Military Engineer Services - Punjab
41011149 tender for special repair of bldg no p 05 ( or living ) of fd regt at tibri mil stn.; 1 dismantling of roof brick tiles fixed in cement mortar in single layer. 2 demolition mud phuska in roofs any thickness including plastering and leeping complete all as specified and directed. 3 roughing the surface of old concrete on roof picking sweeping clean and washing down with water to remove dust / mud etc.and brushing neat cement slurry @ 3kg / sqm complete all as specified and directed. 4 m&l for cement concrete 1:2:4 type b 0 using 12.50mm graded stone aggregate using wpc as in roof padding finishing the surface even and smooth without using extra cement complete all as specified. note : wpc shall be measured and paid separately. 5 m&l for applying evenly a tack coat of hot industrial bitumen 85 / 25 at the rate of 1.6 kg per sq.m on roof surfaces complete all as specified and as directed. 6 m&l app based polymeric membrane minimum weighing 3 kg / sqm and minimum 3mm thick, reinforced with polyster non wove fabric ( weight not less than 150 gms / sqm ) laid on primed surface with bitumen primer @ 0.40 kg / sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides / longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturers instructions. 7 m&l for 40 mm thick brick tiles laid over and including 15 mm thick cement mortar 1:6, joints grouted and flush pointed in cement mortar ( 1: 3 ) mixed with 5 % of crude oil by weight of cement, flush pointing in cement mortar ( 1:3 ) shall be done as a separate process, complete all as specified and directed. 8 all a per srl item no 07 abovebut except tiles ( old serviceable dismantled tiles obtained from srl item no 01 shall be reused after necessary cleaning of mortar ) 9 m&l for cement cocnrete type b 1 ( 1:2:4 ) ( 20mm graded aggregate ) as in plinth protection thickiness of 50mm finishing the surface even and fair without using extra cement complete all as specified. 10 m&l for pcc 1:2:4 type b1 ( using 20mm graded stone agg ) as in roof kerbs or mud stops, coping, benching, rounded or chamfered on edges complete all as specified and directed. 11 demolition of cement concrete of any description and in any position ( above / below of ground level ) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed. 12 m&l plaster 15mm thick in cm 1:3 in sunken portion of slab with using waterproofing compoundcomplete all as specified and drected by engr in chargenote : water proofing compound shall be measured and paid separately. 13 supply only integral water proofing compound. 14 m&l for pcc 1:5:10 type e2 using 40 mm stone agg as in filling fdn and mass concrete, in sunken floor complete all as specified and directed. 15 m&l 25 mm thick cement concrete 1:2:4 type b 0 ( using 12.5mm graded stone aggregate ) as in sub base for receiving the floor finishes complete all as specified and directed. 16 taking down cement plaster of any description on brick walls on concrete surfaces etc including racking out joints hacking for key, scrubbing down with water etc from walls and ceiling surfaces of any descriptioncomplete all as specified and directed. 17 m&l for rendering 12mm thick plaster in cement mortar 1:6 on fair faces of brick or concrete surfaces of walls, finished surface even and smooth without using extra cement completeall as specified and directed. 18 m&l for rendering 15mm thick plaster in cement mortar 1:4 on other than fair faces of brick or concrete surfaces of walls, finished surface even and fair withwpc, upto height 12m complete all as specified and directed.note : wpc shall be measured and paid separately 19 m&l for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed. 20 m&l preparation of new plaster surface and applying two coats of oil bound distemperof wall over a coat of primeronwallcomplete all as specified and directed. 21 m&l preparation of new plaster surface and applying three coat of white wash on wall complete all as specified and directed. 22 m&l preparation of new plaster surface and applying two coats of cement base paintof wallcomplete all as specified and directed. 23 m&l preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed. 24 m&l for preparation of old surface includind brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing distempered surfaces and applyingtwo coats of oil bound distemperonwall complete all as specified and directed. 25 m&l for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc and applying two coat of white wash ht upto 12m all as directed by eng in charge 26 m&l for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying two coats of cement base paint onwall ht upto 12m complete all as specified and directed. 27 m & l for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks, etc and applying two coat of white wash all as directed by eng in charge 28 m&l for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paintcomplete all as specified and directed. 29 m&l for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paintht upto 12m complete all as specified and directed. 30 m&lfor repairing of rcc projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose rcc surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete ( 1: 2:4 ) using 12.5mm graded crushed stone aggregate, with or without facia and finished with cement sand mortar ( 1:3 ) using coarse sand in patches area n.exc 5 sqm each and thickness of rcc member exc 50mm including applying two coats of finishesto match with the existing surfaces in at any height complete all as specified.note: cost of formwork, at any height, shall be deemed to be included in unit rate quoted by the contractor. 31 demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc. 32 m&l for brick work with sub class b old size bricks, straight or curved on plan exc 6m mean radius built in cm 1:6 complete all as specified and directed. 33 m&lfor brickwork with sub class b bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as specified and directed. 34 demolition stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar. 35 m&l for green marble work 16 18 mm thick ( table rubbed and polished ) in steps, jambs, shelves, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. 36 m&l machine cut kota stone slab flooring 20 22mm thick over and including cement screed base 15mm thick in 1:4 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing ( with bees wax polish ) complete all as specified and directed. 37 labour only grinding of existing machine cut kota stone slab flooring including rubbing and polishing complete . 38 m& l non skidcoloured ceramic tiles 7 to 8 mm thick joint free ( square / rectangular ) area of each tile exceeding 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to matchincluding 15 mm thick screed bed in cm 1:6 and including demolition of existing complete all as spcified and directed. 39 m&lfor glazed ceramic coloured tiles in vertical surface of size 350x250x7mm / 450x350x7mmmm thick joint free on and incl 10mm thick screed bed in cm ( 1:4 ) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tilesincluding demolition of existing complete all as speciifed and directed by eic. 40 s&f steel window box type made of erw tube, hollow p section of size 60mmx25mm double rebated outer frame comprising double skeleton shutters i.e. guaged& glazed, shutter frame of erw tube p section size50mmx20mm with two openable leaf for each shutter consisting two nos sash bar of t section 20mmx3mm welded to frame with one vertical mullion of erw box type t section of size 60mmx25mm and fi 2mm thick welded / screwed to frame for fixing of wire gauge including ms guard bars, fittings and fixtures welded to frame / shutters as given below and all as shown on drg no. cejz / td 1020 / 08 sh 1 / 3 to 3 / 3 including one shop coat of red oxide primer and taking down old existing window complete: ( i ) thickness of the sheet shall be of 18 gauge ( ii ) hold fast, 150mm long of flat iron 12mmx3mm 04nos per window ( iii ) handle of z section 20mmx25mm, 100mm long 01nos per leaf ( iv ) ms tower bolt 150mm long 02 nos per leaf ( v ) z section 20mmx25mm, 100mm long stopper 01 nos per leaf ( vi ) cleat 55mm long of hollow square 15mmx12mm 01 nos per leaf ( vii ) ms pintol hinges size 75mmx12mm 2 nos. per leaf ( viii ) making good dismantled portion in pcc 1:2:4 type b 1 for hold fasts ( four nos for each window ) . note: wire cloth, glass, shall be measured and paid for separately 41 s&f steel window / ventilator box type made of erw tube hollow p section of size 60mmx25mm outer frame ( single rebated ) comprising glazed skelton shutter frame of erw tube p section including ms guard bars, fittings and fixtures welded to frame / shutters all as shown on drg no. cejz / td 1019 / 08 sh 1 / 3 to 3 / 3 including making good dismantled portion in pcc 1:2:4 type b 1 for hold fasts, including one shop coat of red oxide primer including taking down old existing window / ventilator complete all as specified and directed. notes: ( i ) thickness of the sheet shall be of 18 gauge. ( ii ) glass / wire mesh, shall be measured and paid for separately 42 s&f 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 sqm each complete all as specifiwd and directed. 43 s&f 4mm thick figured glass ordinary quality and glazing with oil putting in squares nexc 0.50 sqm each complete all as specifiwd and directed. 44 s&f 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 sqm each incl hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed. 45 taking down chowkats with shutter n.exc 1.50 sqm each ( without taking off shutter for the chowkats ) complete all as specified and directed. 46 taking down chowkats with shutter but exc 1.50 sqm but n.exc 4 sqm each ( without taking off shutter for the chowkats ) complete all as specified and directed. 47 taking down shutter of any description exc 1.00 sqm but n.exc 2.00 sqm each complete all as specified and directed. 48 taking down shutter of any description exc 2.00 sqm each complete all as specified and directed. 49 supply and fix for pressed steel framesof size 105 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, including pcc ( 1:3:6 ) , type c 0, ( using 12.5 mm graded stone aggregates ) as in filling of frames including one shop coat of red oxide primer completeall as specified and as directed. 50 s&f 30mm thick factory made solid pvc door shutter consisting of frame made out of ms tubes for top & bottom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. paneling of plain colourpvc sheet to be fitted in the ms frame welded / sealed to the stiles and rails with suitable pvc sheet beading and joined together with solvent cement, complete all as specified and directed. 51 s&f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. 52 s&f 30 mm thickfactory made flush shutters, solid core construction, with block board core and plywood face panels, commercialtype on both sides complete all as specified and directed. 53 s&f glazed and skeleton shutters 35mm thick of 2nd class hard wood open rebated andprepared to receive gauge & glass etc with edge of sash bar and number edges of framing plain chamfered beads for securing glass etc size of number of shutters as spd ssr part i & section 8 clause 8.24 & ( a ) complete all as specified and directed. 54 s&fstainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including beads all as specified and directed. 55 s&f in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including beads all as specified and directed. 56 s&f for mild steel framed work such as grills, gratings etc., with ends of bars shouldered and / or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe 290 gde e 165 57 s&f 18 mm thick plywood, exterior grade bwr, laminated on both side with decorative choice lamination, fire resistant, moisture resistant type for cupboard door etc. fixed with screws to timber / steel frame work incl 6mm thick lipping fixed with nails on all sides complete all as specified and directed. 58 s&f in repair 18 mm thick plywood , interior grade bwr, laminated on both side with decorative choice lamination, fire resistant, moisture resistant type for shelves etc.fixed with screws to timber / steel frame work incl 6mm thick lipping fixed with nails on all sides complete all as specified and directed. 59 s&f aluminiumanodized barrel tower bolt of extruded section 150mm long isi marked complete all as specified and directed. 60 s&f aluminium alloyed handle fabricated type anodized of size 150 mm long complete all as specified and directed. 61 s&f aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed. 62 s&f 75mm sizehasp and staple safety type aluminium anodised hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed. 63 s&f 75mm size medium weightmild steel butt hinge fixed with metal surface through bolt or weld or with screws complete all as specified and directed. 64 s&f aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixedcomplete all as specified and directed. 65 s&f in repair 300 mm long mild steel ordinary rat tail rod pattern spring, including roller and roller plate including fixing through welding / bolts / screws in metal / wooden frame complete all as specified and directed. 66 s&f 100mm size butt hinges, extruded aluminium alloy, type b 21 with galvanised mild steel hinge pin, anodised and fixed with screws complete all as specified and directed. 67 m&l for preparation of new painted wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 68 m&l for preparation of new paintedon steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed. 69 s&frotational moulded polytheylene white triple layered white water storage tanks of capacity 1000 litres, isi marked ( cylindrical vertical with closed top ) hoisted and fixed in position including 20mm bore ball brass valve, high pressure, with brass rod, polythene float and flynut and connected fittings, dismantling of existing water tank complete all as specified. 70 s&f in repair stop value 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. 71 s&f gi tubing 15mm bore medium grade, fixed to wall / ceiling or floor etc with all fittingsisi marked including taking up and down complete all as specified and directed. 72 fixing only old steel tubing including new fittings 15mm bore in new or old position including cleaning the same incl taking down complete all as specified and directed 73 s&f gi tubing 20mm bore medium grade, fixed to wall / ceiling or floor etc with all fittingsisi marked including taking up and down complete all as specified and directed. 74 fixing only old steel tubing including new fittings 20mm bore in new or old position including cleaning the same incl taking down complete all as specified and directed. 75 s&f gi tubing 32mm bore medium grade, fixed to wall / ceiling or floor etc with all fittings for spout complete all as specified and directed. 76 cutting existing steel tubing for alterations or additions and screwing existing steel tubing for alterations or additions ( or lengthening screw on pipe to form connector ) for 15mm bore complete all as specified and directed. 77 s&f in repair bib taps 15mm diacast copper alloy, chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. 78 s&f in repair stop valves or angel valve 15mm borecast copper alloy chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. 79 s&f in repair 15 mm stop cockcast copper alloy, screwed to iron pipe cp concealed type with long shank and capstan head for ( bath shower ) complete all as specified and directed. 80 s&f in repair pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. 81 s&f in repair brass cp shower rose 125 mm size with 225mm long arm swivel joint fancy type complete all as specified and directed. 82 s&f aluminium anodised towel rail 20mm dia., 60 cm longbetween flangesincluding brackets fixed to wall complete all as specified and directed. 83 s&f in repair vitreous china squatting pan “orrisa pattern” white of size 580x440mm with internal foot rest with pvc `p’ or `s’ trap, integral foot rest including connection to trap and flushing pipe etc complete all as specified and directed. 84 s&f in repair for vitreous china wash down water closet pan ( pedestal pattern ) white including p or s trap, plastic water closet seat white closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device with brass cp jet, complete all as specified and directed. 85 s&f in repair vitreous china table top wash basin, white rectangular bowl, size 550x400x140mm including 32mm size cast copper alloy cp waste coupling and 32mm bore pvc waste pipe complete all as specifed and directed. 86 s&f in repair vitreous china half stall type urinal , size 345x320x560mm, white, with brass cp spreader including providing and fixing plugs, bedding urinal against wall in cement mortar ( 1:2 ) , securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement paste, 32mm dia pvc flush pipe and discharge pipe, grating and union for discharge pipe, waste coupling of ptmt ( half or full threaded ) bore dia of discharge pipe 32mm ( minimum weight 45gms ) complete all as specified and as directed. 87 s&f in repairs 10 litres capacitypvc valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle, 32mm dia pvc flush pipe and connections, jointsto pipes, complete all as specified and as directed. 88 s&f in repair pvc connections 15 mm size with ptmt nuts of length 600 mmcomplete all as specified and directed. 89 s&f bevelled edge mirror of selected quality glass fancy type, size as required and fixed to wallwith chromium plated brass screws and studs and cup washers including fixing with wall complete all as specified and directed by engr in charge. 90 dismantling of cast iron , pvc or sgsw drain pipes, jointed in cement mortar and taking out of trenches , if required. 91 s&f pvc ( swr ) pipes 110mm dia in any length with rubber ring joint fixed to wall / floor upto 12m height complete all as specified and directed. 92 s&f pvc ( swr ) pipes 75mm dia in any length with rubber ring joint fixed to wall / floor upto 12m height complete all as specified and directed. 93 s&f in repair pvc ( swr ) bends 110mm dia, in any radius, complete all as specified and directed. 94 s&f in repair pvc ( swr ) bends 75mm dia, in any radius, complete all as specified and directed. 95 s & f in repair 110 bore pvc ( swr ) branch pieces ( single t ) , junction single ( equal or unequal ) , with oval access door complete all as specified and directed. 96 s&f in repair pvc vent cowl of size 110mm. 97 m&l in repair 100mm dia pvc ( swr ) floor trap with gratingincluding jointing with solvent cement complete all as specified and directed. 98 s & f stack clamps ( 110 mm pipe ) out of 20 mm by 1.5 mm galvanised mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed. 99 supply and fixing in repair cutrain rod 20mm dia of mild steel chromium platedwith fixingbrackets, stops, rollers etc fixed to wall with screws, pvc plug including taking down existing curtain rod complete all as specified and directed. 100 m&l 75mm thick cement cocnrete type d 2 , 1:4:8 ( using 40mm stone aggregate ) as in sub base for raising level complete all as specified. 101 m&l for 60 mm thick pcc ( m 35 ) factory made coloured interlocking tiles / paver block of shape / size as conforming to is 15658, with grey cement and pigment, joints will be filled with fine sand, including dismantling of existing tiles complete all as specified and as directed by engr in charge. 102 m&l for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by engineer in charge. 103 dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof / wall coverings / crumple joints complete all as specified and directed. 104 s&f in repair aluminum, 0.56 mm thick plain, sheet in wall cladding, crumple joints and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood / steel / concrete framing with plain 40 mm lap joints including bending or turning up, mitred angles, etc. as required complete all as specified and directed by eic. 105 demolition of reinforced cement concrete ( reinforcement cut as required to facilitate demolition ) of any description and in any position not otherwise specifically provided for complete all as directed.upto 12m height all as specified & directed. 106 m&l for rcc in 1:2:4 type b 0 ( using 12.5 mm graded stone aggregate ) as in chajjas facia, shelves, lintel etc and similar work all as spd. 107 m&l for form work to rough finished surface of concrete flat to soffits ofshelves, chajja, fins etc including supports over hangs upto 12m height all as specified & directed. 108 m&l tmt bars 6mm dia and over cut to length bent to shape required including crancking spirally for hooking ends and binding with and including ms wire annealed n.less than 0.9mm dia complete all as specified. 109 supply and fix for pressed steel framesof size 125 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, including pcc ( 1:3:6 ) , type c 0, ( using 12.5 mm graded stone aggregates ) as in filling of frames including one shop coat of red oxide primer completeall as specified and as directed. 110 e / m portiontaking down carefully aluminium / copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc completeat site and making goods disturbed surfaces of walls, floors etc. 111 point wiringwith pvc insulated and pvc sheathed single core multistrandedfrls copper conductor cable of size 1.5 sqmm including concealed pvc conduit with fittings andmaking good to the disturbed surfaces with continuous earth wire of pvc insulated and pvc sheathed single core multistrandedfrls copper conductor cable of size 1.5 sqmm to commonearth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to and including ci / ms boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for one light point / fan / bell point controlled by one way switch 112 all as per srl item no 111 above but one 5 pin socket outlet 6 amps on same board. 113 all as per srl item no 111 above but 6 amps socket outlet on independent board. 114 all as per srl item no 111 above but one light point controlled by two way switches. 115 all as per srl item no 111 above butwiring with 2.5 sqmm frls multistranded copper cable including earth wire 2.5 sqmm offrls multistranded coppercable for 16 amps 3 pin socket outlet. 116 m&l for sub main wiring with two single core multi stranded pvc insulated, unsheathed copper conductorof grade 1100 volt , frls cableof size 6 sqmm ( red for phase and black for neutral ) and including electrical grade pvc conduitsof desired colour not less than 1.2 mm thick and 25 mm dia. & 6 sqmm frls multistranded copper conductor cable pvc unsheathed green coloured for earthing with complete accessories duly connected with earth duly complete and taking down old unserviceable one.note : ( a ) cost of making good the disturbed surface plastering / filling putty alongwith matching with the existing colour with mes approvalmakeof distemper is deemed to be included in the quoted rate by contractor. ( b ) three run of cable alongwith pvc conduit together shall be measured as single run. 117 s&f switch piano flush typesingle pole one way6 amps. 118 s&f socket outlet 3 pin 6 amps flush type. 119 s&f switch flush type 16 amps single pole type one way 120 s&f socket outlet 3 pin 16 amps flush type 121 s&f switch piano 2 way 6a all as specified and directed. 122 s&f in replacement surface mounting universal batten husing made of powder coated crca sheet suitabe for and upto 1 x 18 / 20w led tube rodsingle sided and taking down old unserviceable fitting complete all as specified and directed. 123 s&f led tube light 20w ultra bright led polycarbonate tube light with very high efficacy suitable for fitting into tube light batten fitting completeall asas specifiedand directed. note : the contractor will submit the lm 80 and lm 79 report from manufacturer to engineer in charge before incorporating the items in work. 124 taking down carefully ceiling fan complete fittings at site, removing fans, deposting to mes store yard and taking back to site for hanging complete all as specified and as directed. 125 hanging only ceiling fanand connecting up including provision of cable from ceiling rose to connector of fan all as specified and directed. 126 s&f in replacement of fan regulator electronic type 5 step 100 watt, 240 volt and connecting complete all as specified and directed. 127 supply and fix for lamp holder angle type, pvc / polycarbonate type with back plate, suitable for lamp holder base of and including 9 watt led retrofit lamp complete all as specified and as directed. 128 m&l ceiling rose, 3 terminals / phase / pvc / polycarbonate, isolated body 129 s&f in replaceemnt gi pipe bracket made out of gi pipe light grade 32 mm bore and bent to shape 1.5m long, ms clamps made out of ms flat iron of size 40mm x 5mm thick and drilling of hole for and including nuts, bolts and washers including painting ms clamps with two coats of synthetic enemal paint over a coat of red oxide primer including taking down the existing gi pipe bracket complete all as specified and directed. 130 s&f in replaceemnt led street light fitting 35 watt 230 v ac outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact andcorrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection complete. 131 supply andfixed in repair sheet metalenclosure fordb’s when mcb’s to beused, 240 volt 8 way spn with bus barand double door complete all asspecified anddirected.note : all the connection of incoming and out going wire in mcb will be made with thimble with suitable size as directed 132 s&fin repair mcbsinglepole 6amps to 32 amps complete all asspecified anddirected. 133 s&fin repair mcb single pole and neutral 32 amps complete all as specified and directed. 134 material and labour for replacement of distribution board made out of crca sheetdb vertical type double door tpn 4 way ms sheetincluding fixing in the wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing thefolowings: ( a ) mccb 4 pole 63 amps 16 ka breaking capacity with thermal release:01 no ( in coming ) . ( b ) bus bar made out of aluminium insulated with wire adhesive tape ryb & black :4 nos. ( c ) mcb spn 40 amp: 4 nos, mcb sp 40 amp: 04 nos ( out going ) . ( d ) connection from mccb to bus bar will be made with aluminium strip of suitable capacity as directed. 135 m&l earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground ( earth pit not less than 2.25 metres deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no.3 connected to earthing test point including testing on completion including watering gi pipe 20mm bore medium grade, 15mm bore light grade gi pipe for protection of earth lead including provision ofconcrete pit in pcc ( 1:3:6 ) type c1, pre cast rcc ( 1:2:4 ) type b1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia tmt bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia ms bar, funnel & wire mesh, excavation and earth work in any type of soil complete including dismantling existing all as specified & directed by engr in charge. 136 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core. 137 excavation in trenches in soft loose soil n.exc 1.5m wide and n.exc. 1.5m in depth for poles, stay, cable, pipe etc., including taking out brick protection and getting out all as specified. 138 returning filling including spreading, levelling and well ramming in layers each n.exc 25 cm thick in soft loose soil all as specified. 139 removing excavation material, soils to a distance n. exc 50m and depositing where directed at a level n. exe 1.5m above the starting point. 140 supply and lay brick common burnt sub class b old size for protection of cable laid in trenches for under ground cable all as specified. 141 m&l sand cushioning in trenches using fine sand to under ground cable, laid in two layers15 cm before laying the cable & 8 cm after laying the cable complete all as specified. 142 supply and fix exhaust fan, steel body ac single phase 230v of size 300mm sweep with blades and frame and louvers complete all as specified and directed. 143 a schedule of credit for old / unserviceable demolished / dismantled items has been catered for in the tender.the schedule of credit is pre priced by mes.the final amount of the tender shall be arrived at after deducting the total amount of schedule of credit from the total amount of boq as per general summary sheet catered for after schedule of credit....