make : ravindra/jindal 1.49 gi socket 15mm isi marked 1239 make : unique/tata/jindal 1.5 gi elbow 15mm isi marked 1239 ...

Punjab Technical University - Punjab

15064361 quotation for control systems lab of ikgptu main campus synchro transmitter & receiver trainer , ac servomotor torque/speed characteristics trainer , dc servomotor torque/ speed characteristics trainer , measurement of force by strain gauge using cantilever beam , compensating circuits...

Military Engineer Services - Punjab

14869490 tender for bazaar supply for b / r item under age b / r ii of ge ( e ) fzr cantt 1.00 supply only modular bricks; common burnt clay building bricks, sub class ‘a’ designation 75 2.00 supply only fine aggreagate (sand) for concrete 3.00 supply only cement ordinary portland 4.00 supply only, galvanised steel tubes, mediumt grade 15mm bore 5.00 supply only,galvanised steel tubes, mediumt grade 20 mm bore 6.00 supply only india rubber washers for pillar taps etc, 20 mm and under 7.00 supply only,vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) 8.00 supply only, vitreous china, semi pedestal pattern (anglo indian type) (ditto) 9.00 supply only,vitreous china squatting pan of pattern “long pan”, size 580 mm white with ‘p’ or ‘s” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) 10.00 supply only, pvc valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets 11.00 supply only,brass chromium plated shower rose 125mm size 12.00 supply only,flush pipe of polyethylene of low or high density or pvc. 32 mm dia, for low level cistern 13.00 supply only,toilet paper holder, vitreous china, box type, white 14.00 supply only, vitreous china urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) 15.00 supply only,plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device 16.00 supply only,vitreous cliina wash basin, wliile, flat back, size 580x450irun (for hospilal use) excluding taps, waste, chain and plug and porcelain stopper but including brackets 17.00 supply only, vitreous cliina wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets 18.00 supply only 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers 19.00 supply only,soap dish, vitreous china white, approximate size 160x 160x90mm 20.00 supply only,sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long 21.00 supply only, stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm® 22.00 supply only,plastic water tank, approved quality capicity 500 ltrs 23.00 supply only, plastic water tank, approved quality capicity 1000 ltrs 24.00 supply only,pvc (swr) pipes, single socketed, in any length , with rubber rings 75 mm dia® 25.00 supply only,pvc (swr) pipes, single socketed, in any length , with rubber rings 110mm dia® 26.00 supply only,pvc (swr) pipes, double socketed, in any length , with rubber rings 75mm dia® 27.00 supply only, pvc (swr) pipes, double socketed, in any length , with rubber rings 110mm dia® 28.00 supply only,bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fancy type 15 mm size 29.00 supply only,bib tap 15 mm size,standard of ptmt any colour high pressure screwed for iron pipe and fixed.(minimum weight 15mm 90gms/20mm 125gms). 30.00 supply only,bib tap 20 mm size,standard of ptmt any colour high pressure screwed for iron pipe and fixed.(minimum weight 15mm 90gms/20mm 125gms). 31.00 supply only, pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe, fancy type 15 mm size 32.00 supply only.pillar taps 15 mm size, of ptmt any colour high pressure screwed for iron pipe , fancytype(minimum weight 15mm 110gms)® 33.00 supply only,stop valve 15 mm size,of ptmt any colour high pressure screwed for iron pipe (minimum weight 15mm 90gms/ 20mm n92gms) ® 34.00 supply only, stop valve 20 mm size,of ptmt any colour high pressure screwed for iron pipe (minimum weight 15mm 90gms/ 20mm n92gms) ® 35.00 supply only, pvc connections 15mm size with ptmt nuts of length 300mm 36.00 supply only, pvc connections 15mm size with ptmt nuts of length 450mm 37.00 supply only, pvc connections 15mm size with ptmt nuts of length 600mm 38.00 supply only, towel rail 450mm long of ptmt including chromium plated brass screws and wooden/plastic cleats (minimum weight 170gms 39.00 supply only, towel rail 600mm long of ptmt and including chromium plated brass screws and wooden/plastic cleats. (minimum weight 190gms) 40.00 supply only,bends (any radius), diminishing pieces or tapers (larger bore measured ) 100 mm bore 41.00 supply only,asbestos cement pipes in any length with cement joints; fixed to walls 100 mm bore 42.00 supply only, pvc (swr) floor trap, plain with grating including jointing with solvent cement 43.00 supply only,pvc (swr) multi floor trap with grating including jointing with solvent cement ® 44.00 supply only machine cut kota stone slab flooring 20 25mm thick 45.00 supply only, glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match 46.00 supply only non skid ceramic tiles 300 x 300 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. any color 47.00 supply only ,nipple 15 mm size,suitable for hdpe water tank. (minimum weight 15 mm 38gms/20mm 45gms /25mm 65gms 48.00 supply only ,nipple 20 mm size,suitable for hdpe water tank. (minimum weight 15 mm 38gms/20mm 45gms /25mm 65gms 49.00 supply only ,waste coupling of ptmt 32 mm bore (half or full threaded) . (minimum weight 32mm 45gms/40mm 60 gms) 50.00 supply only ,waste coupling of ptmt 40 mm bore (half or full threaded) . (minimum weight 32mm 45gms/40mm 60 gms) 51.00 supply only ,grating doom 100mm dia of ptmt (minimum weight 25gms) 52.00 supply only ,grating doom 125 mm dia with waste hole of ptmt. (minimum weight 40gms) 53.00 supply only ,grating round 140 mm size of ptmt. (minimum weight 50gms) 54.00 supply only, swivel shower of ptmt any colour for fixing with 15mm pipe. (minimum weight 40gms) 55.00 supply only,shelf of ptmt fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight300gms 56.00 supply only,galvanised steel wire cloth. 0.63 mm nominal dia of wire and average width of aperture 1.40mm 57.00 supply only,sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane 3.0 mm thick 58.00 supply only, 2nd class hardwood clean sawn boards or planks, width n exc. 25 cm,thickness of board 30 mm 59.00 supply only, mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete 60.00 supply only, mild steel pressed handles, oval type, stove enamelled black, size of handle 150 mm 61.00 supply only,aluminium handles, cast type, anodised,size of handle 150 mm 62.00 supply only,mortice lock, brass made, of 4 levers, vertical type, size 100 mm 63.00 supply only, 6 mm thick,plywood, grade bwr, type bb, fixed with screws to timber frame work 64.00 supply only, perforated particle boards or tiles for insulation and accoustic purposes, 60cm x 60cm in size, thickness 18/19 65.00 supply only, pink primers for wood and wood based materials 66.00 supply only, aluminium red oxide primer for steel and iron work 67.00 supply only, synthetic enamel paint (ordinary tint) 68.00 supply only, plastic emulsion paint 69.00 supply only tank cover of water storage tank capicity 500/1000 ltrs 70.00 supply only, union 15 mm steel medium grades 71.00 supply only, union 20 mm steel medium grades 72.00 supply only, elbow 15 mm steel medium grades 73.00 supply only, elbow 20 mm steel medium grades 74.00 supply only, sockets 15 mm steel medium grades 75.00 supply only, sockets 20 mm steel medium grades 76.00 supply only, tee 15 mm steel medium grades 77.00 supply only, tee 20 mm steel medium grades 78.00 supply only, reducertee 15 mm steel medium grades 79.00 supply only, reducer sockets 15 mm steel medium grades 80.00 supply only, reducer elbow 15 mm steel medium grades 81.00 supply only, patchmate road repair material 6% modified bitumen antitriping agent pressure sensitive and water proofing (50kg) encapsulating additiru with graded crushed lime stone as per manufacturer instruction....

Punjab Technical University - Punjab

13225217 purchase of fatigue testing machine ( rotating cantilever type ) for solid mechanics laboratory of civil engineering department....

Hindustan Insecticides Limited - Punjab

12592366 tender document for annual maintenance contract for civil maintenance works supply of the following material ( s ) 1 2.8.1 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all kinds of soil. 2 2.27 supplying and filling in plinth with jamuna sand under floors, including watering, ramming, consolidating and dressing complete. 3 4.1.10 providing and laying in position cement concrete of specified grade excluding the cost centering and shuttering – 1:5:10 ( 1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size ) all work up to plinth level 4 5.1.3 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement. 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) . all work up to plinth level 5 5.2.2 reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement. 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) 6 5.9.1 centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete 7 5.9.3 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 8 5.9.5 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 9 5.9.6 centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts 10 5.22.6 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing position and binding all complete upto plinth level : themo mechanically treated bars 11 6.1.2 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundation and plinth in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) 12 6.4.2 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) 13 6.8 brick work 7 cm thick with common burnt clay f.p.s. ( non modular ) brick of class designation 7.5 in cement mortar 1:3 ( 1 cement : 3 coarse sand ) in superstructure above plinth level and upto floor five level. 14 10.1 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 15 11.5 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) and top layer 12mm thick cement hardener consisting of mix 1:2 ( 1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size ) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. this includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. 16 12.50 providing and fixing precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( +0.05 perc. ) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineerin charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 17 13.1.2 12 mm cement plaster of mix : 1:6 ( 1 cement: 6 fine sand ) 18 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 ( 1 cement: 6 fine sand ) 19 13.16.1 6 mm cement plaster of mix : 13.16.1 1:3 ( 1 cement : 3 fine sand ) 20 13.37.1 white washing with lime to give an even shade : new work ( three or more coats ) 21 13.41.1 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work ( two or more coats ) over and including water tinnable priming coat with cement primer 22 13.61.1 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work...

Water Supply And Sanitation Department - Punjab

6053543 providing water supply scheme for village phalora in block sujanpur distt. pathankot . providing and installing deep tubewell 200 mm i/d straight up 107 mtr. depth with 20 mtr. stainless steel strainer with percussion rig complete in all respects. a) construction of one rcc, ohsr 25000 ltrs with height up to fsl 18.00 mtr and 15.50 mtr. up to top bottom slab, including double flanged ci pipes with special lighting conductor, earthling ms steel for tank portion and all other works contingent thereto complete in respect. b) construction of of pump chamber under 25000 liter capacity of ohsr internal size 3.415 x 3.415 mtr. with internal stair case and extended rcc canopy supported over rcc pillars and cantilever portion of 1 meter with gi pipe railing around the canopy pumping machinery chlorination plant supplying, laying and testing of pvc pipe 10 kg and all other works contingent thereto complete in all respect....

Police Headquarters - Punjab

1983046 supply of hook & line (basic reel assy. with brake & carry case, barrel strap, swivel release pulley assy, vice grip clamp assy, rope pull assy, large triple hook assy, double suction cup assy, cantilever clamp assy, pulley release cylinder assy, carabiner, large screw gate, hook setter assy, eod sledge, sriral ground anchor)...