39233817
tender for construction of swimming pool at nfl bathinda, punjab. ; 1 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 1000 m and lift upto 2.0 m, as directed by engineer in charge. 2 surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift up to 1.5 m. 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 20 mm nominal size ) . 4 extra for providing and mixing water proofing material in cement concrete per work in doses by weight of cement as per manufacturers specification 5 providing and laying in position machine batched and machine mixeddesign mix m 25 grade cement concrete for reinforced cement concretework, using cement content as per approved design mix, includingpumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including waterproofing inrecommended proportions as per is: 9103 to accelerate, retard settingof concrete, improve workability without impairing strength and durability as per direction of engineer in charge. 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural 6 centering and shuttering including strutting, propping etc. and removal of form work, all works in plinth level and in superstructure upto 10 mtr height in respective itemsfoundations, footings, bases of columns, etc. for mass concrete up to plinth level.retaing wall , coulmn , roof, balconies and access 7 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more, upto 10 mtr height complete as per drawing. 8 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer with 2 coats of chlorinated rubber paint, including welding and bolted with special shaped washers etc. complete. as per drawing and directions of engineer in charge: electric resistance or induction butt welded tubes complete as per drawing. 9 providing and fixing precoated galvanized iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( + 0.05 % ) total coated thickness with zinc coating 120 grams per sum as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineering charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 10 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) 11 half brick masonry with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 ( 1 cement :4 coarse sand ) 12 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 ( 1 cement: 6 fine sand ) for height upto 10m from ground level. 13 12 mm cement plaster of mix : internal plaster 1:6 ( 1 cement : 6 fine sand ) for height upto 10m from ground level. 14 6 mm cement plaster in ceiling of mix : 1:3 ( 1 cement : 3 fine sand ) 15 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sq. mtr. 16 wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : two or more coats on new work over and including priming coat. 17 providing and laying anti skid floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colors such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete 18 providing and fixing 1st quality swimming poolmosiac tiles ( blue colour ) / wall tiles conforming to is : 15622 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 19 providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge : flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent 20 providing and fixing alumnium work for doors, sliding windows, ventilators and partition with extruded built up standard tubular sectuions / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, botton and sides with required epdm rubber / pvc / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, cp brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing and panelling to be paid for separately, under this item the weight of only aluminium sections shall be taken for payment purpose ) . 21 for fixed portion ( powder coated aluminium minimum thickness of powder coating 50 micron ) 22 for shutters of doors, sliding windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required including tower bolts, window locking arrangement etc.. 23 providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineering charge. pre laminated particle board with decorative lamination on both sides. 24 providing and fixing aluminium sliding door bolts, isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) , transparent or dyed to required colour or shade, with nuts and screwsetc. complete :anodised aluminium sliding door bolt 300x16 mm 25 providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screwsetc. complete. 26 providing and fixing aluminium round shape handle of outer dia 100 mm with ss screws etc. complete as per direction of engineer incharge powder coated minimum thickness 50 micron aluminium 27 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below ( tolerance ±1mm ) , with wall thickness 2.0 mm ( ± 0.2 mm ) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm ( ± 0.1 mm ) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineerin charge: extruded section profile size 42x50 mm 28 24 mm thick factory made pvc door shutters made of styles and rails of a upvc hollow section of size 59x24 mm and wall thickness 2 mm ( ± 0.2 mm ) with inbuilt edging on both sides. the styles and rails mitred and joint at the corners by means of m.s. galvanised / plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. the styles of the shutter reinforced by inserting galvanised m.s. tube of size 20x20 mm and 1 mm ( ± 0.1 mm ) wall thickness. the lock rail made up of h section, a upvc hollow section of size 100x24 mm and 2 mm ( ± 0.2 mm ) wall thickness, fixed to the shutter styles by means of plastic / galvanised m.s. u cleats. the shutter frame filled with a upvc multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( ± 0.1 mm ) wall thickness. the panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised m.s. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of engineer in charge. ( for w.c. and bathroom door shutter ) . 29 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work over and including one priming coat. 30 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i / c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls etc 31 15 mm nominal outer dia pipes 32 20 mm nominal outer dia pipes 33 25 mm nominal outer dia pipes 34 construction of chamber for 100mm sluices valve 35 providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. 36 coupler 110 mm 37 110 mm shoe 38 bend 87.5° 39 single tee with door 40 providing and fixing square mouth s.w. gully trap class sp 1 complete with c.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size p type with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 41 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern with pvc connector with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in c.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required : single half stall urinal with 5 litre p.v.c. automatic flushing cistern 42 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, pvc connection pipes including painting of fittings and brackets, cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a single 15 mm c.p. brass pillar tap 43 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern with pvc connector pipe, including flush pipe, controlled device ( handle lever ) , conforming to is : 7231, with all fittings and with manually fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid 44 providing and fixing water closet squatting pan ( indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with pvc connector pipe, including flush pipe, with manually controlled device ( handle lever ) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 45 providing and fixing c.p brass bib cock of approved quality : 15 mm nominal bore 46 providing and fixing c.p. brass angle valve for basin mixer and geyserpoints of approved quality conforming to is:8931 : 15 mm nominal bore 47 providing and fixing c.p. brass stop cock ( concealed ) of standarddesign and of approved make conforming to is:8931.15 mm nominal bore 48 providing and fixing gun metal gate valve with c.i. wheel of approvedquality ( screwed end ) :25 mm nominal bore 49 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge. 50 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 51 rectangular shape 453x357 mm 52 rectangular shape 1500x450 mm 53 providing and fixing stainless steel ( grade 304 ) railing made of hollowtubes, channels, plates etc., including welding, grinding, buffing, polishingand making curvature ( wherever required ) and fitting the same withnecessary stainless steel nuts and bolts complete, i / c fixing the railingwith necessary accessories & stainless steel dash fasteners , stainlesssteel bolts etc., of required size, on the top of the floor or the side ofwaist slab with suitable arrangement as per approval of engineer incharge, ( for payment purpose only weight of stainless steel membersshall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . 54 providing and fixing c.p. brass shower rose with 15 or 20 mm inlet : 55 100 mm diameter 56 150 mm diameter 57 providing and laying factory made chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of engineer in charge. 58 60mm thick cement concrete paver block of m 35 gradewith approved colour, design & pattern 59 providing and fixing p.v.c. waste pipe for sink or wash basin includingp.v.c. waste fittings complete. 60 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. vitrified flooring size of tile 600x600 mm 61 providing and fixing chlorinated polyvinyl chloride ( cpvc ) 100 mm nominal inner dia pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & esting of joints complete as per direction of eic. 62 swimming pool over flow grating 63 providing & laying ms pipe 4 inch minimum 6kg presuure required 64 providing &fixing oftowel rail with all the necessary fitting complete in all respect. 65 providing & layingsoap dish, hindware company 66 providing & laying12 inch pvc pipe...
Due Date : September 21, 2023
Tender Value : ₹ 49.99 Lakhs
