distribution panel Tenders in Punjab

1

Department Of Civil Aviation - Punjab

41001341 bids are invited for 03yrs warranty with manpower and 03yrs camc outdoor ptz cctv camera , indoor ptz cctv camera , outdoor fixed cctv camera , indoor fixed cctv camera , anpr camera , l3 switch 24 and 4 port , l2 switch 24 and 4 port , l2 switch 08 and 4 port , network attached storage , 46 inch display , 2x2 46 inch video wall , workstation type a , workstation type b , console for control room , camera server , video analytic server , anpr server , ntp server , kvm switch , 40 or 42u 19 inch rack , power distribution panel , 20kva 1 plus 1 ups , vms and digital video surveillance control software licence , video analytics software licence , 25mm ms conduit , 25mm pvc conduit , 50mm hdpe pipe , 80mm gi pipe , 12 core armoured ofc , cat 6 utp cables , cat 6 stp cables , 3 core 1.5 sqmm copper conductor cables , 3 core 6 sqmm copper conductor cables , 4 core 16 sqmm aluminium conductor cables , rj45 gangbox , 12 port liu , 24 port liu , 2 fiber and 4 copper port media converter , 4 inch dia, 5 mtr height gi pole , 3 mtr high stainless steel cctv pole , civil work cutting and restoration grrove in granite,tile,concrete flooring surface , civil work excavation and backfilling of soft,hard soil , civil work road cutting and backfilling , civil work horizontal directional digging , earthing with copper plates , itc of complete system , training and documentation , operational maintenance by manpower during warranty period sitc of scctv system at sbs intl airport chandigarh for total quantity : 65958...

Due Date : January 10, 2024

Tender Value : ₹ 9.96 Crore

2

Railtel Corporation Of India Limited - Punjab

40872856 procurement of electrical ( general ) items in connection with up gradation of signalling from standard i to standard ii ( r ) with electronic interlocking ( ei ) at 9 stations under dhw srm & lnk phr sections of firozpur division., supply of 1.1 kv grade lt xlpe. insulated armored aluminium conductor cable, making good the damages end termination with aluminium crimping socket / plugs. provision of cable route markers etc. as required as per technical specification no. is 7098. size ( 2x70 sq. mm ) . ( inspection by , laying of 1.1 kv grade lt xlpe. insulated armored aluminium conductor cable, making good the damages end termination with aluminium crimping socket / plugs. provision of cable route markers etc. as required as per technical specification. size ( 2x70 sq. mm ) . [ warranty period: 12 months after the date of delivery ] , supply of control and distribution panel for 10 kva auxiliary transformer for color light signaling supply in 25kv / ac traction system as per rdso technical specification no tl / spc / psi / cls / 0020 ( 12 / 02 with a&c slips no 1 to 4 latest connection as required. ( inspection by , erection testing and commissioning of control and distribution panel for 10 kva auxiliary transformer for color light signaling supply in 25kv / ac traction system as per rdso technical specification no tl / spc / psi / cls / 0020 ( 12 / 02 with a&c slips no 1 to 4 or latest, connection as required. [ warranty period: 12 months after the date of delivery ] , trenching work for single cable. [ warranty period: 12 months after the date of delivery ] ...

Due Date : December 21, 2023

Tender Value : ₹ Ref. Documents

3

Northern Railway - Punjab

40791829 supply of electrical work in connection with maintenance,repair & replacement of auto change over control, distribution panel board & cable for colour light signalling in rri/p cabin/lc gates and other location including over firozpur division.electrical work in connection with maintenance,repair & replacement of auto change over control, distribution panel board & cable for colour light signalling in rri/p cabin/lc gates and other location including over firozpur division.,...

Due Date : December 15, 2023

Tender Value : ₹ 29.81 Lakhs

4

Ministry Of Micro Small And Meduim Enterprises - Punjab

40662529 bids are invited for wall mounting fan , led flood light , mcb 32 amp 4 pole , socket and switch 6 amp. , pvc wire 1.5 sq mm , pvc wire 2.5 sq mm , mcb single pole 10 amp , mcb isolator 32 amp. , mcb box 10 way , pvc conduit pipe 1 inch , pvc bend 1 inch. , pvc batten 2 inch , pvc batten 1 inch , screw gypsum 1 inch , screw gypsum 1.5 inch , rock drill bit 6mm. , pvc gitti. , 12 modular switch boards 2 sockets, 8 switch with surface box plate white , bus bar 200 amps., 3 phase with neutral , main switch 200 amp., aluminum strip used for 3 phase supply plus neutral, 10 nos , lt distribution panel , copper cable 4.0 core 50 mm sq. , copper thimble 50 mm sq. , copper thimble 95 mm sq. , copper wire 16 mm sq green colour for earthing , copper flexible cable 4 core 2.5 mm sq. , flexible pipe 1 black colour , pipe clamp 1.5 , pipe clamp 2.0 , cable tie 9 , hammer drill bit 6 mm sq. , insulation tapes r.y. b color , d link metal unmanaged gigabit 24 port switch , modular electrical switch and accessories with lan port rj 45 , d link cat 6, 305mtr , rj 45 connector pt rj 45 , 9u rack , io box rj 45 cat 6 information outlet total quantity : 1138...

Due Date : November 20, 2023

Tender Value : ₹ Ref. Documents

5

Ministry Of Micro Small And Meduim Enterprises - Punjab

40568619 bids are invited for lt panel and other electrical works supply and installation of lt panel in the central block electrical power distribution room , supply and installation of lt distibution panel for production shop machines power supply , supply and installation of lt panel for training workshop machines distribution power supply , upgradation of existing fan and lighting power suppply distribution panels of ctr administration building, traiing and production workshop and central block training lab , supply and installation of lt panel in gen set room for maintenance, ppc, main store including raw material store power hacksaw, welding work shop , supply and installation of lt distibution panel in gen set room for generator and main incoming power supply distribution total quantity : 21...

Due Date : November 14, 2023

Tender Value : ₹ Ref. Documents

6

Ministry Of Defence - Punjab

39844811 bids are invited for feeler gauges engineering metrology as per is 3179 ( q3 ) , supply and fixing exhuast fan steel body ac single phase 230 v of size 300mm , supply and fixing exhuast fan steel body ac single phase 230 v of size 380mm , supply and fixing exhuast fan steel body ac single phase 230 v of size 450mm , m and l for pointing wiring with 1.5 sqmm nominal area pvc insulated frls unsheathed multistrand 1100 volts , s and f switch piano flush type single pole one way 6 amps. , s and f ceiling rose surface bakelite 65x50mm three terminals complete all as specified. , excavation in trenches in soft3 loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre , returning, filling in trenches soil including spreading leveling and well ramming in layers , removal of surplus excavated soil to a distance not exceeding 50metre and depositing , sand cushioning with a layer of dry river sand 80mm thick before laying of cable and 150mm thick , brick protection with locally available sub class b bricks old size laid flat and dry , gi pipe light grade 40mm dia bore for cable protection fixed to pole wall , earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick , supply laying and testing cable xlpe insulated screened pvc bedded galvanized steel strip , supply and fix mcb db load line enclosuer double door type tpn 4 way , supply and fix mcb sp 6 to 32 amp 240 volt 10 ka , supply and fix lt feeder pillar outdoor type with 3.15mm crca sheet consisting of incoming and outgoing mccbs 3 phase , earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases , m and l test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm , supply and fix flame proof db 6 way enclosure size 300x300x190mm flp lighting distribution panel , m and l for flame proof pointing wiring with 1.5 sqmm nominal area pvc insulated frls , flame proof weather proof rotary switch, single pole on and off with cable termination box in lm 6 of 16 amps rating 250 volts , s and r of flame proof submain wiring alongwith earth wire with 2 x 04 sqmm plus 1x04 sqmm earth wire , supply and fixing led light fitting 2x16 watt flame proof cmri certified recommended for gas , earthing with gi earth plate of size 600mm 600mm 6mm thick using gi strip 25mm 4mm , supply and fixing gi wire 4mm dia , supply and fix flame proof exhaust fan of size 450mm along with louvers including cutting hole in the wall all as directed , supply and fix db spn 12 way double door alongwith 200 amp busbar , supply and fix mcb spn 06 to 32amp 10 ka , supply and fix mcb sp 06 to 32amp 10 ka total quantity : 421...

Due Date : October 04, 2023

Tender Value : ₹ Ref. Documents

7

Military Engineer Services - Punjab

39474893 tender for repair / replacement of lt distribution system at mil stn dappar ; 1 disconnecting & taking out old unserviceable lt cable of any size complete all as specified and as directed by engineer in charge. 2 supply, laying, jointing, connecting, testing & commissioning ug cable xlpe insulated, screened, pvc bedded, galvanised steel strip armoured electric power cable ( heavy duty 1100 volts grade with standard aluminium conductor of cross sectional area 630 sqmm x 3.5 core including two suitable size of both side end termination joint with thimbling / lugsand all other connnected connectionall as specified and directed by engr in charge.note ( a ) . the quoted rate is deemed to be inclusive of arranging respective shutdown, disconnection of cables, commissioning of feeder after the completion of job and inclusive of any minor spares and jobs required for the completion of the job. ( b ) the cable must be without joint from one end to another end ( c ) . the cost of excavation, returning, filling, removal and pcc cable covers will be measured and paid under relevant items of this schedule. 3 all as per ser item no 2 here in before but size of lt under ground cable 120 sqmm 3.5 core. 4 all as per ser item no 2 here in before but size of lt under ground cable 70 sqmm 3.5 core. 5 all as per ser item no 2 here in before but size of lt under ground cable 50 sqmm 3.5 core. 6 all as per ser item no 2 here in before but size of lt under ground cable 35 sqmm 3.5 core. 7 all as per ser item no 2 here in before but size of lt under ground cable 16 sqmm 4 core. 8 excavation in trenches in soft / loose / hard soil n exc 1.5 m wide and not exc 1.5 m in depth and getting out including forming bottom to required level or slope for laying pipes / laying of cable complete all as specified and as directed by engineer in charge. 9 returning filling in soft / loose soil in trenches including spreading, leveling and well ramming in 25 cm thick layers complete all as specified and as directed by engineer in charge 10 removal of surplus soil to a distance n exc in 50 m and deposited where directed at a level n exc 1.5 m above the starting point complete all as specified and as directed by engineer in charge. 11 material and labour sand cushioning ( dry sand ) to underground cable for cable protection 23 cm thick in two layers ( 8 cm thick before laying of cables and 15 cm thick after laying the cable and punning down the sand to 18 cm thickness. ) complete all as specified and as directed by engineer in charge. ( note: only punned thickness 18 cm of sand shall be measured for payment purposes ) . 12 material and labour precast concrete cable cover, class lv, type 1 with peak, size 250mm x 150mm x 40mm complete all as specified and as directed by engineer in charge. 13 material and labour making bore to road width for providing gi pipe medium / light grade both end socketed for passing armoured cable complete all as specifed. 14 material and labour for galvanized iron tubing size 100 mm bore ( light grade ) with all necessary fittings laid in trenches under road crossing or fixed on poles / walls / under floors for cable protection complete all as specfied and as directed. 15 material and labour for galvanized iron tubing size 80 mm bore ( light grade ) with all necessary fittings laid in trenches under road crossing or fixed on poles / walls / under floors for cable protectioncomplete all as specfied and as directed. 16 material and labour for galvanized iron tubing size 40 mm bore ( light grade ) with all necessary fittings laid in trenches under road crossing or fixed on poles / walls / under floors for cable protectioncomplete all as specfied and as directed. 17 material and labour for earthingwith galvanised iron earth plate of size 600x600x6mm thick buried directly in ground not less than 2.25m below normal ground level, earth plate packed on all sides with charcoal mixed with salt in alternate layers of 15 cm thickness connected by galvanised iron earth strip 32x6mm soldered & riveted to earth plate, galvanised iron earth strip will be provided by using 50mm bore galvanised iron pipe ( light grade ) earth plate to transformer body and neutralor test point of transformer, including flat iron clamp 25x3mm including bolts, nuts and washers complete including watering galvanised iron pipe 20 mm dia light grade 2.5m long the earthing includes pcc pit including necessary earth works and disposal of surplus soil to a distance not less than 50m, chamber of pcc 1:4:8 type d 2 using 40mm graded stone aggregate, coping shall be of pcc 1:3:6 type c i using 20mm graded stone aggregate, rcc pit cover 50mm thick in 1:2:4 type b i using 20mm graded stone aggregate, reinforced with 8mm dia @ 15cm c / c complete all as shown on sketch no 3 of ssr i of 2009 and as specified and as directed by engr in charge. 18 material and labour earth continuity conductor gi of 32x6 mm of gi strip by means of bolts, nuts, check nuts and gi washers complete all as specified. 19 supply and fix cable jointing kit for 1100 v grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3.5 core xlpe, armoured, aluminium conductor cable of size upto 25 to 50 sqmm, core outdoor type and taking down fault complete all as specified and directed by engr in charge. 20 supply and fix cable jointing kit for 1100 v grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3.5 core xlpe, armoured, aluminium conductor cable of size upto 70 to 120 sqmm, core outdoor type and taking down fault complete all as specified and directed by engr in charge. 21 supply and fix cable jointing kit for 1100 v grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3.5 core xlpe, armoured, aluminium conductor cable of size upto 150 to 185 sqmm, core outdoor type and taking down fault complete all as specified and directed by engr in charge. 22 supply and fix cable jointing kit for 1100 v grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3.5 core xlpe, armoured, aluminium conductor cable of size upto 240 to 630sqmm, core outdoor type and taking down fault complete all as specified and directed by engr in charge. 23 disconnecting, dismantling and taking out old burnt unserviceable mccb from lt distribution panels after arranging necessary electric shutdown, supply & fix mccb fp, 36ka, 400 amps with thermal magnetic release type ics = 100% icu, adjustable over load setting: 0.4 1.0 x in, adjustable short circuit for each phase from 1.5 8 x in, . note quoted rate is deemed to be inclusive of minor jobs and minor spares required for fitment of mccb in the existing panel. 24 disconnecting, dismantling and taking out old burnt unserviceable mccb from lt distribution panels after arranging necessary electric shutdown, supply & fix mccb tp, 25ka, 250 amps with thermal magnetic release type, ics = 100% icu, adjustable over load setting: 0.4 1.0 x in, adjustable short circuit for each phase from 6 10 x in, all as specified and directed by engr in charge. 25 disconnecting, dismantling and taking out old burnt unserviceable mccb from lt distribution panels after arranging necessary electric shutdown, supply & fix mccb tp, 25 ka, 200 amps with thermal magnetic release, ics = 100% icu, adjustable over load setting: 0.8 1.0 x in, adjustable short circuit for each phase from 6 10 x in, all as specified and directed by engr in charge. 26 disconnecting, dismantling and taking out old burnt unserviceable mccb from lt distribution panels after arranging necessary electric shutdown, supply & fif mccb tp, 25 ka, 160 amps with thermal magnetic release, ics = 100% icu, adjustable over load setting: 0.8 1.0 x in, adjustable short circuit for each phase from 6 10 x in, all as specified and directed by engr in charge. 27 disconnecting, dismantling and taking out old burnt unserviceable mccb from lt distribution panels after arranging necessary electric shutdown, supplty & fix mccb tp, 25 ka, 125 amps with thermal magnetic release, ics = 100% icu, adjustable over load setting: 0.8 1.0 x in, adjustable short circuit for each phase from 6 10 x in, all as specified and directed by engr in charge. 28 supply and replace existing unservicable indicating lamp led type suitable to operate on 230 volts ac supply of r / y / b colour as per site requirement all as specified and directed. 29 supply and replace existing unservicable selector switch for voltmeterall as specified and directed by engr in charge.. 30 supply and replace existing unservicable selector switch for ammeter all as specified and directed by engr in charge. 31 supply and replace existing unserviceable ct as that of existing ratio and model suitable for 3 phase supply all as specified and directed by engr in charge. 32 material & labour for dismantling old unserviceable lt panel along with disconnecting connected cables, supplying, installing, testing and commissioning of 415volts 3phase 4 wire factory fabricated and tested all as per existing iec 60439 part 1, floor mounted, ip 55 grade, outdoor double doortypebus coupler lt cubical panel made out of3.15 mm crca ms sheet duly powder coated with seimens grey shade ral 7032, dust and veremin proof with suitable size tpn pvc sleeved aluminium bus bar including. angle iron base frame of 40x40x6mm. panel should be mounted / grouted on 150 mm thick pcc ( 1:4:8 ) type d2 below nearest greound level and should be with 400 mm offsets on all 04 sides of the panel complete and should be inclusive of following fitted in accessories : a. incoming: ( i ) mccb 630 amps , 415 v 4 pole 36 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 02 no. b. bus coupler ( ii ) mccb 630 amps , 415 v 4 pole 36 ka 50 hz with ics =100% icu & thermal magnetic adjustable typeincluding spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 01 no. c. interlocking ( iii ) . electrical interlocking & mech. 0 2 no. all as approved by lt panel oem. 33 d. outgoing : ( iv ) mccb 200 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 02 nos. ( v ) mccb 100 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 04 no. ( vi ) mccb 63 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 03 nos. ( vii ) led indicators r / y / b 240 v ac 06 nos per incoming and outgoing feeders. ( viii ) multifunction meter with accuracy class 1.0, flush mounting 96 x 96 mm, ct / pt site programmable for measurement of v, a, pf, kw, kva, load hours including suitable size cts ( set of 3 ) 01 no. ( 01 no. for incoming feeder ) ( ix ) single function 3 phase led voltmeter with accuracy class 1.0, flush mounting 96 x 96 mm, input voltage measurement range 50 520 vac ( p p ) , ct / pt site programmable including suitable size cts ( set of 3 ) 06 nos. ( outgoing feeders ) ( x ) single function 3 phase led ammeter with accuracy class 1.0, flush mounting 96 x 96 mm, input voltage measurement range 50 520 vac ( p p ) , ct / pt site programmable including suitable size cts ( set of 3 ) 06 nos. ( outgoing feeders ) ( xii ) control wiring with suitable size pvc insulated single core copper conductor cable for led lamps, mfms, etc. 34 all as peritem 32 above but panel with following components a. incoming ( ii ) mccb 400 amps , 415 v 4 pole 36 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 02 no. b. bus coupler ( ii ) mccb 400 amps , 415 v 4 pole 36 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 01 no. c. interlocking ( iii ) . electrical interlocking & mech. 02 no. all as approved by oem. 35 d. outgoing ( iv ) mccb 250 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 02 nos. ( v ) mccb 160 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 01 no. ( vi ) mccb 63 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 01 nos. ( vii ) led indicators r / y / b 240 v ac 30 nos 03 nos per incoming and outgoing feeders. ( viii ) multifunction meter with accuracy class 1.0, flush mounting 96 x 96 mm, ct / pt site programmable for measurement of v, a, pf, kw, kva, load hours including suitable size cts ( set of 3 ) 01 no. ( 01 no. for incoming feeder ) ( ix ) single function 3 phase led voltmeter with accuracy class 1.0, flush mounting 96 x 96 mm, input voltage measurement range 50 520 vac ( p p ) , ct / pt site programmable including suitable size cts ( set of 3 ) 06 nos. ( outgoing feeders ) ( x ) single function 3 phase led ammeter with accuracy class 1.0, flush mounting 96 x 96 mm, input voltage measurement range 50 520 vac ( p p ) , ct / pt site programmable including suitable size cts ( set of 3 ) 06 nos. ( outgoing feeders ) ( xi ) mcb sp c series 10ka 60 32 amps as protection for led lamps ( 01 no. each for set of 03 nos. led lamps, multifunction and single function meters ) and multifunction meter 30 nos. 36 all as per item 32 above but panel without bus couplerbut panel with following components ( i ) mccb 250 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 01 no. incoming ( ii ) mccb 100 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable type including spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 03 nos. outgoing ( iii ) mccb 63 amps , 415 v 4 pole 25 ka 50 hz with ics =100% icu & thermal magnetic adjustable typeincluding spreader terminals set of 04 and direct rotary handle 01no as per oem specifications and model 02 no 37 outgoing ( iv ) led indicators r / y / b 240 v ac 18 nos. 03 nos per incoming and outgoing feeders ( v ) multifunction meter with accuracy class 1.0, flush mounting 96 x 96 mm, ct / pt site programmable for measurement of v, a, pf, kw, kva, load hours including suitable size cts ( set of 3 ) 01 no. ( for incoming ) . ( vi ) single function 3 phase led voltmeter with accuracy class 1.0, flush mounting 96 x 96 mm, input voltage measurement range 50 520 vac ( p p ) , ct / pt site programmable including suitable size cts ( set of 3 ) 04 nos. ( outgoing feeders ) ( vii ) single function 3 phase led ammeter with accuracy class 1.0, flush mounting 96 x 96 mm, input voltage measurement range 50 520 vac ( p p ) , ct / pt site programmable including suitable size cts ( set of 3 ) 04 nos. ( outgoing feeders ) ( viii ) mcb sp c series 10ka 60 32 amps as protection for led lamps ( 01 no. each for set of 03 nos. led lamps, multifunction and single function meters ) and multifunction meter 18 nos. ( ix ) control wiring with suitable size pvc insulated single core copper conductor cable for led lamps, mfms, etc. 38 material & labour for painting to electric control panel of e / m installations by cleaning the existing old paint with the help of spray and mechanical tools such as wire brush, scraper and sand paper from the surface of panel and painting the prepared surface with two coat of synthatic enamel paint of approved shade over a coat of red oxide primer complete all as specified abd specified. 39 restringing and fixingacsr conductor reinforced of any size to proper sag incl binding on insulator all as specified and as directed by engr in charge 40 cutting & trimming of tree branches any girth and sizearound overhead lines to a clear distance 1.5 mtr both sides of overhead line with in a 25 to 40 mtrs span gap of ht / lt lines including clearing the site all as specified and directed by the engr in charge. 41 material & labour for stay assembly complete with accessories as shown in electric plate no.i including loop type insulator, stay clamps etc complete all as specified & directed with diameter of stay 20 mm of stay rod complete all as specified & directed. 42 supply & fix power contactor 3 pole, type ml 3, with 2 no + 2 nc aux contacts with standard coil voltage 415 volts, rating 40 / 63 amp as per cat no. 90721 of m / s l & t or eqivalent in m / s siemens / schneider / abb as existing including testing connecting commissioning complete all as specified and directed. 43 dismantling and disconnecting unservicable timer, supply and fixing in replacement of three phase load of 5 kw for automatic street light control switch using infrared sensor based natural switch for automatic switching of street lights. nature switch operation should be based on natural light lux* level, required illuminance level for switching on is = 30 lux and for switching off = 10 lux. the sensor should have part night operation facility of minimum 4 hrs. to max. 12 hrs. the sensor along with 3 nos suitable contactor each 20 to 25 amp current rating incoming mcbs & outgoing mcbs of 20 25 amps ( 03 nos ) and circuit should also have provision for manual operation ( i.e. sensor bye pass option ) . circuit should be multistrand frlsh min size ofminmum 10 sq.mm copper cable. selection operation should be enclosed in a pole / wall mounted enclosure made of rust proof, electric shock proof termite proof and fr grade special mounting compound ( sintex made smc junction box ) confirming to ip 54 including taking down old unserviceable timer any type complete all as specified and as directed by engineer in charge 44 m&l for application of two coats of aluminium / metal black paint as existing on steel tubular / rail pole of 9 / 11 / 13 / 15 m long externally after removal of old paint, rust, dust, oil, grease or any other foreign deposits by paint removers or burning off by blow lamps, cleaning with scrapers and chemicals for removal of rust for any number of coats of any width or girth including. numbering of poles in black base & white letters paint and including painting five no. strips of 30 cm on bottom of pole with black and red colour paint alternatelyall as specified and directed by engr in charge. 45 supply, install factory made outdoor type crca sheet steel duly phosphatized and powder coated with 7 tank process made enclosure three phase 50 hz ac timer based wall mounted feeder pillar box having degree of protection ip 32 & 54 with 24 hour programmable astronomical time switch, auto / manual selector switch 01 no., door locking by panel lock and provision for pad lock, pre wired ready to use, liberal termination space, louvers provided on both sides for proper heat dissipation, suitable three phase 63 amps power contactor 01 no., suitable mcb sp 01 no. and 63 amps tpn 01 no. as incoming incld. setting of the astronomical time switch, testing and commissioning of the panel complete all as per directions and specifications of engineer in charge and all as per havells make, cat no. ihxts09120. 46 supply, installing, testing and commissioning factory madelt feeder pillar box outdoor type platform mounted, suitable for 415 volts 3 phase 4 wire, 50 hz ac supply system fixed at a hight of 2 ft from ground lavel all as specified and directed having bus bar installed on dmc / epoxy insulators. the panel shall be dust and vermin proof, ip 65 class protection and made of 3.15 mm crca ms sheet with frontopeningtype with double door shutter and locking arrangement ( including provn oflock with 2 keys ) , powder coated finish ( over a coat of red oxide ) , primer on outside and two coats of red oxide primer on inside surfacewith tpn aluminium bus bar of rating not less than 200amps on suitable foundation. 47 supplying and fixing 1100 volts grade heavy duty cable pvc insulated aluminium conductor, served with inner sheathing of pvc tape and overall pvc sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of 10 sqmm standard conductor complete all as specified and directed by engr in charge. 48 all as per ser item no 44 here in before but size 16 sqmm standard conductor complete all as specified and directed by engr in charge. 49 supply & fix of lt aluminium thimble of size 630mm as specified and as directed by engr in charge. 50 supply & fix of lt aluminium thimble of size 300mm as specified and as directed by engr in charge. 51 supply & fix of lt aluminium thimble of size 240mm as specified and as directed by engr in charge. 52 supply & fix of lt aluminium thimble of size 120mm as specified and as directed by engr in charge. 53 supply & fix of lt aluminium thimble of size 95mm as specified and as directed by engr in charge. 54 supply & fix of lt aluminium thimble of size 70 mm as specified and as directed by engr in charge. 55 supply & fix of lt aluminium thimble of size 35 50 mm as specified and as directed by engr in charge. 56 material & labour for pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 50mm height, 65mm dia for 1100 volts grade 57 material & labour for pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, , 100mm height, 65mm dia for 1100 volts grade 58 material & labour for shackle type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 50mm height, 65mm dia for 1100 volts grade 59 material & labour for cement concrete 1:4:8 type d 2 using 40mm graded crushed stone aggregate in foundation filling & mass concrete for poles / struts / stays assembly complete all as specified and directed by engr in charge. 60 material & labour for cement concrete 1:2:4 type b 1 using 20mm graded crushed stone aggregate in coping pedestal to poles including provision of necessary frame work finishing the expossed surface even and smooth complete all as specified and directed by engr in charge....

Due Date : October 02, 2023

Tender Value : ₹ Ref. Documents

8

Military Engineer Services - Punjab

39230699 provision of buildings for mil dental centre ( type ‘c’ ) at old ge amritsar; 1 lumpsum / pre priced provisional schedules of works 2 schedule a part i building works : lump sum price worked out by the contractor for building of mdc type c complete all as specified and shown on drgs as listed in sch a part i brought forward from srl page no 24. 3 schedule ‘a’ part ii site clearance, excavaton and earth work : lump sum price worked out by the contractor for site clearance, excavation and earth work complete all as specified and shown on drgs as listed in sch a part i brought forward from srl page no 25. 4 schedule a part iii “parking sheds” : lump sum price worked out by the contractor for “parking sheds” as listed in schedule a part iii brought forward from serial page no. 27 complete all as specified and shown on drgs. 5 schedule a part iv “fire fighting” : lump sum price worked out by the contractor for “fire fighting” as listed in schedule a part iv brought forward from serial page no. 29 complete all as specified and shown on drgs. 6 schedule a part v “sewage disposal” : lump sum price worked out by the contractor for “sewage disposal” as listed in schedule a part v brought forward from serial page no. 31 complete all as specified and shown on drgs. 7 schedule a part vi “area drainage” : lump sum price worked out by the contractor for “area drainage” as listed in schedule a part vi brought forward from serial page no. 32 complete all as specified and shown on drgs. 8 schedule a part vii “chain link fencing” : lump sum price worked out by the contractor for “chain link fencing” as listed in schedule a part vii brought forward from serial page no. 35 complete all as specified and shown on drgs. 9 schedule a part viii “external water supply” : lump sum price worked out by the contractor for “external water supply” as listed in schedule a part viii brought forward from serial page no. 37 complete all as specified and shown on drgs. 10 schedule a part ix “external electric supply” : lump sum price worked out by the contractor for “external electric supply” as listed in schedule a part ix brought forward from serial page no. 38 complete all as specified and shown on drgs. 11 schedule a part x “pvc conduit” : lump sum price worked out by the contractor for “pvc conduit” as listed in schedule a part x brought forward from serial page no. 39 complete all as specified and shown on drgs. 12 schedule a part xi “earthing equipment” : lump sum price worked out by the contractor for “earthing equipment” as listed in schedule a part xi brought forward from serial page no. 41 complete all as specified and shown on drgs. 13 schedule a part xii “dg sets” : lump sum price worked out by the contractor for “dg sets”as listed in schedule a part xii brought forward from serial page no. 43 complete all as specified and shown on drgs. 14 schedule a part xiii “solar water heater” : lump sum price worked out by the contractor for “solar water heater” as listed in schedule a part xiii brought forward from serial page no. 45 complete all as specified and shown on drgs. 15 schedule a part xiv “cooling appliances” : lump sum price worked out by the contractor for “cooling appliances” as listed in schedule a part xiv brought forward from serial page no. 46 complete all as specified and shown on drgs. 16 schedule a part xv ( miscellaneous items ) 17 s&f for 15 mm bib taps, with sensor system cast copper alloy fancy type chromium plated with flange screwed down screwed for iron pipe of 15mm bore.make jaquar or equivalent approved by ge. ( cat part no. snr chr 35019pm ) complete all as specified and directed. 18 supplying laying in trenches jointing and testing dwcpe pipes ( sn8 ) 200 od / 175 od mm marked all as specified and directed. ( excavation and earthwork shall be measured and paid seprately under appropriate item of sch a ) 19 s&ffor pvc coated galvanized iron chain link fencing, made of gi wire dia not less than 3 mm, and minimum dia 4.5 mm after pvc coating, having any mesh size ( mesh size as approved by ge ) including line wire, any type of standards, rails, straining bolts, etc including provission of binding wire, fixed as knuckled type complete all as specified and directed by the engineer in charge. 20 surface excavation not exceeding30 cm deep and averaging 15cm deep and getting outin soft / loose soil, separate the roots / grass and good earth by sieving with suitable sieve size , stacking of good earth & mixed with suitablemanure of ratio 5:1 including supply of manure, screened through sieve of 1.5 designation 4.75 mm and spreading the mixture of good earth & manure , applying suitable pesticides , watering to a depth of15cms, including removal of roots / grass out of site complete all as specified and directed by the garrison engineer 21 material and labourfor developing lawn by layingand dibbling of grass stealers ofdoob grass planting , roofing etc complete as approved and as directed by the garrison engineer. 22 supply & labour for developing and planting of bottle palmtree of height not less 4 feet including exavation in post holes of size 60 cm x 60 cm x 60 cm or according to the plant size and plant the trees straight inside the pit and fill up the pit with the earth along with inorganic fertilise manure ( compost ) in the proportion ( 3:1 ) and remove and spread the surplus excavated soil complete all as specified and as directed by the engineer in charge. 23 supply & labour for developing and planting of gulmohartree ( delonix regia ) of height not less 2 feet including exavation in post holes of size 60 cm x 60 cm x 60 cm or according to the plant size and plant the trees straight inside the pit and fill up the pit with the earth along with inorganic fertilise manure ( compost ) in the proportion ( 3:1 ) and remove and spread the surplus excavated soil complete all as specified and as directed by the engineer in charge. 24 supply & labour for developing and planting of amaltastree ( cassia fistula ) of height not less 2 feet including exavation in post holes of size 60 cm x 60 cm x 60 cm or according to the plant size and plant the trees straight inside the pit and fill up the pit with the earth along with inorganic fertilise manure ( compost ) in the proportion ( 3:1 ) and remove and spread the surplus excavated soil complete all as specified and as directed by the engineer in charge. 25 supply & labour for developing and planting of neem tree ( azadirachta indica ) of height not less 3 feet including exavation in post holes of size 90 cm x 90 cm x 90 cm or according to the plant size and plant the trees straight inside the pit and fill up the pit with the earth along with inorganic fertilise manure ( compost ) in the proportion ( 3:1 ) and remove and spread the surplus excavated soil complete all as specified and as directed by the engineer in charge. 26 material & labour for developing and planting hedgesincluding 60cm wide laying and dibbling of soil rows and watering , including excavation post holes for plant as required , returning filling with earth in necessary watering and finally fine dressing, levelling etc and completeincluding stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling , the distance between plants not exceeding 90cms complete all as specified and as directed by the engineer in charge. the following species for hedges shall be used: ( a ) ixora ( b ) hibiscus ( c ) goudi choudi ( d ) plumbago ( e ) nerium oleander ( f ) tecoma capsensis eranthemum note: the cost of earth, royality, manure & item transportation is deemed to be inlcuded in the unit rate quoted. 27 m&l for drilling and tapping ci / di water mains of 100 / 150 mm dia ( in position ) for branch connections of the internal dia 40 mm include for turning water off and on and draining and refilling complete all as directed and specified by engineer in charge. 28 material and labour for construction of brick masonary pits ( 230mm thick wall ) of 900x600x1000mm internal dimension ( bottom pcc floor of the pit should be minimum 30cms below the bottom surface of sluice valve flange to provide sufficient working space ) , bottom floor of the pit be constructed in pcc ( 1:4:8 ) type d2 using 15cms thick with 20mm stone aggregate for foundation, brick wall with sub class b bricks built in cm 1:6, inner and exposed surfaces and bottom floor of the pit should be plastered in cement mortar ( 1:4 ) 15mm thick, pcc 1:2:4 type b1 using 20mm graded stone aggregate for coping. the sluice valve and other fittings should be housed in center of the pit. the vertices of the pit should in right angle and chamfered. the top cover of the pit will be made out of ms sheet 3mm thick with angle iron frame made out of ms angle 50mmx50mmx6mm with galvanized steel hinges two nos. and locking arrangements duly painted with two coats of water resistant synthetic enameled paint over one coat of red oxide including necessary excavation and earth work in any type of soil complete all as shown in drg no. cejz / td 1060 sheet 1 / 3 to 3 / 3. 29 shifting of transformer 200 / 250 kva from extg location to mdc ( within 1000 mtrs ) outdoor type 11000 / 433 volts, 3 phase 4 wire, 50 cycle naturally oil cooled type suitable for outdoor installation on plinth of mdc sub stn complete all as specified and directed by engr in charge.note: ( a ) rate shall be inclusive oftransformer plinth of size 1.5x1.5x1.5 mtr ( b ) the safe transformer lifting from extg location, shifting and placing on new plinth is contractors responsibilty and any damage to transformer in these activities will be entire contractors responsibilty and contract has to make good the losses. ( c ) the transformer oil will be filtered by the contractor and topping of the same will be done by the contractor before energysing the transformer, rate quoted shall be inclusive of the same. ( d ) the existing transformer of capacity 160 kva will be removed from pole and will be deposited to thimayya power house. 30 supply and fixing double compression copper gland for fixing armoured cables of size 95 sqmm 3 core nominal cross sectional area complete all as directed 31 all as per ser item no. 2.14 above but cross sectional area 120 sqmm 3½ core complete all as specified and directed. 32 all as per ser item no. 2.14 above but cross sectional area 70 sqmm 3½ core complete all as specified and directed. 33 supply & laying double wall corrugated ( dwc ) high density poly ethylene ( hdpe ) of size 100mm dia including all necessary fittings, pn 4 rating, pressure 6 kgf / cm², conforming to is 16205 ( part 24 ) with high ring stiffness & cursh resistance capacity, etc., laid in trench for protection of submersible flat cable complete all as directed. 34 supply, install, testing and commissioning of lt feeder pillar distribution panel board ( kiosk ) cpriapproved, outdoor type, double door ( front & rear openable with gasket arround doors ) , weather / vermin proof of ip 54, made out of 3.15mm thick crca mild steel ( certificate from manufacturer will be necessary for quality aasurance and guarantee ) as per is:8623 of suitable size and medium channel 75mm base mounting frame of50mm x 50mm x 5mm, with stainless steel hinges, door handles ( front & rear ) , factory assembled cubicle pattern modular and compartmentalized construction, floor mounted free standing type, 3 phase and neutral 500 amps current carrying capacity aluminium busbar with epoxy insulated coating with colour sleeves and including incoming acb and outgoing mccbs, cable galleries inter connecting busbar connection / linkage with countersunk holes at bottom for base mounting brackets and sheet steel gland plates for cable entry complete with the following accessories and suitable for housing one incoming mccb and outgoing mccbs of capacity as below complete and mounting the panel board on suitable foundation with pcc ( 1:3:6 ) , bedding upto a height 45cm above ground level, duly grouted with bolts, nuts & washers by using angle iron frame of size 50mm x 50mm x 6mm including prewired with suitable size pvc insulated copper conductor cable not less than 2.5 sqmm complete all as specified and directed with the following accessories: 35 note: panel drg will be got approved from ge by the contractor before manufacturing. ( a ) aluminium busbar duly colour code ( 04 nos. ) 1 set ( b ) mccb 4 pole 320 amps 36ka at 415 v, adjustable thermal magnetic settings 01 no. ( incoming ) ( c ) mccb 4 pole 250 amps 50ka at 415 v, adjustable thermal magnetic settings 01 no. ( outgoing for mdc ) ( d ) mccb 4 pole 100 amps 25ka at 415 v, adjustable thermal magnetic settings 01 no. ( spare ) ( e ) ct of ratio suitable size isi marked 1 set ( three each ) ( f ) digital voltmeter with selector switch 0 to 500 volts 1 no. ( g ) digital ammeter with selector switch and cts 0 to 500 amps 01 no. ( h ) mf meter 0 1 no. ( j ) led type phase indicator lamps ( r 36 ditto all as per item no. 2.18 above but consisting of the following: ( a ) aluminium busbar duly colour code ( 04 nos. ) 1 set ( b ) mccb 4 pole 250 amps 36ka at 415 v, adjustable thermal magnetic settings 01 no. ( incoming ) ( c ) mccb 4 pole 80 amps25ka at 415 v, adjustable thermal magnetic settings 02 nos. ( outgoing ) ( d ) mccb 4 pole 63 amps 25ka at 415 v, adjustable thermal magnetic settings 04 nos. ( outgoing & spare ) ( e ) ct of ratio suitable size isi marked 1 set ( three each ) ( f ) digital voltmeter with selector switch 0 to 500 volts 1 no. ( g ) digital ammeter with selector switch and cts 0 to 500 amps 01 no. ( h ) mf meter 0 1 no. ( j ) led type phase indicator lamps ( r 37 frp fencing to the transformer of size 7.5 mtrs x7.5 mtrs x2 mtr in height complete all as specified and directed. 38 supply and fixing double compression copper gland for fixing armoured cables of size 120 sqmm 3½ core nominal cross sectional area complete all as directed 39 supply & laying double wall corrugated ( dwc ) high density poly ethylene ( hdpe ) of size 100mm dia including all necessary fittings, pn 4 rating, pressure 6 kgf / cm², conforming to is 16205 ( part 24 ) with high ring stiffness & cursh resistance capacity, etc., laid in trench for protection of submersible flat cable complete all as directed. 40 supply, install, connect, test and commissioning of silent diesel engine driven with amf panel generating set, water cooled type, bhp 156 @ 1500 rpm, 6 cylinder, acoustic proof, comprising diesle engine as per is:10001 / 10002, alternator as per is: 13364, ac, 415 volts, 50 hz, 3 phase 4 wire, 125 kva capacity coupled to engine, complete with foundation ( as per oem design ) , installed / fixed on common base plate with anti vibration pads / friction pads and comprising: a ) battery charger of suitable capacity for charging the batteries suitable for operation on ac 1 f, 230 volts 50 hzb ) battery of suitable capacity and nos with copper flexible pvc insulated cables and terminals lugs.c ) initial filing of engine oil to te required level / standard.d ) fuel tank capacity not less 8 working hours fuel with initial filling of diesel of required quantity for testing the dg sete ) digital type metre for reading volts, amps, frequency, rpm, hours run, kwh etc., f ) engine safety unit indicator for supply on, low lop, battery removed, high tempareture, fuse open, v belt failed, charge, auxiliary trip / emergency stop, stop solenoid on etc., g ) pressure gauge 0 10 bar, tempareture gauge, ammeter 50 0 50, indicator lamp for set on, load on, start switch, key type on / off control.note: ( a ) electrical load test on alternator shall be carried out at site and all arrangement to carry out the load test as per particular specification shall be made by the contractor. ( b ) diesel oil for testing of dg set shall be deemed to be included in the rate quoted. ( c ) training to department staff shall be given. ( d ) aquostic proof enclosure shall conform to central pollution control board ( cpcb ) norms and shall be carried out by authorised manufacturers and certificate to this effect shall be submitted. ( e ) operation and maintenance manual and test certificate for engine, alternator and acoustic proof enclosure. ( f ) rate quoted sall be deemed to have been inclusive of above 41 supply, install, testing and commissioning of refrigerator, electric driven, single phase, 230 volts ac, 50 hz, frost free, double door, copper coil material, energy efficient bee 5 ( five ) star rated of capacity more that 195 ltrs upto 310 litres as directed by engr in charge including refrigerator mounting stand complete all as specified and directed 42 supply and install voltage stabilizer for automatic operation with digital voltmeter to monitor in / out voltage with time delay and bypass switch, single phase, thermal overload protection, low & high voltage cut off protection, led indication, ic controlled, naturally air cooled indoor type and design for input variation between 170 volts to 250 volts with output output voltage stabilized at 230v with accuracy of + 2.5% and of capacity 2 kva complete all as specified and directed 43 all as per ser item no. 2.26 above but of capacity 5 kva...

Due Date : October 21, 2023

Tender Value : ₹ 1.29 Crore

9

Micro Small And Medium Enterprises - Punjab

38816847 bids are invited for lt panel and other electrical works supply and installation of lt panel in the central block electrical power distribution room , supply and installation of lt distibution panel for production shop machines power supply , supply and installation of lt panel for training workshop machines distribution power supply , upgradation of existing fan and lighting power suppply distribution panels of ctr administration building, traiing and production workshop and central block training lab , supply and installation of lt panel in gen set room for maintenance, ppc, main store including raw material store power hacksaw, welding work shop , supply and installation of lt distibution panel in gen set room for generator and main incoming power supply distribution total quantity : 21...

Due Date : August 04, 2023

Tender Value : ₹ 18 Lakhs

10

Indian Army - Punjab

36270101 bids are invited for kva for comn det ups 10 kva , smps 48 v , stabilizer 30 kva , distribution panel , 20 sqmm cable , 10 sqmm copper cable , dc distribution pannel , earthing , installation charge provn of 04 x 48v dc smps 150 ahc and 04 x ups 10 total quantity : 36...

Due Date : April 29, 2023

Tender Value : ₹ Ref. Documents

11

Railtel Corporation Of India Limited - Punjab

35723196 procurement of electrical ( general ) items in connection with up gradation of signalling from standard i to standard ii ( r ) with electronic interlocking ( ei ) at 5 stations ( i.e. verka, kathunangal, jaintipura, batala, chhina ) on asr ptk section of firozpur division.procurement of electrical ( general ) items in connection with up gradation of signalling from standard i to standard ii ( r ) with electronic interlocking ( ei ) at 5 stations ( i.e. verka, kathunangal, jaintipura, batala, chhina ) on asr ptk section of firozpur division., supply of active lightening arrestor of class a for building protection as per standard nfc 17 102. it shall work on early streamer emission principle and shall be made of stainless steel with a t of 60 micro seconds. a non resettable type counter should also be supplied to count the number of lighting occurrences. it also includes supply of electrolytic copper tape of 25mm x 2mm of better to connecting class a devices to the earth pit. this includes installation, testing and commissioning of class a device on top of the building. this device should be installed at suitable height on top of the building using a gi mask as per the instruction of rcil engineer at site. the device should be connected to earth pit using a copper tape of 25mm x 2mm or better. this copper tape should be run firmly only the side of mask with the help of spacers. it shall also be ensured that the down conductor shall not touch the building throughout. the down conductor shall be connected to the earth electrode using exothermic welding. a counter shall be installed at appropriate space to count the number of occurrences. all the accessories like spares, welding material etc. required for installation shall be arranged by the contractor. ( inspection by rdso ) . [ warranty period: 12 months after the date of delivery ] , supply of change over switch 200 amp. 3 phase, 415v ac, 50hz ( side handle ) four pole, make havels ihcffe 200 or superior. ( inspection by , supply of 1.1 kv grade lt xl / pe . insulated armored aluminum conductor cable, making good the damages end termination with aluminum crimping socket / plugs. provision of cable route markers etc. as required as per technical specification no. is 7098. size ( 2x70 sq. mm ) . ( inspection by , laying of 1.1 kv grade lt xl / pe .insulated armored aluminum conductor cable, making good the damages end termination with aluminum crimping socket / plugs. provision of cable route markers etc. as required as per technical specification. size ( 2x70 sq. mm ) . [ warranty period: 12 months after the date of delivery ] , supply of control and distribution panel for 10 kva auxiliary transformer for color light signaling supply in 25kv / ac traction system as per rdso technical specification no tl / spc / psi / cls / 0020 ( 12 / 02 with a&c slips no 1 to 4 latest connection as required. ( inspection by , erection testing & commissioning of control and distribution panel for 10 kva auxiliary transformer for color light signaling supply in 25kv / ac traction system as per rdso technical specification no tl / spc / psi / cls / 0020 ( 12 / 02 with a&c slips no 1 to 4 latest connection as required. [ warranty period: 12 months after the date of delivery ] ...

Due Date : February 06, 2023

Tender Value : ₹ Ref. Documents

12

Military Engineer Services - Punjab

35536155 tender for certain repair to safety equipment and allied works at elect sub station at nams supply install, testing and commissioning lt distribution panel, cubicle type, ip 56, outdoor type, factory fabricated made out of 3 mm thick crca sheet outer & 2mm thick crca sheet inner of suitable size to accommodate all accessories / fittings, compartmentalized in costruction to accommodate the incoming mccb and tpn bus bars and outgoing feeders. the tpn busbars of suitable size dully insulated with colour coded heat shrinkable sleeve and shall be mounted on dmc / epoxy insulator . the extension links shall be supported on dmc / epoxy insulators having provision for termination of incoming and outgoing cables. all extension links / interconnection shall colour coded sleeves. the cubicle shall have frame work, bottom & 90 cm long four legsof size 50 x 50 x 6 mm angle iron, grouted in pcc 1:2:4, 15 cm thick in foundation, brick ( sub class b ) work in cm 1:6 on exposed surfaces and 100mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel 30cm below ground level and 60 cm above ground level, rate for platform shall be included in the quoted rate, all as directed by eng in charge.a detacheablegland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be powder coated finish with ral 7032 siemens gray structure after seven tank phosphating treatment, front & back opening type, andfixing 2 nos.danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to lt panel with voltage and danger indicated in hindi and english, with double door shutter and shall have louvers and airvent gasket for natural flow of air, neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following ( note: ltpanel board should be as per is / iec 61439 i: 2011 &is / iec 61439 2 : 2011, type test certificates for shot circuit test, temperature rise test, di electricproperty test and degree of protection ip 65 at minimum 4000 amps with breaking capacity not less than 65ka. ( the contractor should submit all certificates before executing the job. ) ( location 66 kv sub stn ) make of panel boards: legrand, l&t, shalabh, schneider &abb, make of mccb : havells / schneider / siemensaccessories: incomming: a ) busbar4 pole, aluminum, 300 amps 01 set ( b ) mccb 200 amp 4 pole, 36ka, with adjustable thermal setting alongwith spreader terminals & roh 01no ( c ) led type phase indicator lamp ( ryb ) = 03 nosd ) ammeter digital type, ct operated 0 500a range, make: secure / l&t ( with selector switch and ct 200 / 5 amp ) 01 sete ) volt meter digital type 0 500 v range, make: secure / l&t ( with selector switch ) 01 setoutgoing : ( a ) mccb 63 amp 4 pole, 16 / 18 ka, with adjustable thermal setting alongwith spreader terminals & roh 01no. ( b ) mcb 32 amp dp, 10ka, c series 09 nos.note: ( i ) the panel make should be cpri approved. ( ii ) before placing the order the panel drawing should be approved by garrison engineer. ( iii ) platform for the feeder pillar board with pcc 1:2:4 15 cm thick in foundation, brick ( sub class b ) work incm 1:6 , rendering 1:6 on exposed surfaces and 100 mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . the platform shall be of 40 cm below ground level and 60cm height above ground level . rate forplatform shall be included in the quoted rate. 2 supply install, testing and commissioning lt distribution panel, cubicle type, ip 56, outdoor type, factory fabricated made out of 3 mm thick crca sheet outer & 2mm thick crca sheet inner of suitable size to accommodate all accessories / fittings, compartmentalized in costruction to accommodate the incoming mccb and tpn bus bars and outgoing feeders. the tpn busbars of suitable size dully insulated with colour coded heat shrinkable sleeve and shall be mounted on dmc / epoxy insulator . the extension links shall be supported on dmc / epoxy insulators having provision for termination of incoming and outgoing cables. all extension links / interconnection shall colour coded sleeves. the cubicle shall have frame work, bottom & 90 cm long four legsof size 50 x 50 x 6 mm angle iron, grouted in pcc 1:2:4, 15 cm thick in foundation, brick ( sub class b ) work in cm 1:6 on exposed surfaces and 100mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel 30cm below ground level and 60 cm above ground level, rate for platform shall be included in the quoted rate, all as directed by eng in charge.a detacheablegland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be powder coated finish with ral 7032 siemens gray structure after seven tank phosphating treatment, front & back opening type, andfixing 2 nos.danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to lt panel with voltage and danger indicated in hindi and english, with double door shutter and shall have louvers and airvent gasket for natural flow of air, neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following ( note: ltpanel board should be as per is / iec 61439 i: 2011 &is / iec 61439 2 : 2011, type test certificates for shot circuit test, temperature rise test, di electricproperty test and degree of protection ip 65 at minimum 4000 amps with breaking capacity not less than 65ka. ( the contractor should submit all certificates before executing the job. ) ( location khetarpal jco & ors qtrs ) make of panel boards: legrand, l&t, shalabh, schneider &abbmake of mccb : havells / schneider / siemensincomming: a ) busbar4 pole, aluminum, 800 amps 01 set ( b ) mccb 500 amp 4 pole, 36ka, with adjustable thermal setting alongwith spreader terminals & roh 01no. ( c ) led type phase indicator lamp ( ryb ) = 03 nosd ) ammeter digital type, ct operated 0 500a range, make: secure / l&t ( with selector switch and ct 500 / 5 amp ) 01 sete ) volt meter digital type 0 500 v range, make: secure / l&t ( with selector switch ) 01 setoutgoing : ( a ) mccb 300 amp 4 pole, 36ka, with adjustable thermal setting alongwith spreader terminals & roh 02nos. ( b ) mccb 100 amp 4 pole, 16 / 18 ka, , with adjustable thermal setting alongwith spreader terminals & roh 01no. ( b ) mccb 63 amp 4 pole, 16 / 18 ka, , with adjustable thermal setting alongwith spreader terminals & roh 01no.note: ( i ) the panel make should be cpri approved. ( ii ) before placing the order the panel drawing should be approved by garrison engineer. ( iii ) platform for the feeder pillar board with pcc 1:2:4 15 cm thick in foundation, brick ( sub class b ) work incm 1:6 , rendering 1:6 on exposed surfaces and 100 mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . the platform shall be of 40 cm below ground level and 60cm height above ground level . rate forplatform shall be included in the quoted rate. 3 supply install, testing and commissioning lt distribution panel, cubicle type, ip 56, outdoor type, factory fabricated made out of 3 mm thick crca sheet outer & 2mm thick crca sheet inner of suitable size to accommodate all accessories / fittings, compartmentalized in costruction to accommodate the incoming mccb and tpn bus bars and outgoing feeders. the tpn busbars of suitable size dully insulated with colour coded heat shrinkable sleeve and shall be mounted on dmc / epoxy insulator . the extension links shall be supported on dmc / epoxy insulators having provision for termination of incoming and outgoing cables. all extension links / interconnection shall colour coded sleeves. the cubicle shall have frame work, bottom & 90 cm long four legsof size 50 x 50 x 6 mm angle iron, grouted in pcc 1:2:4, 15 cm thick in foundation, brick ( sub class b ) work in cm 1:6 on exposed surfaces and 100mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel 30cm below ground level and 60 cm above ground level, rate for platform shall be included in the quoted rate, all as directed by eng in charge.a detacheablegland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be powder coated finish with ral 7032 siemens gray structure after seven tank phosphating treatment, front & back opening type, andfixing 2 nos.danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to lt panel with voltage and danger indicated in hindi and english, with double door shutter and shall have louvers and airvent gasket for natural flow of air, neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following ( note: ltpanel board should be as per is / iec 61439 i: 2011 &is / iec 61439 2 : 2011, type test certificates for shot circuit test, temperature rise test, di electricproperty test and degree of protection ip 65 at minimum 4000 amps with breaking capacity not less than 65ka. ( the contractor should submit all certificates before executing the job. ) ( location mech unit, khetarpaljco / ors qtrs ) make of panel boards: legrand, l&t, shalabh, schneider &abbmake of mccb : havells / schneider / siemensincomming: a ) busbar4 pole, aluminum, 800 amps 01 set ( b ) mccb 500 amp 4 pole, 36ka, with adjustable thermal setting alongwith spreader terminals & roh 01no. ( c ) led type phase indicator lamp ( ryb ) = 03 nosd ) ammeter digital type, ct operated 0 500a range, make: secure / l&t ( with selector switch and ct 500 / 5 amp ) 01 sete ) volt meter digital type 0 500 v range, make: secure / l&t ( with selector switch ) 01 setoutgoing : ( a ) mccb 250 amp 4 pole, 36ka, with adjustable thermal setting alongwith spreader terminals & roh 02nos. ( b ) mccb 100 amp 4 pole, 16 / 18 ka, with adjustable thermal setting alongwith spreader terminals & roh 03nos.note: ( i ) the panel make should be cpri approved. ( ii ) before placing the order the panel drawing should be approved by garrison engineer. ( iii ) platform for the feeder pillar board with pcc 1:2:4 15 cm thick in foundation, brick ( sub class b ) work incm 1:6 , rendering 1:6 on exposed surfaces and 100 mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . the platform shall be of 40 cm below ground level and 60cm height above ground level . rate forplatform shall be included in the quoted rate. 4 supply install, testing and commissioning lt distribution panel, cubicle type, ip 56, outdoor type, factory fabricated made out of 3 mm thick crca sheet outer & 2mm thick crca sheet inner of suitable size to accommodate all accessories / fittings, compartmentalized in costruction to accommodate the incoming mccb and tpn bus bars and outgoing feeders. the tpn busbars of suitable size dully insulated with colour coded heat shrinkable sleeve and shall be mounted on dmc / epoxy insulator . the extension links shall be supported on dmc / epoxy insulators having provision for termination of incoming and outgoing cables. all extension links / interconnection shall colour coded sleeves. the cubicle shall have frame work, bottom & 90 cm long four legsof size 50 x 50 x 6 mm angle iron, grouted in pcc 1:2:4, 15 cm thick in foundation, brick ( sub class b ) work in cm 1:6 on exposed surfaces and 100mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel 30cm below ground level and 60 cm above ground level, rate for platform shall be included in the quoted rate, all as directed by eng in charge.a detacheablegland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be powder coated finish with ral 7032 siemens gray structure after seven tank phosphating treatment, front & back opening type, andfixing 2 nos.danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to lt panel with voltage and danger indicated in hindi and english, with double door shutter and shall have louvers and airvent gasket for natural flow of air, neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following ( note: ltpanel board should be as per is / iec 61439 i: 2011 &is / iec 61439 2 : 2011, type test certificates for shot circuit test, temperature rise test, di electricproperty test and degree of protection ip 65 at minimum 4000 amps with breaking capacity not less than 65ka. ( the contractor should submit all certificates before executing the job. ) ( location kathania jcos & or md accn area ) make of panel boards: legrand, l&t, shalabh, schneider &abbmake of mccb : havells / schneider / siemensincomming: a ) busbar4 pole, aluminum, 500 amps 01 set ( b ) mccb 315 amp 4 pole, 36ka, with adjustable thermal setting alongwith spreader terminals & roh 01no. ( c ) led type phase indicator lamp ( ryb ) = 03 nosd ) ammeter digital type, ct operated 0 500a range, make: secure / l&t ( with selector switch and ct 400 / 5 amp ) 01 sete ) volt meter digital type 0 500 v range, make: secure / l&t ( with selector switch ) 01 setoutgoing : ( a ) mccb 125 amp 4 pole, 25ka, with adjustable thermal setting with spreader terminals & roh 01 no. ( b ) mccb 100amp 4 pole, 16 / 18ka, with adjustable thermal setting with spreader terminals & roh 4nos. ( c ) led type phase indicator lamp ( ryb ) = 03 nosnote: ( i ) the panel make should be cpri approved. ( ii ) before placing the order the panel drawing should be approved by garrison engineer. ( iii ) platform for the feeder pillar board with pcc 1:2:4 15 cm thick in foundation, brick ( sub class b ) work incm 1:6 , rendering 1:6 on exposed surfaces and 100 mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . the platform shall be of 40 cm below ground level and 60cm height above ground level . rate forplatform shall be included in the quoted rate. 5 supply install, testing and commissioning lt distribution panel, cubicle type, ip 56, outdoor type, factory fabricated made out of 3 mm thick crca sheet outer & 2mm thick crca sheet inner of suitable size to accommodate all accessories / fittings, compartmentalized in costruction to accommodate the incoming mccb and tpn bus bars and outgoing feeders. the tpn busbars of suitable size dully insulated with colour coded heat shrinkable sleeve and shall be mounted on dmc / epoxy insulator . the extension links shall be supported on dmc / epoxy insulators having provision for termination of incoming and outgoing cables. all extension links / interconnection shall colour coded sleeves. the cubicle shall have frame work, bottom & 90 cm long four legsof size 50 x 50 x 6 mm angle iron, grouted in pcc 1:2:4, 15 cm thick in foundation, brick ( sub class b ) work in cm 1:6 on exposed surfaces and 100mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel 30cm below ground level and 60 cm above ground level, rate for platform shall be included in the quoted rate, all as directed by eng in charge.a detacheablegland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be powder coated finish with ral 7032 siemens gray structure after seven tank phosphating treatment, front & back opening type, andfixing 2 nos.danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to lt panel with voltage and danger indicated in hindi and english, with double door shutter and shall have louvers and airvent gasket for natural flow of air, neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following ( note: ltpanel board should be as per is / iec 61439 i: 2011 &is / iec 61439 2 : 2011, type test certificates for shot circuit test, temperature rise test, di electricproperty test and degree of protection ip 65 at minimum 4000 amps with breaking capacity not less than 65ka. ( the contractor should submit all certificates before executing the job. ) ( location red colony , noc i & noc iiarea ) make of panel boards: legrand, l&t, shalabh, schneider &abbmake of mccb : havells / schneider / siemensincomming: a ) busbar4 pole, aluminum, 500 amps 01 set ( b ) mccb 315 amp 4 pole, 36ka, with adjustable thermal setting alongwith spreader terminals & roh 01no. ( c ) led type phase indicator lamp ( ryb ) = 03 nosd ) ammeter digital type, ct operated 0 500a range, make: secure / l&t ( with selector switch and ct 400 / 5 amp ) 01 sete ) volt meter digital type 0 500 v range, make: secure / l&t ( with selector switch ) 01 setoutgoing : ( a ) mccb 160 amp 4 pole, 25ka, with adjustable thermal setting alongwith spreader terminals & roh 01no. ( b ) mccb 100 amp 4 pole, 16 / 18ka, with adjustable thermal setting alongwith spreader terminals & roh 03nos.note: ( i ) the panel make should be cpri approved. ( ii ) before placing the order the panel drawing should be approved by garrison engineer. ( iii ) platform for the feeder pillar board with pcc 1:2:4 15 cm thick in foundation, brick ( sub class b ) work incm 1:6 , rendering 1:6 on exposed surfaces and 100 mm thick pcc 1:3:6 type c1 using 20 mm graded stone aggregate as in padding on top and grouting legs of panel . the platform shall be of 40 cm below ground level and 60cm height above ground level . rate forplatform shall be included in the quoted rate. 6 supply laying in replacement & testing cable xlpe insulated screened pvc bedded, galvanised steel strip or wire armoured, electric power cable ( heavy duty ) lt 1100 voltgrade with stranded aluminium conductor of size185 sqmm 3.5 core complete all as specified and directed. 7 all as per item above here in before but of size 120 sqmm 3.5 core allas specified and directed by engr in charge. 8 all as peritem above here in before but of size 95 sqmm 3.5 core allas specified and directed by engr in charge. 9 all as per item above here in before but of size 70 sqmm 3.5 core allas specified and directed by engr in charge . 10 all as per item above here in before but of size 50 sqmm 3.5 core allas specified and directed by engr in charge. 11 supply, laying & fixing double wall corrugated ( dwc ) pipes of size 90mm outer dia and 76mm inner dia made of high density polythyline ( hdpe ) with all accessories i.e. all type of joints, sockets, elbows, bends and end caps etc.. allas specified and directed by engr in charge.of fwg sizes make; telerex / tirupati or e in c approved make 12 all as per item above here in before but of size 77mm outer dia and 63mm inner dia all as specified and directed 13 m&l for earthingcomplete with galvanized steel earth plate electrode600x600x6mm thick buried in ground vertical to a depth not less than 2.25 mtrs deep below ground level with top edge of plate not less than 1.5 mtr below normal ground level connected to galvanized gi strip of size 32 x 6 mm and 40 mm dia bore 7.5 mtr long light grade gi protection pipe for earth strip and gi watering pipe 40 mm dia medium grade from the top edge of earth plate fixed with deep cut onone end of pipe and fix from earth plate up to one feet above ground level of other end and plugged watering pipe at top with ms cap and grouted in pcc 1:2:4 of size 30 x 30 x 30 cm etc and 15 cm alternate layer of charcoal and salt around all sides of earth plate all as shown in electric plate no 3 of ssr part i of 2009 all as specified and directed. note : all joints either strip to strip of strip to earth plate are fixed with welded joints. 14 m&l for earthingcomplete with galvanized steel earth plate electrode600x600x6mm thick buried in ground vertical to a depth not less than 2.25 mtrs deep below ground level with top edge of plate not less than 1.5 mtr below normal ground level connected to galvanized gi wire of size 4 mm dia and 15 mm dia bore 7.5 mtr long light grade gi protection pipe for earth strip and gi watering pipe 40 mm dia medium grade from the top edge of earth plate fixed with deep cut onone end of pipe and fix from earth plate up to one feet above ground level of other end and plugged watering pipe at top with ms cap and grouted in pcc 1:2:4 of size 30 x 30 x 30 cm etc and 15 cm alternate layer of charcoal and salt around all sides of earth plate all as shown in electric plate no 3 of ssr part i of 2009 all as specified and directed. 15 m & lin replacement of acbcapacity 800 amp 50 ka 4 pole manual drawout type , microprocessor release auxilary switch 6 no+ 6nc with ct 100 / 5 , complete all as specified and as directed. ( location : khetarpal colony panelandred colony panel ) 16 m & lin replacement of mccb capacity 250 amp 36 ka 4 pole adjustable thermal megnate release type with preader and aluminium lugs all as fixed in existinglt panel all as specified and directed. make of mccb : havells / siemens / schneider ( location: red colony area & armd bde unit area, inf bde unit area oras urgent site requirement ) 17 m & lin replacement of mccb capacity 160 amp 36 ka 4 pole adjustable thermal megnate release type with preader and aluminium lugs all as fixed in existinglt panel all as specified and directed. make of mccb : havells / siemens / schneider 18 m & lin replacement of mccb capacity 100 amp , 16 ka , 3 pole adjustable thermal megnate release type with preader and aluminium lugs all as fixed in existinglt panel all as specified and directed. make of mccb : havells / siemens / schneider 19 m & lin replacement of mccb capacity 200 amp, 36ka, 4 pole adjustable thermal megnate release type with preader and aluminium lugs all as fixed in existinglt panel all as specified and directed. make of mccb : havells / siemens / schneider. 20 supply and laying gi steel tubing, 80mm bore, light grade with all fittings, laid in trenches / under roads / along pole / wallfor protection ofcable / gi wire / gi strip etc complete all as specified and directed. 21 excavation trenches notexceeding 1.5m wide& not exceeding 1.5m in depth for and getting out in any of soil all as specified and directed. 22 returning, filling including spreading, leveling, watering and well ramming in layers not exc 25 cm thick all as specified and directed. 23 removal of surplus excavated soil to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified 24 m & l in replacement of out door type aluminuam bus bar chamber feeder box of cap 300 amp , 3 phase, 4 strip, 415 volts of size 90 x 60 x 45 cm including incommer mccb 300 amp 4 pole with extended front operating rotary handle, made out of 3.15 mm crca sheet duly painted with two coats of synthetic enameld paint over a red oxide primer and fixed and supported with anlge iron size 40 x 40 x 6 mm grouted in pcc 1:2:4 upto 0.60 mtr high from ground level and 0.40 m below the ground level all as directed by engr in charge. note : contractor is responsible to produce drawing and take approval before placing order. make of mccb : havells / schneider / siemens 25 m & l in replacement of out door type aluminuam bus bar chamber feeder box of cap 300 amp , 3 phase, 4 strip , 415 volts of size 90 x 60 x 45 cm including incommer mccb 250 amp 4 pole withextended front operating rotary handle, made out of 3.15 mm crca sheet duly painted with two coats of synthetic enameld paint over a red oxide primer and fixed and supported with anlge iron size 40 x 40 x 6 mmgrouted in pcc 1:2:4 upto 0.60 mtr high from ground level and 0.40 m below the ground level all as directed by engr in charge. note : contractor is responsible to produce drawing and take approval before placing order. make of mccb : havells / schneider / siemens...

Due Date : January 25, 2023

Tender Value : ₹ 50 Lakhs

13

Railtel Corporation Of India Limited - Punjab

35318259 supply of procurement of electrical ( general ) items in connection with up gradation of signalling from standard i to standard ii ( r ) with electronic interlocking ( ei ) at 5 stations ( i.e. verka, kathunangal, jaintipura, batala, chhina ) on asr ptk section of firozpur division., supply of active lightening arrestor of class a for building protection as per standard nfc 17 102. it shall work on early streamer emission principle and shall be made of stainless steel with a t of 60 micro seconds. a non resettable type counter should also be supplied to count the number of lighting occurrences. it also includes supply of electrolytic copper tape of 25mm x 2mm of better to connecting class a devices to the earth pit. this includes installation, testing and commissioning of class a device on top of the building. this device should be installed at suitable height on top of the building using a gi mask as per the instruction of rcil engineer at site. the device should be connected to earth pit using a copper tape of 25mm x 2mm or better. this copper tape should be run firmly only the side of mask with the help of spacers. it shall also be ensured that the down conductor shall not touch the building throughout. the down conductor shall be connected to the earth electrode using exothermic welding. a counter shall be installed at appropriate space to count the number of occurrences. all the accessories like spares, welding material etc. required for installation shall be arranged by the contractor. ( inspection by rdso ) . [ warranty period: 2 months after the date of delivery ] , supply of change over switch 200 amp. 3 phase, 415v ac, 50hz ( side handle ) four pole, make havels ihcffe 200 or superior. ( inspection by , supply of 1.1 kv grade lt xl / pe . insulated armored aluminum conductor cable, making good the damages end termination with aluminum crimping socket / plugs. provision of cable route markers etc. as required as per technical specification no. is 7098. size ( 2x70 sq. mm ) . ( inspection by , laying of 1.1 kv grade lt xl / pe .insulated armored aluminum conductor cable, making good the damages end termination with aluminum crimping socket / plugs. provision of cable route markers etc. as required as per technical specification. size ( 2x70 sq. mm ) . [ warranty period: 2 months after the date of delivery ] , supply of control and distribution panel for 10 kva auxiliary transformer for color light signaling supply in 25kv / ac traction system as per rdso technical specification no tl / spc / psi / cls / 0020 ( 12 / 02 with a&c slips no 1 to 4 latest connection as required. ( inspection by , erection testing & commissioning of control and distribution panel for 10 kva auxiliary transformer for color light signaling supply in 25kv / ac traction system as per rdso technical specification no tl / spc / psi / cls / 0020 ( 12 / 02 with a&c slips no 1 to 4 latest connection as required. [ warranty period: 2 months after the date of delivery ] ...

Due Date : January 10, 2023

Tender Value : ₹ Ref. Documents

14

State Bank Of India - Punjab

30516752 tender for electrical installation works of state bank of india items ups & raw power points, distribution boxes, control and distribution panels, panels (main panel, generator panel), ups distribution board, earthing, communication, supply of fixtures led light panel...

Due Date : January 15, 2022

Tender Value : ₹ Ref. Documents

15

Indian Institute Of Technology - Punjab

29725551 tender for supply and installation of advanced soil testing equipment tender for supply and installation of advanced soil testing equipment , main items : automated triaxial testing apparatus 1. a ) static triaxial cell ( detailed specifications as per annexure a ) , loading frame ( detailed specifications as per annexure a ) , pressure volume controllers ( detailed specifications as per annexure a ) , transducers ( detailed specifications as perannexure a ) , data logging and software package with following features ( detailed specifications as per annexure a ) , sample preparation accessories for the supplied standard sizes ( detailed specifications as per annexure a ) , main items : flexible wall permeability apparatus 2. a ) permeability cell ( detailed specifications as per annexure a ) , pressure volume controller ( detailed specifications as per annexure a ) , transducers ( detailed specifications as per annexure a ) , data logging and software package with following features ( detailed specifications as per annexure a ) , sample preparation accessories for 38mm and 50 mm specimens ( detailed specifications as per annexure a ) , main items : swcc testing apparatus 2. a ) swcc cell ( detailed specifications as per annexure a ) , loading frame ( detailed specifications as per annexure a ) , pressure volume controller ( detailed specifications as per annexure a ) , transducers ( detailed specifications as per annexure a ) , data logging and software package with following features ( detailed specifications as per annexure a ) , optional suitable standard pc ( detailed specifications as per annexure a ) , optional an air water distribution system shall be provided. the system should include a de aired water tank with at least 15 litres capacity and two distribution panel ( 4 way ) . ( detailed specifications as per annexure a ) ...

Due Date : November 18, 2021

Tender Value : ₹ Ref. Documents

16

Border Security Force - Punjab

28393598 construction of electrical service connection with xlpe armoured lt cable of size 3 . 5x185 sqmm from main dt panel near bus stop to electrical panel near residential qtr type 4 and type 3 of 181 bn bsf under shq bsf abohar ( laying of cables ) construction of electrical service connection with xlpe armoured lt cable of size3 . 5 x 185 sqmm from main distribution panel near bus stop to electrical panel near residential quartertype 4 and type 3 of 181 bn bsf under shq abohar ( laying cables...

Due Date : July 10, 2021

Tender Value : ₹ Ref. Documents

17

Guru Angad Dev Veterinary and Animal Sciences University - Punjab

27705460 electrical work for the fitting of distribution panel & relocation of solar panel earth at semen lab/ett at gadvasu, ludhiana...

Due Date : April 29, 2021

Tender Value : ₹ 1.60 Lakhs

18

Border Security Force - Punjab

25469629 repair and maintenance of main lt distribution panel , main feeder pillars and sub main feeder pillars installed at various locations in 02 bn bsf campus under shq bsf abohar...

Due Date : September 22, 2020

Tender Value : ₹ Ref. Documents

19

Northern Railway - Punjab

23717225 annual maintenance contract including repair / replacement of auto change over control & distribution panel board for colour light signalling in rri / pi cabin / other location including lc gates for two years over firozpur division....

Due Date : March 12, 2020

Tender Value : ₹ 24.94 Lakhs

20

Baba Farid University Of Helath Sciences - Punjab

23415980 tender for 600 kw roof top solar pv power plant ( net metering ) for various buildings of bfuhs , supply , installation testing & commissioning of grid interactive pv system solar power plant ( i . e connected to utility grid ) of minimum 335 wp including required quantities of spv modules formed in to arrays , their mounting arrangement , power conditioning units ( i . e string solar inverter ) required dc & ac distribution panels with surge protection units , cabling from terrace to main distribution board through cable tray bi directional energy meter required earthing ( i . e gi strip earthing for gi strcuture , gi strip earthing for for string inverter ac & dc distribution system , 3 nos chemical earthing with copper bonded rods along with high rise gpsp structure ( rated wind speed 170kph ) including mounting height up to 8 feet completed with transportation , fabrication labour & civil work . a ) features : 1 ) solar pv module warranty 25 year & certified under is/iec 61730 , i & ii , is/ iec 61701 & is/ec 14286 2 ) power conditioning unit ( string solar inverter ) & certified under iec/en62109 1 , iec/en 62109 2 , en 61000 6 2 , en 61000 6 3 , iec 61683 , en 50530 , iec 60068 2 1 , 2 , 14 , 30 , en 605293 ) stucture 25 year service life with amc & certified under is 2062 2011 4 ) complete plant insurance for the period of 5 year ( excluding theft of the material ) 5 ) annual maintenance contract for the period of 5 yearsb ) make1 ) solar pv module = tata/ exide/ trina/ jackson/ rec/ luminios/ canadian solar 2 ) power conditioning unit = growatt/ sma/ kaco/ fronius3 ) ac/dc distribution board switch gear = embro , abb , schneider electric , havells4 ) mount structure = galvanized high quality5 ) ese stroemaster with chemical earthing sabo , jmc , tp , high gridc ) including processing fee as per calculation for pspcl charges ( according to pspcl regulatory act ) d ) the work will got done from the approved vendors of peda ( punjab energy development agency ) having 500 kw or more installing capacity . e ) bi directional meter supply , installation testing & commissioning ...

Due Date : February 13, 2020

Tender Value : ₹ Ref. Documents

21

Diesel Loco Modernization Works - Punjab

21603779 supply of power distribution panel, power distribution panel detail description as annexure attached make : hensel, cape,schneider or equal...

Due Date : September 17, 2019

Tender Value : ₹ Ref. Documents

22

Metal Scrap Trading Corporation Limited - Punjab

20089825 auction sale of lot no: 4 lot name: power distribution panel etc...

Due Date : May 06, 2019

Tender Value : ₹ Ref. Documents

23

Indian Railway - Punjab

17950496 tender for distribution panel for pantry equipmentsas per cc72172,alta...

Due Date : November 16, 2018

Tender Value : ₹ Ref. Documents

24

Border Security Force - Punjab

17193640 construction of electrical service connection with xlpe armoured lt cable of size 4 x 300 sqmm from generator room panel to main distribution panel near bus stop of 181 bn bsf under shq bsf abohar...

Due Date : September 04, 2018

Tender Value : ₹ 7.15 Lakhs

25

Border Security Force - Punjab

17021499 construction of electrical service connection with xlpe armoured lt cable of size 4 x 300 sqmm from generator room panel to main distribution panel near bus stop of 181 bn bsf under shq bsf abohar...

Due Date : August 16, 2018

Tender Value : ₹ 7.15 Lakhs

26

Military Engineer Services - Punjab

14873067 repair and replacement of unserviceable distribution panel with connected accessories at jalsa location, job work...

Due Date : January 22, 2018

Tender Value : ₹ 2.62 Lakhs

27

Military Engineer Services - Punjab

14873063 repair and replacement of unserviceable distribution panel with connected accessories at jalsa location, job work...

Due Date : January 22, 2018

Tender Value : ₹ 2.62 Lakhs

28

Military Engineer Services - Punjab

14872728 repair and replacement of unserviceable distribution panel with connected accessories at jalsa location, job work...

Due Date : January 22, 2018

Tender Value : ₹ 1.78 Lakhs

29

Central Public Works Department - Punjab

14719213 annual repair and maintenance of , diesel generator set and pumps set / 2017 18. sh: detecting fault location in main distribution panel and replacement of burnt out accessories.=> short tender notice...

Due Date : January 02, 2018

Tender Value : ₹ Ref. Documents

30

Department Of Electronics And Information Technology - Punjab

14351352 sale of scrap 1. electrical items broken tube light fixture and fitting 2. electrical distribution panel box 2. iron items 1. iron grills, raillings 2. iron sign boards 3. iron pipes and angle partitions 4. shutters 5. door and window frame iron 3. wooden item 1. palmets wooden 2. sealing board 3. wooden door frames 4. general items 1. aluminum fitting 2. pvc partition 3. vanishing blinds...

Due Date : December 22, 2017

Tender Value : ₹ Ref. Documents

31

Border Security Force - Punjab

13584834 repair / replacement of distribution panels and associated ug cables under ftr hq bsf jalandhar...

Due Date : September 18, 2017

Tender Value : ₹ 8.89 Lakhs

32

Border Security Force - Punjab

13573296 repair / replacement of distribution panels and associated ug cables under ftr hq bsf jalandhar...

Due Date : September 18, 2017

Tender Value : ₹ 8.89 Lakhs

33

Semi-Conductor Laboratory - Punjab

13193632 supply of electrical distribution panel...

Due Date : August 21, 2017

Tender Value : ₹ Ref. Documents

34

Rail Coach Factory - Punjab

13060975 supply of distribution panel for pantry equipments as per cc72172, alt a...

Due Date : July 27, 2017

Tender Value : ₹ Ref. Documents

35

Rail Coach Factory - Punjab

13028887 supply of distribution panel for pantry equipments as per cc72172, alt a...

Due Date : July 27, 2017

Tender Value : ₹ Ref. Documents

36

Border Security Force - Punjab

13020533 tender for repair and maintenance of ug cable distribution panel in 90 bn hq under shq bsf abohar...

Due Date : July 17, 2017

Tender Value : ₹ 97340.0

37

Rail Coach Factory - Punjab

11681765 distribution panel for pantry equipments...

Due Date : February 17, 2017

Tender Value : ₹ Ref. Documents

38

All India Radio - Punjab

11337997 supply installation testing and commissioning of lt distribution panel at dtt hpt doordarshan amritsar punjab...

Due Date : January 12, 2017

Tender Value : ₹ 8 Lakhs

39

Border Security Force - Punjab

11311900 rewiring of internal electrification and distribution panels installed in composite hospital of ftr hq bsf jalandhar...

Due Date : December 28, 2016

Tender Value : ₹ 13.51 Lakhs

40

Border Security Force - Punjab

11239584 rewiring of internal electrification and distribution panels installed in composite hospital of ftr hq bsf jalandhar...

Due Date : December 28, 2016

Tender Value : ₹ 13.51 Lakhs

41

Border Security Force - Punjab

11236125 tender for in rewiring of internal electrification and distribution panels installed...

Due Date : December 28, 2016

Tender Value : ₹ 13.51 Lakhs

42

National Fertilizers Limited - Punjab

10728649 supply of distribution panel...

Due Date : October 14, 2016

Tender Value : ₹ Ref. Documents

43

Border Security Force - Punjab

10460656 procurement of store for day to day maintenence of bfls control and distribution panel of bfls for 164 bn bsf under shq bsf gsp....

Due Date : September 09, 2016

Tender Value : ₹ 2.96 Lakhs

44

Border Security Force - Punjab

10419431 procurement of store for day to day maintenance of bfls control and distribution panel of bfls for 164 bn bsf under shq bsf gsp...

Due Date : September 09, 2016

Tender Value : ₹ 2.96 Lakhs

45

Rail Coach Factory - Punjab

10394435 distribution panel for pantry equipments...

Due Date : September 09, 2016

Tender Value : ₹ Ref. Documents

46

Rail Coach Factory - Punjab

10367863 distribution panel with wago terminal block complete with housing...

Due Date : September 14, 2016

Tender Value : ₹ Ref. Documents

47

Public Health Engineering Department - Punjab

10035508 tender for rehabilitation of main distribution panel i installed....

Due Date : July 26, 2016

Tender Value : ₹ Ref. Documents

48

Border Security Force - Punjab

10014610 procurement of store for day to day maintenance of bfls control and distribution panel of bfls for 164 bn bsf under shq bsf gsp...

Due Date : July 15, 2016

Tender Value : ₹ 2.96 Lakhs

49

Border Security Force - Punjab

10007450 procurement of store for day to day maint of bfls control and distribution panel of bfl for 164 bn bsf under shq bsf gsp...

Due Date : July 15, 2016

Tender Value : ₹ 2.96 Lakhs

50

Rail Coach Factory - Punjab

8539619 supply of distribution panel for pantry equipments...

Due Date : November 18, 2015

Tender Value : ₹ Ref. Documents

1
2