Military Engineer Services - Punjab

34098993 repair / replacement / maintenance external ht network including ht equipment and allied works at mil stn suranussi under ge kapurthala please refer tender documents supply only new insulating transformer oiland filling after dehydration of transformeroil to obtain di electric strengthnot less than 50 kv at 4 mm gap , conforming to is 335, filling in repaired transformer or for topping up of transformers installed at site complete all as specified and as directed at site by engineer in charge . make of oil : power oil / savita / indian oil or equivalent. 2 dehydration and filtration of transformer oil / voltage stabilizer oil at site of installation for 11 kv, 433 step down transformer of any capacity and any make installed on poles / plinth mounted indoor / outdoor and obtaining di electric strengthminimum 50 kv ( r.m.s ) with in 1 minute with 2.5 mm gapwith portable filtrationcum dehydration machine. note : ( testing of di electric strengthof dehydrated transformer oilof each transformer / voltage stabilizer will be carried outin the presence of engr in charge. ) 3 disconnecting of ht / lt side connection of transformer afterdisconnecting electric supply opening / disconnecting the foundation earth and neutral connection out side of the transformer and taking down the transformer any capacity up to 250 kva from 2 / 4 polestructure including loading transportation and unloading to workshop / factory drainning out transformer oil or site to avoid dust and moistureand back to yard / site after repair complete all as specified and directed. note: ( i ) the rate quoted for this item deemed for lifting and shifting the transformer will be done by crane where ever posible to lift with crane 4 opening of transformer cover and all other connected accessories taking out the transformer oil from tanktaking out core assembly disconnecting the core and taking out unserviceable ht / lt coil after opening / dismantling allconnection inside the transformer capacity up to 250 kva and reassembling the rewinding ht / lt coil and transformer oil in original positionwith making alignment for smooth functioning the transformer and replacement of burnt out lt / ht bush and gasket to avoid leakage of oil, refilling back oil into the transforme complete all as specified and directednoteii ) centrifuging of transformer oil shall be measured and paid seperately ii ) repair work of transformer shall be measured and paid seperaetely ( iii ) .the transformwer rewinding work shall be carried out at certified renowned workshop / company ( iv ) the all type of transformer tests shallbe carried out before installing the rewounded transformer in the presence of engr in charge. 5 supply and fixing / winding fabricated dpc copper strip of suitable guage / size andrequired shape forrewinding of lt coil of transformer up to250 kvaincluding necessaryovening and insulationmaterial completeall as required an directed. 6 all as per above item no 5 but using copper wire of suitablesize / guage and shape for rewinding of ht coil including necessary insulation material complete all as required and directed . 7 supply only tap changer switch suitable for outdoor / indoor type for transformer of capacity upto 250 kva, suitable for fixing on hv side tovary the voltage on lv side upto +7.5% in steps of 2.5% complete all as specified and directed. 8 s&f in replacement of unserviceable porcelainvitreous bushing of required size / shape ( suitable for existing transformer ) for spindle of transformer of any capacity upto250 kva 11kvoutdoor type siutable for ht side all as specified and directed. 9 same as above but 11000 volts grade suitable for ht side indoor type 10 same as above but 1100 volts grade suitable for lt side indoor type 11 same as above but 1100 volts grade suitable for lt side outdoor type 12 s&f in replacement ofunserviceable brass spindle duly threded at theendcompletewith nut bolts and washer suitable for ht side of transformer out door type all asspecified and directed at sitefor the following capacitysuitable for existing transformerof required size / shapefor spindle of transformer of any capacity up to 250 kva 11000 volts grade outdoor type suitblefor ht side all as specified and directed : 13 63 kva 14 100 kva 15 160 kva 16 200 / 250 kva 17 all as above item but suitable for lt side of transformer of following capacity 18 63 kva 19 100 kva 20 160 kva 21 200 / 250 kva 22 m&l for transporting transformer and making all necessry connection of any capacity up to250 kvaon2 pole / 4 polesturucture from any locationto another location at suranussi including loading / unloadingor depositing the transformer to e / m yard or other locationin the area under ge kapurthala completeall as specified and directed at site. 23 supply and fixing thetransformer silica gel breather complete with all accessories for transformer of any capacity up to 400 kva all as directed at site. 24 m&l transformer silica gelcomplete with all accessories for transformer of any capacityall as directed at site. 25 s&f lightning arresters expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp for suitable 11000 volts. 26 supply and fix gi tubing light grade for encasing cables for mechanical protection, laid under plinth / floors / roads / path / culverts or fixed on walls / on poles by means of msclamps with necessary bolts, nuts and washers all as specified of sizes 100 mm bore 27 dismantling & taking down existing acsr conductor of any size by opening the binding wire from ht electric poles complete all as specified. 28 taking downcross arms, channels, angle iron, clamps, nut, bolts, stay wire, stay assembly, gi wire, anti climbing devices, danger notice boards etc complete al assoecified and directed . 29 taking down old rusted gi pipe of any size from pole / trench complete all as specified. 30 taking down insulators off size & type all as specified. 31 supply and fixing and stringing in replacement acsr conductor ( weasal / ferret / squirrel ) on lt poles / service brackets including binding of conductor with aluminum binding wire complete all as specified and directed. 32 supply and fixing ms cross arms, bracing, supports, clamps and back plates fabricated from structural steel section including nuts, bolts, washers, welding bending, cold or hot, drilling joles or bolt in any shape of size including 2 coat of aluminium paint over a coat of red oxide primer complete all as specified and directed. 33 repairing, greasing and setting of god triple pole 11 kv 200 / 400 amps complete with replacement of old unserviceable parts and setting alignment for its smooth operation including taking out old parts all as directed. note : new parts required for repiring shalll be measured & paid separately under relevant items as supply only. 34 supplying only the following items: 35 post insulator for triple pole 11 kv upto 400 amps god. 36 male contact assemble with arcing horns suitable for 11 kv 37 female contact / fix contact jaw assembly suitable for 11 kv ab switch. 38 tinned copper flexible jumper upto 400 amps suitable for 11 kv ab switch 39 back connector plate suitable for 11 kv ab switch. 40 tightening and restringing existing loose / broken conductor ( acsr ) continuous earth wire any type including stringing including replacement of fresh binding wire all as required at site all as directed. 41 supply and fixing pin type insulator porcelain viterous white brown or green incl one galvanised mild steel spindle two galvanised iron washer and one galvanised iron nutrs 150 mm height, 150 mm dia for11000 volts grade. makejaipur / rashtriya 42 supply and fixing disc type composite polymeric insulators, 11000 volts grade, 45 kn, with tension clamps, bolts, nuts etc complete all as specified and directed . makejaipur / rashtriya 43 supply and fixing loop type insulator porcelain vitreous, white or brown for ht saylarge size with overall diamensions 90 x 140 mm, clearance hole25.5 mm for 11000 volts grade. make jaipur / rashtriya 44 supply and fixing for danger notice plate for ht of 25 cm x 20 cm x 1.6 mm thick mild steelsheet vitreous enameled white, with letters figures and conventional skuull and bones and written as danger in signal red colour and fixed with ms clamps made out of ms flat 25 mm x 3 mm , including nuts &bolts including 2 coats of aluminium paint over a coat of red oxide primer all as specified. note : instructions are to bewritten in three languages viz punjabi hindi and english. 45 dismantling and taking down go switch off size including, operating machanismetc complete from any position. 46 supplying and fixing switch air break gang operated switch outdoor type ht 11 kv triple poles upto 400 amps withfixed contacts of phosphorus bronze and moving contacts of copper withmechnically operating from ground level vertical mounted complete with ht insulator on steel frame operating rod made out of25 mmgi pipe medium grade worked from ground level with handle and locking arragement with12 insulators with drop out fuses complete all as per specified and directed by engr in charge and ( clamps / cross arms shall be measured and paid for separately ) make : jaipuria / rashtrya. 47 supply, fixing and testing & cable jointing kit for 11 kv grade cable for indoor type ermination cold shrinable joint complete with joining material and accessories suitable for xlpe armoured aluminium cable of size 95 sqmm 3 core. make : denson / m seal / raychem. 48 all as per item no 34here in before in before but of size 120 sqmm to 185 sqmm 3 core. 49 supply, fixing and testing after jointing cable jointing kit for 11 kv grade cable for outdoor type termination cold shrinkable joint complete with jointing material and accessories suitable for xlpe armoured aluminium cable of size 95 sqmm 3 core.make denson, m seal / raychem 50 all as per item no 36here in before in before but of size 120 sqmm to 185 sqmm 3 core. 51 supply, laying and testing cable xlpe insulated, screened, pvc bedded, galvanisedsteel striporwire armoured, electric power cables ( heavyduty ) with aluminium conductor, 11000 volts, grade cross sectional area 95 sqmm 3 core. 52 supply, laying and testing cable xlpe insulated, screened, pvc bedded, galvanisedsteel striporwire armoured, electric power cables ( heavyduty ) with aluminium conductor, 11000 volts, grade cross sectional area 120 sqmm 3 core. 53 supply and fix cable jointing kit for 11 kv grade cable for straight through cold shrink type joint complete with jointing material and accessories suitable for 3 core xlpe armoured al conductor cable of size 95 sqmm 54 supply and fix cable jointing kit for 11 kv grade cable for straight through cold shrink type joint complete with jointing material and accessories suitable for 3 core xlpe armoured al conductor cable of size 120 sqmm 55 m&l for filling and levelling with 40mm graded stone gravel thickely packed 150mm thick all around the transformer / panel / 2 pole structure area complet for protectionall as required and directed at site. 56 excavation over areas in soft / loose soilnot exceeding 1.5 mtrdeep and not exceeding 1.5 mtrwide for laying of cables, poles / stays and struts etc and getting out including trimming sides and forming bottom surface all as specified and directed at site. 57 returning, filling in including spreading, leveling, watering and well ramming excavated hard / soft in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested, poles, stays , struts have been erected and tested, all as specified and directed. 58 removing excavated surplus soil ( soft / loose soil ) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed. 59 material and labour for clean dry sand laidin trenches / ducts for cushioning to cable complete all as specified. 60 supplying and laying cable cover precost concrete class hv, type i, flat, size 300 mm x 180mm x 40mm 61 m&l for earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground earth pit not less than 2.25 mtr below normal gl with the top edge of the plate not less then 1.5 mtr below the normal gl connected to gi strip 32 x 6mm by means of bolts, nuts, check nuts and washer of galvanised iron or steel and protected by 40mm gi pipe ( light grade ) and watering pipe 20mm bore gi pipe ( light grade ) including gi wire meshed funnel and chamber pcc ( 1:4:8 ) type d2 using 40mm grade stone aggregate, coping shall be ( 1:3:6 ) type ci using 20mm stone aggregate with rcc 1:2:4 type b1 ( using 20mm graded stone aggregate ) pit cover re inforced with 8mm dia at 80mm c / c both way in lieu of ci pit cover with angle iron frame, including excavation and earth work in any type of soil and removal of surplus soil of earth complete all as shown in electrical plate of ssr part i and as specified including charcoal dust, common salt complete and earth lead connected to earthing test point all as specified and testing of earthing on completion. note 1. the unit rate includes for protection pipe and gi strip 32x6mm from top of earth plate up to 7.5 meter above ground level. 62 material and labourfor prunning of tree branches of any sizes and dia, not less than 2 mtr around the lt / ht oh line which obstructing the power supply / maintenance of electric supply as well as illumination in area including repair of damage broken acsr conductor, gi wire and jumpers and disposed exc 50 mtr away clearing area complete testing of line all as directed. ( note : ( i ) rate quoted inclusive are repair to damage work in item ( ii ) each span approx 30 40 mtr ) . 63 taking down ht switch gear ( vacuum circuit breaker ) of capacity 630 to 800 amps, 11 kv upto 350 mva of make crompton / siemens inlcuding, overhauling, repairs servicing and refixing the same to its original position after repairs, overhauling carried out through oem and comprising of the following: ( a ) tripping off the breaker, isolating the breaker with handle, disconnecting breaker control socket and pulling out the breaker complete from the panel along with the trolley for servicing / inspection / overhauling. ( b ) servicing / inspecting / checking of automatic safety shutter operation for serviceability with electrical inter locking / indication limit switches and replacement of required spares as directed by eng in charge. ( c ) servicing / inspecting / checking of circuit & bus spout and circuit & bus spout connections for ryb phases, applying petroleum jelly on spouts, applying one coat of insulation paint on spout insulation ( d ) dismantling and checking of cross bar assembly, fixed contacts and current carrying parts of the breaker, trolley, insulated assembly and checking lamination with clamps, epoxy spout, isolator assembly etc. ( e ) setting, reassembling, cleaning, adjustment of fixed contacts, chamber baffle pot assembly, moving contact for proper setting of auxiliary contacts operating mechanism. ( f ) servicing / inspecting / checking of secondary scokets / bus bar earthing plugs / earthing sockets and replacement of spares if required. ( g ) checking / setting and adjustments of services and isolate operation of the breaker trolley. ( h ) lubrication and greasing of all moving parts of the trolley, stopper bot for proper operating and closing of shutter gear, isolation resistance of vaccum interruptor assembly. ( j ) dismantling the complete cable chamber, decrabuzing chamber inspecting cable earthing.decrabonizing / cleaning the complet. ( k ) ht 11 kv 3 phase independent bus bar, bus bar chamber of ht panel and inspecting the bus bar insulators, applying one coat of epoxy insulation paint on insulators, cts pt bushings, cablechambers and if flash has been happended testing ir value. ( note : new parts required for repiring shalll be measured & paid separately under relevant items as supply only ) . 64 supplyingthe following items : 65 space heater suitable for ht vcb 11 kv of make crompton 66 big gearsuitable for ht vcb 11 kv of make crompton 67 small gearsuitable for ht vcb 11 kv of make crompton 68 amperemeter 2 x 2 square shaped range 0 200 amps ct ratio 100 / 50 / 5, make ae 69 voltmeter 2 x 2 square shaped range 0 15 kv pt ratio 11000 / 110 volts, make ae 70 segmented gearsuitable for ht vcb 11 kv 71 indicator red, green, amber ( volt 24 to 220v ac / dc ) suitable for ht vcb 11 kv 72 indicator blue & white ( volt 24 to 220v ac / dc ) suitable for ht vcb 11 kv 73 power pack dc for auxiliary power supply to operate closing & tripping coils, protection relay circuits & other indication lamps for 11 kv ht vcb panel suitable to operate the control circuit on in put supply 230 volts ac + 10% to 30 %, 50 hz to give an out put supply of 110 v, dc complete all as directed. make : gogate electro systems ( p ) limited / alan power pack 74 breaker auxilary switch ( 7no / 7nc ) 75 breaker control switch ( tnc switch ) 76 current transfomer suitable for 11 kv200v 100 / 5+5a of primary wounded type, core 1 15 va, class 1.0, core 2 15 va class sp10 and epoxyconforming to iec 60186 all as directed. make : cg / areva / southen switchgear 77 isolating contactsuitable for ht vcb 11 kv 78 spout bushings suitable for ht vcb 11 kv of make crompton 79 fuse link with capacity 63 100a for ht 11 kv 80 hrc berral fuse, 3 amps ( pt ht side ) 81 crc ( 2 26 ) of 500 ml unit for cleaning of vcb parts 82 testing ofrelay with digital protective relay three phase 11kv over current and earth fault relays of ct ratio 50 / 25 / 5 smooth functioning of relay and necessary connection with copper wire and setting according to the existing load of the panel by approved company rep and explain to the mes rep to further handle if necessary complete all as required and directed. 83 caliberation of electro mechanical relay with digital protective relay three phase 11kv over current and earth fault relays of ctratio 100 / 50 / 5 and30 / 15 / 5smooth functioning of relay and necessary connection with copper wire and setting according to the existing load of the panel complete all as required and directed. 84 supply, fixing and testing of three phase 11kv over current and earth fault relays of ct ratio 100 / 50 / 5smooth functioning of relay and necessary connection with copper wire and setting according to the existing load of the panel complete all as directed. 85 m&l for scrapping down old painted surfaces of ht pole, applying two coatsred colour synthetic enamel paint overone coat of red oxide primerusing spray jet and lettering of ht polenumber with white colour of approved make: berger / asian complete all as specified &directed by engineer in charge. 86 matterial, labour & transportation for locatingfault of ht / lt under ground cable with cable fault locating machine and locate any pin point faults in lt / ht cables upto 11 kv cables including following instruments: ( i ) impulse generator 0 11 kv. ( ii ) acoustic fault locator to pin point the fault exactly at fault point ( iii ) reflectometer ( laptop based ) tdr set =input wave capturing ( iv ) high voltage murray loop for % distance to constant leakage faults ( v ) cable fault locating machine mounting on sutable vehicle. 87 transformer head gasket cut & made to shape with provn of reqd holes as per original for transformer of capacity upto 315 kva. 88 m&l for scrapping down old painted surfaces oftransformer and preparing the surface for painting, applying two coats synthetic enamel paint overone coat of red oxide primerusing spray jet of approved make: berger / asian including cleaning and degreasing the surface complete all as specified &directed by engineer in charge. 89 s&f informatory name board of size 1200 mm x 900 mm made of aluminium sheet 2 mm thick with stainless steel rectangular frame using 25 x 15 mm rectangualr pipe with 35 mm dia stainless pipe inouter border all around retro reflective high intensity 400 micron thick blue colour sheet pasted with heating process on both sides of the board including 75 mm to 100 mm high white colour letters cut to shape with special plotter and in proper manner indicatingsub station no / name and location of installation as directed by engr in charge, 02 nos 75 mm dia stainless steel pipes of 304 grade glossy finish with ms plate 3 mm thick welded at bottom of pipes shall be provided.the board shall be fixed at height of 3.00 m ( top level of board ) above gl and shall be embedded in ground using pcc 1:2:4 type b 1 of min size 300 mm x 300 mm x 600 mm including necessary form work, excavation and earth work complete all as specified and directed. 90 supplying and laying synthetic rubber insulated mats 2.5 mm thick for voltage upto 11 kv for electrical purpose as per is 15652 2006, ( superseding is 5424 ) suitable for electrical shock safety of sizes 2m x 1m....

Military Engineer Services - Punjab

33626982 provision of certain sanctioned work at age b / r beas under ge kapurthala 1 demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed by engineer in charge. 2 taking down cement or cement lime plaster, any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed by engineer in charge. 3 taking down chowkats or frames with shutters not exceeding 1.5 sqm each ( without taking off shutters from the frames ) , complete all as specified and directed by engineer in charge. 4 taking down chowkats or frames with shutters exceeding 1.5 sqm but not exceeding 4 sqm each ( without taking off shutters from the frames ) . complete all as specified and directed by engineer in charge. 5 dismantling taking down framed trusses of span not exceeding 10m, complete all as specified and directed by engineer in charge. 6 dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by engineer in charge. 7 dismantling asbestos cement ( corrugated, semi corrugated, etc. ) sheets in roof coverings including ridges, complete all as specified and directed by engineer in charge. 8 dismantling wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thicknness, including cover fillets, complete all as specified and directed by engineer in charge. 9 demolition of cement concrete ( unreinforced ) in ground floors and pavings not exceeding 15cm thickness below or above ground level including tiles, terrazzo / stones etc. complete all as specified and directed by engineer in charge. 10 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by engineer in charge. 11 m&l for brickwork with subclass ‘b’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed by engineer in charge. 12 ditto all as per item no 11 above but except bricks etc. complete all as specified and directed by engineer in charge. 13 m&l for brickwork with subclass ‘b’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4. complete all as specified and directed by engineer in charge. 14 m&l for brick work with sub class b bricks using old size bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4. complete all as specified and directed by engineer in charge. 15 m&l for brick work with sub class b bricks using old size bricks straight or curved on plan exceeding 6m mean radious built in cm1:6 etc complete all as specified and directed by engineer in charge. 16 m&l for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls, finished even and smooth without using extra cement, complete all as specified and directed by engineer in charge. 17 m&l for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls, finished even and smooth without using extra cement, complete all as specified and directed by engineer in charge. 18 m&l for 15mm thick rendering in cement mortar 1:4 on brick or concrete surfaces with liquid water proofing compound, finished even and smooth without using extra cement etc including neeru finish to plastering complete all as specified and directed by engineer in charge. ( note : water proofing compound shall be measured and paid separately ) . 19 supply only integral water proofing compound complete all as specified and directed by engineer in charge. 20 m&l for preparation of new plastered surfaces and applying two coats of cement base paint over and including a coat of chalk whiting / priming on plastered surfaces of walls, complete all as specified and directed by engineer in charge. 21 m&l for preparation of new plastered surfaces and distempering walls with two coats of distemper oil emulsion, white or tinted over and including 1mm thick wall care putty including primer, complete all as specified and directed by engineer in charge. 22 m&l preparation of newly plastered surfaces and applying two coats of white wash over a coat of chalk whiting / priming on plastered surfaces of walls etc. complete all as specified and directed by engineer in charge. 23 m&l for framed work as in doors or gates and chowkhats of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening conforming to gdefe 290 ( gde e 165 ) . complete all as specified and directed by engineer in charge. 24 s&f rolled sections fe 410 w ( gde e 250 ) quality a, as in main and cross beams, hip and jack rafters; purlins where connectedto common rafters and running rails and guides for sliding doors; fixedwithangle cleats or other connecting plates . complete all as specified and directed by engineer in charge. 25 s&f steel work in tubular trusses including special shaped washer etc. complete using erw or induction butt welded tubes conforming to i. s.1161 1979 grade st. 240. complete all as specified and directed by engineer in charge. 26 s&f ms pipes as in vertical posts, fixed with angle cleats or other connecting plates, rivets , nut bolts etc, complete all as specified, conforming fe 410w ( gde e 250 ) quality b. complete all as specified and directed by engineer in charge. 27 erection and fixing only steel work in tubular trusses including special shaped washer etc. complete using erw or induction butt welded tubes conforming to i. s.1161 1979 grade st. 240. complete all as specified and directed by engineer in charge. 28 erection and fixing only steel tubular work as in purlins including special shaped washer etc. complete using erw or induction butt welded tubes conforming to i. s.1161 1979 grade st. 240. complete all as specified and directed by engineer in charge. 29 s&f pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed by engineer in charge. 30 s&f pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed by engineer in charge. 31 s&f wind tie for roof including securing bolts: flat iron fillets including all necessary drilling, bolting or riveting, etc, and similar work conforming to fe 410 0 or fe 310 0 etc. complete all as specified and directed by engineer in charge. 32 s&f 2nd class hard wood 35mm thick plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 ( part i ) , kiln seasoned and chemically pressure treated, complete all as specified and directed by engineer in charge. 33 s&f 2nd class hw 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. ( without sash bars ) , edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me mbers of shutters as specified in ssr part i, section 8, clause 8.24 ( a ) ; supplied and fitted to chowkats complete all as specified and directed. 34 s&f steel window 1.25mm thick box type ( primer coated ) erw hollow p section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter erw sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two nos sash bar of t section 20mm x 3mm complete welded to frame with one vertical mullion of erw box type t section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in pcc ( 1:2:4 ) type b 1 four nos for each window including following fitting welded to frame shutter : ( a ) hold fast, 150mm long of 12mm square bar made to shape 04 nos per window ( b ) handles ofz section 100mm long ( c ) stopper 01 no per leaf ( d ) cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges 01 no per leaf ( e ) ms pintal hinges of size 75mm x 75mm x 12mm 02 nos per leaf ( f ) fabrication & fixing arrangement as per drg no cejz / td 7 / 07 sheet 1 / 3 to 3 / 3.note : glass and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed. 35 s&f steel window 1.25mm thick box type ( primer coated ) erw hollow p section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter erw sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two nos sash bar of t section 20mm x 3mm complete welded to frame with one vertical mullion of erw box type t section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in pcc ( 1:3:6 ) type c 1 four nos for each window including following fitting welded to frame shutter : ( a ) mild steel hold fast, 150mm long of 12mm square bar made to shape 04 nos per window ( b ) handles ofz section 20mm x 100mm long ( c ) stopper 01 no per leaf ( d ) cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges 01 no per leaf ( e ) ms pintal hinges of size 75mm x 75mm x 12mm 02 nos per leaf ( f ) grills made out of ms square bar 12mm dia welded to fi frame complete all as specified and shown on drawings. note : wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed. 36 s&f steel ventilator1.25mm thick box type fixed type prepared for fixing of gauzed and glass ( primer coated ) erw hollow p section of size 60mm x 25mm including cutting holes and making good dismantled portion in pcc ( 1:3:6 ) type c 1 four nos for each vent ) including following fitting welded to frame shutter: ( a ) mild steel hold fast, 150mm long of 12mm square bar made to shape – 04 nos per vent ( b ) handles of z sec 20mm x 100mm long ( c ) stay ( d ) cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 noper leaf ( e ) mild steel pintal hinges of size 75mmx75mmx12mm 02 nos ( f ) grills made out of ms square bar 12mm dia welded to fi frame complete all as specified and shown on drawings. note: wire mesh / glass pane and painting shall be measured and paid separately under appropriate item etc. complete all as specified and directed by engineer in charge. 37 s&f in repairs wire netting of galvanised steel wire 1.40mm having size of mesh 12mm dia fixed with tinned tacks of wire staples, complete all as specified and directed by engineer in charge. 38 s&f 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane, complete all as specified and directed by engineer in charge. 39 s&f 4mm thick figured glass, pinhead type in squares not exceeding 0.5 sqm each pane, complete all as specified and direct by engr in charge. 40 s&f galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed by engineer in charge. 41 s&f powder coated of any colour anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long ( 1 no. ) . hinges type b 21 100mm long ( 2 no. ) suitable handle ( 1 no. ) etc. complete all as specified and directed by engineer in charge. ( thickness or powder coating should not be less than 50 micron ) 42 s&f solid pvc door frame of size 50mm x47mm made out of 5mm wood grain printed pvc sheet reinforced with m.s. square tube and edges will be painted to match with printed sheets, suppyling & fixing in opening as per specification & drawing. complete all as specified and directed by engineer in charge. 43 s&f factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded wood grain printed pvc sheet ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; & 5mm thick x 15mm wide pvc sheet beading use inside stiles and rails and decorative pvc beading of 10mm x 10mm ( 90 degree ) used.panelling of wood grain printed pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed by engineer in charge. 44 all as per item no.43 above but wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed pvc sheet panel. the wire gauze shall be wrapped on an additional square 8mm m.s. solid tube and this tube shall be welded to m.s. tubes. the wire gauge shall be stretched to tighten firmly complete all as specified and directed by engineer in charge. 45 s&f anodised aluminium snap grid of size 605 x 605mm in frame work for false ceiling. complete all as specified and directed by engineer in charge. 46 providing and fixing gypsum board 8mm thick of size ( 600x600 ) mm in ceiling fixed with screw as per manufacturers instructions. complete all as specified and directed by engineer in charge. ( frame work for ceiling shall be measured and paid separately ) . 47 s&f mild steel pressed handles of size 150mm, oval type, stove enamelled black, complete all as specified and directed by engineer in charge. 48 s&f mild steel barrel tower bolts 200mm long, stove enamelled black, with bright bolt and fixed, complete all as specified and directed by engineer in charge. 49 s&f butt hinges 100mm size, medium weight, cold rolled mild steel, and fixed, complete all as specified and directed by engineer in charge. 50 s&f mild steel sliding door bolts 250mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by engineer in charge. 51 s&f mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by engr in charge. 52 s&f 100mm size stainless steel butt hinges, medium weight. complete all as specified and directed by engineer in charge. 53 s&f aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, length of bolt 250mm. complete all as specified and directed by engineer in charge. 54 s&f aluminium handles, cast type anodised of size 125mm etc complete all as specified and directed. 55 s&f 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed by engineer in charge. 56 m&l for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by engineer in charge. 57 m&l for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over and including a coat of red oxide primer. complete all as specified and directed by engineer in charge. 58 m&l for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by engineer in charge. 59 m&l for preparation of new wood surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer, complete all as specified and directed by engineer in charge. 60 m&l for 75mm thick cement concrete type d 2, 1:4:8 using 40mm graded stone aggregate as in subbase flooring, complete all as specified and directed by engineer in charge. 61 m&l for 75mm thick cement concrete type c 2, 1:3:6 using 40mm graded stone aggregate as in subbase flooring, complete all as specified and directed by engineer in charge. 62 m&l for cement concrete type d2 1:4:8 ( 40mm graded stone aggregate ) as in foundation, filling and mass concrete. complete all as specified and directed by engineer in charge. 63 m&l for cement concrete type c 2, 1:3:6 ( 40mm graded stone aggregate ) as in foundation, filling and mass concrete. complete all as specified and directed by engineer in charge. 64 m&l for 100mm thick cement concrete type b 1, 1:2:4 ( 20mm graded stone aggregate ) as in pavement / hard standingfinished even and fair without using extra cement including necessary form work and to divide the area in panels complete all as specified and directed. 65 m&l for 40mm thick pcc 1:2:4 type b 1 with 20mm graded stone aggregate as in flooring, finished even and rough to receive the topping layer. complete all as specified and directed by engineer in charge. 66 m&l for 150mm thick pcc 1:2:4 type b 2 with 20mm graded stone aggregate as in platform for urinal, finished even and rough to receive the topping layer. complete all as specified and directed by engineer in charge. 67 m&l for 75mm thick cement concrete type c 2, 1:3:6 ( 40mm graded stone aggregate ) as in plinth protection finished even and smooth ( without using extra cement ) . complete all as specified and directed by engineer in charge. 68 m&l for providing cement concrete 1:2:4 type b 1 ( using 20mm graded stone aggregate ) as in roof kerbs or mud stops, rounded or chamfered on edges. complete all as specified and directed by engineer in charge. 69 m&l for joint free non skid ceramic colouredtiles 7 to 8 mm thick square / rectangular ) laid over 15mm thick screed bed in cement mortar 1:6, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by engr in charge. 70 all as per item no 69 above but as in skirting in cement sand mortar 1:4. complete all as specified and directed by engineer in charge. 71 m&l for coloured glazed ceramic tiles in vertical surface 450mm x 350mm & 7mm thick laid over and including 10mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed by engineer in charge. 72 m&l for joint free non skid ceramic coloured tiles 7 to8 mm thick ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6. complete all as specified and directed by engineer in charge. 73 m&l for machine cut kota stone slab flooring 20 25mm thick over and including 20mm thick cement screed base in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, treating the surface with bees wax polish, complete all as specified and directed by engineer in charge. 74 m&l for kota stone slab 20 25mm thick in riser of steps, skirtings, dado and pillar, laid over and including 15mm thick cement screed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, treating the surface with bees wax polish, complete all as specified and directed by engineer in charge. 75 m&l hardcore of broken bricks ofgauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface. complete all as specified and directed by engineer in charge. 76 m&l for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed by engineer in charge. 77 m&lfor providing reinforced cement concrete cast in situ type b 1, 1:2:4 ( 20 mm graded stone aggregate ) as in lintels upto 1.5m clear span including necessary formwork complete all as specified and directed by engr in charge. ( note : reinforcement shall be measured and paid separately ) 78 m&l for tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips quality conforming to. complete all as specified and directed by engineer in charge. 79 ditto all as per item no 78 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders. complete all as specified and directed by engineer in charge. 80 m&l for reinforced cement concrete ( nominal mix ) type b 1 1:2:4 ( 20mm graded stone aggregate ) as in chajjas, complete all as specified and directed by engineer in charge. 81 use and waste for formwork to chullah hoods, chajjas, troughs and similar items including edges, complete all as specified and directed by engineer in charge. 82 m&l for reinforced cement concrete ( nominal mix ) type b 1 1:2:4 ( 20mm graded stone aggregate ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by engineer in charge. 83 use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal / sloping ) , fair finished surfaces concrete flat, complete all as specified and directed by engineer in charge. 84 use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floors and roofs exceeding 10cm but not exceeding 20cm wide and sides of rcc / pcc bands in walls, horizontal or sloping, and similar work for rough finished surface of concrete, complete all as specified and directed by engineer in charge. 85 m&l for 20mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like over and including cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed by engineer in charge. 86 m&l for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed by engineer in charge. 87 m&lpcc1:2:4 type b 1 ( 20 mm graded stone aggregate ) as in bed blocks, coping, etc. complete all as specified and directed by engineer in charge. 88 s&f rotational moulded polyethylene water storage tanks 1000 ltr capacity ( three layered ) ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified including 20mm dia ball brass valve, complete all as specified and directed by engineer in charge. 89 s&fvitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or eracting stand & waste pipe, coupling etc as in repairs complete all as specified and directed. 90 s&f gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to steel pipe orunion, 20mm bore dia of pipe. complete all as specified and directed by engineer in charge. 91 s&f in repairs, cp waste coupling, bore dia of discharge pipe 32mm. complete all as specified and directed by engineer in charge. 92 supply and fixing 15mm dia pillar taps, cast copper alloy with capstan heads chromium plated, screwed down high pressure, with or without lettered with long screwed shanks and fly nuts, screwed for iron pipe but fancy type and fixed etc. complete all as specified and directed by engineer in charge. 93 s&fvitreous china under counter top wash basin, snow white, oval type of size 560mm x 470mm x 190mm including brackets, cutting for and pinning in ends of brackets or eracting stand & waste pipe, coupling etc. complete all as specified and directed by engineer in charge. 94 s&f vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. complete all as specified and directed by engineer in charge. 95 s&f urinal spreader of cp any colour for fixing with 15 mm dia pipe. complete all as specified and directed. 96 s&f pvc waste pipe for wash basin, urinal etc. complete all as specified and directed by engineer in charge. 97 s&f 20mm thick makrana white marble slab, machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing, rounding to edges of stone slabs, fixed in walls as in urinal partition, complete all as specified and directed by engr in charge. 98 s&f15 mm dia fancy type chromium plated angle stop valve of any colour pressure screwed for iron pipe and fixed. complete all as specified and directed by engineer in charge.make : cera, jaguar, hindware. 99 s&f cp waste coupling suitable for urinals, bore dia of discharge pipe 32mm. complete all as specified and directed by engineer in charge. 100 s&f vitreous china squatting pan ( orissa pattern ) , size 580 x 440mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) complete including provision of lime concrete bedding. complete all as specified and directed by engineer in charge. 101 s&f vitreous china wash down water closet pan ( pedestal pattern ) , white ( excluding fixing bolts, flushing cistern and flush pipe ) complete including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices with recessed bottom, jet spray, etc. complete all as specified and directed by engineer in charge. 102 s&flow level flushing cistern pvc valveless syphonic action type, 10 ltrs capacity including supply pipe & fixing brackets of m.s. angle of size ( 25mmx25mmx3mm ) , 30 cm long in pcc ( 1:2:4 ) type b 1, block of size ( 10cmx10cmx10cm ) on walls, etc. complete all as specified and directed by engineer in charge. 103 s&f grating doom 100mm dia with waste hole ofcp. complete all as specified and directed by engineer in charge. 104 s&f 15mm dia fancy type long body pillar taps, cast copper alloy with capstan heads chromium plated, screwed down high pressure, with or without lettered with long screwed shanks and fly nuts, screwed for iron pipe but fancy type etc. complete all as specified and directed by engineer in charge. 105 s&f towel rail 600mm long of stainless steel fixed with and including chromium plated brassscrews and or cleats. complete all as specified and directed by engineer in charge. 106 s&f1800mm x 1200mm and 6mm thick bevelled edge mirror of selected quality glass, complete fixing including stainless steel spacers, mount stand bolt screws etc. complete all as specified and directed by engineer in charge. 107 s&f cp soap dish, any type, fixed to plugs with chromium plated brass screws. complete all as specified and directed by engineer in charge. 108 s&f 15mm dia chromium plated fancy type bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe and fixed to 15mm bore pipe fixed. complete all as specified and directed by engineer in charge. 109 s&f pvc connection 15mm size with ptmt nuts of length 450mm etc. complete all as specified and directed by engineer in charge. 110 s&f pvc ( swr ) p trap 110mm bore. complete all as specified and directed by engineer in charge. 111 s&f 110mm bore pvc ( swr ) wc connector with lip ring. complete all as specified and directed by engineer in charge. 112 s&f 110mm bore pvc ( swr ) junction single, ( single t ) equal or unequal. complete all as specified and directed by engineer in charge. 113 s&f 110mm bore pvc ( swr ) bends any radius. complete all as specified and directed by engineer in charge. 114 s&f 110mm bore pvc ( swr ) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors. complete all as specified and directed by engineer in charge. 115 s&f 75mm bore pvc ( swr ) pipe single socketed, in any length with rubber ring joints, fixed to walls as a vent pipe. complete all as specified and directed by engineer in charge. 116 s&f 75mm bore pvc ( swr ) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors. complete all as specified and directed by engineer in charge. 117 s&f 75mm bore pvc ( swr ) bends any radius. complete all as specified and directed by engineer in charge. 118 cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 20 cm girth. complete all as specified and directed by engineer in charge. 119 s&f 75 mm bore pvc ( swr ) vent cowl, complete all as specified and directed by engineer in charge. 120 s&f steel tubes medium grade bore of tube in 15mm galavanised with all fitting laid in trenches, walls, ceiling or laid in floors etc. complete all as specified and directed by engineer in charge. 121 all as per item no 120 above but of size of 20mm bore. complete all as specified and directed by engineer in charge. 122 m&l for chequered cement concrete tiles 20cm x 20cm x 25mm thick over and including 20mm thick screed bed of cement sand mortar 1:4 , set, jointed and pointed in neat cement slurry in floors / path with grey cement and pigment to match. complete all as specified and directed by engineer in charge. 123 excavation in post holes ( or similar holes ) each not exceeding 0.50 cum, and getteing out, returning filing in and ramming earth with broken rubble mixed with earth around in layers not exceeding 25cm, watering etc and removing surplus soil not exceeding 50m and making good surface in loose / soft soil, complete all as specified and directed by engineer in charge. 124 surface excavation not exceeding30cm deep and averaging 15cm deep and getting out in soft / loose soil. complete all as specified and directed by engineer in charge. 125 excavating in trenches in any type of soilnot exceeding 1.5m wide and not exceeding 1.5 m depth for foundation & getting out, complete all as specified and directed by engineer in charge. 126 excavating over areas, not exceeding 1.5m deep and getting out; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out, complete all as specified and directed by engineer in charge. 127 excavating over areas, of depth exceeding 1.5m but not exceeding 3 m and getting out; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out, complete all as specified and directed by engineer in charge. 128 m&l for filling good earth including spreading, leveling, watering and well ramming in layers not exceeding25cm for soft / loose soil, complete all as specified and directed by engineer in charge. 129 returning filling including spreading, leveling, watering and well ramming in layers not exceeding25cm for soft / loose soil, complete all as specified and directed by engineer in charge. 130 removing excavated materials ( soil ) to a distance not exceeding 50m and depositing where directed of a level not exceeding 1.5m above the starting point. complete all as specified and directed by engineer in charge. 131 supply & lay 200mm bore reinforced concrete pipes, class np3, laid and jointed complete with collars, complete all as specified and directed by engineer in charge. 132 m&l for cement concrete 1:3:6 type c 2 using 40mm graded stone aggregate as in concrete bed to drain pipes for bore dia of 200mm including packing under, and haunching against the sides of pipes after they are laid and tested; in, complete all as specified and directed by engineer in charge. 133 m&l for cement concrete type b 1, 1:2:4 ( 12.5mm graded stone aggregate as in surface channels and drains, complete all as specified and directed by engr in charge. 134 m&l for 75mm thick pcc 1:2:4 type b 1 with 20mm graded stone aggregate as in flooring, finished even and rough to receive the topping layer. complete all as specified and directed by engineer in charge. 135 extra for forming fair finished drain or channel not exceeding 45 cm inner girth in cement concrete, using extracement, including forms, moulds, mitred / stopped ends etc. 136 m&l for precast cement concrete type b 1, 1:2:4 as in cover slabs over drain / manholes etc. including necessary formwork, complete all as specified and directed by engr in charge. 137 m&l for construction of sokage well with excavation, in any type of soil, foundation in pcc 1:3:6, wells of honeycombed masonary with top ring of m 25 concrete, including intercepting chamber and screen chamber brick work in cm, rcc cover slabin m 25 / sfrc cover, interconnecting pipe of rcc / dwc complete filled with brick bats, complete of size 2.4m dia x 3m effective depth. complete all as specified and directed by engineer in charge. 138 taking down carefully aluminium point wiring on casing caping / through conduit ( light fan, socket or power ) complete with fittings such as switches, ceiling roses, pendants, regulators, box type tube light fittings, removing the materials from site except fittings etc which shall be reused in the work and making good the disturbed surfaces of walls / ceiling / floors etc complete all as specified and as directed by engineer in charge 139 m & l for point wiring for one light or one fan point controlled by one switch or with one switch and regulator with pvc unsheathed single core multistranded copper conductor ( frls ) cable of size 1.5 sqmm ( nominal area ) in and includingpvc conduit 20 mm bore by cutting chases in wall by cutter and making good the surface in cm 1:3 and to the original specification and cast iron / pressed steel concealed terminal boxes includingproviding3mm thick plastic laminated sheet cover ( hylem ) including one run of pvc insulated copper conductor ( frls ) cable of size 1.5 sqmm with green insulation as earth wire and connected to earth dolly complete all as specified. ( switch / socket outlet to be measured & paid for separately ) . 140 all as per srl item no 139 here in before but for 3 pin socket outlet 5 amps on same board . 141 all as per ser item 139 abovebut for 3 pin socket out let 5 amps on independent board 142 all as per srl item no 139 here in before but for 3 pin socket outlet 15 amps on independent board with pvc unsheathedcopper conductor cable of size 2.50 sqmm including copper earth wire of size 1.50 sqmm and connected to common earth dolly complete all as specified. ( switch / socket to be measured & paid for separately ) 143 supply and fixing in replacement sub main wiring with two single core frls insulated cable with copper conductor stranded and sheathed of size 6 sq mm in and including pvc conduit including 1 x 6 sq mm frls copper earth wire to common earth and connected to earth dolly complete all as specified and directed. 144 supply & fixing switch piano flushtype 5 amp single pole one way. 145 supply & fixing switch piano flushtype 15 amp single pole one way. 146 supply & fixing socket outlet 5 pin 5 amps flush type multipurpose. 147 supply & fixing socket outlet multipurpose 2 in one, 3 pin 5 / 15amps flush type. 148 supply & fixing ceiling rose surface bakelite 65 x 50mmthree terminal complete all as specified and as directed by engineer in charge. 149 supply & fixing fan regulator electronic step type and making connections. 150 supply & fixing angular lamp holder insulated body with back plate suitable for batten fittings including 1 x 9 w led lamp. 151 s & f surface mounting energy saving led tube light fitting, 1x20w, 230v , high efficiency pmma diffuser gives soft glare free light with led tube rode 20 w ( white ) complete with all accessories. 152 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete. 153 supply & fix in replacement ofceiling fan 1200 mm sweep, 240 volts colour opal white make crompton model cool breez or equivalent in bajaj / havells / orient, and connecting up including provision of flexible copper conductor cable from ceiling rose / connector to fan and gi pipe / steel rod, nuts, bolts, clamps etc as required at siteall as specified and directed by engr in charge. 154 supply & fixexhaust fans ac single phase 230 / 240 v of size 450 mm sweep hevy duty with louver ( metal body ) including necessarycutting of wall in sutiable dia for the fixing of exhaust fan and make it in good finish with plaster work completeas specified and directed. 155 supply & fixexhaust fans ac single phase 230 / 240 v of size 300 mm sweep with louver ( metal body ) including necessarycutting of wall in sutiable dia for the fixing of exhaust fan and make it in good finish with plaster work completeas specified and directed. 156 supply and fix water heater storage type, electric, capacity 50 litres.bee 5 star rated. 157 supply and fixingpvc connection cold water pipe 18 long, 15mmdia with brass jem nut and wahser, both side complete all as specified and directed by engineer in charge. 158 all as per ser item no 157 here in before but hot water pipe made of chromium plated brass flexible tubing. 159 supply and fixing stop cock brass of size 15 mm dia. 160 supply and fixing bib cock brass of size 15 mm dia. 161 supply and fixing mcbsingle pole 6 to 32 amps 240 volts. 162 supply and fixing mcb 40 amp spn 240 volt, complete. 163 supply and fixing mcb 63 amp tpn 415 volt, complete. 164 supply & fixing sheet metal enclosures with double door, detachable gland plates flush / mounting for mcb’s fitted with bus bar, earth wire and neutral link, spn12 ways, 240 volts. 165 s&ftpn4 way, vertical type distribution box ( vtpn db ) in double door, ip 54, suitable forflush mounting and surface mounting with 250 a copper bus barfor each ph , two neutral bar, two earthbarwith provn for mccb 100 aas incomer ( w / o mccbs ) andsp / tp as out going complete. 166 supply and fixing mccb 100 amp 4p 415 volt, complete. 167 m & l ofearthing complete with galvanized steel earth plate trode 60cm x 60cm x 6mm thick buried directly in ground vertically in a pit not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below level connected to gi earth wire 4mm diaby means of bolts, nuts and washers ( earth plate covered with charcoal dust and common salt in alternate layers ) gi earth wireprotected by galvanized steel pipe light grade of 15 mm dia upto switch board and connected to main switch board, including provision of 20mm dia gi tubing light grade watering pipe with funnel and wire mesh pcc earth pit ( 1:3:6 ) type c 1 covered with ci cover hinged with frame including excavation and earth work complete all as specified and shown in electrical plate no 5 of ssr part i including testing on completion. 168 disconnecting and taking out old u / s cable of service connection / sub main of any size and type from pole to dbs / main switch complete all as specified 169 excavation in trenches in soft / loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for ltaking out old cable / laying of under ground cable / foundation of poles / stays including segregation of old serviceable bricks complete all as specifiedand directed by engineer in charge. 170 m & l for brick protection using old size sub class b bricks, laid flat dry but adjoining to each other laid lengh wise perpendicular to the axis of cable complete all as specified and directed. 171 supplying, filling in trenches spreading, leveling sand cushioning 8 cm below and 15 cm above the cable for under ground cable complete all as specified & directed. 172 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 2 core. 173 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core. 174 supply and fixing led bldg security light fitting 20 watt powder coated pressure die cast aluminium compact led security light including1.5 mtr long 40 mm bore gi pipe mounting bracket made to shape for fixing on wall with 40 mm x 6 mm flat iron clamp 02 numbers with 16 mm dia bolts, nuts and washersall as specified and directed by engineer in charge.make crompton, product code lsts 20 cdl m or equivalent in bajaj / philips / polycab / havells: contractor shall provide 1 years written manufactures warranty for the led fixture complete including driver from the certified date of completion. 175 m / l for gi pipe light grade galvanized with all fitting laid in trenches / on pole / road crossing of size 40mm 176 m / l for gi pipe light grade galvanized with all fitting laid in trenches / on pole / road crossing of size 50mm 177 cutting the existing 40 / 50mm dia gi / ci pipe line for insertion and with suitable tee and jointing material includingexcavation and earth works all are specified and directed by engr in charge 178 supply and laying in trenches orfixingto wall and ceilingpipe galvanised medium grade 25mm bore including fittings complete allas specifieddirected by engr in charge. 179 supply and laying in trenches orfixingto wall and ceilingpipe galvanised medium grade 25mm bore including fittings complete allas specifieddirected by engr in charge. 180 supply and fixing gate valve flangedcomplete of size 25 mm dia 181 supply and fixing ball brass valves, high pressure, with polythene float and nut complete size 25mm bore....

Punjab State Power Corporation Limited - Punjab

32672970 augmentation of 66 kv line from 220 kv s / s gndtp bathinda to 66kv s / s mes ckt i and ii. 1 tower type a ( d 2o ) normal open type ( cw / tt 3010 r1 ) d 2o + 0m= 05 no. 2 tower type an ( an 2o ) open pit ( cw / tt 3011 r1 ) narrow basean 2o + 0m=02 no. and an 2o + 3m= 02 no. 3 tower type a ( 2 d 2o ) open pit ( cw / tt 3013 r3 ) 2 d 2o + 0m=03 no. , 2 d 2o + 3m=01 no. 4 tower type b ( 2 d 30o ) open pit ( cw / tt 3013 r3 ) 2 d 30o + 0m=01 no. , 2 d 30o + 6m=01 no. 5 transportation and erection of towers complete with all fittings including tack welding ( welding rods to be supplied by the contractor ) & zinc rich paint touching wherever required ( zinc paint to be supplied by the contractor ) installation of danger plates, no. plates, phase plates, ckt plates, bird guard & anti climbing devices etc on labour rate basis ( 66 kv ) d 2o + 0m= 5no , an 2o+0m=2 no., an 2o + 02m=2 no , 6 transportation and erection of towers complete with all fittings including tack welding ( welding rods to be supplied by the contractor ) & zinc rich paint touching wherever required ( zinc paint to be supplied by the contractor ) installation of danger plates, no. plates, phase plates, ckt plates, bird guard & anti climbing devices etc on labour rate basis ( 220 kv ) 2 d 2o + 0m= 03 no , 2 d 2o + 3m= 1no., 2 d 30o + 0m= 1no.2 d 30o + 6m= 01 no, 7 transportation, installation of insulator strings complete with hardware installation & stringing & sagging of conductor 0.2sq” including fixing of conductor accessories for the 66kv d / c line on d / c towers on labour rates basic.= 5.715 ckt km 8 transportation, installation, stringing & sagging of earth wire 7 / 2.24mm at the top of tower including fixing of earth wire accessories as on labour rate basis. = 5.715 km 9 dismentlement and re saggingof conductor 0.4sq” including fixing of conductor accessories for the 220kv s / c line on s / c towers on labour rates basic.= 4.342 ckt km 10 dismentlement and re saggingof earth wire 7 / 3.15 mm at the top of tower including fixing of earth wire accessories as on labour rate basis. = 4.342ckt km 11 pit marking straight tower 12 pit marking angle tower 13 dismantlement of 0.15 sq acsr d / c conductor 14 dismantlement of hrp=04 no. 15 dismantlement of 4rp=06 no. 16 dismantlement of tower 2 s 2=02 no. and2 s 30=01 no., ...

Military Engineer Services - Punjab

32389746 provision of sainik institute at patiala ca no ce chz / pat / t 02 / 2022 23 total amount of sch a sec i ( building works ) lump sum price worked out by the contractor for building works as listed in schedule a part i 2 total amount of sch a sec ii ( site clearance &earth works ) lump sum price worked out by the contractor for site clearance &earth works as listed in schedule a part ii 3 total amount of sch a sec iii ( internal water supply works ) lump sum price worked out by the contractor for internal water supply works as listed in schedule a part iii 4 total amount of sch a sec iv ( internal electrification works ) lump sum price worked out by the contractor for building works as listed in schedule a part iv 5 total amount of sch a sec v ( sewage disposal works ) lump sum price worked out by the contractor for sewage disposal works as listed in schedule a part v 6 total amount of sch a sec vi ( area drainage works ) lump sum price worked out by the contractor for area drainage works as listed in schedule a part vi 7 total amount of sch a sec vii ( security wall, fencing &gate works ) lump sum price worked out by the contractor for security wall, fencing &gate works as listed in schedule a part vii 8 total amount of sch a sec viii ( road, path, culverts and hardstanding works ) lump sum price worked out by the contractor for road, path, culverts and hardstanding works as listed in schedule a part viii 9 total amount of sch a sec ix ( external watersupplyworks ) lump sum price worked out by the contractor for external watersupplyworks as listed in schedule a part ix. 10 total amount of sch a sec x ( ext electric supply works ) lump sum price worked out by the contractor for ext electric supply works as listed in schedule a part x. 11 total amount of sch a sec xi ( ancillary works for installation of summer appliances ) lump sum price worked out by the contractor for ancillary works for installation of summer appliances as listed in schedule a part xi. 12 total amount of sch a sec xii ( open platformworks ) lump sum price worked out by the contractor for open platformworks as listed in schedule a part xii. 13 schedule asection xiii ( misc items of works ) note :this schedule is not pre priced by mes and the pre priced rate indicated as rs 0.00 under col. 5 siginifies this fact only. 14 internal water supply works 15 item no. 01: s & f 15 mm dia cast copper alloy chromium plated angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. 16 internal electric supply works 17 item no. 2 :m& l point wiring complete with 1.5 sqmm ( nominal area ) pvc insulated unsheathed multistranded copper condutor single core cable 1100 volts grade frlsh isi marked drawn through and including heavy duty non metalic pvc conduit, isi marked of not less than 20 mm dia, concealed in wall, roof, etc, with all connected fittings, etc. suitable for mounting modular switches, sockets etc and including frlsh pvc insulated unsheathed multistranded single core copper conductor cable of size 1.5 sq mm green in colour as in earth continuity conductor connected to common earth dolly and all metal parts of fittings as specified and directed for the following: note: switches , sockets, ceiling rose, regulators, modular metal boxes, cover plate etc shall be measured and paid separately. 18 ( a ) one light / fan / bell point controlled by one number one way switch 19 ( b ) one 5 pin socket outlet independent 5 / 6 amps 20 ( c ) one socket outlet 5 / 6 amps on the same board with other switches. 21 ( d ) all as per item 1, but one 6 pin 6 / 16 amps socket outlet independent with 2.5 sqmm size copper conductor cable and1.5 sqmm copper cables as earth wire. 22 item no 3:m& l point wiring complete with 2.5 sqmm ( nominal area ) pvc insulated unsheathed multistranded copper condutor single core cable 1100 volts grade frlsh isi marked drawn through and including heavy duty non metalic pvc conduit, isi marked of not less than 20 mm dia, concealed in wall, roof, etc, two light controlled by one switch with all connected fittings, suitable for mounting modular switches, sockets etc and including frlsh pvc insulated unsheathed multistranded single core copper conductor cable of size 2.5 sq mm green in colour as in earth continuity conductor connected to common earth dolly and all metal parts of fittings as specified and directed.note: switches , sockets, ceiling rose, regulators mosular metalboxes, cover plates etc shall be measured and paid separately. 23 item no 4: s & f white cover plate with frame 12 module 240 volts complete all as specified and directed by the engr in charge. 24 item no 5: blank 25 item no 6: s & f modular metal box 12 module complete all as specified and directed by the engr in charge. 26 item no 7:supply and fixing modular angle holder made with insulated body with back plate for led lamps all as specified and directed by the engr in charge. 27 item no 8 :material andlabour for ceiling rose surface type, 65mm x 50mm two tothree terminals / pvc / polycarbonate, isolated body fixed on pvc block complete all as specified and directed. 28 item no 9 :material andlabour for call bell ding dong ac 230 volt single pole complete all as specified and directed. 29 item no 10:supply and fixingled downlighter 9 watt, retrofit all as specified and directed by engr in charge. 30 item no 11: s&f ledtube light fittings 1 x 18 w, 230v, complete with all accessories internally prewired and including connecting up with twisted flexible pvc copper conductor cable of 23 / 0.0076 from ceiling rose all as directed by engr in charge. 31 item no 12 :supply and fixing mirror light fitting led 10w, 230 v, 2 feet complete all as specified and directed by engr in charge. 32 item no 13 : s&f led building security light, pressure die cast aluminum housing, 25 watts capacity, 240v, ip 65 class, with suitable in built electronic driver complete incld. fixed on a bracket made out of 1.5 mtr long light grade gi pipe 40 mm dia bend to shape as directed fitted on wall at a height not less than 6 mtr from ground with ms clamp, nuts and bolts and washers as required at site and including connecting luminarie to the nearest ceiling rose / junction box with 1.5 sqmm pvc insulated 3 core wire complete all as directed and specified by engr in charge. note cost of all minor spares and jobs required for fixing of light fixture on wall and for electrical connections are deemed to be included in the quoted rate. 33 item no 14 :supply and fixing light fitting led panel 25 w, 230 v, square type surface mounted, injection moulded in thermally conductive engineered plastic fr v0 grade housing, diffuser with high optically efficient material complete all as specified and directed by engr in charge. 34 item no 15 : supply and fixing light fitting led panel 36 w, 230 v, square type surface mounted, injection moulded in thermally conductive engineered plastic fr v0 grade housing, diffuser with high optically efficient material complete all as specified and directed by engr in charge. 35 item no 16 :supply and fixing of 100w led flood light with system lumen efficacy=100 lm / w operating voltage between 140 270vac, driver will comply for 440vac operation ( will sustain for 4 6 hrs continuously ) , driver will have cut off at > 300 vac, power factor more than 0.95%, led cct 5665±355k as per ansi bin, led driving current < 70% of rated maximum forward current, luminaire intergal driver with 5kv surge protection, over load protection, no load protection and bis marking ( r no. for driver ) , driver certiifcation iec64347 2 13 is ( 15885 ) , driver should be concealed under ip66, over all electrical efficency more than 90%, driver electrical efficiency will be > 85% connecting with pvc copper cable of size 3x1 sqmm as per is 10322 atcomplete all as specified and directed. 36 item no 17 :supply and fixing of 60w led high bay light with surface mounted device ( smd ) with multiple led with borosilicate glass lens and acrylic, with aluminum reflector, operating voltage between 140 270vac, power factor more than 0.95%, intergal driver with 5kv surge protection differential mode / coman mode , led cct 5665±355k as per ansi bin, over load protection, no load protection, driver should be concealed under ip66 and bis marking ( r no. for driver ) , driver certiifcation iec64347 2 13 is ( 15885 ) , system lumen >15000, cri>70, over all electrical efficency more than 90%, connecting with pvc copper cable of size 3x1 sqmm complete all as specified and directed. 37 item no 18 :supply and fixing ceiling fan energy efficient, minimum service value ( m3 / minute / watt ) >= 4.5, including modular electronic step type fan regulator flush type fixed on cover sheet, 230 v, 50 hz, 1200 mm sweep confirming to is 374 2019, with all standard accessories as per manufacturers recommendations , with provision of pvc insulated flexible cable frlsh grade 3 core 0.5mm copper conductor 1100 volts grade from porcelain connector / ceiling rose to ceiling fan, complete all as specified and directed. 38 item no. 19: s & f of double door three phase distribution board6 way made out of crca sheets 1.6 mm thick, phosphatised powder coated with copper bus bar 200 amps, 415 v, earth stud, din rail, polymide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box , ground terminal blocks , duly wired with thimbled flame retardant copper conductors and poly layer for protection in all as specified and directed. ( note: mcbs are to be measured and paid for seperately ) 39 item no. 20:s & f sheet metal enclosure mccb tpn distribution board, double door, ip 43 class, including suitable size copper bus bar, 415v, 4 way with shrouded neutral bar, earth bar and including cable ties and suitable size blanks complete all as specified and directed. 40 item no. 21: s&f for flush fixing of sheet metal enclosure mcb spn distribution board, double door, ip 43 class, including suitable size copper bus bar, 240v, 12 way with shrouded neutral bar, earth bar and includingcable ties and suitable size blanks complete all as specified and directed. 41 item no. 22:s&f for flush fixing of sheet metal enclosure mcb spn distribution board, double door, ip 43 class, including suitable size copper bus bar, 240v, 6 way with shrouded neutral bar, earth bar and includingcable ties and suitable size blanks complete all as specified and directed. 42 item no 23 :supply andfix sheet metal enclosure with socket plug top and mcb sp cap 20 amps with a 2 pin, earth plug and socketcomplete all as specified and directed by engr in charge. 43 item no 24 :supply andfix ofmcb sp 6 32 amp 230v complete all as specified and directed. 44 item no. 25:supply and fixingisolator 40 amps, 10 ka, c series 240 v isi marked complete all as specified and directed by engr in charge. 45 item no. 26 : supply and fixing mcb tpn 63 amps, 10 ka c series 240 v isi marked.complete all as specified and directed by engr in charge. 46 item no 27:mccb four pole 125 amp confirming to iec 60947 2 & is – 13947 3thermal magnetic release and adjustable over load setting 0.8 – 1.0 x in and adjustable short circuit setting 6 – 10 x in and rupturing capacity 16 ka at 415 v ac , 50 hz complete all as specified and directed by engr in charge. 47 item no 28 :supply and fixing cable pvc, 2 single core 2.5 sq mm stranded aluminium conductor, 1100 volts grade heavy duty unarmoured 48 item no 29 :s & f exhaust fan of 380mm sweep, metal body, heavy duty, double ball bearing, 1400 rpm, 160 watt, 4 blades, air delivery 3250 m3 / h, suitable for sp 230 / 250 volts, 50 hz ac supply complete with louver shutter including fixing / grouting of frame & louvers in wall using bolts of bolts of suitable size & connecting with and including pvc flexible copper cable of size 23 / 00.0076 three core from ceiling rose to fan complete all as directed.note : cost of opening in wall and grouting of mild steel work shall be deemed include in the lump sum cost of the building. 49 item no 30 :supply andfix environmentalfriendly, ultramodern, energysaving, surface mounted, decorative stud bulkhead edge litled luminaire comprisingofhigh brightness leds ofcapacity 10 watts complete all as specified and directed. 50 road, path & culverts 51 item no.31 : providing, laying, compaction of granular sub base by providing close graded material conforming to specifications i.e grading ii, conforming to clause 401 of mort&h specifications for road and bridge works ( fifth revision ) , mixing in a mechanical mix plant at omc, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller of capacity 8 to 12 tonne to achieve the desired density, 150 mm thick compacted thickness, complete all as specified and directed by engr in charge. 52 item no. 32 : providing, laying, compaction of wet mix macadamconforming to clause 406 of mort&h specifications for road and bridge works ( fifth revision ) , 250 mm thick ( compacted thickness, 125 mm thick in two separate layers ) with mechanically crushed graded stone aggregates and granular material ( size range 53 mm to 0.075 mm ) , grading of aggregatesas per table 400 13 of mort&h specifications for road and bridge works ( fifth revision ) , including premixing the material with water at omc in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub base / base course on well prepared surface and compacting with vibratory roller of 8 to 12 tonne capacity to achieve the desired density , required gradient and camber etc., complete all as specified and directed by engineer in charge.notes:1. the wmm shall be laid in two layers i.e each layer of 125 mm thick ( compacted thickness ) .2. for payment purpose, both layers shall be considered as one unit. 53 item no 33 : preparation ofun surfaced wet mix macadam ( wmm ) surfaces by brushing with wire brushes for re moving caked mud , dust, loose material, foreign material etc., sweeping with power brooms and finally fanning the cleaned surface with air compressors to remove all loose dirt etc. and applying evenly a priming coat on un surfaced wet mix macadam surfaces conforming to clause 502 of mort&h specifications for road and bridge works ( fifth revision ) , with cationic bituminous emulsion ss1 grade, confirming to is 8887 ( latest edition ) @ 7.5 kg per 10 sq metres using primer distributor which shall be self propelled or towed bitumen pressure sprayer complete all as specified and directed by engineer in charge. 54 item no. 34 : providing, laying & compaction of bituminous macadam ( bm ) 50mm compacted thickness conforming to clause 504 of mort&h specifications for road and bridge works ( fifth revision ) , using mechanically crushed stone aggregates and granual material etc. ofgrading ii as per table 500 7 of mort&h specifications for road and bridge works ( fifth revision ) , premixed with bituminous binder, bitumen grade vg 30 @ 3.50% ( percentage by weight oftotal mix ) prepared in batch type hot mix plant of 100 120 tph capacity transported to site by tippers, laid over a previously prepared surface with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density complete all as specified and directed by engineer in charge.notes : ( i ) the contractor shall quote the rate against item considering 3.5% vg 30 bitumen content. job mix formula as permort&h specifications for road and bridge work ( fifth revision ) for bituminous concrete shall be got designed from nit / ctl / govt engg college and shall be got approved from ge in writing well before commencement of work without any financial effect to the department. also the bitumen content shall not be less 3.4% by weight of total mix as per clause 504.2.4 of mort&h specifications ( fifth revision ) . ( ii ) if qty of binder contents is less than the qty as specified in respective items of boq, it shall be adjusted at supply only rates of paving bitumen @ rs 45.00 per kg and if qty of binder contents is more than the qty as specified in respective items of boq no adjustment shall be made. 55 item no. 35 : preparation ofexisting black top surfacesand applying evenly a tack coat conforming to clause 503 of mort&h specifications for road and bridge works ( fifth revision ) , with cationic bituminous emulsion rs1 grade, confirming to is 8887 ( latest edition ) @ 2.5 kg per 10 sq metres using using primer distributor which shall be self propelled or towed bitumen pressure sprayer complete all as specified and directed by engineer in charge. 56 item no. 36 : providing and laying 30 mm thick ( consolidated thickness ) bituminous concrete ( bc ) layer conforming to clause 507 of mort&h specifications for road and bridge work ( fifth revision ) including cost of coarse aggregates, fine aggregates, filler, 5.5% binder ( paving bitumen grade vg 30 ) content by weight of total mix and crushed aggregates of grading 2, anti stripping agent, warm mix additives ( quantity, quality and grade as per the approved job mix formula ) etc, cleaning and pre heating of the mineral aggregate, filler & bitumen to the specific temperature, thoroughly mixing with binder of specified bitumen content, anti stripping agent, warm mix additives as per mix design in hot mix plant of 100 120 tph capacity, carrying the hot mixed materials by means of tipper, trucks, or any other approved and suitable arrangements, laying the hot premixed materials over the prepared surface by means of paver finisher including manual operation as and when required for proper grade, level and camber thorough rolling with power roller 8 to 12 tonnes smooth wheeled, vibratory and tandem roller with necessary hand packing and pinning to give an even surface, including running expense of all plants and machineries, inclusive of proper traffic control during laying to the satisfaction of engineer in charge, required quality control tests at required interval etc complete in all respects complete all as specified and directed by engr in charge. 57 ( itemno 36 contd..... ) notes : ( i ) the contractor shall quote the rate against item considering 5.5% vg 30 bitumen content. job mix formula as per clause no 505.3.3 of mort&h specifications for road and bridge work ( fifth revision ) for bituminous concrete shall be got designed from nit / ctl / govt engg college and shall be got approved from ge in writing well before commencement of work without any financial effect to the department. also the bitumen content shall not be less 5.4% by weight of total mix as per clause 507.2.5 of mort&h specifications ( fifth revision ) . ( ii ) the cost of materials, transportation, job mix formula from lab and testing charges for various tests as required are included in the unit rate quoted by the contractor. ( iii ) cost of filler i.e rock dust, hydrated lime or cement is deemed to be included in unit rate. ( iv ) if qty of binder contents is less than the qty as specified in respective items of boq, it shall be adjusted at supply only rates of paving bitumen @ rs 45.00 per kg and if qty of binder contents is more than the qty as specified in respective items of boq no adjustment shall be made. ( v ) after spreading of mix as per clause 507.4.7 of mort&h specifications entire surface during the operation shall be rolled with road roller 8 10 tonnes ( smooth wheeled ) followed with vibratory road roller of 8 10 tonnes static weight, followed by finish rolling with 6 to 8 tonnes smoooth wheeled tandem roller as per clause no 507.4.8 of mort&h specifications ( fifth revision ) and the cost of the same shall be deemed to be included in the quoted rate. 58 itemno 37 :m & l for precast ( factory casted ) cement concrete kerb stone casted in pcc ( 1:2:4 ) type b 1 using20mm graded stone aggregate with plain or interlocking joints ( as directed ) , making groove in existing road of desired dimension, placing in erect position kerb stone in edging and set and jointed in cement mortar 1:4, making good distrubed surface of ground complete all as specified and directed. 59 item no. 38 :painting lines, dashes, arrows, letters etc on road pavement and the like not exceeding 10 cm wide with thermo plastic paint . 60 item no. 39 :painting lines, dashes, arrows, letters etc on road pavement and the likeexceeding 10 cm wide with thermo plastic paint. 61 item no 40 :delinators of size 700x100x50mm of abs round body fixed with 100mm dia highly reflective reflector, duly uv stablized, in yellow colour complete all as specified. 62 item no. 41:cat eye two way reflective of size 100 x 100 x 18.5mm with pvc body with reflective panels amber / red / whitecompleteall asspecifiedand directed. 63 item no. 42 :m&l bringing approved earth fromoutside md land including cost ofearth& carriage completeall asspecifiedand directed. 64 item no. 43: plain cement concrete ( 1:4:8 ) , type d 2, using 40 mm graded stone aggregates as in concrete bed to drain pipes including packing under and haunching against the sides of pipes for 450 mm bore pipes after the pipes are laid and tested complete all as specified 65 external water supply 66 item no. 44 : m & l cutting existing 150mm bore cast iron water mains at least at two places in position for inserting new tee and inserting cast iron tee of size 150mm x 150mm x 50mm including provision of connecting pieces and other fittings as required including run lead / flanged joints etc complete all as specified and directed. 67 item no.45 : m & l for construction of brick masonary valve pit of size 900 mm x 900mm x 900 mm ( internal size ) thickness of walls shall be 23cm in brick work in cement mortar 1:6 internally plastered in cement mortar ( 1:6 ) and externally plastered in cement mortar ( 1:4 ) over 15cm thick pcc 1:4:8 type d 2 in foundation having 15cm offset around, including 4 cm thick coping in pcc 1:2:4 type b 1 on the top of the brick wall and 3mm thick mild steel sheet cover and angle iron frame of size 40 mm x 40mm x 6mm including provn of suitable hold fasts to hold the frame, locking arrangement and lifting handle, duly painted with two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed. 68 external electrification 69 item no.46 : supply / laying / fixing, jointing, testing and commissioning, lt under ground cable 1100 volts grade xlpe insulated & pvc sheathed cable heavy duty armoured, with multistranded aluminium conductor laid in trenches / ducts / pipes / fixed on walls / poles complete all as specified and directed of following sizes: 70 ( a ) 2 core 16 sqmm 71 ( b ) 3.5 core 25 sqmm 72 ( c ) 3.5 core 50 sqmm ( note : excavation & earth work, gi pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid for seprately under respective items of the schedule. ) 73 item no.47 : supply andlaying sub class ‘b’ old size bricks laid adjacent to each other perpendicular to the direction of cable in trenches for protection of cable all as specified and directed. 74 item no.48 :supply and fixing in truly verticle position, steel tubular swaged pole, type 410 sp 22 ( 8.5 metre long ) complete finial taper plug, bolts, nuts, scerws as specified, ci base plate including drilling holes and painting with two coats of black bituminouspaint externally and internally, providing 30cm wide alternate strips with yellow and black synthetic enamal paint upto 1.2m height from ground level and numbering the pole ( with black and white paint ) , undergruound part of the pole shall be painted with black bituminous paint complete all as specified and as directed.note: excavation, earthwork, pcc foundation shall be measured and paid separately. 75 item no. 50: m&l earthing complete with galvanished steel pipe electrode, 40mm bore medium grade, 2.5 m length , buried directly and preferably vertically in ground with top edge not less than 1.25 m below ground level by drilling hole for electrode, connected to galvanized iron strip 32x6mm earth lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawing and including excavation and earth work, gi pipe light grade 50mm bore for protection of earth lead and connected to continous earth lead on pole / test point, supplying and laying charcoal dust common salt pcc 1:2:4 type b1, chamber and ms angle iron frame 40x40x3mm and rcc cover 40mm thick ( 1:2:4 ) type b1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm c / c both ways with ms handle 12mm dia, pgi / ci funnel and wire mesh, 20mm dia gi pipe medium grade for watering all as shown in electrical plate no 2 on srl page no 496 of ssr part i ( 2009 ) drawing and connection to earth test point including testing complete all as specified and directed.note : ( i ) the cost of earth lead / strip and gi pipe for protection of earth lead / strip upto 7.5m is included in the quoted rate. ( ii ) the cost of excavation, earth work is included in the quoted rate. 76 item no. 51 :m&l for ms junction box made out of 2 mm thick sheet of size 300mm x 250mm x200 mmincluding aluminium busbar single phase with neutral of 63 amp capacity with , mcb sp 10 amp 01 nos for incoming and out going connections including necessary welding work, clamps and mounting on poles etc complete all as specefied and directed. 77 item no. 52 : s&f led street lightip 66 powder coated pressure die castaluminium compact high power led street light fitting25 watts with heat resistant toughned glass complete with all accessoreis watts, including 40 mm light grade gi pipe with 2 nos clamps etc, length of gi pipe not more than 1.5 metre length, for mounting on pole, complete all as specefied and directed. 78 item no. 53 : m & l for dry sand cushioning to pvc under ground cable with screened and washed sand and punning to provide a required cover complete all as specified and directed.note : thickness after punning shall be considered for payment. 79 item no.54 :cable ( with approved colour coading as per is ) with single core frls pvc insulated flexible multistranded copper conductor 1.1 kv grade for security light fitting ( main cable : number of runs indicated below ) along with one run of single core frls pvc insulated flexible multistranded copper conductor 1.1 kv grade for earthing in and including pvc conduits of suitable size, for 2 runs of 2.5 sqmm main cable + 1 run of 1.5 sqmm. 80 item no. 55 : supply , installation, commissionningand testing of out door lt panel board made out of crca sheet 3.15mm thick vermin proof factory madewith angle and aluminium bus bar of capacity 200 amps for 3 phase and neutralwith necessary angle iron 50 x 50 x 6 mm support frame including two coats powder painting over a coat of red oxide primer and grout in pcc complete all as specified and directedcomprising of the following : incoming ( a ) aluminium bus bar of capacity 200 amps for 3 phase with neutral one job ( b ) mccb 415 v, 100a, 4 pole with over load , short circuit and earth fault protection with earth module breaking capacity 25ka 01 nos. ( c ) digital votl meter 0 500 volts square flush mounted with inbuild selector switch 01 nos. ( d ) digital ampere meter square flush mounted with inbuild selector switch 01 nos ( e ) indicator lamps ryb led type 01 set of three. ( e ) ct coils 100 / 5 a 03 nos.out going ( a ) mccb 63 a, 415v , 3 pole with over load short circuit protection, breaking capacity 25 ka 03 nos ( 2+1 ) ( b ) mcb 20 a, 230v , 2pole with over load short circuit protection, breaking capacity 10 ka 01 nos note : ( i ) all mccbs / instruments / mcbs / bus bar shall be housed in a separate housing with on off latches in the housing. ( location sainik institute ) 81 summer appliances / air conditioners 82 item no. 56: supply, install, testing and commissioning ofspilt type air conditionerselectric driven ( 240 volts, single phase, 50 hz supply ) withenergy efficient scroll compressor, working on r 134a or superior environment friendly refrigerant, cordless remote operated, comprising of indoor unit, wall mounted, material of construction of indoor unit abs, power consumption ( max ) 4000 watts, outdoor unit, powder coated, integral refregerant piping, electric connection ( between indoor and outdoor unit located up to a maximum distance of 10 meters ) andcondensate water drainage arrangement etc pressure testing, leak testing, vaccumisation, r 134a gas charging, shifting of indoor and outdoor unit, mounting arrangement of indoor unit with anchor fastner, support rod, vibration isolators complete of following capacity or nearest higher standard size complete of following capacity: 4500 k cal per hour ( 1.5 ton ) .bee 5 star rated complete all as specified & directed. 83 item no:57 : supply, install, testing and commissioning ofspilt type air conditionerselectric driven ( 240 volts, single phase, 50 hz supply ) withenergy efficient scroll compressor, working on r 34a or superior environment friendly refrigerant, cordless remote operated, comprising of indoor unit, wall mounted, material of construction of indoor unit abs, power consumption ( max ) 4000 watts, outdoor unit, powder coated, integral refregerant piping, electric connection ( between indoor and outdoor unit located up to a maximum distance of 10 meters ) andcondensate water drainage arrangement etc pressore testing, leak testing, vaccumisation, r 134a gas charging, shifting of indoor and outdoor unit, mounting arrangement of indoor unit with anchor fastner, support rod, vibration isolators complete of following capacity or nearest higher standard size complete of following capacity 6000 k cal per hour ( 2 ton ) .bee 3 star ratedall as specified and directred by eng in charge. 84 item no 58 : voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 v to 290 v with output voltage stablilized at 230 v with accuracy of+2.5% and of following capacity complete all as specified & directed. 85 ( a ) 4.0 kva 86 ( a ) 5.0 kva 87 item no. 59 :supply andinstallation ofdesert cooler withouter body madeofpgi ( plain galvanised iron ) sheet not less than 1.00 mm thicknessfor fixedpart , thicknessofpgi sheetfor shutter not lessthan 0.80 mmthick, front grillmade ofpgisheet with minimum weight 2.80 kgs. overallouter size not less than 66 cm x 66 cm x 99 cm ( height ) , electricdriven copper wounded fan motor havingnominalair flow capacity 4000 cum per hour andsubmersible pump for requiredflow ofwater ( sigle phase ) , complete all as specified & directed. 88 item no. 60:voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 v to 290 v with output voltage stablilized at 230 v with accuracy of+2.5% and of capacity 2 kva complete all as specified & directed. 89 item no. 61: supply and installed regrigerators, electric driven ( single phase ) , capacity 215 litres frost free complete all as specified & directed. 90 item no. 62 :supply and installed deep freezer hard top 320 ltrs capacity having double door complete all as specified and directed by eic 91 item no63 : supply, installation, testing and commissioning of water cooler, having water storage chamber of stainless steel, electric driven ac single phase, 230 volts, 50 hz having approx storage capacity of 80 ltrs and nominal cooling capacity of 40 ltrs per hour complete all as specified and as directed by engineer in charge. 92 item no.64 :m&l for heavy duty pvc stands for placing / staging of water coolers and refrigirators of propersizes complete all as specified & directed....

Punjab State Power Corporation Limited - Punjab

31551710 shifting of 66kv chabal tarn taran hrp line in the premises of guru nanak nursing college ( hrp no. 44 to 4 rp 46 ) 0.378 km / 0.2 sq inch sc on dc towers ( deposit work ) laying of tower foundations , erection of towers and stringing & sagging of conductor with earth wire for the shifting of 66kv chabal tarn taran hrp line in the premises of guru nanak nursing college ( hrp no. 44 to 4 rp 46 ) 0.378 km / 0.2 sq sc on dc towers ( deposit work ) ...

Punjab State Power Corporation Limited - Punjab

31551704 laying of tower foundations , erection of towers and stringing & sagging of conductor with earth wire for augmentation of ascr conductor of 66kv wadala granthian to udhonangal line from 0.15 sq to 0.2 sq 16.480 km s / c including replacement of 13 no. rusted towers...

Punjab State Power Corporation Limited - Punjab

31520942 procurement of spares for ac plant refrigeration and hydrogen driers at ggsstp rupnagar procurement of spares for ac plant refrigeration and hydrogen driers at ggsstp rupnagar , scroll compressor zr72 380 415v,3 phase, 50 hz, 5.5tr, emerson copeland/lg make , scroll compressor zr144 for11tr lg make ductable split ac, 380 415v, 3 phase, 50hz, make: lg/copeland/ danfoss , dryerssize ½* ½flare 6 long catch all/dry all make danfoss , rotary compressorfor 1.5 ton lg make window ac, 1 phase, 50hz, 220 240v,r 22 gas make: lg/highly/hitachi/ carrier , remote kit including thermostat and pcb for 1.5tr lg make window air conditioner , rotary compressorfor lg make 2tr window ac, r22, 1ph 50hz 220 240 vac, make: lg/ highly/ hitachi/ carrier , running capacitor 10 mfd (tecumesh keltron/epcos) , compressor model: kce 461 hae for 80/120 ltr. water coolers emerson copeland make , compressor model: kce 443 hae for 60/80 ltr. water coolers emerson copleand make , startingcapacitor 6mfd (tecumesh keltron/epcos) , digital thermostat range 10oc to 50oc of make sub zero/danfoss , heavy duty copper tube1/4 , heavy duty copper tube3/8 , reciprocating compressor 2.5 tr 3 phase 380 415 v 50 hz make emerson copeland , fan motor for lg make window ac 1.5 ton, 29kge775t, 220volt, a 1.25 rpm 880 hz 50, ph i volt 149, capacity 10.0/370 volt,cpn h102 00311g , air heater strip rating 2 kw, 230 v ac,29 inch length for package air conditioners , thermostate for water cooler indfoss/ ranuool make , double cappilary filter , dual run capacitor 50x6 mfd epcos , dual run capacitor 50x4 mfd epcos , pcb remote kit including thermo state for voltas window ac 1.5 tr , epcos make dual run capacitor 50+10 mfd +5%, 440 vac, 50/60 hz for lg make 1.5 tr window ac , float valve (brass) completefor water cooler (15mm) , fan motor for voltas make 1.5 ton window ac, 230 v, 50 hz, 1 ph, 1/7 hp, rpm 915/890/865, cap.6.0/440v, model 29sahg058, marathon/ ge , thermally protected scroll compressor unit of capacity 7.5 tr voltage 415, 3 phase voltas/kirloskar/copeland make. , chiller temp, indicator controller , rumptom brazing rod , angle valve 1/4 x ¼” brass , thermostatic expension valve for 5 tr , r 22 gas flare connection type , fan motor along with base and blade brg. type, self lubricated. 1/34hp, 230v,1 phase, 50 hz, 940 rpm ge/marathon make for water cooler , state thimble for window ac size 4 mm heavy duty copper (1 pkt = 100nos.) , single phasing preventor for compressor twin of 5.5 tr lg make ductable split ac model lbuh0750qc , rotary compressor for split ac 1.5 t lg make model 5cw2af5 make lg/highly/ hitachi/ carrier , out door fan motor for split ac 1.5 t lg make , capillary tube 0.64 , hp switch for lg ductable ac 7.5 tr, model 6600l0002a , lp switch for lg ductable ac 7.5 tr, model 6600l0001a , push type cock 15mm water cool , sealed compressor 1.5tr3 415v kch 522 hae for hydrogen drier , refrigerant gas drier 3/8 l5 dn 50 , vaneleaning liq.for a.c. plant cooling coils , starting capacitor 80/100 mfd , copper elbow size 1/2 , copper elbow 5/8 , copper elbow size 7/8 , copper elbow size 1 1/8 , over load protector for kce 461 , over load protector for kce 443 , dryers size 5/8 x 5/8, 6 long catch all/dry all , flair nut brass pin valve , supply lead 3 core with earth wire size 70/76 mm , wall thermometer for measuring temp 10 50/100 degrees. mounting ms case with stove enamelled paint with marking on glass stem , freon bourdon tube pressure gauge 0 300 kg/cm2 dial size 100mm, process connection = bottom entry case material ss 316 , condenser coil for lg make window ac 1.5 tr (copper) , starting capacitor 4mfd , door gasket for water cooler loose , angular thimble brass for window ac 4 mm , air filter model 5230a30001c for lg 7.5 tr ductable ac , pressure gauge 0 300 lbs for hydrogen drier jay pee make capcity 40 m3/hr , compound gauge 30 to 0 to 150 lbs for hydrogen drier jay pee make capcity 40 m3/hr , indoor blower motormodel no. 4681a30016afor lg 7.5 tr ductable ac , expansion v/v 7.5 tr package ac r 22. , accumulator model no. 9901 01 06 , copper pipe ½” , copper elbow size 1 1/2 , copper pipe 1 1/2 , water cooloer body 80/100 including 2 taps , lg condenser window ac 2.0tr , lg condenser split ac 2.0tr...

Punjab State Power Corporation Limited - Punjab

31471515 tender for laying of tower foundations, erection of towers and stringing and sagging of conductor with earth wire for 66kv lines. (1) shifting of 66kv bays at 220kv substation sahnewal (2) 66kv line for m/s srv stel pvt.ltd. unit no.2 vill. bhagwanpura tapping existing 66kv garg acrylic line emanating from 220kv s/s sahnewal 0.510km/0.2sq sc on dc towers. (3) lilo of 66kv line from 220kv pakhowal to raikot for 66kv s/s barmi dc on dc. (4) raising of 66kv line 220kv jagraon to 66kv roomi line from railway track between chowkiman jagraon rly. s/stn. at km 38/5 6 deposit work of railway 0.120km/0.2sqs/ckt. (5) shifting of 66 kv d/ckt. glaspur kanganwal line in the premises of m/s trb exports pvt. ltd. 0.151 km1o.4 sq dc on dc towers. (deposit work) 6) shifting of 66kv chabal tam taran hrp line in the premises of guru nanak nursing college (hrp no.44 to 4 rp 46) 0.378 km/0.2 5q sc on dc towers (deposit work) 7) augmentation of ascr conductor of 66kv wadala g...

Department Of Defence - Punjab

31134075 bids are invited for copper/aluminium point wiring , ceiling/exhaust fan , m&l for pointing wiring , 3 pin 5 amps socket , bell/buzzer point , light point , copper conductor 2.5 sqmm , m&l for point wiring in existing non metalic pvc , copper conductor 2.5 sqmm for 3 pin 15 amps , m&l for point wiring with 4 sqmm , s&f switch , ditto but two way 5 amps , ditto but bell push 5 amps , s&f socket , ditto, but switch 15 amps , s&f socket outlet , m&l ceiling rose , s&f lamp holder , s&f call bell ac, , s & f led light fitting , s&f for submain wiring , s&f for submain wiring , ditto but (three phase) 3x10 sqmm +1x10 sqmm earth wire , s&f sheet metal enclouser (db) triple pole , s&f sheet metal enclouser , double door single pole and netural , single pole and netural 8 way , double door single pole and netural 12 way , ditto but tpn db 4 way 415 volts suitable for mcb tpn , s & f single pole and netural enclouser with a two pin and earth plug and socket complete including one single pole mcb 20 amps , s&f mcb tpn pole 63 amps , s &f mcb spn pole 40 63amps(10ka). , s&f mcb sp 5 32 amps 10 ka , m & l forearthing complete , m & l for double stiff pendants, , m & lfor rigid non metallic pvc , m & l for rigid non metallic , m &l for surface/suspended , m & l for surface/suspended andwall mounted led batten fitting , replacement of ceilingfans , supply and replacement , supply and replace exhaustfan heavy duty , 230 volts, size 450 mm sweep , supply andfix electric water heater storage , led mirror light fittingwith high , energy saving envirenment friendly , xlpeinsulated , galvanized steel earth plate electrode , s&ftpnmccb leygrand 125 a 4 pole 16 ka all as specified anddirected. , s&f mccb tp 32/40 all as specified and directed., temper proof lcd display with polycarbonate cover 3phase 4 wire 415 voltsboq title rewiring to kendriya vidyalya connected items of work total quantity : 8353...

Punjab State Power Corporation Limited - Punjab

30650679 tender for laying of tower foundations, erection of towers and stringing and sagging of conductor with earth wire. construction of 66kv t off 220kv g 1 mandi gobindgarh 66kv mis aman alloy feeder for m/s ambey industries. g.t. road, sihind side mandi gobindgarti 1.752km/o.2 sq sc on dc 8 x, w&z sc towers. (deposit work). construction of 66kv line from existing 66 kv modem feeder emanating from 220kv s/s 6 1 mgg to extend load of m/s parbhat heavy forgmg pvt ltd. ajnah. gt road mgg (deposit work). construction of 66kv t ott tibber kahnuwan rail pole line for 66kv s’s kot dhandhal 5.138 km/o.2 sq sc on dc towers. shting ot 66 ky jalkheri chorwala luie with in the premises of m/s vayu products pvt ltd. (t. no.41 to 42) 0210 km/0.2 sq sc on dc towers. (deposit work)...

Punjab State Power Corporation Limited - Punjab

29928373 laying of tower foundations , erection of towers and stringing & sagging of conductor with earth wire for the construction of 66kv line from behlolpur to haidon bet 7.924 km / 0.2 sq sc on dc towers...

Military Engineer Services - Punjab

29822669 provision of certain sanctioned works at mil stn suranussi under ge kapurthala provn of certain sanctioned works at mil stn suranussi under ge kapurthal a demolition of brick work built in cement mortar , including all quoins arces etc 2 dismantling of asbestos cement ( corrugated, semi corrugated etc ) sheets in roof coverings 3 demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick above or below ground level. 4 dismantling wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets. 5 dismantling, mild steel work of any description not otherwise provided for complete all as specified 6 demolition of cement concrete in roofs, floors ( other than ground floors ) , beams, staircases, landing, chajjas and similar suspended work. 7 dismantling boarding, any description, fixed in any position with screws complete all as specified and directed. 8 taking down cement or cement lime plaster of any description from walls, including racking out joints hacking for key scrubbing down with water etc , complete all as specified. 9 removing old lime wash ( if any ) , hacking for key, raking out joints of old brick work or stone work built in cementmortar; not previously plastered; and scrubbing 10 taking down chowkats or frames with shutters ( without taking off the shutter from the frame ) of area n.exc 1.50 sqm each and removing from site. 11 all as per items no 10 above but area exc 1.50 sqm but n.exc 4.00 sqm 12 m&l for brick work , with sub class b bricks built in cement mortar 1:6 straight or curved on plan exc 6mtr mean radius with old size bricks 13 m&l for 15mm thick cement plastering in cement mortar ( 1:6 ) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified. 14 m&l for 15mm thick cement plastering in cement mortar ( 1:4 ) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified. 15 m&l for 5 mm thick rendering in cement mortar in 1:3 on ceiling finished smooth without using extra cement. 16 m&l for preparing surfaces new of walls and applying two coats oil bound distemper over a coat of alkali primer 17 m&l preparing surfaces new of walls and applying two coats of cement base paint over a coat of alkali primer 18 m&l forpreparation of old plastered or unplastered wall surfaces and applyingone coat of oil bound distemper complete all as specified and directed. 19 m&l for preparation of old painted wooden surfaces of any description over 10 cms width or girth and applying two coat of synthetic enamel paint on wooden surfaces complete. 20 m&l for preparation of old painted steel surfaces of any description over 10 cms width or girth and applying one coat of synthetic enamel paint on steel surfaces complete all as directed. 21 s & f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with j type hooks as specified. 22 s & f pre painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with j type hooks as specified. 23 m&l for 20 25 mm thick machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, over and including 20 mm thick screed or bedding layer in cm 1:4 24 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing servicable tiles to store and rubbish off the premises complete all as specified 25 m&l for non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed inneat cement slurry and pointed in white or coloured cement to match , over and including15 mm thick screed or bedding layer in cm 1:4 26 m&l for glazed ceramic coloured tiles ( 300x200 ) mm & 7mm thick on vertical surfaces of walls set and jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified and directed. 27 m&l for 25mm thick cement concrete type b 0, 1:2:4 using 12.5 mm graded stone agg as in levelling course. 28 m&l for hardcore of broken bricks of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface 29 m&l for 75 mm thick cement concretetype c 2, 1:3:6 as in plinth protection with using 40 mm graded stone aggregate 30 m & l for perforated particle board / tiles 12mm thick for insulation and acoustic purpose 60 x 60cm size fixed with screw to aluminium frame work or staples on snap grid in ceiling complete all as specified and directed by engineer in charge. 31 s & f anodised aluminium snap grid frame work for false ceiling complete all as specified and directed by engr in charge. 32 s&f framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening conforming to gdefe 290 ( gde e 165 ) 33 s & f 35mm thick iind class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in ssr part – i, section – 8, clause 8.24 ( a ) ; supplied and fitted to chowkats all as specified and directed by engineer in charge . 34 s&f300 mm long ordinary helical door spring , fixed to doors with screws 35 s & f mild steel sliding door bolt 300mm long clip type, stove enamelled black with bright bolt not less than 16mm dia complete. 36 s & f mild steel200mm long, barrel tower bolt stove enameled black with bright bolts. 37 s & f mild steel pressed handle oval type stove enameled black of size 150mm. 38 s & f mild steel butt hinges cold rolled of size 100mm medium weight. 39 m&l for preparing new surfaces of steel and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. 40 m&l for preparing new surfaces of wood and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. 41 s&f in replacement 20 mm dia harrison rails mild steel with decorative finish , with fixing brackets , stops, rollers complete all as specified and as directed ( two brackets per 1.5 m length and 08 nos roller per 1.rm ) 42 m / l for 600x450mmbevelled edged mirror of selected quality glassmounted on ac boardfixed to wooden plug with chromium plated screws screedbed in cm ( 1;6 ) 43 s&f in repairs vitreous china urinals, flat back of size 465mmx355mmx 265mm, white with grating and union for discharge pipe including connecting to waste pipe complete all as specified and directed. 44 s&f in repairs pvc flushing cistern, 10 ltr capacity, valve less symphonic action type, low level, with intel, ball valve, float valve and handle including brackets fixed in position, 32 mm dia pvc flush pipe and connection to water mains complete all as specified and directed by engineer in charge. 45 s& f in repair vetrious china wash hand basin flat back550x400mmincluding fixing bracket, pvc waste coupling and waste pipe, cp pillar tap etc all as specified and directed by engineer in charge. 46 taking down gi tubing and connections with all fittings 15 mm bore 47 ditto all as per item 46 above but 20mm bore 48 s&fin repairs15 mm dia gi tubing , medium grade, and connections fixed to wall or ceiling, laid in floor etc complete all as specified and as directed by engineer in charge. 49 s&fin repairs20 mmdia gi tubingand connections fixed to wall or ceiling, laid in floor etc complete all as specified and as directed by engineer in charge. 50 s&f pvc connections 15mm size with ptmt nuts of length 600 mm and all as specified and directed make : prayag. 51 s&f in repair bib taps , 15mm dia cast copper alloy chromium plated , with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferruleand all as specified and directed. 52 s&f in repair stop valves15 mm , cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed. 53 ditto as per item no 52 above but 20 mm dia 54 s&f in repair pillar taps15mm dia , cast copper alloy , with capstan heads , chromium plated , screwed down high pressure , with long screwed shanks and fly nuts , screwed for iron pipe and all as specified and directed. 55 s&fin repairsrotational moulded polythene water storage tanksdouble layer ( cylinder each vertical with closed top ) of capacity 500 itrs, hoisted and fixed in position including pvc float valve 20mm size, specified in ssr pt 1 make : sintex / frontier / polycon complete all as specified and as directed 56 s&fin repairs110 mm dia pvc swr type bends any radius complete all as specified 57 s&fin repairs75 mm dia pvc swr type bends any radius complete all as specified 58 s&fin repairs100 dia ptmt grating doom ( min wt 25 gms ) complete all as specified 59 s&fin repairs100mm borecast ironpipe fixed to wall and jointed with cement joints alla s specified. 60 s&f anodised aluminium frame powder coated with minimum thickness of powder coating 50 micron for doors, windows, ventilators with one or more rebates including joining cleat for fixing, hinges etc. complete all as specified and directed. note: prelaminated partical board and sheet glass / wiremesh shall be measured and paid for separately. make: indal / hindalco / jindal or equivalent as per is. 61 s&f anodised aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, handles, rubber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. 62 s&f aluminium body ( die cast ) body, in door closer hydraulically regulated, designation no 3, universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed 63 s&f 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in squares exc. 0.5 sqm in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and as directed 64 ditto all as item 63 above but exc 0.5 sqm complete all as specified. 65 s & f 40mm thick solid pvc sandwich panel with l mm printed pvc sheet on both sides suitably fixed in aluminium frame work as per specification & drawing 66 s & f aluminium anodised barrel tower bolt of extruded section 150mm long ( isi marked ) . 67 s&f 30mm thick factory made pvc door shutter solid panel consisting of frame made out of ms tubes for top & bottom rails .ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc strip of 20mm width stuck inside with solvent cement for stiles and plain colourpvc sheet for top rail , lock rail &bottom rail on eitherside& as gap insertfor top rail & bottom rail . panellingof plain of plain colurpvc sheet to be fitted in the ms frame welded / sealed to stiles & rails with suitable pvc sheet beading and joined together with solvent cement , etc all as specified and shown on drawings complete all as specified and as directed complete all as specified and directed by engr in charge. 68 m&l for 35 mm thick , factory madeplain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 ( part i ) , kiln seasoned and chemically pressure treated 69 material and labour for 20cmx20cmx25mm thick coloured chequred cement concrete tiles with grey cement and pigment, set, jointedand pointed neat cement slurry in floors , paths and aprons etc laid over and including 15mm thick cement screed or bedding layer in cement mortra ( 1:6 ) complete all as specified and directed by the engineer in charge. 70 matarial and labour for cement concrete ( 1:2:4 ) , type b 1 ( using 20mm graded crushed stone aggregate ) as in coping, benching like works complete all as specified & directed by the engineer in charge. 71 s&f sinks made of stainless steel 1mm thick with drainage board kitchen or laborotory with plugs , washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe , over all size 915mm x 460mm. 72 s&f 3mm thick sheet glass ordinary quality glazing with oil putty in square n.exc0 .50 sqm in each pane 73 s&fgalvanized mild steel wire cloth 0.56 mm dia of wire and average width of aperture 1.18mm 74 hacking out of old broken glass ( any thickness &size quality or description ) from wooden frame glazed with putty or fixed with wooden beading & s&f 3 mm thick sheet glass plain ordinary quality and glazing with oil putty in squarenot exc. 0.50 sqm in each pane complete. 75 disconnecting existing water storage tank of any type and capacity exc. 250 ltrs and not exc. 500 ltrs and removing from site complete. 76 s&f in repair 20mm bore ball valve high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete fixed as in repairs. make : paryag. 77 s&f in repair plastic seat cover white closed pattern with flat bottom and ms chromium plated or aluminum hinges devicefor ewccomplete all as specified. 78 s&f in repair health focet for ewc 79 s&f in repairs vitreous china water closet padestal pattern ( white ) includng p or s trap but excluding fixing bolts, flushing cistern and flush pipe complete all as directed. 80 s&f in repair vitreous china ware water closet orissa pattern including connecting to trap and to flushing pipe anti syphonage pipe etc complete , fixed as in repairs of size 580mm x 440mm complete all as specified. make: hindware / cera / parryware. complete all as specified and as directed 81 s&f in repairs 19mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice laminated as in cupboard, shelves in kitchen etc complete all as specified and directed. 82 s & f hasps and staples with brass knobs 35 40mm dia 83 s & f 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished 84 s & f brass drawer handles, projection drop ( 50mm to 65mm ) on screwed plate complete all as specified. 85 supply & fixing for steel windows 1.25 mm thick box type ( primer coated ) erw hollow p section of size 60mm x 25mm single rebate comprises of skeleton shutter erw sec 50 x 20 mm & 1mm thick and openable leaf consisting two nos sash bar of t section 20x3mm complete welded to frame including cutting holes and making good dismanteled portion in cement concrete ( 1:2:4 ) type b i four nos for each window including following fitting welded to shutter complete glazed window all as specified and as directed by engineer in charge : ( i ) hold fast 150mm long 12 mm x 3mm made to shape 04 nos each window. ( ii ) handle of z section 20 x 25 mm, 100mm long 01 nos each leaf. ( iii ) ms tower bolt 150 mm long 02 nos each leaf. ( iv ) z section 20 x 25mm, 100 mm stopper 01 nos per leaf ( v ) cleat 55 mm long of hollow square 15x20x63mm welded to hinges 01 nos per leaf. ( vi ) ms box type hinges of size 75 x 12 mm 02 nos per leaf. ( vii ) ms guard bars square 12mm dia @10 cm c / c with gi frame fixed to window frame. ( viii ) fabrication and fixingnote : glass shall be measured and paid for separately. 86 ditto all as per item no 85 , but with gauged shutter. 87 s&f 3mm thick sheet glass ordinary quality glazing with oil putty in square n.exc0 .5sqm in each pane 88 s&fgalvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mm 89 dismantling brick tile or terracing tile single layer on roof 90 demolition of mud in roofs , any thickness including plastering and leeping ( weather full thickness removed or part there of ) . 91 supply only integral waterproofing compound 92 applying evenly a tack coat of industrial bitumen 85 / 25 at the rate of1.2 kg per sq.m including cleaning surfaces. 93 preparation of newly plastered surface making surface completely dry and applying a coat of bitumen primer confirming to is :3384 1965 @ 0.30kg / sqm and after drying of primer apply app modified water proofing membrane with non woven polyster reinforcement 3mm thick superior multipolymericweighing not less than 3kg / sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene ( mhhdpe ) film consisting of five layers laid with torching application to the surface over a coat of hot blown bitumen 85 / 25 @1.20 kg / sqm complete and sealing the side as well as end laps ( overlaps should not be less than 10 cm ) complete all as specified and directed by engineer in charge. 94 m&l for 50mmaverage consolidated thickness pcc 1:3:6 type c2with using 20mm graded stone aggregate as in padding on flat roofs etc all as specified and directed. 95 m / l for 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar ( 1:3 ) mixed with 5% of crude oil by weight of cementand pointed flush in cm 1:3 complete all as specified. 96 all as per item 95 above but except tiles. 97 m&l for two coats synthetic enamel paint over new wooden surface over 10 cm width or girth over a coat pink primer complete all as specified 98 m&l for gypsum board 12mm thick in ceiling fixed with screw as per manufacturer instructions 99 s&f 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side 100 s&f mild steel work confirming to fe 290 gde e 165as in wind ties for roof , cutting tops to shape as directed , drilling holes, notching etc complete all as specified 101 s&f in repair pvc swr pipe 110 mm dia single socketed in any length with rubber ring joints laid in trenches etc all as specified 102 ditto all as per item no 101 above but 75 mm dia 103 m&l for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roofs, walls etc fixed with l type or j type or cranked hook bolts. complete all as specified and directed 104 m&l for asbestos cement two piece adjustable plain wing ridge 6mm thick fixed with l type or j type or cranked hook bolts. complete all as specified and directed 105 surface excavation averaging 30 cm deep and getting out in soft / loose soil all as specified and as directed by engr in charge 106 rollling and consolidating formation surafces in cutting with power roller of capacity exc 8 tonne but not exceeding 12 tonne 107 m & l for broken stone or boulder hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled / rammed to a true surfacec omplete all as specified and directed 108 m&l for 100 thick pcc 1:4:8 type d 2 using 40 mm graded aggregate stone as in , filling in sub base and mass concrete completeall as specified and directed 109 m&l for 100 thick pcc 1:2:4 type b 2 using 20 mm graded aggregate stone as in floor and hardstanding completeall as specified and directed 110 removing surplus material, n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point in soft / loose soilcomplete all as specified. 111 m&l for forming contraction joint 65 mm deep x 10mm wide, filled with sealing compound grade a complete all as specified. 112 m & l for forming 12 mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound, grade ‘b’ , complete all as specified and directed byengr in charge 113 m&l for 150mm bore reinforced concrete pipes, class np 2 with one coller per length of pipe complete all as specified and directed. 114 m&l for 15mm thick cement plastering in cement mortar ( 1:4 ) reinforced with wire fabric not exc 4 kg fixed to ventilation duct complete all as specified and directed. 115 s&f in repair of 20mm thick insulating board with fire resistant sheet duly fixed on it and fixing the same on wallscomplete all as specified and directed 116 s&f in repair of rubber bidding 15mm thick on sides of aluminium / wooden door and windows for making air tight complete all as specified and directed. 117 s&f veneered particle boards interior grade 25 mm thick, solid core, general purposes type, with face veneers of typebb, fixed with screws to timber frame work complete as specified. 118 s&f anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long ( 1 no. ) . hinges type b 21 100mm long ( 2 no. ) suitable handle ( 1 no. ) complete all as specified. 119 m & l for 75mm thickfor cement concrete 1:4:8 type d–2 using 40mm graded stone aggregates as in in sub floors, sub bases, floors and pavings etcall as specified and directed byengineer in charge . 120 m&l for sand filling under floors or in foundations including watering and consolidation. 121 s&f in repair 12 mm thick prelaminated particle board, exterior grade, prelaminated on both sides with decorative choice lamination, fixed with screws to timber frame work complete all as specified. 122 s&f 25 mm thick hardwood boarding, supplied & fixed with nails in any situation ( except flooring and skirting ) planed one side with butt joints complete all as specified. 123 m&l for rubber tiles 2.5 mm thick with fabric backing or insert, plain coloured or marbled topping, matt or glossy, laid in floors with approved adhesive including taking down complete all as specified and directed. 124 ditto as item no 123 except rubber tile 125 m&l for three coats of white wash on newly plastered surface including preparation of surface complete all as specified and directed. 126 m&lfor preparationof new plastered surfaces of any description not otherewise describedand applying two coats of cement base painting camouflaging pattern as per designgiven by engineer in charge over a coat of alkali resistant primer on walls including preparation and cleaning the old surface etc complete all as specified and directed. note applicable for item no 126. the design and patternof camouflaging painting with different colour of paints will begiven byengineer in charge the tenderer / contractor shall carryoutwork as per design given byengineer in charge / ge 127 m & l for rcc m 25 for slabs, facia supported on walls, beams, columns and in shelves, the like all as specified and directed by engineer in charge . 128 repair , servicing and overhaulingofrolling shutter gear operated type with chain wheel and hand chain of any size by oiling , greasing to gear box , guide channel , shaft , pully and minor repair to gear box, hood cover, pully etc and replacement of minor parts like spring , pins, lathe etc and including securing guide channel to walls with pcc 1:2:4 type b1 and making good the surfaces with cm ( 1:4 ) and making the rolling shutter functional to the entire satisfaction of the engineer in chargecomplete all as specified. 129 taking down carefully aluminum point wiring on tw batten / in conduit / with conduit ( light / fan / socket or power ) complete and making good the disturbed surfaces of wall / ceiling etc including taking down fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and removing materialfrom site except tube light fittings, fans etc which shall be re usedin work complete all as directed by engineer in charge. 130 material and labour concealed point wiring complete with 1.5 sq.mm ( nominal area ) frls pvcinsulated multi stranded copper conductor in and including heavy duty pvc conduit ( wall thickness 1.6 mm ) including fittings & accessories, with ms concealed terminal boxes with 3mm thick laminated bakelite ( hylum / anchor ) sheet top cover for mounting switch, socket etc for one light / fan / bell point controlled by one switch and regulator with pvc cable copper conductor including 1.5 sqmm solid copper conductor with green frlspvc insulation earth common earth dolly, complete all as specified. make : finolex / havells / plaza / indo asian 131 all as per ser item 130 abovebut for 3 pin socket out let 5 amps on independent board 132 all as per item no 130 above but for 3 pin socket outlet 15 amps with 2.5 sqmm stranded copper conductor pvc unsheathed cable independent including pvc cable copper conductor 1.5 sqmm with green insulator as earth wire with cast iron / pressed steel teminal box all as specified. 133 supply and fixing switch piano flush type 5 amp single pole one way. make : havells / ssk / leader. 134 supply and fixing switch piano flush type 15 amp single pole one way. make : havells / ssk / leader. 135 supply and fixing socket outlet 2 in 1, 3 pin, 5 amps flush type multi purpose. make : havells / ssk / leader. 136 supply and fixing socket outlet 2 in one, 3 pin, 5 and 15amp flush type multi purpose. make : havells / ssk / leader. 137 supply and fixing led tube light fitting 1 x 20 watt, 6000k of make philips / bajaj complete all as specified and directed. 138 supply and fixing ceiling rose surface bakelite 65 x 50mmthree terminals complete all as specified and directed. 139 supply and fixing fan regulator electronic step type and making connection.make : rallison / leader / bajaj 140 supply and fix sheet metal enclosures db’s when mcbs to be used for 240 volts, 8 way spn, double door with 200 amps rated bus bar including earth and neutral link complete all as specified and as directed.make : standard / havells / ship 141 supply and fixmcb spn 40 amps 10ka ‘b’ curve 240 voltsmake indo asian and equal complete all as specified and as directed. 142 supply and fixmcb sp 10 to 30 amps 10ka ‘b’ curve 240 voltsmake indo asian and equalcomplete all as specified and as directed. 143 disconnecting and taking out old unserviceable underground cable of service connection of any size and type from pole to dbs / main switch complete all as specified 144 supply and laying in trences / on pole / wall in protection pipe cable xlpe insulated screened armoured pvc bedded heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 4 core 25 sqmm.make : finolex / havells / plaza / polycab. 145 m & l for replacement of earthing with galvanized iron earth plate electrode 600mm x 600mm, 6mm thick buried directly in ground vertically in a earth pit not less than 2.25mtr below normal ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to gi earth wire 4mm dia by means of gi bolts, nuts, check nuts and washers ( earth plate covered with alternate layers of charcoal dust and common salt 15cm thick ) , gi earth wire protected by gi pipe light grade 15 mm dia upto switch board and connected to main switch board including provision of gi pipe 20 mm dia light grade watering pipe with funnel and wire mesh, all as shown in electrical plate no. 3 of ssr part i, including pcc chamber ( 1:3:6 ) using 20mm graded stone aggregate and ci cover and frame including all necessary excavation and earth work and taking out old earthing complete all as specified and directed. 146 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for laying of cable, foundation of poles , stay and struts etc and getting out in soft / loose soil etc and getting out including trimming of sides all as specified and directed by engineer in charge. 147 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed. 148 removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. 149 material and labour for sand cushioning with a layer of sand 8 cm thick before laying of cable and 15 cm thick after laying of cable in trenches complete all as specified and directed. note: 18cm thickness of sand after punning down shall be measured, recorded & paid. 150 supply and laing old size sub class b bricks alid flat in trenches over the cable with the length of brick perpendicular to lthe direction of cable length adjacent / abutting each other complete all as specified and directed. 151 supply and fixinggi tubing light grade with all fitting laid in trenches , roador wall for cable protection complete all as specified of size 50 mm bore . 152 material and labour for concealed point wiring complete with 1.5 sq.mm ( nominal area ) fr pvcinsulated multi stranded copper conductor in and including heavy duty pvc conduit ( wall thickness 1.6 mm ) including fittings & accessories, with ms module box concealed t with 3mmmodule top cover for mounting switch, socket etc for one light / fan / bell point controlled by one switch and regulator with pvc cable copper conductor including 1.5 sqmm solid copper conductor with green fr pvc insulation earth common earth dolly, complete all as specified.make :finolex / havells / plaza / indo asian 153 ( a ) all as per ser item 152 abovebut for 3 pin socket out let 5 amps on independent board 154 ( b ) all as per ser item 152abovebut for 3 pin socket out let 5 amps on same board 155 all as per srl item no 152 above but for 3 pin socket outlet 15 amps with 2.5 sqmm stranded copper conductor pvc unsheathed cable independent including pvc cable copper conductor 2.5 sqmmwith green insulator as earth wire with cast iron / pressed steel terminal box all as specified. 156 s&fmodular switch6 amp 230 v ac one way, one module complete all as specified 157 s&f modular switch 16 amp 230 v ac one way, with indicator one module complete all as specified 158 s&f modualr socket 6a, 2 / 3 pin two module combined complete all as specified. 159 s&fmodular socket , 6a / 16a, 2 / 3 pin, two module complete all as specified. 160 s&f modularfan regulatorstep type, 120w, 2 module complete all as specified 161 suply and fix white colour plates withframe formodular switchof 01module complete all as specified 162 suply and fix white colour plates withframe formodular switchof 02module complete all asspecified 163 suply and fix white colour plates withframe formodular switchof 03module complete all as specified 164 suply and fix white colour plates withframe formodular switchof 04module complete all as specified 165 suply and fix white colour plates withframe formodular switchof 06module complete all as specified 166 suply and fix white colour plates withframe formodular switchof 08module complete all as specified 167 supply and fixing ceiling rose surface bakelite 65 x 50mmthree terminals complete. make : havells / ssk / leader 168 supply and fixing led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 169 supply and fixing led luminaire 600 mm x 600 mm, 35 / 36 watt, 220 v ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. 170 supply and fixing lamp holder with pvc insulated body fixedplasitc laminated sheet cover shape 3mm thick suitable for batten fitting including 01 no. of led 1 x 15 watt, 230 volts, suitable for 230 volt ac complete all as specified. 171 supply and fixingsingle pole and neutral enclosure with a two pin and earth plug and socket complete with one single mcb 20 amp 172 supply and fixing isolater 63 amps tpn 415 volts.make : standard / ship / havell’s. 173 supply and fixing sheet steel metalenclosure ( db ) triple pole and neutral 4 way 415 , volt with 200 amps rated bus bar make :standard / havells / ship 174 supply, fix, connect and test in replacement , led street light fitting 35 watts ( or above watt ) ip 65 / 66 with pdc aluminium body and toughened glass visor fitted in frame, separate driver compartment provided, secondary optical lens for superior light distribution efficiency >95 lm / w, cct5700k ip65, input voltage from 120 270 v power factor above 0.95 complete fitting including all accessories note : contractor shall provide 1 years written manufactures warranty for the led fixture complete including driver from the certified date of completion. make : polycab cat part no pcgls 01 30 product code pub0502004 and c&s electric cat part no ltess 12 x 2.5 hpled / ls product code indus / 30w / ls ( model indus series ) or equivalent in makes indicated in appendix b of particular specifications complete all as specified and as directednote : contractor shall provide 1 years written manufactures warranty for the led fixture complete including driver from the certified date of completion. 175 supply and fixingceilingfan 1200 mm sweepcompletedwith capacitorcanpyand down rod includingflexibletwin corecopper ( 23 / 0. 0076 ) with provisionof ceiling rose / connectorto fan all as specified . 176 s & f propeller type ac ventilating fans 300 mm sweep pvc body ( exhaust fan ) with louver shutter complete including m & l for providing / cutting the roundhole of required size in wall finishing the same suppply and grouting the ragged bolts in wall fixig the frame on the exhaust side ( outer surface of the wall ) and connecting with and including pvc insulated three core 14 / 0.006 copper cable rubber insulated from ceiling rose to exhaust fan motor and writting mes nowith black synthetic enamel paint 2.0 cm high complete all as specified and directed. 177 supply, laying and testing cable xlpe insulated screened, pvc bedded, galvanised steel strip or wire armoured electric cables ( heay duty 1100 volts grade with stranded aluminium conductor of size 10 sqmm 4 core 178 supply, laying and testing cable xlpe insulated screened, pvc bedded, galvanised steel strip or wire armoured electric cables ( heay duty 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core 179 supply, laying and testing cable xlpe insulated screened, pvc bedded, galvanised steel strip or wire armoured electric cables ( heay duty 1100 volts grade with stranded aluminium conductor of size 70 sqmm 3.5 core 180 material and labour in replacement for earthing complete with copper earth plate electrode 600mm x 600mm x 3.15 mm thick buried directly in ground earth pit not less than 2.25 mtr below normal gl with the top edge of the plate not less then 1.5 mtr below the normal gl connected to 20x3mm copper strip as earth lead by means of bolts, nuts, check nuts and washer of brass and protected by 40 mm gi pipe ( light grade ) and watering pipe 20mm bore gi pipe ( light grade ) including gi wire meshed funnel and chamber pcc ( 1:4:8 ) type d2 using 40mm grade stone aggregate, coping shall be ( 1:3:6 ) type ci using 20mm stone aggregate with rcc 1:2:4 type b1 ( using 20mm graded stone aggregate ) pit cover re inforced with 8mm dia at 80mm c / c both way in lieu of ci pit cover with angle iron frame, including excavation and earth work in any type of soil and removal of surplus soil of earth complete all as shown in electrical plate of ssr part i and as specified including charcoal dust, common salt complete and earth lead connected to earthing test point all as specified and testing of earthing on completion. note 1. the unit rate includes for protection pipe and copper strip 20x3mm from top of earth plate up to 7.5 meter above ground level. 181 supply and fixing round shape 12 watt 220 volts ac recessed type with high efficiency pmma diffuser soft glare free light complete with drivers, holders, led lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complet 182 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complet 183 supply and fix led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size 184 supply and fixing exhaust fan 300 mm sweep 900 rpm, heavy duty, ac single phase 230 / 240 volts, metal body with louver shutters including making circular hole in existing wall to accommodate exhaust fan and necessary civil work and making good the disturbed surface complete all as specified and directed. 185 m&l for sub main wiring with two runs of single core pvc insulated, unsheathed copper condutor, multi stranded cable of size 6.00 sqmm 1100 volts grade drawn pvc concealed conduit of size19 / 20 mm ( isi marked ) including pvc accessories complete incl cutting and chasing and making good etc including one run of 6.00 sqmm single core copper conductormulti stranded pvc insulated, unsheathed cable as earth wire continuity conductor complete all as specified and directed by engineer in charge. note : two run of 6.00 sqmm cable one run of 6.00 sqmm cable as earth continuity conductor and one run of pvc conduit shall be measured & paid as one unit. ) note : two run of 6.00 sqmm cable and one run of 6.00earth wire & 20 mm pvc conduit shall be measured as one unit length 186 all as per above item no 185 butcable size of 4 sqmm...

Punjab State Power Corporation Limited - Punjab

29465703 laying of tower foundations , erection of towers and stringing & sagging of conductor with earth wire for theaugmentation of 0.2 sq acsr with 0.4 sq acsr of 66kv allied recyling feeder emanating from 220kv s / s kohara for the extension of load m / s sharmanji yarns pvt. ltd. lakhowal road, kohara, 0.267km / 0.4 sq sc on m. ckt. towers....

Punjab State Power Corporation Limited - Punjab

29465701 laying of tower foundations , erection of towers and stringing & sagging of conductor with earth wire for augmentation of ascr conductor of 66kv wadala granthian to udhonangal line from 0.15 sq to 0.2 sq 16.480 km s / c including replacement of 13 no. rusted towers...

Punjab State Power Corporation Limited - Punjab

29462176 tender for laying of tower foundations, erection of towers and stringing and sagging of conductor withd earth wire for the augmentation of of 0.2 sq. acsr with 0.4 sq acsr of 66kv allied recyling feeder emanating , laying of tower foundaitons, erection of towers and stringing and saging of conductor with earth wire for augmentation of acsr conductor of 66kv wadala granthian to udhonangal line from 0.15 sq to 0.2 sq. 16.480 km / including replacement of 13 no. rusted towers...

Department Of Defence - Punjab

29430818 bids are invited for split ac 2ton supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and plasma filterfor better indoor air quality with minimum 3 star ratingof capacity 2.0ton.make: voltas/blue star/equivalent. , enclsoure spn s & f single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb 20 ampsmake: standard/havells model no: dhdcusn020 , stabilizer s & f voltage stabilizer suitable for 2ton split ac all as specified.make: v guard, model no.vg 500, 15a, 170v 270v , point wiring m & l sub main wiring with two single core 6.0 sqmm and one single core of 6.0 sqmm as earth wire with multi stranded copper conductor cable pvc ( frls) insulated unsheathed cable 1100 volts grade drawn through in non metallic rigid ( isi ) pvc conduit of size 25 mm dia and the conduits accessorioes as in repair complete incluiding making good the distrubed surface to match the existing surface complete allas specified and directed. , water heater supply and fix water heater storage type, electric,capacity 25 litres.bee 5 star rated make : bajaj/crompton/havells/ model no ghwamgsib025 , window ac 1.5ton supply andfix room window type air conditioner electric driven (single phase) cooling capacity 4500 k cal per hour complete with cordless remote control unit and with in built air ioniser and plasma filterfor better indoor air quality with minimum 3 star ratingof capacity 1.5 ton. make : voltas/blue star/equivalent. , split ac 1.5ton supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 3 star rating and eer 3.2 of capacity 1.5ton. make : voltas/blue star/equivalent. , watercooler supply, installation, commis sioning of water cooler 40/80 ltrs capacity, partially stainless steel, electric driven single phase having approx storage capacity 80ltrs and nominal cooling capacity of 40 ltrs per hourcomplete with all necessary water connection, electrical connection and required fixing arrengement all as specified and directed.make: blue star/voltasequivalent. , voltage stabilizer supply & fix voltage stabilizer for automatic operation, single phase for water cooler & designed for input variation on between 150 v to 280v with output voltage stabilizer at 230v with accuracy of + 2.5% and capacity 2/3 kva, make: v guard model no vg 150 , desert cooler supply, installation, commissioning and testing of desert cooler eelctirc driven (single phase) having nominal air flow capacity of 4000cum per hour, 230 volts, 1350 rpm, multi speed control and water tank capacity 51 ltrs, galvanised iron pray painted body with necessary electrical connection and required fixing arrengements all as specified and directed.make: crompton/equivalent. , refrigerator supply and fix refrigerator, electric driven (single phase) capacity up to 190 ltrs bee 3 star rated complete with inbuilt stabilizer for suitable capacity all as specified and directedmake: blue star/godrej/voltas/equivalent. , exhaust fan supply and fix metal body exhaust fans 230 volts single phase oscillating 300mm sweep with blades, louvers and framemake: crompton/havells/equivalent. total quantity : 2...

Punjab State Transmission Corporation Limited - Punjab

29413783 for procurement of hydraulics crimping jointing machine and d sackle for maintenance of 400 kv transmission lines procurement of hydraulic crimping conductor jointing machine with one die set for each type of conductor and earth wire 01 die set includes dies for both aluminum and steel and d shackle , hydraulic crimping jointing machine , hydraulic crimping / conductor jointing machinewith one die set for each type of conductor and earth wire ( 01 die set includes dies for both aluminium and steel reqd. as per annexure c ) , d shackle ( reqd. as per annexure c ) , 4.5 ton capacity , 9.5 ton capacity , 12 ton capacity...

Ministry Of Home Affairs - Punjab

29260396 bids are invited for rewiring of quarters 01 rewiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable and 1.5 sq.mm frls pvc insulated copper conductor single core cable as earth wire in existing surface / recessed steel / pvc conduit including dismantling as required.:group a ( anchor / plaza / havells / polycab / national / finolex / rr cables / isi mark ) , rewiring of quarters 02 rewiring for light point / fan point / exhaust fan point / call bell point with 2.5 sq.mm frls pvc insulated copper conductorsingle core cable and 1.5 sq.mm frls pvc insulated copperconductor single core cable as earth wire in existing surface / recessed steel / pvc conduit including dismantling as required. ( anchor / plaza / havells / polycab / national / finolex / rr cables / isi mark ) , rewiring of quarters 03 supplying and fixing following piano type switch / socket on theexisting switch box / cover including connections etc. asrequired.:5 / 6 amps switch ( anchor / cona / kinjal / isi mark / havells reo / gratewhite ) , rewiring of quarters 04 supplying and fixing following piano type switch / socket on theexisting switch box / cover including connections etc. asrequired.:15 / 16 a switch ( anchor / cona / kinjal / isi mark / havells reo / gratewhite ) total quantity : 1...

Punjab State Transmission Corporation Limited - Punjab

29204095 specification and general instructions for design manufacture testing supply delivery of sub station busbar hardware fittings bolted type suitable for acsr zebra moose twin zebra moose earth wire clamps specification and general instructions for design manufacture testing supply delivery of sub station busbar hardware fittings bolted type suitable for acsr zebra moose twin zebra moose earth wire clamps , single suspension bolted type fitting for acsr zebra , single suspension bolted type fitting for acsrtwin zebra , single suspensionbolted type fitting for acsrmoose , double suspension bolted type fitting for acsrzebra , double suspension bolted type fitting for acsr twin zebra , double suspension bolted type fitting for acsr twin moose , single tension bolted type fitting for acsrzebra , single tension bolted type fitting for acsr twin zebra , double tension bolted type fitting for acsr zebra , double tension bolted type fitting for acsrtwin zebra , double tension bolted type fitting for acsrtwin moose , pg clamp for acsrzebra , pg clamp for acsrmoose , bus bar spacers for acsr zebra , bus bar spacers for acsr moose , tee clamp for acsr zebra , tee clamp for acsr moose , isolator double groove clamp for acsrzebra , c wedgefor acsr zebra , c wedgefor acsrmoose , double groove post insulator clamp for zebra , isolator quad groove clampzebra , earthwire clampsfor 7/3.15mm...

Northern Railway - Punjab

28560239 supply of come along clamps for earth wire (19/2.5 mm) galvanized steel as per drg no. re/33/p/550 (make im or similar)come along clamps for earth wire (19/2.5 mm) galvanized steel as per drg no. re/33/p/550 (make im or similar),come along clamps for earth wire (19/2.5 mm) galvanized steel as per drg no. re/33/p/550(make im or similar)...

Punjab State Power Corporation Limited - Punjab

28535689 laying of tower foundations , erection of towers and stringing and sagging of conductor with earth wire for the construction of 66kv t off fatehgarh churian majitha line for 66 kv sub station thatha...

Military Engineer Services - Punjab

28487820 provision of sainik institute at patiala 1 total amount of sch a sec i ( building works ) lump sum price worked out by the contractor for building works as listed in schedule a part i 2 total amount of sch a sec ii ( site clearance & earth works ) lump sum price worked out by the contractor for site clearance & earth works as listed in schedule a part ii 3 total amount of sch a sec iii ( internal electrification works ) lump sum price worked out by the contractor for building works as listed in schedule a part iii 4 total amount of sch a sec iv ( internal water supply works ) lump sum price worked out by the contractor for internal water supply works as listed in schedule a part iv 5 total amount of sch a sec v ( sewage disposal works ) lump sum price worked out by the contractor for sewage disposal works as listed in schedule a part v 6 total amount of sch a sec vi ( area drainage works ) lump sum price worked out by the contractor for area drainage works as listed in schedule a part vi 7 total amount of sch a sec vii ( road / path / culvert works ) lump sum price worked out by the contractor for road / path / culvert works as listed in schedule a part vii 8 total amount of sch a sec viii ( security wall / fencing works ) lump sum price worked out by the contractor for security wall / fencing works as listed in schedule a part viii 9 total amount of sch a sec ix ( external electrification works ) lump sum price worked out by the contractor for external electrification works as listed in schedule a part ix. 10 total amount of sch a sec x ( external water supply works ) lump sum price worked out by the contractor for external water supply works as listed in schedule a part x. 11 total amount of sch a sec xi ( summer appliances works ) lump sum price worked out by the contractor for summer appliances works as listed in schedule a part xi. 12 total amount of sch a sec xii ( open platform works ) lump sum price worked out by the contractor for open platform works as listed in schedule a part xiii. 13 schedule asection xiii ( misc items of works ) note : this schedule is not pre priced by mes and the pre priced rate indicated as rs 0.00 under col. 5 siginifies this fact only. 14 internal electric supply works 15 item no. 1 :m& l point wiring complete with 1.5 sqmm ( nominal area ) pvc insulated unsheathed multistranded copper condutor single core cable 1100 volts grade frlsh isi marked drawn through and including heavy duty non metalic pvc conduit, isi marked of not less than 20 mm dia, concealed in wall, roof, etc, with all connected fittings, etc. suitable for mounting modular switches, sockets etc and including frlsh pvc insulated unsheathed multistranded single core copper conductor cable of size 1.5 sq mm green in colour as in earth continuity conductor connected to common earth dolly and all metal parts of fittings as specified and directed for the following: nnote: switches , sockets, ceiling rose, regulators, modular metal boxes, cover plate etc shall be measured and paid separately. 16 ( a ) one light / fan / bell point controlled by one switch 17 ( b ) one 5 pin socket outlet independent 5 / 6 amps 18 ( c ) one socket outlet 5 / 6 amps on the same board with other switches. 19 ( d ) one 6 pin 6 / 16 amps socket outlet independent with 2.5 sqmm size copper conductor cable and 1.5 sqmm copper cables as earth wire. 20 item no 2: m& l point wiring complete with 2.5 sqmm ( nominal area ) pvc insulated unsheathed multistranded copper condutor single core cable 1100 volts grade frlsh isi marked drawn through and including heavy duty non metalic pvc conduit, isi marked of not less than 20 mm dia, concealed in wall, roof, etc, two light controlled by one switch with all connected fittings, suitable for mounting modular switches, sockets etc and including frlsh pvc insulated unsheathed multistranded single core copper conductor cable of size 2.5 sq mm green in colour as in earth continuity conductor connected to common earth dolly and all metal parts of fittings as specified and directed. nnote: switches , sockets, ceiling rose, regulators mosular metal boxes, cover plates etc shall be measured and paid separately. 21 item no 3: s&f white cover plate with frame 12 module 240 volts andcomplete all as specified and directed by the engr in charge. 22 item no 4: s&f modular metal box 8 module and complete all as specified and directed by the engr in charge. 23 item no 5: s&f modular metal box 12 module and complete all as specified and directed by the engr in charge. 24 item no 6: supply and fixing modular angle holder cat pat no 33958 of anchor or equivalent makes with insulated body with back plate for led lamps all as specified and directed by the engr in charge. 25 item no 7: supply and fixing led downlighter 9 watt, retrofit all as specified and directed by engr in charge. 26 item no 8: s&f led tube light fittings 1 x 18 w, 230v, complete with all accessories internally prewired and including connecting up with twisted flexible pvc copper conductor cable of 23 / 0.0076 from ceiling rose all as directed by engr in charge. 27 item no. 9: s&f of double door three phase distribution board 6 way made out of crca sheets 1.6 mm thick, phosphatised powder coated with copper bus bar 200 amps, 415 v, earth stud, din rail, polymide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box , ground terminal blocks , duly wired with thimbled flame retardant copper conductors and poly layer for protection in all as specified and directed. ( note: single phase mcbs are to be measured and paid for seperately ) n 28 item no. 10: s&f sheet metal enclosure mccb tpn distribution board, double door, ip 43 class, including suitable size copper bus bar, 415v, 4 way with shrouded neutral bar, earth bar and incld. cable ties and suitable size blanks, including taking down of existing sheet metal enclosure complete all as specified and directed. 29 item no. 11: supply and fixing in replacement isolator 40 amps, 10 ka, c series 240 v isi marked complete all as specified and directed by engr in charge. 30 item no. 12: s&f for flush fixing of sheet metal enclosure mcb spn distribution board, double door, ip 43 class, including suitable size copper bus bar, 240v, 12 way with shrouded neutral bar, earth bar and incld. cable ties and suitable size blanks, including taking down of existing sheet metal enclosure complete all as specified and directed. n 31 item no. 13: s&f for flush fixing of sheet metal enclosure mcb spn distribution board, double door, ip 43 class, including suitable size copper bus bar, 240v, 6 way with shrouded neutral bar, earth bar and incld. cable ties and suitable size blanks, including taking down of existing sheet metal enclosure complete all as specified and directed. n 32 item no. 14 : supply and fixing mcb tpn 63 amps, 10 ka c series 240 v isi marked.complete all as specified and directed by engr in charge. 33 item no 15: supply and fixing thermal magnetic adjustable type mccb 125 amps , 16 ka, c series 415. v isi marked.complete all as specified and directed by engr in charge. 34 item no 16 : supply and fixing cable pvc, 2 single core 2.5 sq mm stranded aluminium conductor, 1100 volts grade heavy duty unarmoured 35 item no 17 : supply and fixing mirror light fitting led 10w, 230 v, 2ft all as per crompton make cat no. lcl 14 cdl or equivalent makes mentioned in tender documents, complete all as specified and directed by engr in charge. 36 item no 18 : s&f led building security light, pressure die cast aluminum housing, 25 watts capacity, 240v, ip 65 class, with suitable in built electronic driver complete incld. fixed on a bracket made out of 1.5 mtr long med grade gi pipe 40 mm dia bend to shape as directed fitted on wall at a height not less than 6 mtr from ground with ms clamp, nuts and bolts and washers as required at site and incld. connecting luminarie to the nearest ceiling rose / junction box with 1.5 sqmm pvc insulated 3 core wire complete all as directed and specified by engr in charge of make crompton greaves or equivalent in philips / wipro. note cost of all minor spares and jobs required for fixing of light fixture on wall and for electrical connections are deemed to be included in the quoted rate. 37 item no 19 : suppy and fixing exhaust fan heavy duty with louvers of size 380mm sweep, 900 rpm 230 volts single phase ac supply complete with, bolt, nuts and washers, suitably embedded in the wall including making suitable opening and provisioning of flexible cord copper of size 23 / 0.0076 from ceiling rose to exhaust fan for giving connection complete all as specified and directed by engineer in charge. 38 item no 20 : supply only sheet metal enclosure with socket plug top and mcb sp cap 20 amps with a 2 pin, earth plug and socket complete all as specified and directed by engr in charge. 39 item no 21 : supply and fixing in light fitting led panel 25 w, 230 v, round type surface mounted, injection molded in thermally conductive engineered plastic fr v0 grade housing, diffuser with high optically efficient material all as per crompton cat part no.: lcrp 20 cdl or equivalent model of makes mentioned in tender documents, complete all as specified and directed by engr in charge. 40 item no 22 : supply and fixing in light fitting led panel 36 w, 230 v, round type surface mounted, injection molded in thermally conductive engineered plastic fr v0 grade housing, diffuser with high optically efficient material all as per crompton cat no.: lcrp 20 cdl make or equivalent or equivalent makes mentioned in tender documents, complete all as specified and directed by engr in charge. 41 item no 23 : supply and fixing of 100w led flood light with system lumen efficacy=100 lm / w operating voltage between 140 270vac, driver will comply for 440vac operation ( will sustain for 4 6 hrs continuously ) , driver will have cut off at > 300 vac, power factor more than 0.95%, led cct 5665±355k as per ansi bin, led driving current < 70% of rated maximum forward current, luminaire intergal driver with 5kv surge protection, over load protection, no load protection and bis marking ( r no. for driver ) , driver certiifcation iec64347 2 13 is ( 15885 ) , driver should be concealed under ip66, over all electrical efficency more than 90%, driver electrical efficiency will be > 85% connecting with pvc copper cable of size 3x1 sqmm as per is 10322 at complete all as specified and directed. 42 item no 24 : supply and fixing of 60w led high bay light with surface mounted device ( smd ) with multiple led with borosilicate glass lens and acrylic, with aluminum reflector, operating voltage between 140 270vac, power factor more than 0.95%, intergal driver with 5kv surge protection differential mode / coman mode , led cct 5665±355k as per ansi bin, over load protection, no load protection, driver should be concealed under ip66 and bis marking ( r no. for driver ) , driver certiifcation iec64347 2 13 is ( 15885 ) , system lumen >15000, cri>70, over all electrical efficency more than 90%, connecting with pvc copper cable of size 3x1 sqmm complete all as specified and directed. 43 item no 25 : supply, installation, connecting and testing of ceiling fan electric single phase 230 volts ac of sweep 1200mm having service value more than 4, complete with mounting arrangment in ceiling such as down rod 600mm, hooks, clamps, nuts, bolts and washers etc complete all as specified and directed. 44 item no 26 : material and labour for ceiling rose surface type, 65mm x 50mm two to three terminals / pvc / polycarbonate, isolated body fixed on pvc block complete all as specified and directed. 45 item no 27 : supply and fix of mcb sp 6 32 amp 230v complete all as specified and directed. 46 item no 28 : material and labour for call bell ding dong ac 230 volt single pole complete all as specified and directed. 47 item no 29 : supply and fix environmental friendly, ultra modern, energy saving, surface mounted, decorative stud bulk head edge lit led luminaire comprising of high brightness leds of capacity 10 watts complete all as specified and directed. 48 road, path & culverts 49 item no 30 : delinators of size 700x100x50mm of abs round body fixed with 100mm dia highly reflective reflector, duly uv stablized, in yellow colour complete all as specified. 50 item no. 31: cat eye two way reflective of size 100 x 100 x 18.5mm with pvc body with reflective panels amber / red / white complete all as specified and directed. 51 item no. 32: supply only sand for sand cusioning under interlocking paver block complete all as specified and directed. 52 item no. 33 : m&l bringing approved earth from outside md land including cost of earth & carriage complete all as specified and directed. 53 item no. 34 :painting lines, dashes, arrows, letters etc on road pavement and the like not exceeding 10 cm wide with thermo plastic paint . 54 item no. 35 :painting lines, dashes, arrows, letters etc on road pavement and the like exceeding 10 cm wide with thermo plastic paint. 55 item no.36 : providing, laying, compaction of granular sub base by providing close graded material conforming to specifications i.e grading ii, conforming to clause 401 of mort&h specifications for road and bridge works ( fifth revision ) , mixing in a mechanical mix plant at omc, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller of capacity 8 to 12 tonne to achieve the desired density, 150 mm thick compacted thickness, complete all as specified and directed by engr in charge. 56 item no. 37 : providing, laying, compaction of wet mix macadam conforming to clause 406 of mort&h specifications for road and bridge works ( fifth revision ) , 250 mm thick ( compacted thickness, 125 mm thick in two separate layers ) with mechanically crushed graded stone aggregates and granular material ( size range 53 mm to 0.075 mm ) , grading of aggregates as per table 400 13 of mort&h specifications for road and bridge works ( fifth revision ) , including premixing the material with water at omc in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub base / base course on well prepared surface and compacting with vibratory roller of 8 to 12 tonne capacity to achieve the desired density , required gradient and camber etc., complete all as specified and directed by engineer in charge. nnotes: n1. the wmm shall be laid in two layers i.e each layer of 125 mm thick ( compacted thickness ) . n2. for payment purpose, both layers shall be considered as one unit. 57 item no 38 : preparation of un surfaced wet mix macadam ( wmm ) surfaces by brushing with wire brushes for re moving caked mud , dust, loose material, foreign material etc., sweeping with power brooms and finally fanning the cleaned surface with air compressors to remove all loose dirt etc. and applying evenly a priming coat on un surfaced wet mix macadam surfaces conforming to clause 502 of mort&h specifications for road and bridge works ( fifth revision ) , with cationic bituminous emulsion ss1 grade, confirming to is 8887 ( latest edition ) @ 7.5 kg per 10 sq metres using primer distributor which shall be self propelled or towed bitumen pressure sprayer complete all as specified and directed by engineer in charge. n 58 item no. 39 : providing, laying & compaction of bituminous macadam ( bm ) 50 mm compacted thickness conforming to clause 504 of mort&h specifications for road and bridge works ( fifth revision ) , using mechanically crushed stone aggregates and granual material etc. of grading ii as per table 500 7 of mort&h specifications for road and bridge works ( fifth revision ) , premixed with bituminous binder, bitumen grade vg 30 @ 3.50% ( percentage by weight of total mix ) prepared in batch type hot mix plant of 100 120 tph capacity transported to site by tippers, laid over a previously prepared surface with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density complete all as specified and directed by engineer in charge. nnotes : ( i ) the contractor shall quote the rate against item considering 3.5% vg 30 bitumen content. job mix formula as per mort&h specifications for road and bridge work ( fifth revision ) for bituminous concrete shall be got designed from nit / ctl / govt engg college and shall be got approved from ge in writing well before commencement of work without any financial effect to the department. also the bitumen content shall not be less 3.4% by weight of total mix as per clause 504.2.4 of mort&h specifications ( fifth revision ) . n ( ii ) if qty of binder contents is less than the qty as specified in respective items of boq, it shall be adjusted at supply only rates of paving bitumen @ rs 45.00 per kg and if qty of binder contents is more than the qty as specified in respective items of boq no adjustment shall be made. 59 item no. 40 : preparation of surfaces and applying evenly a tack coat conforming to clause 503 of mort&h specifications for road and bridge works ( fifth revision ) , with cationic bituminous emulsion rs1 grade, confirming to is 8887 ( latest edition ) @ 2.5 kg per 10 sq metres using using primer distributor which shall be self propelled or towed bitumen pressure sprayer complete all as specified and directed by engineer in charge. n 60 item no. 41 : preparation of existing black top surfaces and applying evenly a tack coat conforming to clause 503 of mort&h specifications for road and bridge works ( fifth revision ) , with cationic bituminous emulsion rs1 grade, confirming to is 8887 ( latest edition ) @ 2.5 kg per 10 sq metres using using primer distributor which shall be self propelled or towed bitumen pressure sprayer complete all as specified and directed by engineer in charge. 61 item no. 42 : providing and laying 30 mm thick ( consolidated thickness ) bituminous concrete ( bc ) layer conforming to clause 507 of mort&h specifications for road and bridge work ( fifth revision ) including cost of coarse aggregates, fine aggregates, filler, 5.5% binder ( paving bitumen grade vg 30 ) content by weight of total mix and crushed aggregates of grading 2, anti stripping agent, warm mix additives ( quantity, quality and grade as per the approved job mix formula ) etc, cleaning and pre heating of the mineral aggregate, filler & bitumen to the specific temperature, thoroughly mixing with binder of specified bitumen content, anti stripping agent, warm mix additives as per mix design in hot mix plant of 100 120 tph capacity, carrying the hot mixed materials by means of tipper, trucks, or any other approved and suitable arrangements, laying the hot premixed materials over the prepared surface by means of paver finisher including manual operation as and when required for proper grade, level and camber thorough rolling with power roller 8 to 12 tonnes smooth wheeled, vibratory and tandem roller with necessary hand packing and pinning to give an even surface, including running expense of all plants and machineries, inclusive of proper traffic control during laying to the satisfaction of engineer in charge, required quality control tests at required interval etc complete in all respects complete all as specified and directed by engr in charge. n n n 62 ( item no 42 contd..... ) notes : ( i ) the contractor shall quote the rate against item considering 5.5% vg 30 bitumen content. job mix formula as per clause no 505.3.3 of mort&h specifications for road and bridge work ( fifth revision ) for bituminous concrete shall be got designed from nit / ctl / govt engg college and shall be got approved from ge in writing well before commencement of work without any financial effect to the department. also the bitumen content shall not be less 5.4% by weight of total mix as per clause 507.2.5 of mort&h specifications ( fifth revision ) . n ( ii ) the cost of materials, transportation, job mix formula from lab and testing charges for various tests as required are included in the unit rate quoted by the contractor. n ( iii ) cost of filler i.e rock dust, hydrated lime or cement is deemed to be included in unit rate. n ( iv ) if qty of binder contents is less than the qty as specified in respective items of boq, it shall be adjusted at supply only rates of paving bitumen @ rs 45.00 per kg and if qty of binder contents is more than the qty as specified in respective items of boq no adjustment shall be made. n ( v ) after spreading of mix as per clause 507.4.7 of mort&h specifications entire surface during the operation shall be rolled with road roller 8 10 tonnes ( smooth wheeled ) followed with vibratory road roller of 8 10 tonnes static weight, followed by finish rolling with 6 to 8 tonnes smoooth wheeled tandem roller as per clause no 507.4.8 of mort&h specifications ( fifth revision ) and the cost of the same shall be deemed to be included in the quoted rate. n n 63 air conditioning 64 item no. 43: supply, install, testing and commissioning of install air cooled spilt type air conditioners electric driven ( 240 volts, single phase, 50 hz supply ) with energy efficient scroll compressor, working on r 134 a or superior environment friendly refrigerant, cordless remote operated, comprising of indoor unit, wall mounted, material of construction of indoor unit abs, power consumption ( max ) 4000 watts, outdoor unit, powder coated, integral refregerant piping, electric connection ( between indoor and outdoor unit located up to a maximum distance of 10 meters ) and condensate water drainage arrangement etc pressore testing, leak testing, vaccumisation, r 134a gas charging, shifting of indoor and outdoor unit, mounting arrangement of indoor unit with anchor fastner, support rod, vibration isolators complete of following capacity or nearest higher standard size complete of following capacity: 4500 k cal per hour ( 1.5 ton ) .bee 5 star rated complete all as specified & directed. 65 item no:44 : supply, install, testing and commissioning of install air cooled spilt type air conditioners electric driven ( 240 volts, single phase, 50 hz supply ) with energy efficient scroll compressor, working on r 34a or superior environment friendly refrigerant, cordless remote operated, comprising of indoor unit, wall mounted, material of construction of indoor unit abs, power consumption ( max ) 4000 watts, outdoor unit, powder coated, integral refregerant piping, electric connection ( between indoor and outdoor unit located up to a maximum distance of 10 meters ) and condensate water drainage arrangement etc pressore testing, leak testing, vaccumisation, r 134a gas charging, shifting of indoor and outdoor unit, mounting arrangement of indoor unit with anchor fastner, support rod, vibration isolators complete of following capacity or nearest higher standard size complete of following capacity 6000 k cal per hour ( 2 ton ) .bee 3 star rated all as specified and directred by eng in charge. 66 item no 45 voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 v to 250 v with output voltage stablilized at 230 v with accuracy of 2.5% and of following capacity complete all as specified & directed. 67 ( a ) 4.0 kva 68 ( a ) 5.0 kva 69 summer appliances 70 item no. 46 : supply and installation of desert cooler with outer body made of pgi ( plain galvanised iron ) sheet not less than 1.20 mm thickness for fixed part , thickness of pgi sheet for shutter not less than 0.80 mm thick, front grill made of pgi sheet with minimum weight 2.80 kgs. overall outer size not less than 66 cm x 66 cm x 99 cm ( height ) , electric driven copper wounded fan motor having nominal air flow capacity 4000 cum per hour and submersible pump for required flow of water ( sigle phase ) , complete all as specified & directed. 71 item no. 47: voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 v to 250 v with output voltage stablilized at 230 v with accuracy of 2.5% and of capacity 2 kva complete all as specified & directed. 72 item no. 48: supply and installed regrigerators, electric driven ( single phase ) , capacity 215 litres frost free complete all as specified & directed. 73 item no. 49 : supply and installed deep freezer hard top 320 ltrs capacity having double door complete all as specified and directed by eic 74 item no.50 : m&l for heavy duty pvc stands for placing / staging of water coolers and refrigirators of proper sizes complete all as specified & directed. 75 item no. 51 : supply and installed desert cooler electric driven ( single phase ) , having nominal air flow capcity of 4000 cum per hour complete all as specified & directed.. 76 external electrification 77 item no.52 : supply and laying sub class ‘b’ old size bricks laid adjacent to each other perpendicular to the direction of cable in trenches for protection of cable all as specified and directed. 78 item no. 53 : earthing complete with galvanised steel earth plate electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metre below ground level connected with earthing 32 x 6 mm strip galvanised iron of earthinglead all as shown in plate no. 02 to the earthing test point all as specified and indicted including testing on completion complete all as directed. ( cost of 7.5mm length of gi protection pipe shall be included in the rate of thid item. 79 item no. 54 : m&l for ms junction box made out of 2 mm thick sheet of size 300mm x 250mm x200 mm including aluminium busbar single phase with neutral of 63 amp capacity with , mcb sp 10 amp 01 nos for incoming and out going connections including necessary welding work, clamps and mounting on poles etc complete all as specefied and directed. 80 item no. 55 : s&f led street light ip 66 powder coated pressure die cast aluminium compact high power led street light fitting 25 watts with heat resistant toughned glass complete with all accessoreis watts. make: polycabpub05007 or equivalent or equivalent makes mentioned in tender documents complete all as specefied and directed. 81 item no. 56 : s & f brackets for street light lumanaries 40 mm light grade gi pipe with 2 nos clamps etc length of gi pipe not more than 1.5 metre length. ( for fixing on poles ) 82 item no. 57 : supply, levelling and well ramming sand cushioning in trenches for cable protection complete all as speified and as directed. note : thickness of sand cushioning after punning down shall be measured for payment purpose. 83 item no. 48 : item no.6 : cable ( with approved colour coding as per is ) with single core frls pvc insulated flexible multistranded copper conductor 1.1 kv grade for security light fitting ( main cable : number of runs indicated below ) along with one run of single core frls pvc insulated flexible multistranded copper conductor 1.1 kv grade for earthing in and including pvc conduits of suitable size, for 2 runs of 2.5 sqmm main cable + 1 run of 1.5 sqmm. 84 item no.58 : cable ( with approved colour coading as per is ) with single core frls pvc insulated flexible multistranded copper conductor 1.1 kv grade for security light fitting ( main cable : number of runs indicated below ) along with one run of single core frls pvc insulated flexible multistranded copper conductor 1.1 kv grade for earthing in and including pvc conduits of suitable size, for 2 runs of 2.5 sqmm main cable + 1 run of 1.5 sqmm. 85 item no. 59 : supply , installation, commissionning and testing of out door lt panel board made out of crca sheet 3.15 mm thick vermin proof factory made with angle and aluminium bus bar of capacity 200 amps for 3 phase and neutral with nessary angle iron 50 x 6 mm support frame including two coats powder painting over a coat of red oxide primer and grout in pcc complete all as specified and directed comprising of the following : nincoming n ( a ) aluminium bus bar of capacity 200 amps for 3 phase with neutral one job n ( b ) mccb 415 v, 100 a, 4 pole with over load , short circuit and earth fault protection with earth module breaking capacity 25 ka 01 nos. n ( c ) digital votl meter 0 500 volts square flush mounted with inbuild selector switch 01 nos. n ( d ) digital ampere meter square flush mounted with inbuild selector switch 01 nos n ( e ) indicator lamps ryb led type 01 set of three. ( e ) ct coils 100 / 5 a 03 nos. nout going n ( a ) mccb 63 a, 415v , 3 pole with over load short circuit protection, breaking capacity 16 ka 03 nos ( 2+1 ) n ( b ) mcb 20 a, 230v , 2 pole with over load short circuit protection, breaking capacity 10 ka 01 nos n nnote : ( i ) all mccbs / instruments / mcbs / bus bar shall be housed in a separate housing with on off latches in the housing. ( location sainik institute ) 86 external water supply 87 item no. 60 : m & l for cutting of exiting 150 mm dia ci / di / gi pipe line and including insert t of 50 mm dia branch pipe including complete earth work end joint as specified & directed. 88 item no. 61 : m&l for construction of brick masonry valve pit of size 900 x 900 x 900 mm ( internal dimension ) one brick thick wall in cm 1:4 on 100mm thick pcc 1:4:8 type d 2 ( 40mm graded aggregate ) as in foundation, and 15mm thick rendering in cement mortar ( 1:4 ) internally, externally up to 15cm below gl, providing valve pit cover made of 3mm thick ms sheet / plate, welded including provision of hinges, handle and locking arrangement including 40 x 40 x 6mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embedded in pcc block 1:2:4 type b 1 ( 20mm graded aggregate ) of size 230 x 200 x 100mm, including two coats of anti corrosive paint over a coat of red oxide zinc chrome primer and necessary earth work in soft / loose soil complete all as specified & directed....

Punjab State Power Corporation Limited - Punjab

28226919 laying of tower foundations, erection to towers and stringing and sagging of conductor with earth wire for the shifting of 66kv m/s kaur sain doraha line within the land of m/s havenley developers doraha , tower foundations, erection of towers and stringing and sagging of conductor with earth wier for the construction of 66kv line...

Punjab State Power Corporation Limited - Punjab

27862766 tender for laying of tower foundations, erection to towers and stringing and sagging of counductor with earth wire for the shifting of 66kv m/s kaur sain doraha line within the land of m/s havenley developers doraha , tower foundations, erection of towers and stringing and sagging of conductor with earth wier for the construction of 66kv line...

Punjab Gramin Bank - Punjab

27750775 tender for 1 light & fan point ( 6 amp.) p & l 6 amp lights, fans, plug & five pin multi socket etc point wiring 2 x 1.0 sq mm + 1x1.5 sq mm pvc insulated multi strand copper conductor cable isi mark in conduit or under false ceiling with modular switches in ms box complete in all respect with inter connection with button holder. 2 16 amp point p & l 16 amp modular switch & five pin multi socket with indicator complete with interconnections between switch & socket with wiring 2 x4 sq mm + 1x 1.5 sq mm pvc insulated multi strand copper conductor cable form panel to point in p.v.c pipe with ms box recess in wall. & 16 a, 6 pin type power socket with 16 amp. switch 2 x 4 mm + 1.5 mm earth wire. 3 25 amp wiring for ac 25 amp. wiring 2 x 4 sq mm + 1 x 2.5 sq mm from panel to point of ac, pvc insulated multi strand copper conductor cable in p.v.c pipe, in wall or above false ceiling with metal clad in ms box recessed in wall complete with interconnection. 4. panel to ups wiring 2 x 10 sq mm pvc insulated multi strand copper conductor cable & 1.75 sq mm isi mark form panel to ups including pvc conduit pipe/ false ceiling complete in all respect. 5. computer point (1 for each computer)6. main circuit wiring (panel to switch board with pvc conduit pipe.) a copper conductor wire 2 x 2.5 sq mm + 1 x 1 sq mm earth wire for lighting circuit b 4 x10 sq mm copper conductor cable for generator set. c 4 x 25 sq mm aluminum conductor cable unarmed form meter to panel. 7. telephone point with intercom one nos telephone jack, complete with interconnections modular type isi mark including wiring with 2 x 0.51 sq mm copper with silver coated one pair pvc insulated sheathed twin core telephone wire ( for telephone) from main line to telephone jack in ms box recess in wall or under computer. (1 ro, 1 dco, 1 meeting hall & 9 nos per section) 8. call bell : p & f electrical point wiring for call bell with 2 x 1.5 sq mm pvc insulated multi strand copper conductor cable of in pvc conduit pipe wiring providing bell ceiling rose or connector & 6 amp ding done bell. 9. tube light led: p & f 22 watts tube light (on the side walls not on roof). the tube lights should philips company. 10 led –bulb p & f 20 watts in the pantry, u.p.s.the led bulbs should of philips make. 11. wall fan p & f of wall fan of havell make prima model of steel jalli with necessary wiring and switches in the cashier cabin. 12. ceiling light – 2’ 0” x 2’ 0” ( 36 watt) p & f of 2 x 2 led lights 36 watt . the rate includes the fitting of chowks, rodes wire and switches i.e. complete job in all respects. 13. down light ( 22 watt) s/i/t/c of 1 x 22 watt down light with 8 led down light with complete fitting 14. earthing for the u.p.s & dp panel (with guarantee of 10 years) supply & installation of earth stations with 600 x 600 x 3 mm thick. copper plate electrode complete with 25 mm dia “b” class g.i. pipe for watering including funnel 30 cm masonry chamber with precast rcc cover complete with salt & charcoal filling ( as per is : 3034 – 1987) incl. copper strips 25 mm x 3 mm thick. with copper base plate up to earth level 4.5 mtr. deep from earth level with complete wiring including 6 sq. mm copper wire form earth to ups & panel. 15. panel : (anchor company) supply & installation testing & commissioning of cubical type control panel made out with 16 swg crca sheet duly painted with two coat of red oxide one coat of enamel paint complete with interconnections in such a way that when main supply, security and fire alarm system remain energized both supply i.e. pseb and e/a supply complete in all respects comprising with following items: i) 3 kitkat 150 amp. , 250 amp. 4 pole mccb for pseb incoming supply. ii) 250 amp. 4 pole on load change over switch for selection of supply between e/a and pseb). iii) 1 no 100 amp. bus bars before generator & 1 no 100 amp. bus bar after generator. iv) 8 nos 4 pole mccb – 63 amp. v) 4 way tpn for light, fans & power plug vi) vaf meter including 200/5 current transformer. vii) 3 no. indication lamp. 16. small panel 3 set of d.b. , 1 on each floor continuing 4 way tpn with 12 mcb and 5 dp with mcb for ac & 1 for ups . 17. ups output & input i) 4 x 25 amp. dp with mcb 2 for input supply & 2 for output supply four plug & socket for input & output ups supply. 2 no – 4 way tpn with mcb for computers ii) 1 – 6 way tpn with mcb for down lights. 18. exhaust fan p/f of 12” dia exhaust fan 1. mcb’s & db’s & elcb 2. switch, plug & socket (metal) 3. pipe (pvc) conduit 4. tube light led 5. wires & telephone cable 6. ceiling fan/wall fans 7. spot light & light fittings 8. main panel 1. providing cat 6e cable (make d link) with labour. 2. providing cat 6e information out let single with face plate ( make d link) 3. providing to module pvc box for information outlet complete with intel connection & smb. 4. providing cat 6e mounting cord 1 meter ( make d link) 5. providing cat 6e mounting cord 2 meter ( make d link) 6. 2 jack panel – 1 for 24 ports & other for 16 ports (make d link, hcl) with fitting complete in all respect with installation of hub rack . 7. installation of p & f of u rack including fan and trey including punching of lane cable with i.o. & other end in jack panel. ...

Punjab State Transmission Corporation Limited - Punjab

27623745 dismantlement and erection of earth wire dismantlement and erection of earth wire along with all fittings including suspension clamps earthing bond dead end bodies earthing clip earthing wire damper straight joint earth wire for 132 kv nawanshahr nakkian line...

Punjab State Power Corporation Limited - Punjab

27169286 tender for laying of tower foundations, erection of towers and straining and sagging of conductor with earth wire for the construction id 66 kv line from shahjahanpur to 66 kv jalaldiwal, stringing and sagging of 2nd ckt. on existing sc on dc towers of 66 kv fatehgarh churianajnala line up to dyal bharang...

Military Engineer Services - Punjab

27051942 provision of one no 1.5 ton split ac for afnet equipment room ( afnetsite ii, signal section at af stn adampur supply and install hi wall split units indoor / outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating of cap 1.5 ton 01 nos 2. s&f single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb 01 no 3. s&f voltage stablizer suitable for 1.5 ton split ac all as specified 01 no n4. m&l sub main wiring with two single core 4.0 sqmm and one single core of 4.0 sqmm as earth wire with multi standarded copper conductor cable pvc ( frls ) insulated unsheathed cable 1100 volts grade drawn through in non metallic rigid ( is ) pvc conduit of size 25mm dia and the conduits accessories as in repair complete including making good the distrubed surface to match the existing surface complete all as specified and directed 10 rm ( complete one job ) n...

Punjab State Power Corporation Limited - Punjab

26731154 tender for laying of tower foundations erection of towers and stringing and sagging of conductor with earth wire of the construction of : errection of m/ckt, towers for 66 kv lilo arrangement of one ckt. of existing focal point s/stn. ( by replacing existing dc on dc towers ) 1.847 km / 04sq....

Northern Railway - Punjab

26667035 supply of , come along clamps for earth wire (19/2.5 mm) galvanized steel as per drg no. re/33/p/550 (make im or similar)...

Punjab State Power Corporation Limited - Punjab

26061172 laying of tower foundations erection of towers and stringing and sagging of conductor with earth wire for the construction of : 1) 66 kv line from sama to 66 kv s.s dina nagar 8.794 km/0.2 sq sc on dc towers (replacement of rail pole line from str. no. 71 to 149) 2) raising of 3 nos. 66 kv rail pole lines from batala oadian railway track 0.380 km dc on dc /0.2 sq and 0.715 km sc on dm/0.2 so (deposit wodc of railway) i) 66kv wadala granthian batala radial lineat km 3/8 3/9 ii) 66kv batala radial chahal kalan line at km 3/3 3/5 iii) 66kv batala radlal batala city line at km 2/9 3/0...

Punjab State Power Corporation Limited - Punjab

25810362 tender for laying of tower foundations erection of towers and stringing and sagging of conductor with earth wire for the construction of: 1) 66kv line from sarna to 66kv s/s dina nagar 8.794 km/0.2 sq” sc on dc towers (replacement of rail pole line from str. no. 71 to 149). 2) 3 nos. 66 kv rail pole lines from batala qadian railway track 0.380 km dc on dc/0.2 sq” and 0.715 km sc on d/c/0.2 sq” (deposit work of railway). i) 66kv wadala granthian batala radial line at km 3/8 3/9. ii) 66kv batala radial chahal kalan line at km 3/3 3/5. iii) 66kv batala radial batala city line at km 2/9 3/0....

Military Engineer Services - Punjab

25753415 providing of qty 1 no , 1 . 5 ton split type air conditioner in er ii at afs pathankot , ( i ) supply and install split type air conditioner units indoor / outdoor complete with cordless remote control unit and with cooling arrangement of capacity 1 . 5 ton including mounting arrangements for indoor and outdoor unit including copper piping of suitable length duly insulated and provisioning of drainage pipe upto outside area as required at site and making good to disturbed surfaces matching with existing complete all as specified and directed by engr in charge qty 01 no ( ii ) m&l for submain wiring of pvc insulated frls copper conductor , with two single core cable 4 . 0 sqmm and one single core 4 . 0 sqmm as earth wire in and including surface / recessed in pvc conduit complete all as specified and directed by engr in charge qty 12 rm ( iii ) m&l for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb 20 amps complete all as specified and directed by engr in charge . make: legrand / anchor / schnieder / havells qty 01 no ( iv ) supply and fixing voltage stablizer for automatic operation single phase naturally air cooled indoor type and designed for input variation 140 v to 250 v with output voltage stablizer at 230 v with accuracy of plus minus 2 . 5 % and capacity of 5 kva suitable for upto 2 . 0 tr split ac complete all as specified and directed by engr in charge qty 01 no...

Military Engineer Services - Punjab

25614203 certain sanctioned work for age b / r and age e / m at nams 2 surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed. 3 m&l for rough excavation not exceeding 1.5 m deep and getting out in soft / loose soil complete all as spd and directed. 4 excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m depth for foundation, etc., and getting out in soft / loose soil complete all as specified and directed. 5 excavating post holes or similar holes, each not exceeding 0.5 cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface 6 m&l for returning, filling in, including spreading, levelling, watering and well ramming in layers under floors or trenches complete all as specified and directed.complete all as spd 7 m&l for removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. 8 m&l hardcore of gauge not exc 63mm broken stone or boulders but not exc 100mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rolled / rammed to a true surface for levelling the surfaces 9 m & l reinforced cement concrete type a1 1:1.5:3 ( using 20 mm graded stone aggregate ) in foundations including rafts, footings and mass concrete complete all as specified and directed. 10 m & l for pcc 1:2:4 type b 2 ( using 12.5 mm graded stone aggregate ) as in flooring incl finishing the cement concrete surface even and smooth with using extra cement , rubbish off the primises complete all as specified and as directed by engg in charge. 11 m&l for cement concrete , type c1 1:3:6 ( using 40 mm graded aggregate ) as in foundation filling and mass concrete complete all as specified and directed. 12 m&l for hard core of ( broken bricks ) of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and rolled / rammed to a true surface complete all as specified and directed. 13 m & l for plain cement concrete type d2 1:4:8 ( using 40 mm graded granite stone aggregate ) in foundations, filling and mass concrete complete all as specified and directed. 14 m&l pcc 1:2:4 type b1 ( using 20 mm graded stonr aggregete ) as in coping, benching etc complete all as specified and directed. 15 supply only integral water proofing compound. 16 m&l for brick work with subclass ‘b’ bricks, straight or curved on plan exc 6m mean radius, built in cm 1:6 complete all as specified and directed. 17 m&l for brick work with locally available subclass ‘b’ old size bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:6 complete all as specified and directed by engg in charge. 18 material and labour for 15mm thick cement plaster in cm 1:4 on fair faces of brick work and finishing the surface even and smooth ( without using extra cement ) etc. complete all as specified and directed. 19 m&l for newly plastered wall surfaces and applying two coats of exterior weather proof emulsion paint over one coat alkali resistant primer complete all as specified and directed. 20 m & l for 15 17mm thick kota stone slab as in treads, risers and flooring etc. laid over 15 mm thick screed bed or bedding layers in cm 1:6 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and mirror polished polishing types complete all as specified and directed. 21 s & f mild steel rag or lewis bolts of 20 mm dia, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised and exc. 30 mm long complete all as specified and directed. 22 s & f steel work in tubular trusses and tubular posts including special shaped washers, etc., complete using but welded tubes confirming to is 1161 1979 graded st 240 complete all as specified and directed. 23 s & f rolled mild steel plates ( plain or chequered ) channels, square cut or notched, forming holes, without any attachment confirming to fe 410 w ( gde e 250 ) quality a, complete all as specified and directed. 24 m&l two coats of synthetic enamel paint over a coat of red oxide primer over steel surfaces including preparation of new surface complete all as specified and directed. 25 s&f for pre painted galvaume aluminum zinc coating gi based manglore / trapezoidal / semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding, fixed with self tapping screws as specifiedcomplete all as specified and directed. nnote design / pattern / colour of roofing sheet sheet to decided and approved by eic / ge. 26 m & l for 0.63mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings ( length and girth as fixed ) with grade of zinc coating 275 complete all as specified and direcyed. 27 use and waste form work to sides of concrfete footings and similar works for fair finished surface all as specifed and directed. 28 use and waste of form work to edges of concrfete flats, slabs etc incl fair finished surface all as specifed and directed. 29 use and waste of form to staircases with sloping or stepped soffits including risers and stringers ( excluding landing ) complete as specified and directed. 30 m & l for plain cement concrete type b1 1:2:4 ( using 20 mm graded granite stone aggregate ) in foundations, filling and mass concrete. 31 m & l for formwork to sides and soffits of floor or roof beam, lintel beams flat surface etc incl supports, overhangs etc complete all as specified. 32 m&l for box type steel window 1.25 mm thick made of erw tube p section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter ( two gauged shutters and two glazed shutter ) of erw tube p section size 50 x 20 mm and 1mm thick one / two nos openable leaf consisting of two nos sash bar of t section 20x3mm welded to frame with one no vertical mullion of erw box type t section of size 60 x 25 mm and 1.25 mm thick and fi 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like handle, tower bolt, stopper, cleat, pintal hinges, hold fast etc. ( i ) hold fast, 150mm long of 120mm x 3 mm made to shape 04 nos per window. ( ii ) handle of z sec 20mm x 25mm, 100 mm long 1 no per leaf ( iii ) ms tower bolt 150mm long 2 no per leaf ( iv ) z sec 20mm x 25 mm, 100 mm long stopper 1 no per leaf ( v ) cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge 1 no per leaf. ( vi ) ms pintal hinges of size 75mm x 12mm 2 nos per leaf . ( vii ) 10 mm square guard bar, 10 cm centre to centre. ( viii ) 25x4 mm flat iron all around for joint of both frame. ( ix ) stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples. ( x ) two coat of synthetic enamel paint to ms window and guard bar complete all as specified and directed. 33 s & f mild steel box type ventilator fixed type with glazing bar with mesh & glass as per drg no. cejz / td 06 / 07 dt 07.06.07 complete all as specified. 34 s&f tmt bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips and complete all as specified. 35 all as per item 34 here in before but 6 to 8 mm dia and including in stirrups, spacers and binders and complete all as specified. 36 supply and fixing mild steel roof truss, purlins, rail and fastenings and heavy bracket framing ( beam, tee, angle, channel, flat section ) including distrance pieces, welding work, cleats, nutand bolt etc ( fe 410w ) complete all as specified and directed. 37 s&f 1.25mm thick steel rolling shutter with ball bearing and gear operated type with bevel gear box and crank handle as specified including to hood cover , an choring rod, stopper, holdfast, pulling hook, sliding lock, handle hasp and staple and one coat of primer erected in position as indicated complete all as specified and directed by engg in charge. 38 s & f safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by engg in charge. 39 s & f ball bearing for rolling shutters complete all as specified and directed. 40 supply and fixing pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, in ridges, hips, vally gutter, drip complete all as specified and directed by engineer in charge. 41 s & f mild steel plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, without ant attachment ( fe 410 w ) gde e 250 quality a complete all as specified and as directed by engg in charge. 42 m&l for providing 75 mm thick cement concrete ( 1:3:6 ) type ci using 40mm graded stone aggregate as in plinth protection / pathway surfaces even and smooth without using extra cement. 43 m&l for pre cast rcc normal mix ( 1:2:4 ) type b1 ( using 20 mm graded stone aggregate ) . as in slabs supported on walls, beams and coloums in floors and roofs, landing balconies chaza, etc all as specified and directed . 44 m&l for 15 mm thick rendering on external surface with cement mortar ( 1:4 ) on fair face of brick or concrete surface finished even and fair using wpc @3% by weight of cement complete all specified and directed ( wpc shall be mesuredand paid saparately ) . 45 m&l for 15 mm thick rendering on internal surface with cement mortar ( 1:6 ) on fair face of brick or concrete surface finished even and fair complete all specified and directed . 46 m&l preparation of newly plastered surfaces and applying two coats of cement base paint of shade as approve over a coat of cement primer on wall complete all as specified and directed. 47 m & l for preparation of new plastered surface of walls and applying three coats of white wash as directed. 48 s&f in 3mm glass thick ordinary quality and glazing with oil putty or wooden beading and securing pins n.exc 0.50 sqm each panes complete all as specified and directed. 49 m & for reinforced cement concrete type b0 1:2:4 ( using 12.5 mm graded granite stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 159, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed 50 supply, lowering, commissioning & testing of submersible pump capacity 1350 lpm at head of 80 mtr with out let size 100 mm dia bore including electric motor driven 415 v 50 hz complete all as specified and directed. 51 supply, lowering, commissioning & testing of submersible pump capacity 1650 lpm at head of 80 mtr with out let size 125 mm dia bore including electric motor driven 415 v 50 hz complete all as specified and directed. 52 supply, lowering and fixing ms heavy duty flanged pipe 5.4mm thick 100 mm bore ( length not less thatn 3 mtr each ) ms flanged not less than 15mm thick on both side, with drilled holes and welded to ms pipe, including material and labour for jointing, fixing with nuts, bolt, rubber packing complete all as specified and directed. 53 supply, lowering and fixing ms heavy duty flanged pipe 5.4mm thick 150 mm bore or nearest higher size bore ( length not less thatn 3 mtr each ) ms flanged not less than 15mm thick on both side, with drilled holes and welded to ms pipe, including material and labour for jointing, fixing with nuts, bolt, rubber packing complete all as specified and directed. 54 s&f submersible cable 25 sqmm, 3 core pvc copper cable, 1100 volts gradde conforming is 694, complete with all accessories all as specified and as directed. 55 supply, laying & fixing double wall corrugated ( dwc ) pipes for passing the cable along wall / under road, path etc made of high density polythyline ( hdpe ) with all accessories i.e. all type of joints, sockets, elbows, bends and end caps etc.. all as specified and directed by engr in charge.of size 40 mm outer dia and 38 mm inner dia of pipe 56 supply, install, testing & commissioning factory made indoor type dust and vermin proof motor starter panel cubical double door hinged type compartmentalized of suitable size fabricated of crca sheet 2.0 mm thick machine pressed and angle iron frame powder coated inside and outside, including 4 pole 415 volt, ac, 50 hz, copper busbar of capacity 300 amps mounted on porcelain insulators and enclosed in bus bar chamber and connection from incoming and outgoing electric cable with suitable size thimbs.lugs with openable shutters and fixed on angle iron frame made out from 40x40x6mm angle iron andgrounted in pcc 1:2:4, type b 1 ( using 20mm graded stone agregate ) , including accomodating & comprising of the following including taking out old unserviceable motor starter panel all as specified and directed : ( a ) mccb 250 amps capacity with adjustable thermal release 4 pole of 25 ka rupturing capacity 01 no ( incomming ) . n ( b ) mccb 160 amps 25ka , three pole 415 volt 01 no. ( outgoing ) n ( c ) mcb 32 amps 10 ka tpn 415 volt 02 no. ( out going ) ( d ) ( i ) digital volt meter showing 0 500 volts complete with duly nprewired with copper cable of suitable size 01 no. ( ii ) digital ampere meter showing 0 100 amps with 01 no. n ( iii ) indication lamp ryb led type with protection fuses 01 set ( iv ) soft starter in steel enclosure comprising of the following appliances of make l&t csxi model cat part csxi 037 41 or equivalent in siemens, havells etc: na ) in built bypass contractor nb ) soft start / start stop / adjustable current limit nc ) essential motor protection against ( i ) overload ( ii ) single phasing ( iii ) instantaneous overcurrent ( iv ) phase sequence reversal ( v ) abnormality in supply ( vi ) unbalanced current nd ) thermistor protection through ptc ne ) excess start time setting 57 m & l for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below level connected an including gi strip 32 x 6 mm as earth lead upto 7.5 mtr long by means of bolts, nuts, check nuts and washers etc with gi protection pipe of 40 mm bore medium grade and connected to earthing test point all as shawn in electrical plate no 3 of sr part i and as specified or indicated including excavation & earth work in any type of soilpcc ( 1:2:4 ) type b1 ( reinforced with welded steel wire fabric ( xpm ) of weight not less than 4 kg ( sqm ) with frame funnel with 20 mm bore gi pipe medium grade watering pipe, wire mesh and lugs test point etc and testing on completion. nnot : ( a ) the unit rates includes 32 x 6mm gi pipe strip and 40mm gi protection pipe top of earth plate upto test point ) 58 m&l for point wiring with 1.5 sqmm ( nominal area ) 1100 volt pvc insulated , frls unsheathed and multi stranded copper conductor cable in and including new pvc concealed conduit not less than 20mm dia 1.5mm thick for one light / fan point or bell point controlled by one switch ( including cutting chases and making good the disturbed surfaces ) and fixing new 3mm thick hylem sheet top cover, sheet screws and 1.6mm thick gi sunken boxes included 1.5 sqmm stranded copper conductor with green pvc insulation earth contunity conductor connected to common earth dolly etc . complete all as specified and directed. note : the cost of sunken boxes and bakellite sheet is included in the quoted rate ) 59 all as per item 58 here in before but for one three pin socket outlet 5 amps independent board complete 60 all as per item 58 here in before but for one three pin 5 amps socket outlet on the same board with other switches 61 all a per item no 58 here in above but with 2.5 sq mm size cable multi stranded frls copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continuous earth wire of pvc insulated 1.5 sq mm copper solid conductor connecting to common earth dolly complete. 62 supply and fixing switch piano type 6 amps one way 230 volts ac complete all as specified and as directed 63 supply and fixing socket outlet 5 pin, 6 amps flush type 230 volts ac complete all as specified and as directed 64 supply and fixing switch piano 16 amps type one way 230 volts ac complete all as specified and as directed 65 supply and fixing socket outlet 6 pin 6 / 16 amps multi purpose flush type 230 volts ac complete all as specified and as directed 66 supply and fixing ceiling rose 65x50 mm two to three terminals complete all as specified. 67 material and labour of lamp holder insulated body with back plate angle type for batten fitting fixed on bakelite sheet 100mmx100mm with 10 watt led bulb 230v ac cool day light 6500k having maximum height 1020mm heavy duty complete all as specified. 68 m&l for two single core sub main wiring 6 sqmm multi strand pvc insulated frls copper conductor cable including pvc insulated copper conductor cable of size 6 sqmm as cotinuous earth wire connecting to common earth including pvc conduit , connections of cable with mcbs or bus bars complete all as specified and directed 69 m & l for sheet steel enclouser distribution boards, double door factory made 3 phase 415 volts 4 way with 200 amps rating copper bus bar and pvc insulated copper jumpers of suitable size from the mccb to the out going circuits one incoming mccb and 12 outgoing mcbs circuits comprising of 3 phase 4 wire of suitable rating complete all as spcd and directed with the following accessories : ( for out going mcb measured and paid for separately ) ( a ) mccb 100 amps, 16 ka, tp, 415 volts, 50 hz = 01 no. 70 supply and fixing mcb single pole 6 to 32 amps all as specified and directed 71 supplying and fixing mcb dp 40 amps 240v, 10 ka, complete all as specified and as directed 72 m&l for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by gi pipe 15 mm bore ( light grade ) and watering pipe 20 mm bore gi pipe ( light grade ) and chamber of pcc 1:4:8 type d2 using 40 mm graded stone aggregate and coping shall be in pcc 1:3:6 type c1 using 20mm graded stone agg. 50 mm thick cover of rcc 1:2:4 type b1 using 20 mm graded stone agg. reinforced with 8 mm dia ms tor bar @ 80 mm c / c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 5 of ssr pt 1, 1991 with charcoal dust and salt complete and earth lead connected to earthing test point ( up to main switche, dbs ) complete all as specified & testing on completion. 73 supply & fix of led street light luminaire 25 watt 6000k with .high power led cool white, cri 75, + / 5% supply voltage 220 / 240 / 50 hz, light engine driver base.pole adapter, powder coated pressure die cast aluminium with heat resistant toughened glass with lens.complete all as specified and as directed. 74 supply & laying xlpe insulated armoured heavy duty electric cable with aluninium conductor 1100 volt grade cross section area 4 core 25 sqmm complete all as specified and as directed. 75 supply, laying & fixing double wall corrugated ( dwc ) pipes made of high density polythyline ( hdpe ) with all accessories i.e. all type of joints, sockets, elbows, bends and end caps etc.. all as specified and directed by engr in charge.of size50 mm outer dia and 38 mm inner dia complete all as specified and directed. 76 supply and fixing of led t 8 tube light fitting with single side connection led tube rod 18 / 20w 4 feet 1 x 18 / 20 watt ms crca box type including rotary type bipin holder and connection with pvc insulalted twin core 23 / 0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed. 77 supply and laying or fixing 1100 volts grade heavy duty cable with pvc insulated aluminium standard conductor served with an inner sheathing of pvc tape and over all pvc sheathed in service connections one twin core 6 sqmm cable standard conductor cable flat or circular all as specified and directed by engineer in charge. 78 s &f sheet metal enlosure for dbs where mcbs to be used double door factory made flush fixed complete with 100 amps rated bus bar 240 volts single phase 8 ways complete all as specified. 79 s &f led bulk head light fittings 10watt white including led strip as per ip65 in enginnering plastic housing withclear prismatic diffuser and making necessary connections complete all as specified 80 s & f bracket made out of gi pipe 40mm medium grade 1.2 mtr long made to shape with fixing clamps of ms flat 40x6mm nuts bolts etc for street light all as specified vand direceted. 81 supply & fixing flood light luminaire 120 watt with high power smd led cool white, supply voltage 220 / 240 / 50 hz, light engine driver base pole adapter, pressure die cast, polycarbonate, powdre coated in ip 66 incliding protection over temperature should be from the same manufacturer product complete all as specified and as directed, 82 supply and fixing ceiling fan 1200mm sweep copper winding with electronic regulator, low power consumption, high speed aluminium body with blade, double ball bearing of bee star rated including acessories connector, canopy, hanging rod and clamps , including electric connection with pvc flexible twin core copper wire from ceiling rose to ceiling fan complete all as specified and directed....

Punjab State Power Corporation Limited - Punjab

25280250 tender for laying of tower foundations erection and stringing and sagging of conductor with earth wire for the construction of (1) modification /raising of 66kv line from 220 kv s/s mandi gobindgarh g 2 to 66 kv grain market line crossing railway track at km 326/27 29 between khanna gobindgarh rly stns....

Punjab State Transmission Corporation Limited - Punjab

25192604 dismantlement and erection of earth wire dismantlement and erection of earth wire along with all fittings including suspension clamps earthing bond dead end bodies earthing clip earthing wire damper straight joint earth wire for 132 kv nawanshahr nakkian line...