40850038 tender for annual maintenance water supply scheme phase 1 & 2 water works kajauli. providing and fixing of skf make ball bearing no. 6313, c 3 for 10 mgd pump set and replacing wml bush set, including the cost of labour, alignment of pump and greasing etc. complete fitting and testing in a specified time at w/w phase 1 & 2 kajauli....
40845785 tender for civil works & labour supply....
40845722 tender for supply of safai (sweeper) labour for np moonak...
40845718 supply of labour computer operator,peon np moonak...
40845556 tender for repair to veh ( tata mobile 207 ) ba no 05c 076495punder age e / m at ge abohar; 1 engine oil 2 diesel / fuel filter 3 oil filter 4 coolant 5 steering oil 6 brake oil 7 clutch oil 8 gear oil 9 labour charges for above work...
40845546 tender for repair to veh maruti suzuki dezire ( staff car ) ba no 23b 138850x under age e / m abohar.; 1 element air filter 2 filter assy, oil 3 coolant ( golden, yellow ) 4 brake fluid gc 1500aa ( 500ml pack ) 5 distilled water 6 screen wash ( 50 ml pack ) 7 interior protection cover arena 8 paper folat mat ( 20 x 15 ) 9 ecstar petrol 0w20 iocl 10 new dezire cabin air filter 11 weight, wheel balance ( 5 gram ) 12 weight, wheel balance ( 10 gram ) 13 weight, wheel balance ( 15 gram ) 14 labour for above work ( pms 1p 20k ) 15 all brake check and clean 16 wheel balancing 4 wheel 17 wheel alignment ( 4 head ) ...
40845534 supply of street light labour np moonak...
40845533 tender for supply of beldar/pump operator labour np moonak...
40845501 tender for special repair / replacement of e / m plants and machineries at af station bhisiana; 1 supply installation , comissioning and testing of ( pump set with suitable capacity 3 ph motor ) horizontal split casing type capable of delivering 125 m3 hr at60 mtr head directly coupled with suitable capacity of electric motor 3 phase 415v 1440rpm rating as per the recommendation of manufacture of pump set, suitable new foundation same size as per oem recommendation providing new rccfoundation ( minimum height of foundation from gl 01 mtr ) , base plate made from 6 mm thick ironplate / angel suitable size as per oem recommendation pump frame , iron angles frame , anti vibration pad , nut bolts washer for holding to pump with motor , with 0 vibration of pump set, including necessery electrical connection and water connectionout let / inlet water suply pipe ci / di / ms pipe testing complete, as directed by eng in charge. pcc 1:2:4 type b 1 with 20 mm grade stone aggregate foundation bolts, nuts washer etc of suitable size, complete all as specified and directed. note 1: the cost shall be included suitable arrangement of crane to installation of new pump in 09 meter depth of sewage well and lifting of old from existing location.note 2 : the cost shall be included of dismantling and reconnecting of existing all electrical and water pipe line connection with all fittings into pump and motor. 2 supply installation , comissioning and testing of ( pump set with sitable capacity 3 ph motor ) pump set horizontal split casing non clog type capable of delivering 125 m3 hr at40 mtr head directly coupled with suitable capacity of electric motor 3 phase 415v 1440rpm rating as per the recommendation of manufacture of pump set, suitable new foundation in ( 09 mtr depth of sewage well ) same size as per oem recommendation providing new rccfoundation minimum height for foundation from base 01 metre , base plate made from 6 mm thick ironplate / angel suitable size as per oem recommendation pump frame, iron angles frame, anti vibration pad , nut bolts washer for holding to pump with motor, with 0 vibration of pump set, including necessery electrical connection and water connectionout let / inlet water suply pipe ci / di / ms pipe testing complete.as existing and as directed by eng in charge. pcc 1:2:4 type b 1 with 20 mm grade stone aggregate foundation bolts, nuts washer etc of suitable sizecomplete all as specified and directed. ( 1 pump sewage no ii ) note 1: the cost shall be included suitable arrangemen of equipment or crane to installation of new pump in 09 mtr depth of sewage well and lifting of old pump from existing location.note 2: the cost shall be included of dismantling and reconnecting of existing all electrical and water pipe line connection with all fittings into pump and motor. 3 supply installation , connecting comissioning and testing of pump setcentrifugal type ( horizantal multistage type ) 70 m3 at 40 mtr head with electric motor3 phase 415 volts, 50 c / s 1440 rpm of rating as per the recommendation of manufacturer of pump set, suitable capacity new foundation same size as per oem recommendation providing new rccfoundation, base plate made from 6 mm thick ironplate / angel suitable size as per oem recommendation pump frame, iron angles frame , anti vibration pad , nut bolts washer for holding to pump with motor , with 0 vibration of pump set, including necessery electrical connection and water connection out let / inlet water suply pipe ci / di / ms pipe testing complete.as existing and as directed by eng in charge. pcc 1:2:4 type b 1 with 20 mm grade stone aggregate foundation bolts, nuts washer etc of suitable size, complete all as specified and directed. ( 02 nos level tank ) note 1: the pump and motor should be multi stage type.note 2: the cost shall be included of dismantling and reconnecting of existing all electrical and water pipe line connection with all fittings into pump and motor. 4 supply installation , connecting comissioning and testing of pump setcentrifugal type ( horizantal split case non clogtype ) 50m3 / hr at 30 mtr head with electric motor3 phase 415 volts, 50 c / s 1450 rpm of rating as per the recommendation of manufacture of pump set, suitable capacity new foundation same size as per oem recommendation providing new rccfoundation, base plate made from 6 mm thick ironplate / angel suitable size as per oem recommendation pump frame , iron angles frame , anti vibration pad , nut bolts washer for holding to pump with motor , with 0 vibration of pump set, including necessery electrical connection and water connection outlet / inlet water suply pipe ci / di / ms pipe testing complete as existing and as directed by eng in charge. pcc 1:2:4 type b 1 with 20 mm grade stone aggregate foundation bolts, nuts, washer etc of suitable sizecomplete all as specified and directed.04 nos ( sewage 03, backwash 01 ) note 1 : the pump and motor should be split case type.note 2: the cost shall be included of dismantling and reconnecting of existing all electrical and water pipe line connection with all fittings into pump and motor. 5 supply installation , connecting comissioning and testing of ( pump set with sitable capacity 3 ph motor ) pump set of monoblock pump set suitable for 415 v , 3phase system having capacity 5 hp at 30 mtrhead with electric motor3 phase 415 volts, 50 c / s , 1500 rpm of rating as per the recommendation of manufacture of pump set, suitable capacity new foundation same size as per oem recommendation providing new rccfoundation, base plate made from 6 mm thick ironplate / angel suitable size as per oemrecommendation pump frame, iron angles frame, anti vibration pad, nut, bolts, washers for holding to pump with motor, with 0 vibration of pump set, including necessery electrical connection and water connection outlet / inlet water suply pipe ci / di / ms pipe testing completeas existing and as directed by eng in charge. pcc 1:2:4 type b 1 with 20 mm grade stone aggregate foundation bolts, nuts washer etc of suitable size, complete all as specified and directed. ( lorry filling 02 trop 01 ) note : the cost shall be included of dismantling and reconnecting of existing all electrical and water pipe line connection with all fittings into pump and motor. 6 supply installation, connecting comissioning and testing of pump set with suitable capacity motor of monoblock pump set suitable for 415 v , 3phase system having capacity 525 lpm , 18 24 mtr head . with electric motor3 phase 415 volts, 50 c / s , 2830 of rating as per the recommendation of manufacture of pump set, with trolly mounted havingrubber tyre alonwith tube & steel rimmake mrf, pump will have trolly mounted having rim size 14 inch, section width 165 mm.size of tyre 40cm x 40 cm x 14cm, tread depth of tyre 8.5 mm, menimum weight 7 kg, make mrf / ceat. the wheel will have rubber tyre alonwith tube & steel rim, nut bolt, washer etc. the wheel with suitable size bearing both wheelwill be fixes in trolly with axle , the axlce made of 65 mm dia heavy grade steel pipe , minimum length of axle 1.5 mtr, support angel iron frame made of 6 mm thick iron plate, duly painted with two coat of stove enamel paint which is capable to carry the load of monoblock pump , andpulling arrangemnt, vibration pad, nut bolts washer for holding to pump with motor, with 0 vibration of pump set, including necessery water connectioninlet / out let, testing complete.as existing and as directed by eng in charge. having arrangement ofsuitable capacity dolstarter mounted on trollyand frame having plate / angeland amp meter, voltmert, single phase preventopr, dry run protection, relay, tripping on / off indicator button, iron angles frame, anti vibration pad, nut bolts washer for holding to pump with motor and water connectioninlet / outlet testing complete as existing and as directed by eng in charge. ( trolly mounted 01 ) 7 supply installation , connecting comissioning and testing of pump set with suitable capacity motorof monoblock pump set suitable for 415 v , 3phase system having capacity 405 lpm , 12 18 mtr head . with electric motor3 phase 415 volts, 50 c / s , 2830 of rating as per the recommendation of manufacture of pump set, with trolly mounted having 400 mm dia wheel withofrubber tyre alonwith tube & steel rimmake mrf , pump will have trolly mounted having rim size 14 inch , section width 165 mm.size of tyre 40cm x 40 cm x 14cm, tread depth of tyre 8.5 mm, menimum weight 7 kg , make mrf / ceat .the wheel will have rubber tyre alonwith tube & steel rim , nut bolt , washer etc, , the wheel with suitable size bearing both wheelwill be fixes in trolly with axle , the axlce made of 65 mm dia heavy grade steel pipe , minimum length of axle 1.5 mtr , support angel iron frame made of 6 mm thick iron plate, duly painted with two coat of stove enamel paint which is capable to carry the load of monoblock pump , andpulling arrangemnt , , vibration pad , nut bolts washer for holding to pump with motor , with 0 vibration of pump set, including necessery water connectioninlet / out let, testing complete.as existing and as directed by eng in charge.make kirloskar / cg / jyoti, suitable mounting arrangement on trolly fordolstarter given in schedule , nut bolts washer for holding to pump with motor water connectioninlet / out let, testing complete.as existing and as directed by eng in charge.make kirloskar / cg / grundfoss ) / jyoti. all as directed and specified by engr in charge ( trolly mounted 04 ) 8 supply installation, comissioning and testing of pump set with suitable capacity motor of monoblock pump setde watering type having sludge handling capacity 7 mm suitable for 415 v, 3 phase system having capacity 295 lpm , 11 mtr head, with electric motor 3 phase 415 volts, 50 c / s, 2830 of rating as per the recommendation of manufacturer of pump set, pump set, with trolly mounted having 400 mm dia wheel withofrubber tyre alonwith tube & steel rimmake mrf , pump will have trolly mounted having rim size 14 inch, section width 165 mm.size of tyre 40cm x 40 cm x 14cm, tread depth of tyre 8.5 mm, menimum weight 7 kgmake mrf / ceat. the wheel will have rubber tyre alonwith tube & steel rim , nut bolt , washer etc, , the wheel with suitable size bearing both wheelwill be fixes in trolly with axle , the axlce made of 65 mm dia heavy grade steel pipe , minimum length of axle 1.5 mtr , support angel iron frame made of 6 mm thick iron plate, duly painted with two coat of stove enamel paint which is capable to carry the load of monoblock pump , andpulling arrangemnt, vibration pad, nut bolts washer for holding to pump with motor , with 0 vibration of pump set, including necessery water connectioninlet / outlettesting complete as existing and as directed by eng in charge.having suitable mounting arrangement on trolly fordolstarter given in schedule, nut bolts washer for holding to pump with motor water connectioninlet / outlet testing, complete all as specified and directed. ( trolly mounted 03 ) 9 supply testing, commisioning of pumping sets centrifugal type, ic engine driven complete ( 12 bhp ) air clooled 1500 rpm, inclusive fuel tank 20 ltr capacity, maintenance free battery 12 volt 01 no, in build self starter 01, and additional of manually hand operated axial drive arrangemnt. the diesel driven pump will have trolly mounted having rim size 14 inch, section width 165 mmsize of tyre 40cm x 40 cm x 14cm, tread depth of tyre 8.5 mm, minimum weight 7 kg, make mrf / ceat. the wheel will have rubber tyre alonwith tube & steel rim, nut bolt, washer etc. the wheel with suitable size bearing both wheelwill be fixes in trolly with axle , the axlce made of 65 mm dia heavy grade steel pipe, minimum length of axle 1.5 mtr, support angel iron frame made of 6 mm thcik iron plate, duly painted with two coat of stove enamel paint which is capable to carry the load of ic engine with centrifugal pump and pulling arrangemnt, vibration pad, nut bolts, washer for holding to pump with motor, with 0 vibration of pump set including necessery water connectioninlet / outlet testing completeas existing and as directed by eng in charge. 10 supply & fixing of hose pipe63 mm dia, 36 metres long complete as per is 884 985 including pre fitted both ends flanges made of stainles steel, complete all as specified and directed. 11 supply and fix garden irrigation green hose pipe isi mark pvc material with fibre reinforce 40 mm bore including suitable metal clamps with nut and bolts. the cost shall be included fixing of clamp, nut bolt, flage, rubber gasket etc with plastic 40 mm dia foot valve for suction pipe, complete all as specified and directed. 12 supply, install, testing and commissioning of twin lobe, roots type air blowers with motor of designed capacity and head ( 1050 cum / hr. of free air at 0.65 kg / cm2, or as required ) driven through v belt or directly coupled through flexible coupling to a tefc motor of suitable hp 7.5 phase supply, 415v, 50 cycles and complete in respect along with necassary connection to air grid, air flow meters, silencers, pressure release valves, butterfly valve nrvs, etc as shown in drawing, complete all as specified and directed.air blowers :moc : cast irontype : oil free positive displacement screw typecapacity m3 / hr @ 6000 mm wc : 1050air quality : class o [ 100% oil free air ] drive : directnoise level : < 77+ / 3 db ( a ) note: cost quoted to be inclusive of foundation and fixing of equipment to the foundation by means of base plate, grouting bolt etc.foundation shall be of pcc 1:3:6 at least450 mm above floor width of foundation shall be sufficient to give 100 mm clearance on both side of equipment. 13 takng down unserviceable air grid made of gi / ci pipe and filter media from all 03 beds and deposit out side of bed and clean filter media with fresh water and again filling of same filter media after cleaningfilter bed andsupply, install, testing and commissioning ofnew air gridfrom air blower to all 03 beds of coarse bubble, lateral & header type in medium grade ( ss304pipe 65 mm bore with frp coated 3mm thick ) construction for filter bed cap 20000 gln / hr . non clog type air dispersion system capable 3 5 cfm of air or as required with oxygen transfer efficiency of 5 6% per / meter water depth, fine bubble membrane diffusers complete in all respect with fittings, valve and suitable nrv will be fixed in air line which is capable to release the blower air and stopping sand and mud to re enter into the air pipe liner, support, clamps and accessories complete all as shown in drawings. air grid when being fed by air blower of 1050 cum / hr capacity should supply minimum following qty of air, filter bed 03 nos. note : contractor shall be required to submit air grid drawings within 30 days of placement of work order. design of air grid to be approved by accepting officer before execution. air grid to be made of ss 304 frp coated.note : the cost shall be includedss 304 pipe and fitting along with prp coating 3mm thick. 14 taking out the existing pump and motor from the base plate of capacity 40 30 hp and deposit to mes storeincluding disconnecting the existingelectrical connection, suction and delivery line including earthwork and dismantling / demolition / breaking the existing rcc / pccfoundation at main main pump house / sewage pump in depth of 09 meters from ground level, complete all as specified and directed.note the cost shall be included making good disturbed surface as same as existing using pcc 1:2:4 and cement wash. the cost shall also included removing demolition materilal obtaining from old structure and deposited 500 mtr away from pump house. the contractorwill check the site and will take measurement of existing foundation i.e. length, width, height , nut , bolt size, base frame etc. before quoting of tenderand take measurement of existing pump with motor foundation. 15 taking out the existing pumpand motor from the base plate ofcapacity 10 20 hp and deposit to mes storeincluding disconnecting the existingelectrical connection, suction and delivery line including earthwork and dismantling / demolition / breaking the existing rcc / pccfoundationat main pump house / sewage pump in depth of 09 meters from ground level, complete all as specified and directed.note the cost shall be included making good disturbed surface as same as existing using pcc 1:2:4 and cement wash. the cost shall also included removing demolition material obtaining from old structure and deposited 500 mtr away from pump house . the contractorwill check the site and will take measurement of existing foundation i.e. length, width, height , nut , bolt size , base frame etc. before quoting of tenderand take measurement of existing pump with motor foundation. 16 taking out the existing pumpand motor from the base plate ofcapacity 1 5 hp and deposit to mes storeincluding disconnecting the existingelectrical connection, suction and delivery line including earthwork and dismantling / demolition / breaking the existing rcc / pccfoundationat main pump house, complete all as specified and directed.note the cost shall be included making good disturbed surface as same as existing using pcc 1:2:4 and cement wash. the cost shall also included removing demolition material obtaining from old structure and deposited 500 mtr away from pump house . the contractorwill check the site and will take measurement of existing foundation i.e. length, width, height, nut, bolt size, base frame etc. before quoting of tenderand take measurement of existing pump with motor foundation. 17 supply, installation, testing and commissioning of chloronome plant brine based suitable for hypo strength 6 8 gpl, chlorine producingto generate 500 g / hr, salt requirement 2.12 kg / hr, water consumption 70 lph, 415 volt, 3 ph 50 hz of water per day at 2 ppm dose and capable of producing actual chlorine generated 500 kg / hr of available chlorine in the form of sodium hypochloride continous strength 0.7 to 0.8 % electrolyser will be bipolar and cathode & anode intitanium coated with mixed metal oxide and cell body is pvc with dosing pump ( 01 working and 01 standby ) mechanically actuated disphragam pump and electrolyser tank of min 500 ltrs capacity made of pvc internally and frp externally of vinyl ester resin and salt dosing tank of hdpe including supporting structure , 1mx1.5x1.2 mtr height made of fly as brick with cement mortar, 15 mm thick cement base plasterpipe lines network, pvc valve etc complete and comprehensivewarranty for 01 years for the entire unit / plant. note : the cost shall be included suitable cpacity of rectifier and electric cable, starter unit for dosing pump model no pcp 500, the cost shal be included following ( i ) inlet valve*01 no, ( ii ) inlet solenoid valve 01 no, ( iii ) manual valve at brine tank inlet 01 no, ( iv ) brine tank hdpe materila 500 lt cap 01 no, ( v ) level switch on brine tank 01 no, ( vi ) agitator01 no, ( vii ) brine tank drain valve 01 no, ( viii ) brine pump inlet / out let valve 01 no, ( ix ) strainer at brine pump suction 01 no, ( x ) brine pump 02 no, ( 1w+1s ) pump typediaphragm, pressure ratin of pump 2kg / cm2, ( xi ) acid inlet / outlet valves 02 no, acid tank 500 ltr with frp coated 01no, ( xii ) acid tank valves 03 no, ( xiv ) acidrecirculating pump 01 no, ( xv ) acid pump out let valve 01 no, ( xv ) starter cum control panel 01 no, control type relay based, power control 415 v 3 ph 50 hz make pristine water, industrial devices indian pvt ltd, chloro tech equipments pvt ltd, oximax water quality solutions ( xvi ) dc rectifier 01 no type oil / aircooled variac type, power input 415 v ac , 3 ph , 50 hz, out put 25 v dc, 130 a dc, piping and fitting as reqired oem recommendation, chloine test kit 02no. 18 ( a ) supply, install, testing and commissioning of hypo solution dosing pump / injector aquafit / supreme / earth water techonology or equivalent max pressure 8kg / cm square& max flow rate 07 ltr / hr 15 mtr headincluding all accessories such aslead tubing connecting ferrules check valves all as directed. note : the cost shall be included suitable foundation / stand to installation of dosing pump on treated water sump with follwing accessories : ( b ) preparation tank model aqua1005 of net capacity 170 ltrs frp dosing tank dia 650 x net height 375 + conical 300mm, gross height with stand 1000mm consisting of water inlet line, outlet with y strainer, drain, overflow, conical bottom of sludge deposition, pot hole with cover, level gauge ( i ) water inlet line ( ii ) out let with y strainer ( iii ) drain pipe / over flow pipe ( iv ) connecting bottom for sludge deposition ( v ) pot hole coveragitator 120 watt 900 rpm single phase flange mounted motor with plastic shaft and impeller; ( vii ) water inlet line ( viii ) outer with strainer ( ix ) drain pipe / over flow pipe ( c ) service tank model no. aqua1006 of net capacity 100 ltrs of frp dosing tank top dia 540mm x bottom dia 480mm x height 575mm consisting of water inlet line. dosing pump inlet arrangement, drain overflow, level gauge, inspection port ( i ) water inlet line ( ii ) outlet with y strainer ( iii ) drain pipe / over flow pipe ( iv ) provision of mounting pump on lid / wallagitator 120 watt 900 rpm single phase flange mounted motor with plastic shaft and impeller. 19 supply and fixingnrv ( non return valve of size 150 mm boreflanged and drilled ends ) complete, isi marked, including jointing material such as rubber gasket, bolts, nuts etc suitable for size 150 mm all as specified and as directed by eng in charge. 20 supply & fixing of strainer ytype conforming to is of size 150 mm dia flanged and drilled ends complete, isi marked including jointing material such as rubber gasket, bolts, nuts etc suitable for size 150 mm all as specified and as directed by eng in charge. 21 supply and fixing sluice valve, 150 mm pn 1.6 type flanged and drilled ends complete with brassspindle including jointing material such as rubber gasket, bolts, nuts, etc suitable for size 150 mm, complete all as specified and directed. 22 supply and fixing sluice valve, 250 mm pn 1.6 type flanged and drilled ends complete with brassspindle including jointing material such as rubber gasket, bolts, nuts etc suitable for size 250 mm, complete all as specified and directed. 23 supply and fixing sluice valve, 350 mm pn 1.6 type flanged and drilled ends complete with brassspindle including jointing material such as rubber gasket, bolts, nuts, etc suitable for size 350 mm, complete all as specified and directed. 24 supply and fixing sluice valve, 450 mm pn 1.6 type flanged and reducer for fixing sluice valve in 300 mm old ci pipe line, drilled ends complete, with brass spindle including jointing material such as rubber gasket, bolts, nuts, etc suitable for size 450 mm, complete all as specified and directed.note : the cost shall be inluded reducer for fixing 450 mm sluice valve in 300 mm dia ci pipe line and 20 mtr long 25 mm dia solid iron rod handel wiht top edge t made of 450 mm wide.the valve shall be fitted in 18 mtr under ground sump .all lighting and tools and plant required to fix in sump in existing pipe wiht leak proof arrangemnt. 25 supply and fix foot valve conforming to is 4038, 150 mm dia flnged endand rubber gasket, leather jip andcomplete, with stainless steel nut bolt rust proof including jointing material such as rubber gasket etc suitable for size 150 mm, complete all as specified and directed. 26 supply and fix foot valve conforming to is 4038, 80 mm dia flnged endand rubber gasket , leather jip andcomplete, with stainless steel nut bolt rust proof, including jointing material such as rubber gasket etc suitable for size 80 mm, complete all as specified and directed. 27 supply and fixnrv pn 1.0 ( non return valve of size 250 mm boreflanged and drilled ends complete, isi marked including jointing material such as rubber gasket, bolts, nuts, etc suitable for size 250 mm, complete all as specified and directed. 28 supply and fixnrv pn 1.6 ( non return valve of size 65 mm boreflanged and drilled ends complete, isi marked including jointing material such as rubber gasket, bolts, nuts, etc suitable for size 65 mm, complete all as specified and directed. 29 supply and fixnrv pn 1.6 ( non return valve of size 80 mm boreflanged and drilled ends complete, isi marked including jointing material such as rubber gasket, bolts, nuts, etc suitable for size 80 mm all as specified and as directed by eng in charge. 30 supply and fixnrv pn 1.6 ( non return valve of size 50 mm boreflanged and drilled ends complete, isi marked including jointing material such as rubber gasket, bolts, nuts, etc suitable for size 50 mm all as specified and as directed by eng in charge. 31 supply and fixgun metal, globe or gate valves 50 mm dia with iron wheel head, screwed both ends for iron pipe and supply fixed new one, complete all as specified and directed. 32 supply and fix foot valve conforming to is 4038, 50 mm dia flnged endand rubber gasket , leather jip andcomplete, with stainless steel nut bolt rust proof, including jointing material such as rubber gasket, , etc suitable for size 50 mm, complete all as specified and directed. 33 supply and fix sluice valve, 80 mm pn 1.6 type flanged and drilled ends complete, with stainless steel spindle including jointing material such as rubber gasket, bolts, nuts etc suitable for size 80 mm, complete all as specified and directed. 34 supply and fixgun metal globe or gate valves 65 mm dia with iron wheel head, screwed both ends for iron pipe and supply fixed new one, complete all as specified and directed. 35 supply and fix pressure gauge 100 mm dia with ball valve of pressure 25 kg / sqcm ( 40 hp 09, 30 hp 01, 20 hp 02, 10 hp 04, air blower 02 ) , complete all as specified and directed. 36 supply and fixgun metal, globe or gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and supply fixed new one, complete all as specified and directed. 37 supply and fixgun metal, globe or gate valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and supply fixed new one, complete all as specified and directed. 38 supply and fix ms erw pipe nominal dia 350 mm as per is 3589 ( 1981 ) thickness 6.0 mm, including specialfittings , joints complete for deliveryandside including necessarynutsbolts and rubber etc, all as specified and directed. note :the cost shall be inclusive for making header for connection of varios sizes of ms / di / gi pipe line for delivery includingwelding, bending work. 39 supply and fix ms erw pipe nominal dia 150 mm as per is 3589 ( 1981 ) thickness 6.0 mm, including specialjoints complete for deliveryandside including necessarynutsbolts and rubber etc, all as specified and directed for, complete all as specified and directed. note :the cost shall beinclusive for making header for connection of varios sizes of ms / di / gi pipe line for delivery includingwelding, bending work . 40 supply and laying 100 mm bores of tubes medium grade galvanised with all fittings and fixed, complete laid in trenches, complete all as specified and directed. 41 supply and laying 80 mm bores of tubes medium grade galvanised with all fittings and fixed complete laid in trenches, complete all as specified and directed. 42 supply and laying 50 mm bores of tubes medium grade galvanised with all fittings and fixed complete laid in trenches, complete all as specified and directed. 43 supply and laying 20 mm bores of tubes medium grade galvanised with all fittings and fixed complete laid in trenches, complete all as specified and directed. 44 supply and laying 25 mm bores of tubes medium grade galvanised with all fittings and fixed complete laid in trenches, complete all as specified and directed. 45 supply and fix ci fittingsflanged end up to 200 mm to 300 mm dia bore such as bends ( any type radious and angle ) tapers any type , ( straight, bens increasing, decreasing or double socket etc ) tee places single branch, y junction, double branch, cross ( all sockets or socket and spigot ) collars caps and plugs, mechanicla joints suitable for 150 / 80 / 100 mm pipe, complete all as specified and directed. note :the cost shall be included for nut bolt any size and length rquire to fix , joint of ms pipe and joint, elbow, tee, bend, flanged or existing pipe suction and delivery. 46 supply and fix ci fittingsflanged end up to 150 mm dia bore such as bends ( any type radious and angle ) tapers any type , ( straight, bens increasing, decreasing or double socket etc ) tee places single branch , y junction , double branch , cross ( all sockets or socket and spigot ) collars caps and plugs, mechanicla joints suitable for 150 / 80 / 100 mm pipe, complete all as specified and directed.note :the cost shall be included for nut bolt any size and length rquire to fix, joint of ms pipe and joint , elbow , tee, bend , flanged ro existing pipe suction and delivery. 47 taking down u / s & supply and fix new electirc control panel ( cpri approved ) for pumping sets, cubical type, for in door typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.00 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangements, shutters for each mccb / starters having hinges on one side and locating knobs press type on other side and rear openable door complete with fully enclosed bus bar chamber, having insulated bus bar made out of aluminium strips of rating 800 amps for 3 phase & nutral415 volts, 50 c / s 4 wire system, with cable entry provision completeall as specified and including suitable pcc work as per recommended by manufacturer equipped with the following items: note : ( 1 ) the cost of pcc foundation shall be deemed to be included in this item rate. ( new pump house stand by ) 2. the item will be deposit in e / m store ( main pump house ) ( a ) incoming: ( i ) mccb, 4 pole, 415 volt of rating 400 amps, 36 ka 01 no. ( i / c ) ( a ) outgoing ( i ) mccb, 4 pole, 415 volt of rating 125 amps, 25 ka 09 no. in each starter, ) ( ii ) volt meter, digital type0 500 volts with selector switch 1no. ( each starter ) ( iii ) amp meter digital type 0 150 amps, ct operated with cts and selector 09 set ( iv ) indicator lamp suitable for indicationof 3 phases 01 set of three ( v ) separate enclosure for each fully automatic star delta starter heavy dutystandard model incorporating heavy duty 4 pole contactor type dc1 dx overload typelr3d / lr1d auto start switch 3 position selector switch for spp auto spp / manual / manual voltmeter with selector switch, suppressed scale, motor on & trip led indicator star delta timer forcentrifugal pumping set 09 nos relay range 48 57 note : the each starter should have separate steel body enclosure in separate compartment for each pump total starter qty 09 nos. ( vi ) single phasing, over load, phase reversal, under volatage, dry run protection unit 09 nos. 48 taking down u / s & supply and fix new electirc control panel ( cpri approved ) for pumping sets, cubical type, for in door typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.00 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangements, shutters for each mccb / starters having hinges on one side and locating knobs press type on other side and rear openable door complete with fully enclosed bus bar chamber, having insulated bus bar made out of aluminium strips of rating 250 amps for 3 phase & nutral415 volts, 50 c / s 4 wire system, with cable entry provision completeall as specified and including suitable pcc work as per recommended by manufacturer equipped with the following items: note : the cost of pcc foundation shall be deemed to be included in this item rate. the item will be deposit in e / m store ( level tank ) ( a ) incoming: ( i ) mccb, 4 pole, 415 volt of rating 160 amps, 25 ka 01 no. ( a ) outgoing ( i ) mccb, 4 pole, 415 volt of rating 40 amps, 16 ka 03 no. pump 3, ( ii ) mccb, 4 pole, 415 volt of rating 25 amps, 16 ka 01 no. ( submersible 01 ) , ( iii ) volt meter, digital type0 500 volts with selector switch 01no. ( iv ) amp meter digital type 0 150 amps, ct operated with cts and selector 01 set ( v ) indicator lamp suitable for indicationof 3 phases 01 set of three 49 ( vi ) separate enclosure for each fully automatic star delta starter heavy dutystandard model incorporating heavy duty 4 pole contactor type dc1 dx overload typelr3d / lr1d auto start switch 3 position selector switch for spp auto spp / manual / manual voltmeter with selector switch, suppressed scale, motor on & trip led indicator star delta timer forcentrifugal pumping set 03 nos relay range 38 50, starter qty 01 nos.note : the each starter should have separate steel body enclosure in separate compartment for each pump total starter qty 03 nos. ( vii ) separate enclosure for each fully automatic dol starter heavy dutystandard model incorporating heavy duty 4 pole contactor type dc1 dx overload typelr3d, auto start switch 3 position selector switch for spp auto spp / manual / manual voltmeter with selector switch, dual analog, va meter, hour meterto monitor spcu , power on hour , motor on & trip led indicator , tp c curve mcb for short circuit protection forsumersiblepumping set 01 nos. relay range 18 25.note : the each starter should have separate steel body enclosure in separate compartment for each pump. ( vii ) single phasing, over load, phase reversal, under volatage, dry run protection unit 04 nos. 50 taking down u / s & supply and fix new electirc control panel ( cpri approved ) for pumping sets, cubical type, for in door typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.00 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangements, shutters for each mccb / starters having hinges on one side and locating knobs press type on other side and rear openable door complete with fully enclosed bus bar chamber, having insulated bus bar made out of aluminium strips of rating 120 amps for 3 phase & nutral415 volts, 50 c / s 4 wire system, with cable entry provision completeall as specified and including suitable pcc work as per recommended by manufacturer equipped with the following items: note : the cost of pcc foundation shall be deemed to be included in this item rate. ( new pump house stand by ) 2. the item will be deposit in e / m store ( air blower+ back wash ) ( a ) incoming: ( i ) mccb, 4 pole, 415 volt of rating 80 amps, 25 ka 01 no. ( a ) outgoing ( i ) mcb, 4 pole, 415 volt of rating 32 amps, 25 ka 04 nobackwash 2, air blower 02 ) ( ii ) mcb, 4 pole, 415 volt of rating 5 amps, 16 ka 01 no. ( foculator 04 ) ( iii ) volt meter, digital type0 500 volts with selector switch 01no. ( iv ) amp meter digital type 0 150 amps, ct operated with cts and selector 01 set ( v ) indicator lamp suitable for indicationof 3 phases 01 set of three ( vi ) single phasing, over load, phase reversal, under volatage, dry run protection unit 04 nos. ( vi ) separate enclosure for each fully automatic star delta starter heavy dutystandard model incorporating heavy duty 4 pole contactor type dc1 dx overload typelr3d / lr1d auto start switch 3 position selector switch for spp auto spp / manual / manual voltmeter with selector switch, suppressed scale, motor on & trip led indicator star delta timer forcentrifugal pumping set 02 nos. relay range 14 22.note : the each starter should have separate steel body enclosure in separate compartment for each pump total starter qty 02 nos. ( vii ) separate enclosure for each fully automatic star delta starter heavy dutystandard model incorporating heavy duty 4 pole contactor type dc1 dx overload typelr3d / lr1d auto start switch 3 position selector switch for spp auto spp / manual / manual voltmeter with selector switch, suppressed scale, motor on & trip led indicator star delta timer forair blower pumping set 02 nos. relay range 09 14.note : the each starter should have separate steel body enclosure in separate compartment for each pump total starter qty 02 nos. 51 supply and fixthree phase motor starterwith suitable arrangement for floor mountedthree phase dol starter ubical type, for indoordoor typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith , incoporating heavy duty 4 pole contactor type tc1 dx overload relay type lr3d, auto start switch , 3 position slector switch for single phase preventer , auto / spp manual / manual ( as4 ) , on / off rocker switch, ryb led indicator, motor on&trip led indicator, dol in sheet steel enclosure suitable for capacity submersible pump with relay range 4 6 amps cat no be1spsddx204310 make c&s / mu g6 ( ss97756 ) l&t, scheinder or equivalent.note : the cost of pcc foundation shall be deemed to be included in this item rate. 52 supply and fixthree phase motor starterwith suitable arrangement for floor mountedthree phase dol starter ubical type, for indoordoor typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith, incoporating heavy duty 4 pole contactor type tc1 dx overload relay type lr3d, auto start switch, 3 position slector switch for single phase preventer , auto / spp manual / manual ( as4 ) , on / off rocker switch, ryb led indicator, motor on&trip led indicator, dol in sheet steel enclosure suitable forcapacity submersible pump with relay range 2.5 4 amps at no be1spsddx204308 make c&s / mu g6 ( ss97756 ) l&t scheinder or equivalent.note : the cost of pcc foundation shall be deemed to be included in this item rate. ( 2 1hp 7 ) 53 supply and laying, pvc insulated and fr pvc round sheathed, copper conductor conforming to is: 694 pvc nsulated 1100 volt grade heavy duty electric cables with copper conductor, cross sectional area 35 sqmm 3 core all as specified and directed makehavells / anchor / polycab ) from mpcp to pump atmain pump house ) , level tank pump, sewage pump ) , complete all as specified and directed. 54 supply and laying , pvc insulated and fr pvc round sheathed, copper conductor conforming to is: 694 pvc nsulated 1100 volt grade heavy duty electric cables with copper conductor, cross sectional area 2.5 sqmm 3 core, complete all as specified and directed. ( db to dosing pump ) 55 supply and laying , pvc insulated and fr pvc round sheathed, copper conductor conforming to is: 694 pvc nsulated 1100 volt grade heavy duty electric cables with copper conductor, cross sectional area 16 sqmm 3 core, complete all as specified and directed. ( from panel to air blower, 30 hp sewage, 20 hp, 10 hp pump ) 56 s& f triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole mcb 32 amp ( dosing msachine ) , complete all as specified and directed. 57 material and labour for pcc 1:3:6, type c 1, using 20mm graded stone aggregate for road cutting / making plith for water storage tank / chemical dosing pump where required and fair finishing to exposed surfaces without using extra cement including necessary form work, complete all as specified and directed. 58 material and labour for brickworkwith fly ash bricksstraight or curved on plan exc 6 m mean radious built in including cement mortar 1:4 using sub class b bricks as in making wall / pillarsetc for support to ms erw pipe 300 / 150 mm dia, complete all as specified and directed. 59 supply and fix cpvc pipes sdr 11 & plain cpvc sdr 11 fittings in trenches / floors / ceiling complete including jointing and fixing accessories complete fittings such as ends, elbow, unions, reducing tee, adopetrs, sockets, plugs, hose clip laid in wall / trenches size 50 mm ( chlromes plant and dosing ) 60 x 2 nos for chloromes plant, complete all as specified and directed. 60 supply and fix cpvc ball valve ( brass insert ) size 50 mm dia as per requirement at site, complete all as specified and directed. ( chlrome plant ) 61 material and labour for fixing of chlorine test point of both outgoing line in cluding making holes in new lineand fixing of 25 mm dia gi pipe .5 mt longand butter fly valve 15bore, complete all as specified and directed. 62 taking down old unserviceable pvc water tank of any capacity and supply and fix new rotational moulded polythene water storage tank of capacity 500 ltr three layer ( cylindrical vertical with closed top ) in white colour and fix in position, complete all as specified and directed. ( main pump houise 04, sewage 01, mini 01, dosing 02, chlromes 01 ) 63 material & labour for sub main wiring ( concealed ) complete with two single core 6sq mm fr pvc insulated unsheathed stranded copper conductor cable drawn through in and including 25 mm dia rigid non metallic pvc conduit and fittingsincluding 6 sq mm fr pvc insulated unsheathed stranded copper earth cable connected to common earth dolly complete and including cutting chasing using machine cutting and making good the disturbed surface, complete all as specified and directed. note: 3 run of 6 sqmm & one run of pvc conduit shall be measured as single unit. 64 material and labour sheet metal enclosures for tpn dbs with double glazed door for incorporating mcbs, ip 43, 4 way with 415 amps rated busbar, 240 volts, as per is 8623, complete all as specified and directed. 65 supply and fixing 415 v 10 ka b curve miniature circuit breaker ( mcb ) of spn and current carrying capacity 16 32 amp, in the mcb dbcomplete with connection testing and commissioning, complete all as specified and directed. 66 supply and fixing mcb sp, 10 amps to 32 amps, c series, breaking capacity 10 ka, c curve 240 volts, 50 hz including necessary incoming and out going electric connection with suitable size of copper lugs etc, complete all as specified and directed. 67 surface excavation not exceeding 30 cm deep and averaging 10 cm deep and getting out in hard / dense soil, complete all as specified and directed. 68 supply and laying, lt ug xlpe insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 240 sqmm 3.5 core, complete all as specified and directed. ( from existingpanel to proposed pnl ) for itemno 1 pump ) 69 supply and laying , lt ug xlpe insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 150 sqmm 3.5 core, complete all as specified and directed. ( from change over to pumppanel ) 70 supply and laying , lt ug xlpe insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 70 sqmm 3.5 core, complete all as specified and directed. ( from chlronoms plant ) 71 material and labour for point wiring surfaceon wallcomplete with fr pvc insulated unsheathed 1100 volts grade, conforming to is 694, 2.5 sq mm cable sizewith 2.5 sq mm earth continuity wire for one 3 pin socket outlet, 16 amps on independent board. ( nominal area ) multi stranded copper conductor cable drawn though in and including non metallic heavy grade rigid pvc conduit accessories, isi marked, 19 / 20 mm dia including all accessories, concealed in walls / floors / ceilings etc by cutting chases using machine and making good the disturbed surface, with and including suitable modular boxes, modular switch plates and 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following, complete all as specified and directed. 72 supply and fixing socket modular type 16 amps, 3 pin combine, 2 module, 240 volts, complete all as specified and directed. 73 supply and fixing switch modular type 16 amps, 1 module, 240 volts, complete all as specified and directed. 74 material and labour for earthing complete with galvanised steel steel earth plate electrode 600x600x6mm thick burried directly in ground ( earth pit not less than 2.25 mtrs deep below nominal ground level ) with top edge of the plate not less than 1.5 mtrs below nominal ground level connected to galvanised strip 25x4 mm by means of bolts, nuts, check nuts and washers of gi all as shown in electrical plate no 3 of ssr part i connected to earthing test point and testing on completion. all as specified and as directed. note: the cast of excavation and earth work pcc pit and pcc cover with handle, funnel & watering pipe, wiremesh, charcoal dust and common salt and earth strip up to 7.5 mtrs long shall be deemed included in the unit rate for earthing, complete all as specified and directed. 75 material and labour for earthing complete with galvanised steel plate electrode, 600 x 600 x 6.0 mm thick, buried directly in ground ( earth pit not less than 2.25 mtrs deep below nominal ground level ) with top edge of the plate not less than not less than 1.5 metres below nominal ground level connected to earthing lead of 4 mm dia galvanised iron or steel wire all as shown in ssr part i para no. 4 to the earthing test point all as specified and as directed.note : the cost of excavation and earth work pcc pit and ci cover funnel & watering pipe, wiremesh, charcoal dust and common salt shall be deemed included in the unit rate for earthing, complete all as specified and directed. 76 material and labour for making holes in 200 mm dia bore in rcc wall / sump using suitbale machinery or equipment and close agian using cement mortar 1:3:4 make or repair of pot holes in existing building wall / sump for passing of pipe / cables / pipe / cabletraynote: the distuebed surface of wall to passing of pipe cable / removing of existing ductshall be make good by applying cement plaster 1:4, and if required to fill with brick work 1:3:6 and applyinputty and colour wash etc matching with the existing surfaces, complete all as specified and directed. 77 material and labour for making holes in rcc partion wall intreated water tank and fixing of 450 mm dai di pipe given inschedule. thebore in rcc wall / sump using suitbale machinery or equipment and close agian using cement mortar 1:3:4 make or repair of pot holes in existing building wall / sump note: the distuebed surface of wall to passing of pipeshall be make good by applying cement plaster 1:4, and if required to fill with brick work 1:3:6 and applyingputty and colour wash etc matching with the existing surfaces, all as specified and dir by engr in charge 78 supply and laying pipe ductile iron, s / sincluding specials, class “k 9” 450 mm ( 18” ) dia . the pipe will be fixed in rcc wall fortreated water tank depth of 03 mtr alongwiht provision of 450 mm diasluice valve 450 mm will be fixed in which is given in schedule . the shall be included all fitting required to fix pipe in rcc / pcc wall, such assocket, mechnical joint, tail piece, flange, complete all as specified and directed. 79 supplying, fabricating and installing of following sizes of hot dip galvanized ladder type cable traysof size of 150 mm x 50mm x 1.6mm thick including horizontal vertical bends, reducers, tees, cross members and other accessories as required and duly installed from the ceiling / side walls with suitable sizes of channels / angles with anti corrosion painting, full threaded gl rods etc, complete all as specified and directed. 80 supply and fixfactory sealed300 mm bore flow water meter flanged end class a material brass item iso 406411 length500 mmisi markpipe with leak proof arrangementsite. the cost shall neincluded in quoted rate including all fittiings like socket, bend, elbow , rubber gasket, t taper end, flange , nut bolts , and end cap, mechanical jointe etc including all accessories required to installation of flow meterandpreventing of back flow water in existing lineetc & laying of the same under ground ior above ground as directed by engg in charge .note: the excavation and earth work also included in quoted rate . 81 taking up or down unserviceable gitubing and connection20 mm size, complete all as specified and directed. 82 taking down unserviceable di pipeof 150 mm diaincluding all fittings with spigot and socket ends and lead joints including burning out joints and recovering lead, complete all as specified and directed. 83 taling down unserviceable ci pipeof 300 mm diaincluding all fittings with spigot and socket ends and lead joints including burning out joints and recovering lead, complete all as specified and directed. 84 taking out old unserviceable ci body nrv / sluice valve / butterefly motorised valvve size 150 dia complete with nuts, bolts, rubber gaskets etc including, complete all as specified and directed. 85 taking down unserviceable air blower of existing size from foundation and deposit to mes store, complete all as specified and directed. 86 taking out old unserviceable ci body y strainerof size 150 mm, dia nuts, bolts, rubber gaskets etc, complete all as specified and directed. ( main pump house ) 87 taking out old unserviceable ci body sluice valve of size 250 / 350 mm, dianuts, bolts, rubber gaskets etc, complete all as specified and directed. ( new twt ) header by pass 2 88 taking out old unserviceable ci body sluice valve of size 450 mm, dia in depth of 18 mtr sumpnuts, bolts, rubber gaskets etc, complete all as specified and directed. ( level tbak 01 , gate 04 ) 89 taking out old unserviceable ci body foot valveof size 150 mm, dianuts, bolts, rubber gaskets etc, complete all as specified and directed. ( main pump house ) 90 taking out old unserviceable ci body or gun metalgate valve / nrvof size 65 mm, dianuts, bolts, rubber gaskets etc, complete all as specified and directed. ( grid 06 , blower 01 ) 91 taking out oldunserviceable ci body sluice valve / nrvof size 80 mm, dianuts, bolts, rubber gaskets etc, complete all as specified and directed. ( lorry filing unit ) 92 taking out unserviceable lt ug xlpe insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 240 sqmm 3.5 core, complete all as specified and directed. 93 taking out unserviceable lt ug xlpe insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 150 sqmm 3.5 core, complete all as specified and directed. 94 taking out unserviceable gitubingand connection25 mm size, complete all as specified and directed. 95 taking out unserviceable 10 sqmm coppercable, complete all as specified and directed. 96 taking out unserviceable lt ug xlpe insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 70 sqmm 3.5 core, complete all as specified and directed. 97 supply and fixthree phase motor starterwith suitable arrangement forfloor mountedthree phase star delta starter ubical type, for indoordoor typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith , incoporating heavy duty 4 pole contactor type tc1 dx overload relay type lr3d, auto start switch , 3 position slector switch for single phase preventer , auto / spp manual / manual voltmeter with selector switch , suppressedammeter , ryb led indicator, motor on&trip led indicator , tp c curve mcb for short circuit protection . sheet steel enclosure suitable forcapacity submersible pump with relay range 38 50 amps cat no be3spsddx 40357make c&s / l&t note : the cost of pcc foundation shall be deemed to be included in this item rate. ( sewae no ii ) 98 supply and fixthree phase motor starterwith suitable arrangement forfloor mountedthree phase star delta starter ubical type, for indoordoor typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith , incoporating heavy duty 4 pole contactor type tc1 dx overload relay type lr3d, auto start switch , 3 position slector switch for single phase preventer , auto / spp manual / manual voltmeter with selector switch , suppressedammeter , ryb led indicator, motor on&trip led indicator , tp c curve mcb for short circuit protection . sheet steel enclosure suitable forcapacity submersible pump with relay range 14 22 amps , complete all as specified and directed.note : the cost of pcc foundation shall be deemed to be included in this item rate. ( sludge tank 02 ) 99 supply and fixthree phase motor starterwith suitable arrangement forfloor mountedthree phase dol starter ubical type, for indoordoor typeuse, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of crca sheet of 2.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith , incoporating heavy duty 4 pole contactor type tc1 dx overload relay type lr3d, auto start switch , 3 position slector switch for single phase preventer , auto / spp manual / manual ( as4 ) , on / off rocker switch, ryb led indicator, motor on&trip led indicator , dol in sheet steel enclosure suitable forcapacity submersible pump with relay range 5.5 8 amps, complete all as specified and directed.note : the cost of pcc foundation shall be deemed to be included in this item rate. ( trop 01, lorry filling 02 ) 100 excavation in trenches soft and loose soil not exc. 1.5 m wide and notexceeding 1.5m depth for foundation of poles / laying of cables / stay / strut etc not exceeding 10 sqm on planand getting out in soft / loose soil, complete all as specified and directed. 101 returning, filling including spreading, leveling watering and well ramming in layers not exceeding 25 cm, complete all as specified and directed. 102 removing excavated material ( soil ) n.exc 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed. 103 material and labour for providingfazilka sand as in sand cushioning to under ground cable including punning down of sand in layers, complete all as specified and directed. 104 material and labour for cableprotection cover of ug lt cable by old size bricks common burnt clay building bricks sub class `b’ laid dry and flat abutting each other with width equal to length of brick and gap between adjacent brick not exceeding 10mm, complete all as specified and directed....
40845325 supply of material and skilled labour for panchayat bhawan/library at vill. jandali kalan district malerkotla (nrega convergence work)....
40845323 supply of material and skilled labour for panchayat bhawan/library at vill. rurki kalan district malerkotla (nrega convergence work)....
40845320 supply of material and skilled labour for panchayat bhawan/library at vill. kup kalan district malerkotla (nrega convergence work)....
40845317 supply of material and skilled labour for panchayat bhawan/library at vill. sandour district malerkotla (nrega convergence work)....
40844359 supply of material and skilled labour for panchayat bhawan/library at vill. kalyan district malerkotla (nrega convergence work)....
40844356 supply of material and skilled labour for panchayat bhawan/library at vill. ahmedpur district malerkotla (nrega convergence work). supply of material and skilled labour for panchayat bhawan/ library at vill. ahmedpur district malerkotla (nrega convergence work)....
40844355 supply of material and skilled labour for panchayat bhawan/library at vill. adampal district malerkotla (nrega convergence work)....
40844302 supply of material and skilled labour for panchayat bhawan/library at vill. dasaunda singh wala district malerkotla (nrega convergence work)....
40844300 supply of material and skilled labour for panchayat bhawan/library at vill. mubarkpur district malerkotla (nrega convergence work)....
40840437 hiring the outsource agency service provider for the job contract for providing highly skilled skilled semi skilled and un skilled personnal labour through outsouce...
40833753 supply of labour for lifting of solid waste in municipal council banga...
40831193 bids are invited for boqb0q mse square iron pipes , iron sheet heavy , rubberized tyre with iron hinges , welding rods , white paint , red paint , green paint , yellow paint , black paint , labour charges total quantity : 49...
40815113 tender for annual maintenance water supply scheme phase 1 to 11 and sector 70 71, mohali repair of leakage in 4* ild c.i. pipe line with lead jointing including cost of lead, spun yarn etc. & labour charges for hammering and caulking of lead in joints, excavation, dewatering, refilling after the lead jointing complete in all respects. repair of leakage in 10 i/d c.i. pipe fine with lead jointing including cost of lead, spun yarn etc. & labour charges for hammering and caulking of lead in joints, excavation, dewatering, refilling after the lead jointing complete in all respects. repair of leakage in 8 i/d c.i. pipe line with lead jointing including cost of lead, spun yarn etc. & labour charges for hammering and caulking of lead in joints, excavation, dewatering, refilling after the lead jointing complete in all respects....
40815016 tender for annual water supply maintenance scheme phase 1 to 11 and sector 70 71, sahibzada ajit singh nagar. repair of leakage in 12 i/d c.i. pipe line with lead jointing including cost of lead, spun yarn etc. & labour charges for hammering and caulking of lead in joints, excavation, dewatering, refilling after the lead jointing complete in all respects. repair of leakage in 24 i/d c.i. pipe line with lead jointing including cost of lead, spun yarn etc. & labour charges for hammering and caulking of lead in joints, excavation, dewatering, refilling after the lead jointing complete in all respects....
40814846 tender for supply of labour 1 patwari 1 pump operator 1 plumber and 1 helper for plumber for one year on dcrates through outsource at nagar panchayat narot jaimal singh...
40804940 bids are invited for upgradation of children park at jcos or accn construction of pathway 400 x 3 square feet , steel gate 6x6 square feet , earthwork including labeling of ground with tractor , arboriculture , labour work for installation of tiles steel gate and tree plantation total quantity : 5...
40801699 tender for annual maintenance water supply scheme phase 1 & 2 water works kajaull. maintenance of water supply scheme by deploying labour as pump operator (1 no.) at phase 1&2 kajaull water works on outsourced basis (through labour contractor) at minimum wages rates of state of punjab including esic, epf, lwf, bonus @8.33% & gst for the period of 01 12 2023 to 31 12 2023...
40801428 tender for works annual maintenance of sewerage drainage scheme for u/a phase 9,10, 11, sector 48c sas nagar. deployment of sewerman for the period of 01.12.2023 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by labour department punjab without any deviation like minimum wages, esi, epf,lwf, bonus, washing allowance, spl. allowances service charges 2.5%, gst. annual maintenance of sewerage drainage scheme for u/a phase 4, 5, 382, sector 57, industrial area phase 1 to 5, village shahi majra sas nagar. annual maintenance of sewerage drainage scheme for u/a phase 7, sector 70, 71,381, village matour sas nagar. deployment of sewerman for the period of 01.12.2023 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by labour department punjab without any deviation like minimum wages, esi, epf, lwf, bonus, washing allowance, spl. allowances service charges @2.5%, gst. deployment of sewerman for the period of 01.12.2023 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by labour department punjab without any deviation like minimum wages, esi, epf,lwf, bonus, washing allowance, spl. allowances annual maintenance of storm drainage scheme for u/a phase 7, sector 70,71,381, village matour sas nagar. annual maintenance of sewerage drainage scheme for u/a phase 1,2,6, 3a, village madanpur sas nagar. @2.5%, deployment of sewerman for the period of 01.12.2023 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by labour department punjab without any deviation like minimum wages, esi epf,lwf, bonus, washing allowance, spl. allowances service charges @2.5%, gst. deployment of sewerman for the period of 01.12.2023 to 31.21.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by labour department punjab without any deviation like minimum wages, esi, epf,lwf, bonus, washing allowance, spl. allowances service charges @2.5%, gst. annual maintenance of storm drainage scheme for u/a phase 4, 5, 3b2, sector 57, industrial area phase 1 to 5, village shahi majra sas nagar. annual maintenance of storm drainage scheme for u/a phase 9,10, 11, sector 48c sas nagar. annual maintenance of storm drainage scheme for u/a phase 1,2,6, 34, village madanpur sas nagar. annual maintenance of sewerage and storm drainage scheme for u/a phase 1 to 7,9 to11381,382,3a, secto70,71,48 c,57 industrial areas phase 1 5, village madanpur, matour, shahi majra sas nagar. deployment of sewerman for the period of 01.12.2023 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and llatile by labour department punjab without any deviation like minimum wages, esi, epf,lwf, bonus, washing allowance, spt. allowances service charges @2.5%, gst. deployment of sewerman for the period of 01.12.2023 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by laboum department punjab without any deviation like minimum wages, esi, epf,lwf, bonus, washing allowance, spl. allowances service charges @2.5%, gst deployment of sewerman for the period of 01.12.202 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by labour department punjab without any deviation like minimum wages, est, epf, lwf, bonus, washing allowance, spl. allowances service charges @2.5%, gst. deployment of 1 no. driver for the period of 01.12.2023 to 31.12.2023 (one month) with effect of 01.12.2023, contractor shall follow and liable by labour department punjab without any deviation like minimum wages, esi, epf,lwf, bonus, washing allowance, spl. allowances service charges 2.5%, gst...
40800699 tender for annual maintenance water supply scheme phase 1 & 2 water works kajaull. maintenance of water supply scheme by deploying labour as fitter helper (1 no.) & mcc (2 no.) at phase 1&2 kajaull water works on outsourced basis (through labour contractor) at minimum wages rates of state of punjab including esic, epf, lwf, bonus @8.33% & gst for the period of 01 12 2023 to 31 12 2023...
40800487 bids are invited for construction of basket ball court material and labour for asphalt base , synthetic all weather acrylic surface ultra cushion system 8 layer , basketball court accessories , electric score board , floodlights , other tech aspect , fabricate all around fence 8 feet in height with one opening gate on one side total quantity : 1297...
40800118 bids are invited for manpower outsourcing services minimum wage unskilled; others; mazdoor / labour...
40799311 jcb and labour for daily rent for legacy waste clear from dumpsite at np nadala...
40790991 tender for labour supply, civil work and other supply works of m.c. funds and grants...
40789580 bids are invited for ms poles made of square pipe96mmx96mm installed with base plate , ms trussess made of ms pipe of size 70mmx70mm , ms purine made of ms pipe of size 70mmx70mm , ms purline made of ms square pipe 45mmx45mm , colour coated sheets for roof and wallas , ppgi ridge cover , ppgi corner , aluminum door of size 6x3 fit , acrylic sheet for roof 6x4 fit , foundation bolt , self tapping screws , nuts and bolts , cement in bag 50 kgs , aggregate 20mm , fine sand , labour charges total quantity : 4497...
40788735 providing/laying of 6inch i/d dik 7 water supply line at labour colony near govt. school ward no. 41...
40787096 bids are invited for repair of motims project reflex shooting range simulated target without sensor for outdoor , battery charging unit , magazine for insas , co2 gas cylinder refilling reqd , hand held controller , construction of room 24x24x10 plinth base 1.20 mtr foundation base 2.00 mtrs including electricity wiring plastering roof repair and construction of door , repair of foundation base of mock of slithering platform using cement and concrete , painting of iron structure , change of rope , labour work , climbing ladder total quantity : 17...
40786992 bids are invited for tiles , wash basin , odisha toilet seat , mirror , pipe 4 inch , grout , soap dish , tube solution , cement,sand , tiles fitting and labour chrges total quantity : 29...
40785274 tender for labour outsourcing for maintenance and house keeping & sanitation works of vvip rest house badal for one year labour rates...
40783728 tender for jor mella dated 21,22,23.12.2023 shri chamkaur sahib labour for loading temporary toilet set in trucks 2) labour for loading temporary toilet set in trucks...
40772406 bids are invited for board magnetic board 8x8 , magnetic board 8x4 , white board 8x4 , accessories for installation , installation and labour charge total quantity : 9...
40770522 supply of material and skilled labour for nrega bhawan or library at village ramgarh block sehna district barnala (nrega convergence work) (retender)...
40770267 supply of material and skilled labour for nrega bhawan or library at village diwana block mehal kalan district barnala (nrega convergence work) (retender)...
40770266 supply of material and skilled labour for nrega bhawan or library at village alkra block sehna district barnala (nrega convergence work) (retender)...
40770263 supply of material and skilled labour for nrega bhawan or library at village maur nabha block sehna district barnala (nrega convergence work) (retender)...
40768808 bids are invited for chain link fence , construction material cement as per reqmt , installation tools , 5 feet lader , labour charges total quantity : 304...
40767776 bids are invited for astro turf cricket pitch and net astro turf cricket pitch , cricket practice net , pcc cement flooring , installation of net laying of turf , labour charges for cricket pitch total quantity : 10...
40765771 supply of material and skilled labour for panchayat ghar at vill. pharwahi and karmgarh block and district barnala (nrega convergence work). (retender)...
40765706 engaging labour contractor for outsourced jobs of packing filling of milk and milk products ie sfm pio wmp smp ghee white butter paneer dahi lassi kheer milk cake panjiri and shifting loading unloading of milk products packing materi...
40757469 bids are invited for cyl head and valve grinding piston ring new fitted , sliding mechanism , reverse shaft new fitted , gear box top shaft new fitted , gear box synchronizer , connecting rod new fitted , labour charges mse total quantity : 7...
40757019 bids are invited for ro servicing 50 ltr ro general servicing or maintenance including labour , 25 ltr ro general servicing or maintenance including labour , 50 ltr ro filter set of 03 nos change including labour , 25 ltr ro filter change including labour , 50 ltr ro membrane set of 03 nos change including labour , 25 ltr ro membrane change including labour , 50 ltr ro adapter change including labour , 25 ltr ro adapter change including labour , 50 ltr ro solenoid volve change including labour , 25 ltr ro solenoid volve change including labour , 25 ltr ro bio filter change including labour , 25 ltr ro sensor change including labour , 25 ltr ro motor change including labour total quantity : 74...
40756811 tender for annual water supply maintenance scheme phase 1 to 11 and sector 48/c, sahibzada ajit singh nagar. repair of leakage in 16” i/d c.i. pipe line with lead jointing including cost of lead, spun yarn etc. & labour charges for hammering and caulking of lead in joints, cost of excavation, dewatering, refilling after the lead jointing complete in all respects. 2 job rs. 35,000/ 2 repair of leakage in 4” i/d c.i. pipe line including cost of excavation, dewatering, dismantling, providing and fixing ci d joint with nut and bolts, pipe, refitting and filling the site after repair complete job in all respects. 1 job 3 repair of leakage in 4” i/d c.i. pipe line with lead jointing including cost of lead, spun yarn etc. & labour charges for hammering and caulking of lead in joints, cost of excavation, dewatering, refilling after the lead jointing complete in all respects. 2 job 4 providing and fixing 4” blank flange including nut and bolts and labour charges complete job in all respects....