Military Engineer Services - Punjab

40256556 tender for improvement to certain omqs and smqs at af station bhisiana; 2 taking down cement or cement lime plaster of any descriptionand any thickness on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 3 material and labour for rendering 15 mm thick cement plaster in cm ( 1:4 ) on fair faces of brick or concrete surfaces and finishing the surface even and fair ( without using extra cement ) etc, complete all as specified and directed. 4 material and labour for rendering 12 mm thick cement plaster in cm ( 1:6 ) on fair faces of brick or concrete surfaces and finishing the surface even and fair ( without using extra cement ) etc, complete all as specified and directed. 5 material and labour for rendering 5 mm thick cement plaster in cm ( 1:3 ) finished even and fair ( without using extra cement ) on fair faces ofconcrete surfaces in ceiling , complete all as specified and directed. 6 material and labour for rough cast plaster on brick walls consisting under coat of cement and sand mortar 1:4 not less than 10mm thick and while it is still in plastic state the rough cast mixture consisting of graded stone or fine gravel mixed with coarse sand and cement in the ratio 1:1:1 shall be applied and finish even, complete all as specified and as directed. 7 material and labour forpreparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of cement base primer on new plastered surfaces, complete all as specified anddirected by engineer in charge. 8 material and labour for preparation of new plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces, complete all as specified anddirected by engineer in charge. 9 material and labour for complete removal of existing treatmentand preparation of old plastered / unplastered surfaces of walls andapplying two coats of cement base paintover a coat of cement base primer onwall surfaces complete all as specified anddirected by engineer in charge. 10 material and labour for complete removal of existing treatment and preparation of old plastered / unplastered surfaces of walls / parapats andapplying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces, complete all as specified and as directed. 11 material and labour for prepration of new plastered surfaces of ceiling and applying three coats of white wash on ceiling , complete all as specified and directed. 12 material and labour for prepration of old plastered surfaces of ceiling and applying two coats of white wash on ceiling, complete all as specified and as directed. 13 material and labour for prepration of new plastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed. 14 material and labour for prepration of old plastered surfaces of walls and applying two coats of white wash, complete all as specified and as directed. 15 material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper acrylic / distemper oil emulsion acrylic, white or tinted over a coat ofprimer of same make, complete all as specified and as directed. 16 material and labour for complete removal of existing treatment andpreparation of old plastered surfaces of walls and applying two coats of oil bound distemper acrylic / distemper oil emulsion acrylic , white or tinted over a priming coat of same make on wall surfaces, complete all as specified and as directed. 17 material and labour applying 1 2 mm thick wall care putty ( jk / birla / berger ) on walls, including making surface even and smooth using sand paper before applying priming coat, complete all as specified and as directed. 18 demolition of reinforced cement concrete of any description and in any position, cut as required to facilitate demolition, complete all as specified and as directed. 19 demolition of reinforced cement concrete of any description and in any position ( other than ground floor ) in beams, staircases, landing chajjas and similar work, complete all as specified and as directed. 20 material and labour for reinforced cement concrete type b 1, ( 1:2:4 ) 20mm graded aggregate as in roofs, floors, kitchen platform, beams, lintels, columns, shelves, staircase, landing, parapets and railings and with similar suspanded works including necessary form work required at site and applying a coat of cement slurry over old surfaces of concrete to make perfect binding, complete all as specified and directed at site, complete all as specified and as directed. 21 all as per srl item no 20 above but as in chhajjas, complete all as specified and as directed. 22 formwork to chullah hoods, shelves, chajjas, troughs and similar items in flats including edges, complete all as specified and as directed. 23 formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 10 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide for rough finished concrete surface, complete all as specified and as directed. 24 material and labour for mild steel tmtbars 8 to 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel ( annealed ) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. 25 all as per srl iten no 23 above but 6 to 8 mm dia, complete all as specified and as directed. 26 supply and fix chicken wire mesh / hard drawn wire fabric of weight not exc 4 kg per sqm, cut to lengths, bent to shape required and tying with and including mild steel wire ( annealed ) not less than 0.9 mm dia, complete all as specified and directed. 27 demolition of cement concrete unreinforcedof any description in any position not exceeding 150 mm thick ( below or above ground level ) , complete all as specified and as directed by engineer in charge. 28 material and labour for 75 mm thick pcc ( 1:3:6 ) type c 2 using 40mm graded stone aggregate as in plinth protectionfinishing cement concrete surface even and fair without using extra cement, including making construction joint at a interval not exceeding 3.00 m and at each corner and filled with sealing compound with grade a ( normal ) in 25 / 30, complete all as specified and as directed. 29 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises, complete all as specifed and directed. 30 material and labour for 25 mm thick cement concrete type b1 ( 1:2:4 ) ( 20 mm graded stone aggregate ) , as in sub base of floor , complete all as specified and directed. 31 material and labour for non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. including 15mm thick screed bed in cm ( 1:4 ) set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed. 32 material and labour for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cm ( 1:6 ) for laying floor finishes, complete all as specified and as directed. 33 material and labour for non skid coloured ceramic tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in cm 1:4 to receive vertical tiles, complete all as specified and as directed. 34 material and labour for vetrified tiles 9 to 10 mm thick light shade ( square / rectangular ) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cm ( 1:4 ) for laying floor finishes, complete all as specified and as directed. 35 material and labour for vetrified tiles 9 to 10 mm thick light shade ( square / rectangular ) on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in cm 1:4 to receive vertical tiles, complete all as specified and as directed. 36 material and labour for glazed ceramic coloured tiles in vertical surface 350x250x7 mm / 450x350x7mm thick including 10mm thick cement plaster in cm 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and as directed. 37 demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar, complete all as specified and directed. 38 material and labour for granite ( of any type ) worktable rubbed and polished 18 20 mm thick machine cut, in steps, jams, pillars, window cills, cooking platforms and like laid and bedded over 15 mm thick cement mortar in cm ( 1:6 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to macth with shade of granite , complete all as specified and directed. 39 material and labour for 12 15mm thick green marble slab flooring including 15mm thick screed bed in cm ( 1:4 ) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab one side bullnosed etc, complete all as specified and as directed.note : cost of screed bed will deem to be included in the quoted unit rate. 40 material and labour for 12 15mm thick green marble in riser of steps , skirting, dado and pillar laid over cement screed and cement slurry including 10mm thick cement plaster 1:3 cm to receive kota stone and jointedrubbing and polishing completeall as specified and directed.note : cost of cement plaster deem to be included in the quoted unit rate. 41 rounding the edge of stone slabs one edge such as in steps, cooking platforms, and the other simmilar situation, complete all as specified and as directed. 42 material and labour for machine cut kota stone slab flooring 20 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 15mm thick screed bed of cm1:4 including rubbing and polishing, complete all as specified and as directed. 43 material and labour machine cut kota stone slab20 25mm thick in riser of steps , skirting, dado and pillar laid over cement screed and cement slurry including 10mm thick cement plaster 1:3 cm to receive kota stone and jointedrubbing and polishing, complete all as specified and as directed. 44 demolition of cement concrete ( unreinforced ) exc 15 cm thickness but above ground floor, sunkan floor, complete all as specified and as directed. 45 material and labour for 15 mm thick rendering in cement mortar ( 1:3 ) as in sunken portion walls and floor, mixed with water proofing compound 3%by weightof cement, finishing surfaces even & smooth without using extra cement complete all as specified and as directed. note : water proofing compound shall be measured and paid under appropriate item of this sch ‘a’. 46 supplying only integral water proofing compoung, mixed as per instruction given over it as per manufactures direction, complete all as specified and as directed. 47 material and labour for bitumen hot blown any grade, applied hot, intwo coats to concrete surfaces at the rate of 1.5 kg per sqm per coat, including cleaning of surfaces, complete all as specified and as directed. 48 material and labour for laying 50 micron polythelene film, black in floors of sunkan, complete all as specified and as directed. 49 material and labour for pcc ( 1:5:10 ) type e 2 using 40mm graded stone aggregate as in fillingof sunken floorand mass concrete, complete all as specified and as directed. 50 material and labour for 50 mm diagi spought pipefixed in sunken floors by means of cutting holes in wall / taaking down old u / s pipe, fixed andbeded in cement mortor / pcc ( 1:2:4 ) and making good the disturbed portion of wall, complete all as specified and as directed. 51 dismentling cast iron or reinforced concrete pipes , floor / walls up to 100 mm bore jointed in cement mortar and taking out, complete all as specified and as directed. 52 supply and fixed 100 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, laid in trenches, complete all as specified and as directed. 53 supply and fixed75 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, laid in trenches, complete all as specified and as directed. 54 supply and fixed 100 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, fixed to walls, complete all as specified and as directed. 55 supply and fixed 75mm bore cast iron soil waste and vent pipes , sand cast pipe, in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed. 56 supply and fixed in repair cast iron p or ;s; trap 100 mm bore, complete all as specified and as directed. 57 supply and fixed in repair cast iron socket ( double collar ) , 100 mm bore, complete all as specified and as directed. 58 supply and fixed in repair cast iron socket, 75 mm bore, complete all as specified and as directed. 59 s&f in repair cast iron 100 mm bore branch piece single, ( equal or unequal ) singlewith acces door, ordinary or inverted ( spigot or socket type ) or with parrallel branches, with oval access door, complete all as specified and as directed. 60 supply and fixed in repair cast iron bends, 100mm bore , ( any radius ) , disiminishing pieces or tapper ( larger bore measured ) with oval asses door, complete all as specified and as directed. 61 supply and fixed in repair cast iron bends, 75 mm bore , ( any radius ) , disiminishing pieces or tapper ( larger bore measured ) with oval asses door, complete all as specified and as directed. 62 supply and fixed in repair cast iron 75 mm bore branch piece single, ( equal or unequal ) singlewith acces door, ordinary or inverted ( spigot or socket type ) or with parrallel branches, with oval access doors, complete all as specified and as directed. 63 supply and fixed in repair for 75mm cast iron floor trapwith ss grating 100 to 125 mm dia , including jointing with solvent cement , joint to waste pipe fixed in cement concrete type b1 ( 1:2:4 ) , complete all as specified and as directed. 64 supply and fixed in repair stack clamp for 75 mm bore pipe out of 50 mm by 5 mm flat iron and 16 round round iron stay.including bolt and nuts and securing ends of stay to walls or roof, complete all as specified and as directed. 65 supply and fixed in repair stack clamp for 100 mm bore pipe out of 50 mm by 5 mm flat iron and 16 round round iron stay.including bolt and nuts and securing ends of stay to walls or roof, complete all as specified and as directed. 66 material and labour for providing precast cement concrete cover slabs using cement concrete type b1 ( 1:2:4 ) , 20 mm graded aggregate, ( for manholes etc ) and simillar works, complete all as specified and as directed. 67 taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and as directed. 68 material and labour 15 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. 69 fixing only 15 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and as directed. 70 taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and as directed. 71 material and labour 20 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. 72 fixing only 20 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and as directed. 73 taking up or down 25 mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and as directed. 74 material and labour 25 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. 75 fixing only 25 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and as directed. 76 cutting chases, pining in making good to facing where required and pointing incement mortar 1:3 for concealed water tubing , cutting not exc 10 cm girth , complete all as specified and diredcted. 77 dismantling pvcwater tanksexc 250 ltr and n exc 500 ltr and removing to store, complete all as specified and as directed. 78 material and labour, for three layered white colourrotational moulded polyethylene water storage tanks of 500 ltrcapacity ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i, complete all as specified and as directed. 79 dismantling pvcwater tanksexc 500 ltr and n exc 1000 ltr and removing to store, complete all as specified and as directed. 80 material and labour, for three layered white colourrotational moulded polyethylene water storage tanks of 1000 ltrcapacity ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i, complete all as specified and as directed. 81 material and labour, 20mm ballvalves, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed as in repairs, complete all as specified and as directed. 82 material and labour for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed screwed both ends for iron pipes or for union and fixed in repairto 20mm dia of pipe, complete all as specified and as directed. 83 material and labour gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed screwed both ends for iron pipes or for union and fixed in repair to 15 mm dia of pipe, complete all as specified and as directed. 84 material and labour vitreous china squatting pan , orissa pattern, size 580 x 440 mm white , with integral foot rests complete including provision of lime concrete bedding fixed as in repairs, complete all as specified and as directed. 85 supply and fix in repair china wash down water closet padestal pattern white excluding flush and fix to position, including seat cover and connection to drain etc, complete all as specified and as directed. 86 supply and fix health faucet fixing in pipe etc, complete all as specified and as directed. 87 supply and fix toilet paper holder of stainless steel fixed to walls, complete all as specified and as directed. 88 supply and fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass corner shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed. 89 material and labour pvc valveless , syphonic action type , flushing cistern, low level , white, with inlet, ball valve, float and handle, completewith flush pipe of polythelene of low or high density or pvc 32 mm dia , including brackets / fastening assesoriesof 10 litres capacity , fixed in repair, complete all as specified and as directed. 90 supply and fix in repair for mirror cabinet ofmin size 430x330 mm with openable door shutteras approved by ge, complete all as specified and as directed. 91 material and labour vitreous china wash basin, white , flat back, size 550x400mm fixed onbrackets or stands, including 32 mm waste coupling of ptmt ( half or full threaded ) / cp brass and corrugated waste pipe with adopter of 900 mm long, fixed in repair, complete all as specified and as directed. 92 supply and fixed in repair wash hand basinbrass cp mixture 15mm bore for mixing hot and cold water screwed down for 15 mm iron pipe and fixed, complete all as specified and as directed. 93 supply and fixed in repair 15 mm dia bore cp angular stop cock with wall flange cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union completeall as specified and as directed by engineer in charge. 94 supply and fixed in repair15 mm dia bore cp concealed stop cockcast copper alloy chromium plated with long sahnk , fancy type, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union, complete all as specified and as directed. 95 supply and fixed in repair pvc connections 15 mm size with ptmt nuts of length 450mm, complete all as specified and as directed. 96 supply and fixed in repair pvc connections 15 mm size with ptmt nuts of length 600 mm, complete all as specified and as directed. 97 supply and fixed in repair, 15 mm diabib taps , fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed. 98 supply and fixed in repair, brass cp wall mixer, 15 mm bore, for mixing hot and cold water , screwed down for iron pipe and fixed, complete all as specified and as directed. 99 supply and fixed in repair, wall mounted goose neck sink mixer ( hot and cold ) with provision of swivel arm , connecting legs and wall flanges, complete all as specified and as directed. 100 supply and fix 15mm dia pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and flu nuts screwed for iron pipe as fixed in repairs, complete all as specified and as directed. 101 supply and fixed in repair, brass chromium plated shower rose 125 mm size with or without swivel joints, including fixing to steel pipe or union, complete all as specified and as directed. 102 supply and fixed in repair, stainless steel soap dish, complete all as specified and as directed. 103 supply and fixed in repair, brass cp tubular towel rail of 20 mm dia, d type , 60 cm long between flange , fixed in repair, complete all as specified and as directed. 104 supply and fixing stainless steel towel ring round / square with cap , with fixing screws, complete all as specified and as directed. 105 supply and fixed in repair, sinks made of stainless steel 1mm thick kitchen or labo ratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm , including 40 mm bore dia cp waste coupling ( half / full threaded with 900 mm and pvc waste pipe min 900 mm long, complete all as specified and as directed. 106 supply and fixing in repair kitchen plate rack withof size 750x900 x 250mm of stainless steel, complete all as specified and as directed. 107 supply and fixing in repair kitchen plate rack withof size 750x600 x 250mm of stainless steel, complete all as specified and as directed. 108 suply and fixing coat hooks of six pegs made out of stainless steel 45 cm long ( as per sample ) , complete all as specified and as directed. 109 dismentling of boarding in any position and in any description fixed with nail, complete all as specified and as directed. 110 supply & fixing of 18 mm thick pvc ply of plain color fixed with screws, solvent cement / adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets, complete all as specified and as directed. 111 supply & fixing of 18 mm thick pvc ply of one side prelam / rigidlam and other side balancing laminate colour to make kitchen cabinet shutter / drawer front shutters, complete all as specified and as directed. 112 supply & fixing of 5 mm thick pvc ply of plain white colour fixed with screws, solvent cement / adhesive to make kitchen cabinet back covering and pull out drawer base complete as per specifications and as directed by the engineer in charge. 113 supply & fixing for 20mm wide & 1mm thick pvc edge bedding of pvc pested on edges with suitable adhesive, complete all as specified and directed 114 supply & fixing of auto closing hinges openable at 0 degree for kitchen cabinet shutters, complete all as specified and as directed. 115 supply & fixing of ball bearing runners 45 mm telescopic channel ( 20 inch ) full extension load capacity 50 kgs, complete all as specified and as directed. 116 supply & fixing of stainless steel handles 100 mm size for kitchen cabinet shutters, complete all as specified and as directed. 117 supply & fixing of chrome plated stainless steel wire basket ( storage basket ) pull out type for large utensils, size 486 x 500 mm with necessary fixing clips etc., complete all as specified and as directed. 118 supply and fixing of chrome plated stainless steel wire basket ( cup and saucer basket ) pull out type, size 530 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 119 supply and fixing of chrome plated stainless steel wire basket ( jar basket ) pull out type, size 536 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 120 supply and fixing of chrome plated stainless steel wire basket ( thali basket ) pull out type, size 380 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 121 supply and fixing of chrome plated stainless steel wire basket ( cutlery basket ) pull out type, size 380 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. . 122 supply and fixing of chrome plated stainless steel wire basket ( grain trolley ) pull out type, size 380 x 500 mm with necessary sliding frame structure, fixing clips etc, complete all as specified and as directed. 123 supply & fixing of chrome plated stainless steel wire basket ( storage / plain basket ) pull out type, size 380 x 500 mm with necessary fixing clips etc, complete all as specified and as directed. 124 supply & fixing of chrome plated stainless steel wire basket ( bottle pull out ) pull out type, size 150 to 200 mm with necessary sliding frame structure, fixing clips etc, complete all as specified and as directed. 125 material and labour continous piano hingesstainless steel , bright finish width of flaps when open 40 mm, complete all as specified and as directed. 126 supply and fixing hasp and staple safety type aluminium powder coated with mild steel pin inculding bolt to hinge plate and fix with screws 150 mm size of hasps and staples, complete all as specified and as directed. 127 supply and fixing magnetic catcherfor cupboards complete as all specified and directed by engineer in charge, complete all as specified and as directed. 128 s&f in repair 20 mm dia stainless steel polished 204 grade drapery rod / curtain rod 1 to 2mm thick with finals decorative, including fixing of brackets and both ends decorative nobs, completeall as speccified and directed as per approved sample by engr in charge. 129 supply and fixed in repairms powder coated curtain rods 18 to20 mm boreover doors and windows , with fixing ms powder coated brackets, including screws, rawal plug , and pvc powder coated fineals / fency type end bulbs at each end of curtains rod, any colour etc, complete all as specified and as directed. 130 taking down chowkhats or frames / steel windows / ventilators, not exc 1.5 sqm each ( without taking off shutters from the frames ) , complete all as specified and as directed. 131 taking down shutter of area exc 1 sqm but n exc 2 sqm each, complete all as specified and as directed. 132 solid pvc door frame of size 50mm x 47mm made out of 5mm plain coloured pvc sheet reinforced with ms square tube, supplying & fixing in opening as per specification and drawing, complete all as specified and as directed. 133 factory made solid panel pvc door shutter 30mm thick ( stile ) , consisting of frame made out of ms tubes for top & bottom rails. ms frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drg. 134 supply and fix for 100 mm sizebutt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type b 21, complete all as specified and as directed. 135 supply and fix for 125 mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed. 136 supply and fix 100 mm aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and as directed. 137 supply and fix for anodised aluminium frame for doors, windows ventilators ( powder coated ) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by engineer in charge. 138 s&f powder coated anodised aluminium side hung / sliding type window and ventilator shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, locks, glazing clips, rubber packing, anodised aluminium snap beading, screws etc, complete all as specified and as directed. 139 material and labour for sheet glass ordinary quality 5.5mm thick and glazing with oil putty or fixed with bead / glazing pins in squares n.exc 0.5 sqm each pane all corner of glass to be fixed with silicon, complete all as specified and as directed. 140 supply and fixingstainless steelwire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tack or galvanised wire staple, complete all as specified and as directed. 141 supply and fix powder coated aluminium decorative grill of size of mesh 75mm fixed with doors, window for safety of glass etc. complete all as specified and as directed. 142 supply and fix steel window / ventilator of box section having 1.25 mm thick crc sheetframe with double shutterinside gauged shutter and outsideglazed shutterwith one nos steel handle in each shutter, one nospeg stay in each shutter , complete with glazing bars and 08 nos of 10 x 10 mm square guard bars in equal spacing, devoited or welded as per sample incl one coat of red oxide primer all as specified and directed. ( the rates includes 4 mm thick plain sheet glass and galvanized mild steelwire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and 2 coat of synthetic enamel paint over a coat of zinc chrome primer ) note : the design of window to be facilitated by cooler fixing provision where ever reqd ) , complete all as specified and as directed. 143 taking down chowkats & shutters without taking offshutters from the frame, size of openingexc. 1.50 sqm but not exc 4 sqmeach. complete all as specified and as directed. 144 supply and fix pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directedof size 125 x 60mm, complete all as specified and as directed. 145 supply and fix pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directedof size 105 x 60mm, complete all as specified and as directed. 146 material and labour for pcc ( 1:3:6 ) type c 1 using 20 mm graded agg as in back of pressed steel chowkhats etc, complete all as specified and as directed. 147 material and labour for pcc ( 1:2:4 ) type b2 using 20 mm graded agg as in hold fast of steel chowkhat / frames etc, complete all as specified and as directed. 148 supply and fix framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165, complete all as specified and as directed. 149 supply and fixing, factory made, 35mm thick plain framed panelled shutters ( two panel ) with lock rail and panelof 9mm bwp commercial ply or 12mm veneered particle board with commercial veneering on both faces using 2nd class hw as in rail and style. the size of rail and style as per is 1003 ( part – i ) , kiln seasoned and chemically pressure treated, complete all as specified and as directed. 150 supply and fixed 35mm thick glazed and skelton shutter iind class hard wood , open rebated and prepare to receive glass, gauge etc. ( without sash bars ) edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of member of shutters as specified in ssr part 1 , section 8 , clause 8.24 ( a ) , complete all as specified and as directed. 151 taking down shutter of any description exc 1.00 sqm but not exc 2.0 sqm each and refixing in same opening after easing and adjusting ( chowkat / frame changed ) etc, complete all as specified and as directed. 152 supply and fixed in repair 100 mm butt hinges medium weight, cold rolled mild steel, fixed in repair, complete all as specified and as directed. 153 supply and fixed 150 aluminium anodised barrel tower bolts of extruded section and fixed, complete all as specified and as directed. 154 supply and fixed 150 aluminium anodised barrel tower bolts of extruded section and fixed in repair tower bolt, complete all as specified and as directed. 155 supply and fixed 300 mm aluminium ally, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed , complete all as specified and as directed. 156 supply and fixed 300 mm aluminium ally, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed in repair, complete all as specified and as directed. 157 supply and fixed 150 mm extruded aluminium alloy handles, fabricated typeanodised, complete all as specified and as directed. 158 supply and fixed 150 mm extruded aluminium alloy handles, fabricated typeanodised, fixed in repair handles, complete all as specified and as directed. 159 supply and fixed floor door stopper of size 140 mmof aluminium ally body and tongue, anodised, with hard drawn steel spring ficed in floors, complete all as specified and directed. 160 supply and fixed mild steel300mm ordinary rat tail rod pattern springs, including roller and roller plate fixed in repairs complete 161 supply and fixed in repair of aluminium body door cill upto 1mtr length at bottom part of door to stop entry of insect inside the room complete all as specified and as directed. 162 supply and fixingin repairs galvanized mild steelwire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tack or galvanised wire staple complete. 163 material and labour for applying two coats of synthetic enamel paint over a coat of pink primer including prepration of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed. 164 material and labour for preparation of old wooden surface and applying two coat of synthetic enamel paint, complete all as specified and as directed. 165 supply and fixed joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. ( cut to ordinary lengthsi.e. within 20mm of the length indicated in fe 410 w ( gdee 250 ) quality a, complete all as specified and as directed. 166 material and labour for preparation of new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer exposed to view surfaces complete all as specified and as directed 167 material and labour for preparation of old steel surfaces of any description not otherwise described over 10cm width or grith and applying one coats of synthetic enamel paint overcomplete all as specified and as directed. 168 taking down existing cement plaster / roof treatment including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed. 169 brushing neat cement slurry with 3.0 kg of cement per sqm complete all as specified and as directed. 170 material and labour for providing cement concrete type bo ( 1:2:4 ) 12.5 mm graded stone aggregate for providing slope, maintain level , roof kerbs or mud stops rounded or chamfered edges, complete all as specified and as directed. 171 material and labour for 10 mm thick cement screed bed or beding layer / plaster in cement ( 1:4 ) mixed with water proofing compound on concrete roof surface, complete all as specified and directed. 172 material and labour app based polymeric membrane minimum wieghing 3kg / sqm and minimum 3 mm thick reinforced with polyster non wove fabric ( weight not less than 150 gms / sqm ) laid over a coat of hot bitumen 85 / 25@ 1.20 kg per sqm by torch application , including a coat of aluminium paint applied on mambrane, complete all as specified and as directed. 173 demolition of brickwork or stone / boulder masonary, built in cement mortar or cement lime mortar, complete all as specified and as directed. 174 demolition of old u / s rcc water tanks of capacity exc 250 litre but not exceeding 500 litre and removing from site, complete all as specified and as directed. 175 disconnecting existing water tank for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of tank exc 250 ltr and not exc 500 ltr capacity, setting aside ( or lowering if required ) for repairs, cleaning, etc. and hoisting if required reconnecting and re fixing in position, complete all as specified and as directed. 176 material and labour for brick work with subclass b bricks, straight or curved on plan exc 6 m mean radius , buit in cement mortar ( 1:6 ) , complete all as specified and directed. 177 material and labour for brick work with subclass b bricks, straight or curved on plan to anybradius in half brick thick wall, buit in cement mortar ( 1:4 ) , complete all as specified and directed. 178 internal electrification works 179 taking down carefully copper / aluminium point wiring including ( light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, batten holders, shades conical fan regulators, light or power sockets etc ) including taking down carefully by unscrewing from boards / outlet / dbs / fittings such as switches, sockets, lamp holders, brackets, ceiling fittings, bulkhead fittings, sketch fittings, tube light fittinfs, fan regulator electric metre box any type etc as directed by by engr in charge. all the removed material to be deposited in age e / m store yard or will be handed over to the contractor under schedule of credit and making good to disturbed surfaces by plastering and two cats of distamper, complete all as specified and as directed. note each item of fittings / fixtures are to be are to be considered as one unit. 180 supply and fix concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor pvc insulated and unsheathedcable 1100 volts grade drawn through and including non metallic rigid pvc conduit, medium grade minimum 19mm dia isi marked and conduit accessories fixed concealed in wall / ceiling / roof etc with sunken type pressed steel / welded ms terminal boxes made out of 1.6 mm ms sheet, 3mm thick laminated sheath top cover for mounting of fittings, switches, sockets outlets, regulators etc complete including provisining of 1.5 sqmm pvc insulatedunsheathedcable 1100 volt grade with multi stranded copper conductor to common earth and connected to earth dolly, complete all as specified and as directed. 181 one light / fan point controlled by one switch 6 amp one way, complete all as specified and directed. 182 one 3 pin switch socket combination 6 amp on the independent board, complete all as specified and directed. 183 one 3 pinswitch socket combination on same board with other switches, complete all as specified and directed. 184 one bell point controlled by one switch 6 amp one way, complete all as specified and directed. 185 one light point controlled by two 2 way switch, complete all as specified and directed. 186 all as described above but point wiring with 2.5 sqmm single core multi stranded copper conductor pvc insulated & unsheathedcable 1100 volt grade and 1.5 sqmm pvc insulated and unsheathed cable 1100 volt grade with multi stranded copper conductor for earth wire for 15 / 16 amp multi purpose socket combination point on independent board, complete all as specified and directed. 187 material and labour for modular switch 1 way 6 amp one module, complete all as specified and directed. 188 material and labour for modular switch 2 way 6 amp one module, complete all as specified and directed. 189 material and labour for modular bell push switch, 6 amp one module, complete all as specified and directed. 190 material and labour for modular socket 6 amp 2 / 3 pin combined 2 module, complete all as specified and directed. 191 material and labour for modular switch socket combination 16 amp, 6 pin, 3 module, complete all as specified and as directed. 192 material and labour for fan step regulator, 120 w 1 module, complete all as specified and directed. 193 supply and fix bell ding dong ac 230volts single pole, complete all as specified and directed. 194 supply and fix ceiling rose 65x17mm of three terminals pvc / polycarbonate, isolated body, complete all as specified and directed. 195 taking down, dismantling, cleaning, painting and of ceiling fan / ext fan for wiring work and refixing the same with pvc flexible wire 3 core with copper conductor 0.5 sqmm upto connector / ceiling rose, complete all as specified and directed. 196 supply and fix 1x18 watt 220v, 4 feet ac deorative box type with driver holder including led tube light connecting up with three core copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by engr in charge. 197 supply and fix 1x18 watt 220v, 2 feet ac deorative box type with driver holder including led tube light connecting up with three core copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by engr in charge. 198 supply and fixing led street light / security light 35 / 36 watt ip 65 complete with suitable size gi bracket and ms clamp to fix it on wall including connecting up with three core copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by engr in charge. 199 material and labour for submain wiring with 2 runs of copper conductor pvc insulated unsheathed cable 1100 volt grade 4 sqmm drawn through pvc conduit medium grade isi marked25mm dia as per is specification fixed concealedin wall / ceiling including conduit and conduit accessories and incl provn of pvc insulated 4 sqmm multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old and making good to the disturbed surface by plastering and two coat of distamper all as directed at site, complete all as specified and directed.note : two runs of 4 sqmm cable alongwith one run of 2 sqmm pvc insulated unsheathedcopper conductor as earth wire, conduitand conduit accessories will be measured as one length. 200 material and labour for submain wiring with 4 runs of copper conductor pvc insulated unsheathed cable 1100 volt grade 6 sqmm drawn through pvc conduit medium grade isi marked25mm dia as per is specification fixed concealedin wall / ceiling including conduit and conduit accessories and incl provn of pvc insulated 2 runs of 6 sqmm multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old and making good to the disturbed surface by plastering and two coat of distamper all as directed at site, complete all as specified and directed.note : two runs of 6 sqmm cable alongwith one run of 4 sqmm pvc insulated unsheathedcopper conductor as earth wire, conduitand conduit accessories will be measured as one length. 201 supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb of 20 amps capacity, complete all as specified and directed. 202 supply and fix mcb db tpn 4 way vertical type factory made ip 42 protection class metal double door with 200 amp rating bus bar 240 / 430 v for fixing of mcbs / insulator / rccbs etc complete after dismantling old one, complete all as specified and directed. 203 supply and fix mcb db tpn 8 way vertical type factory made ip 42 protection class metal double door with 200 amp rating bus bar 240 / 430 v for fixing of mcbs / insulator / rccbs etc complete after dismantling old one, complete all as specified and directed. 204 supply and fix mcbs 240 / 415 volts 10 ka finger proof terminal, c curve bi connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, isi markedto be fixed on db .note: db will be measured and paid separately under respective items of sch a. 205 mcb tpn 63 amps. 206 mcb tpn 100 amps 207 mcb spn 40 amps. 208 mcb sp 5 to 32 amps 209 material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected toand includinggalvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means ofnuts and bolts, check nuts and washers of gi and connected to earhing test point and earth dollyall as shown in electrical plate no 3 of mes ssr part i and testing on completion includingnecessary excavation and earth work in any type of soil, pcc ( 1:3:6 ) type c1 chamber, pre cast rcc slab 50mm thic in cement concrete ( 1:2:4 ) , type b1, reinforced with welded steel wire fabric or xpm, ( weight not less than 4 kg per sqm ) with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, gi protection pipe, 15mm dia, light grade, 7.5 mtr long for protection of earth lead upto test point etc, complete all as specified and as directed. 210 supply & fix exhaust fan ac single phase 230 v of size 300 mm sweep with louvermetalic body complete by making hole of proper size on existing 9 inch thick brick wall for fixing of exhaust fan, making good the disturbed surface and replstering, repainting the wall surface to match the existing colour, complete all as specified and as directed. 211 supply & fix water heater storage type electric, capacity 25 litres bee 5 star rated with 100 % copper tanks on existing brick wall with help of 04 nos fashners nuts and bolts and making neccesary electric & water connection with 02 nos 300mm long pvc connection with 02 nos brass nuts for connection, complete all as specified and directed. 212 material and labour for meter box of size 0.75 mx0.60 m of .30 m width of ms sheet of 3 mm thickness and a clamping or supporting sheet inside forsuppoting of 4 nos meter and door with 1 nos of transparent glass of 5 mm thicknesssuitable for visibility of 4 nos meter fixed on door with suitable arrangemnets. there should be 8 nos holefor entering of 25 mm dia pipe, meter box shall be fixed in wall and necessary chiseling and meke good of wall to be included in quoted cost drawing of meter box to be approved by ge. 213 disconnecting electricconnection and taking downcarefully energy meter and make proper detail with qtr no having meter serial no and reading while takin down energy meter & depositedto age e / m storeyard andrefixing energy meter in meter box with qtr no wrtitten on meter by black permanet markerall as specified and directed by engr in charge. 214 disconnecting electric and water connection connection and taking downcarefully geyser and depositedto age e / m storeyard andrefixing geyser at same location all as specified and directed by engr in charge. 215 material and labour for replacement of rusted louvers of existing exhaust fan fans 300 mm sweep with new gi louvers, complete all as specified and directed. 216 material and labour for taking down carefully led tube light fitting cleaning and kept in safe custody and refix the same as directed by providing necessary connection copper 3 core wire from ceiling rose to tube light fitting, complete all as specified and directed. 217 external electrification works 218 supply, laying, testing and commissioning in trenches / ducts, fixed on walls / panels of xlpe ltug cable, 1100 volts grade, pvc insulated, pvc unsheathed armoured with aluminum conductorcable complete including lugs ofcross sectional areas of cables size 35 sqmm 3.5 coreincluding taking down old unserviceable cable complete all as directed. 219 supply, laying, testing and commissioning in trenches / ducts, fixed on walls / panels of xlpe ltug cable, 1100 volts grade, pvc insulated, pvc unsheathed armoured with aluminum conductorcable complete including lugs ofcross sectional areas of cables size 25 sqmm 4 coreincluding taking down old unserviceable cable complete all as directed. 220 excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft loose soil for foundation of poles, structures, stay rods, laying of underground cable etc complete all as directed. 221 returning, filling in, including spreading, leveling, watering and well ramming in layers each not exceeding 25cm thick using soil complete all as directed. 222 removing excavated surplussoil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as directed. 223 supply and spreading of natural, clean, dry, river sand in trenches for cable protection / transformer yard / two pole structure yardcomplete all as directed.note: punned thickness only shall be measured for payment purpose. 224 supplying and laying un reinforced precast concrete cable cover, class lv, type 1 with peak, size300mm x 180mm x 40mm, complete all as specified and as directed. 225 supply and lay gi tubing 50mm dia, light grade for cable protection at road crossing / on poles and tubing sealed at bith ends after laying the cables including taking out old gi tubing, complete all as specified and as directed. 226 external water supply works 227 taking out old unserviceable gi pipe line and supply and fixing / laying gi tubing medium grade of following dia, laid in trenches / floors or fixed to walls including necessary gi fittingssuch as bends, elbows, nipple, sockets, unions, reducers, tees etc and making good the surface to match with existing surface, complete all as speified and as directed .note : necessary excavation and earth work shall be measured and paid separately under relavent items. 228 supply and fix gun metal gate valves isi marked with iron wheel head and both ends screwed including removing of unserviceable gun metal gate valve from the existing position of the following size 25mm dia gun metal valves, complete all as speified and as directed . 229 excavation in trenches, not exceeding 1.5mm wide and not exceeding 1.5m in depth for laying of pipe line and getting out in any type of soil, complete all as speified and as directed . 230 returning filling in, including spreading, levelling watering and well ramming in layers not exceeding 25cm thick using soil, complete all as speified and as directed . 231 removal of excavated soil to a distance not exceeding 50mtr and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as speified and as directed . 232 cutting of xisting steel tubing pipe for altration or addition ( each cut ) up 50 m bore pipe, complete all as speified and as directed ....

Military Engineer Services - Punjab

40154915 tender for repair / replacement of unsv wiring and allied works at mil stn beas under ge kapurthala.; 1 taking down carefully aluminium / copper point wiring ( light, fan, socket, powerpoint ) including batten, conduit and fittings such as switches, ceiling rose, sockets, brackets, light fittings, switch board etc, making good distrubed surfaces of wall, floar, ceiling etc complete all as specified & directed by engr in charge. 2 m&l for point wiring for controlled by one switch with pvc unsheathed single core multistranded copper conductor cable of size 1.5 sqmm ( nominal area ) in and including pvc conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in cm1:3and to the original specification and pvc casing capping on ceiling for steel structure / surface conduit with clamps, gutties etc for rcc ceiling with including cast iron / pressed steel terminal boxes including providing new 3 mm thick plastic laminatedsheet cover ( hylum ) including one run of pvc insulated frls copper conductor cable of 1.5 sqmm with green insulation as earth dolly complete all as specified and directed by engr in charge for one light point controlled by one way switch. 3 all as per ser item no 2 but one fan point controlled by one, one way switch 4 all as per ser item no 2 but one socket outlet 3 pin, 5 amp on independent board 5 all as per ser item no 2 but one socket outlet 3 pin, 5 amp on same board. 6 all as per ser item no 2 butone bell point controlled by one bell push 7 all as per ser item no 2 butone light point controlled by two, 2 way switch with cable 1.5 sqmm size 8 m&l for point wiring for controlled by one switch with pvc unsheathed single core multistranded copper conductor cable of size 2.5 sqmm ( nominal area ) in and including pvc conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in cm1:3and to the original specification and pvc casing capping on ceiling for steel structure / surface conduit with clamps, gutties etc for rcc ceiling with including cast iron / pressed steel terminal boxes including providing new 3 mm thick plastic laminatedsheet cover ( hylum ) including one run of pvc insulated frls copper conductor cable of 1.5 sqmm with green insulation as earth dolly for 6 pin, 16 amps sockets outlet on independent board complete all as specified and directed by engr in charge. 9 all as per ser item no 8 but one socket outlet 3 pin, 16 amp on same board. 10 s&f switch piano type policarbonate single pole one way 6 amp ( isi marked ) make : havells / schnider / legrand. 11 s&f switch piano type policarbonate two way 6 amp ( isi marked ) make : havells / schnider / legrand. 12 s&f switch bell push 6 pin, 16 amps, flush button type, polycarbonate , sp, one way 230 volts. 13 s&f switch bell push 6 amps, flush type polycarbonate, sp one way 230 volts including taking down unservicable. make : havells / schnieder / legrand. 14 s&f socket out let multipurpose 5 pin, 16 amps, flush type, polycarbonate, 230 / 240 volts including taking down unservicable. make : havells / schnieder / legrand. 15 s&f socket out let multipurpose 5 pin, 16 amps, flush type, polycarbonate, 230 / 240 including taking down unservicable make : havells / schnieder / legrand. 16 s&f stepped type electroni fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directedby engr in charge. make : havells / schnieder / legrand. 17 s&f in replacement of exhaust fan made of study engineering plastic complete wih louvers shutter, voltage 230v, 50hz, rpm 1200, copper winding of sweep 250m complete including taking down unsv exhaust fan of any size and deposit to mes store yard complete all as specified and directedby engr in charge. 18 taking down old unservicale holder and supply and fix angular holder insulated body with back plate suitable for batten fittings complete all as specified and directedby engr in charge. make : bajaj, phillips / havells / cropton / polycab. 19 taking down old unsv laminated sheet and s&f laminated sheet 8 x 4 including fix the switch, socket, regulator retrive from old sheet to new laminated sheet, including m&l for screws, nuts bolts etc complete all as specified and directedby engr in charge. 20 s&f in repairled bulk head fitting 10 watthighly cost effective compact, ultra low energy, modern design utility bulkhead suitable for indoor and outdoor applications with ip 65 protection cat part no lbh 10 cdlof make : crompton or equivalent in syska / philips / bajajwatt complete with all accessories and connecting up complete with 3 core flexible cable white of size 23 / 0.0076 complete all as specified and directedby engr in charge. 21 taking down old us mcb db and s&f in repair sheet metal enclosure for mcb db double door single pole & neutral 4 way with 200 amps rated bus bar complete all as specified and directedby engr in charge. make : legrand / l&t / havells. 22 taking down old us mcb db and s & f in repair sheet metal enclosure for mcb db double door single pole & neutral 8 way with 200 amps rated bus bar complete all as specified and directedby engr in charge. make : legrand / l&t / havells. 23 taking down old us mcb db and s & f in repair sheet metal enclosure for mcb db double door triple pole & neutral 4 way with 200 amps rated bus bar complete all as specified and directedby engr in charge. make : legrand / l&t / havells. 24 taking down old unsv mcb and supply and fixing amp rating 240v, 10ka c curve miniature circuit breaker ( mcb ) of following poles and current carrying capacity in the mcb db complete with connection testing and commissioning complete all as specified and directedby engr in charge. make : legrand / schneider / siemens / c&s 25 ( i ) sp 6 to 32 amp ? 26 ( ii ) spn 32 amp ? 27 ( iii ) spn 40 to 63 amp 28 taking down old unsv mcb andsupply and fixing 415v 10ka c curve miniature circuit breaker ( mcb ) of following poles and current carrying capacity in the db complete with connection testing and commissioning complete all as specified and directedby engr in charge. make : legrand / schneider / siemens / c&s 29 ( i ) tp 25 to 63 amp ? 30 ( ii ) tpn 16 to 32 amp ? 31 ( iii ) tpn 40 to 100 amp 32 taking down old unservicable electric energ meter, supply and fix single phase electronic meter temper proof lcd display with polycarbonate cover 2.30 v, 10 60 amps, accuracy class i 50hz, conforming to is 13779, ip 54 with parameters to show data, time, current reading, load pf, voltage and kwh complete all as specified and directedby engr in charge.make : hpl / l&t / schneider. 33 taking down old unservicable electric energy meter, supply and fix single phase electronic meters temper proof lcd display with polycarbonate cover 440v, 10 60amps, accuracy class i 50 hz, conforming to is 13779, ip 54, with parameters to shwo data, time, current reading, load, pf, voltage and kwh complete all as specified and directedby engr in charge.make : hpl / l&t / schneider. 34 preparing old painted steel surface of meter boxesof any size, including hings all exposed outer surfaces of steel items fixed with the box, without dismantling and m&l for painting with one coat of synthetic enamel paint on exposed steel outer surfaces and writing qtr nos complete all as specified and directedby engr in charge. 35 taking down old unservicable sub main wiring and m&l for submain wiring with 2 single core pvc insulated unsheathed multi stranded copper conductor frls wire 4.00 sqmm 1100 volts grade including and 2.50 sqmm pvc insulated multi stranded, unsheated copper wire green in colour as earthing lead drawn through in pvc rigid conduit of suitable size complete all as specified and directedby engr in charge.note: two run of 4.0 sqmm cable and one run of 2.50 sqmm cable as earth continuity conductor shall be measured & paid as one unit. 36 taking down old unservicable sub main wiring and m&l for submain wiring with 2 single core pvc insulated unsheated multi stranded copper conductor frls wire 6.00 sqmm 1100 volts grade including and 4 sqmm pvc insulated, multi stranded, unsheadted copper wire green in colour as earthing lead drawn through in pvc rigid conduit of suitable size complete all as specified and directedby engr in charge.note: two run of 10 sqmm cable and one run of 6 sqmm cable as earth continuity conductor shall be measured & paid as one unit. 37 taking down old unserviceable sub main wiring and m&l for submain wiring with 2 single core pvc insulated unsheathed multi stranded copper conductor frls wire 10 sqmm 1100 volts grade including and 6 sqmm pvc insulated multi stranded unsheathed copper wire green in colour as earthing lead drawn through in pvc rigid conduit of suitable size complete all as specified and directedby engr in charge.note: two run of 10 sqmm cable and one run of 6 sqmm cable as earth continuity conductor shall be measured & paid as one unit. 38 taking down old unservicable sub main wiring and m&l for submain wiring with 4 single core pvc insulated unsheathed multi stranded copper conductor frls wire 6 sqmm 1100 volts grade and 6 sqmm pvc insulated multi stranded, unsheated copper wire green in colour as earthing lead drawn through in pvc rigid conduit of suitable size complete all as specified and directedby engr in charge.note: four run of 6 sqmm cable and one run of 4 sqmm cable as earth continuity conductor shall be measured & paid as one unit. 39 taking down old unservicable ftl fitting 36 / 40 watt and s&f surface mounting energy saving led tube light fitting, 1 x 20 w, 230v, high efficiency pmma diffuser gives soft glare free light with led tube rod 20w ( white ) complete with all accessories complete all as specified and directedby engr in charge. make : crompton / philips / bajaj / havells. 40 taking down old unservicable ftl fitting 36 / 40 watt and s&f surface mounting energy saving led tube light fitting, 1 x 20 w, 230v, high efficiency pmma diffuser gives soft glare free light with led tube rod 20w ( white ) complete all as specified and directedby engr in charge. make : crompton / philips / bajaj / havells. 41 supply down old unservicable ftl fiting 36 / 40 watt and s&f surface mounting energy efficent led light fittig 2 feet, 1 x 20 w, 230v, compact batten with extruded aluminium chanel complete with all accessories complete all as specified and directedby engr in charge. make : havells part no phexarp71n1w020 42 s&f in repair metal flush mounting box of 6 module complete all as specified and directedby engr in charge. make: legrand / siemens / crabtree / havells. 43 taking down old unservicable ftl fitting 36 / 40 watt and s&f surface mounting energy efficient led light 2 feet, 1 x 20 w 230 v, compact batten with extruded aluminium chanel complete with all accessories complete all as specified and directedby engr in charge. 44 s&f wall mounting lights fixture made up of polycarbonate, suitable for 9 w retrofit led lamp b22 base complete all as specified and directedby engr in charge product code lhdl031600990 ( city 3 ) of havells or equivalent in bajaj / crompton / polycab / phillips . 45 m&l for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground ( earth pit not less than 2.25 metre deep below ground level ) with top edge of plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts check nuts and ashers of galvanized iron or steel all as shown in electrical plate no 3 of mes ssr part i connected to main switch board or main control board all as specified and testing on compltion inclduing provision of earth wireprotected by galvanized iron 15 mm dia light grade pipe an watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil pcc pit with re cast rcc cover, charcoal, salt, funnel etc complete all as specified and directedby engr in charge. 46 excavation in trenches in soft / loos soil not exceeding 1.50 mtr wide and not excedding 1.50 mtr in depth for taking out old cable / laying of under ground cable / foundation of poles / satys including segregation of old servicable bricks complete all as specified and directedby engr in charge. 47 returning filling in including spreading levelling waterin and well ramming inlayers not exceeding 25 cm thick each layer complete all as specified and directed by engr in charge. 48 removal of surplus soil to a distance not exceeding 50 mtr away and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directedby engr in charge. 49 m&l for brick protection using old size sub class b bricks, laid flat dry but adjoining to each other laid length wise prependicualr to the exist of cable complete all as specified and directedby engr in charge. 50 supply filling in trenches spreading, levelling sand cushioning 8 cm below and 15 cm above the cable for under ground cable complete all as specified and directedby engr in charge. 51 supply and laying in replacement gi pipe light grade 50 mm bore for cable protection fixed to poles / along wall / floor / under road / preparation of gi bracket etc across the darain or nallah with clamps. bolts nuts & washers etc complete all as specified and directedby engr in charge including taking down the old unservicable ( clamps, bolths, nuts & washers shalll be measured and paid sepeartey ) . 52 s&f 1100 volts grade heavy duty cable pvc insulated stranded aluminium condutor, served with inner sheathing of pvc tape and overall pvc sheathed in service connections suspended by insulting hangers not more than 1 meter aprat including 4 mm suspension wire, on twin core cable flat or round of 10 sqmm cable complete all as specified and directedby engr in charge. 53 supply laying commisioning and testing xlple insulated armoured heavy duty, electric cable with standed conductor for working 1100 voltage grade size 2 core 16 sqmm including taking unservicable cable complete all as specified and directedby engr in charge ( earth work, and cushioning and brick protection shall be measured and paid for separately ) . 54 all as per item ser no 47 above here in before but 4 core 25 sqmm 55 all as per item ser no 47 above here in before but 3.5 core 35 sqmm...

Military Engineer Services - Punjab

39895945 provision of deficient charging shop and baggage room under ge ( north ) at mil stnpatiala; 1 schedule asection i ( building works ) 2 total amount of sch a sec i ( building works ) 3 schedule asection ii ( excavation and earth works ) 4 total amount of sch a sec ii ( excavation and earth works ) 5 schedule asection iii ( internal water supply ) 6 total amount of sch a sec iii ( internal water supply works ) 7 schedule asection iv ( misc items of works ) note :this schedule is not pre priced by mes and the pre priced rate indicated as rs 0.00 under col. 5 siginifies this fact only. 8 material & labour for point wiring with1.50 sqmm in copper conductor cable ( multistrand ) frls single core pvc insulated cable in and including pvcconcealed conduit ( isi marked ) of heavy duty required size with all accessories ie pvc gutties etc terminated insunken / pressed metal flush box and white modular cover plate with frame for mounting of switches / sockets / fan regulators etc and continuous earth wire 1.5 sqmm copper cable pvc insulated frls controlled by one switch for one light / fan / sockets point / all as specified and directed by engr in charg note : i ) eye / bottle thimbles shall be used for connection in switches / sockets & mcbs in dbs without any extra cost ii ) electric rewiring should be done in proper colour coding i.e. red for phase, black for neutral and green for earth.iii ) neccessary cutting chasing wherever required shall be part of job at no extra cost. 9 one light / bell / fan point ( ceiling / wall / exhaust ) controlled by one 1 way switch or 1 one way switch and regulator 10 one 3 / 5 pin socket outlet, 5 / 6 amp on same board with other switch 11 one 3 / 5 pin socket outlet, 5 / 6 amp on independent board 12 all as per ser no 5 above but one socket outlet 3 pin 15 amp independent with 2.5 sqmm wire including 2.5sqmm pvc insulated and unsheathed frls single core stranded copper earth continuity conductor complete 13 supply and fix modular switch one way 6 amp, 240 volts, 1 module 14 supply and fix modular switch one way 16 amp, 240 volts, 1 module 15 supply and fix modular socket outlet6 amp, 2 / 3 pin combined 2 module 16 supply and fix modular socket outlet6 / 16 amp, 2 / 3 pin combined 2 module 17 supply and fix ceiling rose surface bakelite tow tothree terminal 65x50mm 18 supply and fix new generation energy saving and environmental friendly long life led building security light 1x25 watts made up of pressure die cast alluminium housing with high power led as light source and lense embedded pc cover having top opening separate driver compartment with ip65 protection and impact resistance of ik07, with all accessories including suitable bracket with 32mm bore light grade gi pipe bend to shape, including ms clamp of size of required size and pvc cable 1.5 sqmm twin core from ceiling rose / pole to light fittings complete all as specified and directed by engineer in charge. 19 supply and fix surface mounted led bulk head luminaire of capacity 10 watt with abs body & polycarbonate diffuser, ip54 inc connection with , with flexible wire 0.5 sqmm copper cable all as specified & directed by engr in charge. 20 supply and fixsheet metal enclosure 4 ways double door for dbs when mcbs areto be used 240, volts including 200 amps standard bus bar of suitable size and common neutral link allflush mounting type, drilling holes for incoming and out going cables with ip 54 protection complete all as specified & directed byengr in charge. 21 supply and fixsheet metal enclosure 8 ways double door for dbs when mcbs areto be used 240, volts including 200 amps standard bus bar of suitable size and common neutral link allflush mounting type, drilling holes for incoming and out going cables with ip 54 protection complete all as specified & directed byengr in charge. 22 supply and fix mcb , spn, 240 volts , 32 40 amp for fixing in dbs ofincluding proper thimble connections complete all as specified and directed by engineer in charge. 23 supply and fix mcb , spn, 240 volts , 63 amp for fixing in dbs ofincluding proper thimble connections complete all as specified and directed by engineer in charge. 24 supply and fix mcb, single pole 240 volts 6 to 32 amp capacity for fixing in db’s including proper thimble connections complete all as specified and directed by engineer in charge. 25 material & labour for earthing complete with galvanized iron earth plate electrode of size 600x600x6.0mm , buried directly in ground ( earth pit not less than 2.25 mtrs below normal ground level ) with top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts , nuts , check nuts and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate 20 mm dia watering pipe medium grade 1.70 mtr long with a plug at top, gi protection pipe light grade 15 mm dia from earth pit to main board including pcc pit in cement concrete 1:2:4 along with ci frame and cover 10mm thick duly hinged to ci frame as shown in the electrical plate no3 of ssr 2009 part 1 26 supply and fixsurface mounted led luminaire 36 watt suitable for grid celling cutout dimensions: 2x2 ft. incl connecting with twin core copper wire from ceiling rose to fitting, fixture size: ( lxwxh ) in ( 595x595x65 ) mm incl lamp and driver all as specified & directed 27 supply and fix exhaust fan ac single phase 230 / 240 v of size 450 mm sweep 900 rpm metal body air delivery in cfm 2567, high efficiency motor, dynamically balanced blade for better performance and corrosion resistant powder coated metallic finish including louver , making holes & grouting nut boltscomplete all as specified and directedby engineer in charge. 28 ceiling fan with bldc technology ac single phase 240 volt 50 hz of size 1200 mm sweep complete in white colour having service value more than or equal to 6 with canopy, hanging rod and all accessories incl nut, bolts, clamps etc. icluding making connections with twisted 3 core pvc insulated unsheathed flexible cord of 0.75 sqmm copper conductor from ceiling rose to ceiling fan complete all as specified and directed. 29 supply and fix led tube light fitting 1x20 / 22 w suspended box type provides uniquely clean & simple lighting system offering continuous, uniform lines of light across ceiling, aluminlum extruded suspended light gives continous lines of light distribution fixture size : ( lxwxh ) in ( 1175x38x66 ) mm incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed by engr in charge. 30 sub main wiring with two single core 6.0 sqmm pvc insulated and unsheathed frlsh, stranded copper conductor cable drawn through pvc concealed conduit 25 mm dia including 6.0 sqmm pvc insulated unsheathed frlsh stranded copper conductor cable as earth wire all as specified and directed by engineer in charge. note 1: 2 ( two ) runs of 6.00 sqmm copper conductor cable, 1 run of pvc conduit & 1 run of 6.00 sqm copper conductor earth wire shall be measured as one unit ) note 2 : ( i ) rate quoted for this items shall be inclusive of the cost of ( i ) rigid non metallic pvc conduit of 25 mm dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. ( ii ) cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces and cutting not exc.10 cm girth . 31 supply & fix tube light fitting self ballasted led batten, extruded thermoplastic body with pc diffuser in square led batten 18 / 20w 6500k of capacity, 20 watt, 4 ft long incl 3 core flexible wire 0.5 sqmn copper cable all as specified and directed by engr in charge. 32 supply and fix tubes light grade galvanised40 mm bore, galvanized with all fittingslaid in trenches or on ground fixed to wall and ceiling or floors for passing through of cable complete all as specified and directed by engineer in charge. ( excavation and earth work measured and paid seperately ) .. 33 supplied and laid xlpe insulated , screened, pvc bedded, galvanized steel wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 10 sq mm 2 corecomplete all as specified & directedby engineer in charge. 34 supplied and laid xlpe insulated , screened, pvc bedded, galvanized steel wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 25 sq mm 2 corecomplete all as specified & directedby engineer in charge. 35 sandcushioningwith clean dry sandto cables with layer of sand 8cm before laying of cable and 15cm thick after laying of cablecomplete all as specified.note : for payment purpose punned thickness of 18cm shall be measured against spread thickness of 23cm as mentioned in para 19.75 of ssr part i. 36 un reinforced pre cast concrete cable covers conforming to is 5820 1970, class lv, type 1 flat of size 250mm x 150mm x 40mm laid in trenches as protection to cables complete all as specified and as directed....

Patiala Locomotive Works - Punjab

39657254 supply of set of lead wires for hitachi tm stator of tm type hs 15250a ( one set consisting of following ) : ( 1 ) lead wire a, to drg.no.3twd.095.067, qty 01 no. ( 2 ) lead wire to drg. no..3twd.095.069, alt 1, qty 01 no. ( 3 ) lead wire aa to drg.no.3twd.095.068, alt 1, qty 01 no. ( 4 ) lead wire f to drg.no.3twd.095.073, alt 1, qty 01 no. ( 5 ) lead wire ff, drg.no.3twd.095.074, alt 2, qty 01 no. ( 6 ) lead wire to drg.no. 3twd.095.071, alt 1 qty 02 nos. ( 7 ) lead wire to drg.no.3twd.095.070, alt 2, qty 02 nos. ( 8 ) lead wire to drg.no. 3twd.095.072, alt 1, qty 01 no. ( 9 ) connector for main pole to drg.no.4twd.092.510, qty 05 nos., confirming to specification no. 4tms / 095 / 028 & e 0028 for hitachi tm type hs 15250a for elect. loco. str no.clw / tm / 9020 rev 0 [ warranty period: 30 months after the date of delivery ] => limited...

Patiala Locomotive Works - Punjab

39550160 supply of set ( motor set ) of mp / cp coils with shoes fully potted, interconnectors and lead wires for hitachi tm stator, type hs 15250a, conforming to clws specification no. 4tms.095.032 alt 4 & 4tms.095.033 alt 4. one motor set consisting of ( 1 ) main pole coil with shoes ( south pole ) drg no. 10s 808 414 rev.d, qty 03 nos. ( 2 ) main pole coil with shoes ( north pole ) drg no.10s 808 415 rev.d, qty 03 nos. ( 3 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 416 rev.d, qty 02 nos. ( 4 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 417 rev.d, qty 01 no. ( 5 ) comm. pole coil with shoes ( north pole ) drg no.10s 808 418 rev.d, qty 02 nos. ( 6 ) comm. pole coil with shoes ( north pole ) drg no. 10s 808 419, rev.d, qty 01 no. lead wire drg no. 3twd.095.067, qty. 1 no., lead wire drg no. 3twd.095.069, alt 1, qty. 1 no., lead wire aa drg no. 3twd.095.068, alt 1, qty. 1 no., lead wire fdrg no. 3twd.095.073, alt 1, qty. 1 no., lead wire ff drg no. 3twd.095.074, alt 2, qty. 1 no., lead wire drg no.3twd.095.071, alt 1, qty.2 nos., lead wire drg no. 3twd.095.070, alt 2, qty. 2 nos., lead wire drg no.3twd.095.072 alt 1, qty 1 no. and connector for main pole drg no. 4twd.092.510, qty 5 nos, to spec. no. 4tms / 095 / 028 or e 0028 & rdso str no. rdso / 2007 / el / str / 023, rev 1 for hitachi traction motor type hs 15250a of electric loco. ] [ warranty period: 30 months after the date of delivery ] ...

Patiala Locomotive Works - Punjab

38113433 supply of set ( motor set ) of mp / cp coils with shoes fully potted, interconnectors and lead wires for hitachi tm stator, type hs 15250a, conforming to clws specification no. 4tms.095.032 alt 4 & 4tms.095.033 alt 4. one motor set consisting of ( 1 ) main pole coil with shoes ( south pole ) drg no. 10s 808 414 rev.d, qty 03 nos. ( 2 ) main pole coil with shoes ( north pole ) drg no.10s 808 415 rev.d, qty 03 nos. ( 3 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 416 rev.d, qty 02 nos. ( 4 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 417 rev.d, qty 01 no. ( 5 ) comm. pole coil with shoes ( north pole ) drg no.10s 808 418 rev.d, qty 02 nos. ( 6 ) comm. pole coil with shoes ( north pole ) drg no. 10s 808 419, rev.d, qty 01 no. lead wire drg no. 3twd.095.067, qty. 1 no., lead wire drg no. 3twd.095.069, alt 1, qty. 1 no., lead wire aa drg no. 3twd.095.068, alt 1, qty. 1 no., lead wire fdrg no. 3twd.095.073, alt 1, qty. 1 no., lead wire ff drg no. 3twd.095.074, alt 2, qty. 1 no., lead wire drg no.3twd.095.071, alt 1, qty.2 nos., lead wire drg no. 3twd.095.070, alt 2, qty. 2 nos., lead wire drg no.3twd.095.072 alt 1, qty 1 no. and connector for main pole drg no. 4twd.092.510, qty 5 nos, to spec. no. 4tms / 095 / 028 or e 0028 & rdso str no. rdso / 2007 / el / str / 023, rev 1 for hitachi traction motor type hs 15250a of electric loco. ] [ warranty period: 30 months after the date of delivery ] ...

Military Engineer Services - Punjab

35724560 tender for provision of religious institute hall ( sarv dharmstal ) under ge ( n ) bathinda at bathinda mil station lump sum price worked out by the contractor for “building / structure work” as listed in schedule ‘a’ part iabove / below the lump sum price inserted by the mes against this schedule under col 6. 3 schedule a part ii ( earth work ) 4 lump sum price worked out by the contractor for “earth works” as listed in schedule ‘a’ part iiabove / below the lump sum price inserted by the mes against this schedule under col 6. 5 schedule a part iii ( external water supply ) 6 lump sum price worked out by the contractor for “external water supply works” as listed in schedule ‘a’ part iiiabove / below the lump sum price inserted by the mes against this schedule under col 6. 7 schedule a part iv ( internal electric supply ) 8 lump sum price worked out by the contractor for “internal electric supply works” as listed in schedule ‘a’ part ivabove / below the lump sum price inserted by the mes against this schedule under col 6. 9 schedule a part v ( external electric supply ) 10 lump sum price worked out by the contractor for “external electric supply works” as listed in schedule ‘a’ part v ( section a ) above / below the lump sum price inserted by the mes against this schedule under col 6. 11 schedule a part vi ( misc works ) 12 m & l for construction of valve pit type b of size 60cm x 60 cm x 60 cm ( internal dimension ) of brick masonry laid with cement mortar ( 1:4 ) including cover of ms sheet 3.15 mm thick and angle iron frame 50mmx 50mmx 6mm with hinges, handle and locking arrangement including painting with two coat of synthetic enamelled paint over a coat of red oxide primer and grouting to pcc 1:2:4 type b 1, using 20mm graded crushed stone aggregates, rendering 15 mm thick in cement mortar 1:3 and three coats of white wash on internal surfaces and external exposed surfaces, foundation concrete 1:3:6 type c 2 using 40 mm graded crushed stone aggregates including necessary earthwork, returning filling, removal complete all as specified and shown on drawings.note: applicable drawing for valve pit is drawing no. btd 811 sheet 1 / 2 to 2 / 2 13 supply, fabricating, installation, testing, commissioning and electrically connecting lt feeder pillar box cubical type of size 60 cm x 40 cm x30 cm , 415 volts, factory made, machine pressed, dust and vermin proof, out door type , made with crca sheet 3.15 mm thick, feeder pillar box shall be powder coated with 7 tank process for treatment of degreasing, pickling & two coats primer, before being given the stove epoxy finish.frontopeningwith single door with provn of rubber beading and locking system, including 200 amp aluminium bus bar set of 4 with provn of hole on bus bar for fixing of cable mounted on pvc / epoxy insulators, including mccb 100 amp, 4 pole, 415 volts rating with breaking capacity 16 ka, adjustable setting = 80 100% and mounted on angle iron legs frame made with angle iron size 25 mm x 25mm x 5 mm and legs duly spray painted internally and externally with tow coats of synthetic enamel paint over a coat of red oxide primer , legs grouted in pcc ( 1:2:4 ) type b 1 ( using 20mm graded crushed stone aggregate ) including necessary earth work complete, including all provn of opening for incoming / outgoing cables and testing complete all as directed by engr in charge.note: the cost of 200 amp aluminium bus bar set of 4 pvc / epoxy insulator and mccb 100 amp , 4 pole , 415 volts rating with breaking capacity 16 ka is included in this item and nothing shall be paid extra on this account. 14 m & l for making the hole under road and hard standing not less than 1 metre depth and suitable for laying and inserting pipe upto 80 mm dia any length by mechanical drill system or auger system and making the surface good as per existing surface complete all as specifed and directed. note: gi tubing shall be measured and paid separately. 15 m & l for earthing complete with galvanized iron or steelearth plateelectrode of size 60 cm x 60cm x 6.0mm thick buried directly in ground, vertically to a depth not less than 2.25 mtr below normal ground level with top edge of earth plate at depth of not less than 1.5 mtr below normal ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to galvanized earth lead wire 4.0 mm dia by means of gi bolts, nuts washers & check nuts and washers of gi ( including making of test point withgalvanized earth lead wire 4.0 mm dia including gi protection pipe 20 mm bore light grade for protection of gi wire to the extent of 7.5 mtr all as directed, gi pipe light grade 20 mm bore for watering including providing funnel and wire mesh, gi frame with suitably reinforced rcc pit cover, pcc chamber pit with pcc ( 1:3:6 ) type c2 using 40 mm graded stone aggregates complete including excavation and earth work in any type of strata , all as specified and shown in electrical plate no 3 of ssr 2009 part i, pcc pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete all as specified and directed. 16 m & l for earthing complete with galvanized iron or steelearth plateelectrode of size 60 cm x 60cm x 6.0mm thick buried directly in ground, vertically to a depth not less than 2.25 mtr below normal ground level with top edge of earth plate at depth of not less than 1.5 mtr below normal ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to gi earth strip 32 x 6 mm thick by means of gi bolts, nuts washers & check nuts and soldering the strip, electrode connected to panel board or on poles or on transformer ( including making of test point with gi strip of size 32 x 6 mm ) including gi protection pipe 40 mm bore light grade dia for protection of strip upto the extent of 7.5 mtr all as directed, gi pipe light grade 20 mm bore for watering including providing funnel and wire mesh, gi frame with suitably reinforced rcc pit cover, pcc chamber pit with pcc ( 1:3:6 ) type c2 using 40 mm graded stone aggregates complete including excavation and earth work in any type of strata , all as specified and shown in electrical plate no 3 of ssr 2009 part i, pcc pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete all as specified and directed. note: the rate quoted by the contractor shall be deemed to be included of earth strip 32x6mm and pit protection pipe 40mm dia light grade up to 7.5 mtr distance. earth strip beyond 7.5 mtr will be measured and paid separately under relevant items...

Military Engineer Services - Punjab

35302188 upgradation and extension of baffle range at nams ( tender id : 2022_mes_550653_2 ) surface dressing not exceeding 15 cm deep in soft / loose soil completeall as specified & directed. 3 earth work in excavation in all kind of soil by mechanical means ( hydraulic excavator ) over areas ( exceeding 30cm in depth, 1.50 metre in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 metre and lift upto 1.50 metre complete all as specified and directed. 4 all as per srl item no 1.02 above but depth exceeding 1.50 metre and not exceeding 3.00 metre. 5 earth work in excavation by mechanical means ( hydraulic excavator ) / in trenches or drains ( not exceeding 1.5 metre in width or 10 sqm on plan ) , not exceeding 1.5 metre deep including dressing of sides and ramming of bottoms, lift upto 1.5 metre, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metre complete all as specified and directed. 6 all as per srl item no 1.04above but depth exceeding 1.50 metre and not exceeding 3.00 metre. 7 excavating in trenches in soft / loose soil not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth for foundation for pipes, wells, cesspits, manholes, pier holes, cables etc not exceeding 10 sqm on plan and not exceeding 1.50 metre in depth and getting out complete all as specified and directed. 8 all as per srl item no 1.06above but depth exceeding 1.50 metre and not exceeding 3.00 metre. 9 surface excavation not exceeding 30 cm deep and averaging 15 cm deep, getting out in any type of soil complete all as specified and directed. 10 material and labour for approved earth filling in floors / trenches, laid in layers not exceeding 15cm thick spread, levelled and rammed / rolled including watering to required level & gradient complete all as specified and as directed. note : quoted rate shall deemed to be inclusive of supply of earth from outside defence land. 11 returning, filling in, spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each complete all as specified and directed. 12 material and labourfor cement concrete 1:4:8 type d 2 using 40mm gradedstone aggregate as in foundation filling anf mass concrete complete all as specified and directed. 13 material and labour for rcc ( m 25 ) design mixusing 20 mm graded stone aggregate as in foundation including rafts, footings and mass concrete etc complete all as specified andas directed. 14 material and labour for rcctype m 25 ( design mix ) using 20 mm graded stone aggregate in beam, lintels over 1.5m span height for staging upto 9.5m from gl complete all as specified andas directed. 15 material and labour for rcctype m 25 ( design mix ) using 20 mm graded stone aggregate in columns, pillars, posts height for staging upto 9.5m from gl etc complete all as specified andas directed. 16 use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces of concrete, flat, complete all as specified and directed. 17 use and waste of formwork to the sides of pillars, posts, piers, columns and stanchions, square or recatngular or polygonal, rough finished surface of concrete height for staging upto 9.5m from gl complete all as specified. 18 use and waste of form work to sides and soffits of floor or roof beam lintel beam, flat surfaces, support overhanged rough finished surface of concreteheight for staging upto 9.5m from gl complete all as specified and directed. 19 material and labour for mild steel tmtbars 10 mm dia and over, cut to length, ent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed 20 material and labourmild steel reinforcement tmtbars 5 mm dia and over up to and including 10 mm dia. in stirrups, spacers, binders etc.cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 21 m & l for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth not otherwise described for and priming with red oxide primer and applying two coat of synthetic enamel paint over priming coat all as specified and directed. 22 material and labour for rcc m 25 design mix, using 20 mm graded aggregates in walls, retaining walls, basement walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed. 23 material and labour 20mm thick cement plaster 1:4 mixed with recron fibre @ 180gm / bag of cement or as per manufacturer instruction s ( rough finish ) . note: recron fibre will be measured & paid for separately under relevant item here in after. 24 supply only recron fibre complete all as specified and directed. ( recron fibre shall be is marked & shall be approved by ge. 25 removal of excavated spoilto a distanceexceeding 500 metre but not exceeding 1.5 km and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed. 26 supply only 80mm thick bullet resistant fics panel ( slurry infiltrated fibre concrete ) of size 2.0 metre x 1.0 metre ( in three parts as shown on drgs ) ( 0.7m+0.6m+0.7m ) in lining on firing face of baffle wall all as per tbrl design and specifications and baffle range manual ( as amended up to date ) all as per shown in drg.note: ( i ) only tbrl certified makes panels shall be used in work. ( ii ) testing of panel shall all be carried out all as specified in particular specification section ii 27 fixing only of fics panels on baffle wall using 02 nos of hardwood battens of size 2000mmx100mmx35mm at the back of panel and using 06 nos of trutek or equivalent m 20 bolts and nuts of min 300mm length and 30 / 32mm dia / bore galvanised steel sleeve medium grade alongwith hardwood cap as per requirement at site complete all as specified and as shown on drgs. 28 fixing only of fics panels on baffle wall using 02 nos of hardwood battens of size 2000mmx100mmx35mm at the back of panel and using 06 nos of trutek or equivalent m 20 bolts and nuts of min 675mm lengthwith hardwood cap over the exposed faces of bolts of size 100x100mm in existing sleeve complete all as specified and directed by engr in charge. note for item no. 1.26 & 1.27: any other items required for fixing of fics panels shall also be deemed to be included in the quoted rates & nothing extra shall be admissible. 29 material and labour for 30mm thick cement palster 1:3 mixed with recron fibre @ 180gm / bag of cement or manufacturers instructions as specified ( rough finished ) . note: recron fibre shall be measured & paid for separately under relevant items here in before. 30 material & labour for reinforced cement concrete type m 25 design mix using 20 mm graded stone aggregatein stair case including steps complete all as specified andas directed. 31 use and waste of formwork to faces of walls, retaining walls, abutments, parapets & staircase railings and similar work including attached pilasters, buttresses etc vertical or to fair finished complete all as specified and as directed. 32 supply and fixing 2nd class hard wood boarding 30mm thick clean sawn with butt joints with nails is any situation ( except flooring and skirting ) complete all as specified and directed. 33 material and labour for cement plaster 15mm thick on fair faces or other than fair faces of brick work in cement mortar ( 1:4 ) finished even and smooth without using extra cement complete all as specified and as directed 34 material and labour for preparation of newly plastered surface on wall and applying two coats of apexpaint over a coat of alkali resistant primer at a height not exceeding 13m above or below gl in camouflaging pattern complete all as specified and directed. 35 material and labour 200 mm bore dia rcc pipes class np2 complete with collars laid in trenches and testing complete all as specified and directed 36 material and labour for plain cement concrete ( 1:3:6 ) type c 2 using 40mm graded stone aggregate as in bed of 200mm dia rcc pipes including forming cradles after they are laid & tested complete all as specified. 37 material and labour for preparation of new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified. 38 m&l for rcc ( m 25 ) design mix as using 20 mm as in slab supported on walls, beams and columns in floors, roofs, landings, balcony, canopy, deck slab and in shelves and the like complete all as specified andas directed. 39 use and waste of form work to sides and soffits of suspended slabs such as roof slab, landing and similar work complete all as specifed and directed. 40 use and waste of form work to edges of slabs such as roof slab, landing and similar work complete all as specifed and directed. 41 material and laying mild steel frame work as in manhole cover and in hold fast complete welded, hinged or pinned confirming o fe 290 gde e 165 complete all as specified. 42 material and labour for mild steel round deformedbars 16 mm dia and over, cut to length, ent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 09.mm dia or securing with clips complete all as specified and directed 43 material and labour for precast reinforced cement concrete 1:2:4 type b 1 using 20mm graded stone aggregate as in manhole cover and set in cement mortar 1:4 complete all as specified. 44 supply only composite trapezoidal boxes for ground barriers of size 1000mm x ( 700mm front& 650mm back ) x200mm thick all as per details shown on drawings. 45 all as per srl item no 1.43 above but of size 900mmx ( 700mm front and 650mm back ) x200mm thick complete all as per details shown on drawings. note for item no. 1.43 & 1.44: earth filling, stone aggregate & pcc 1:3:6 type c 2 shall be measured & paid for separately under relevant items. 46 material and labour for plain cement concrete 1:3:6 type c 2 using 40mm graded stone aggregate in foundation for fixing of ground barrier boxes complete all as specified. 47 supply and filling graded coarse aggregates of nominal size 10 20mm, for ground barrier boxes including filling all as direced by engr in charge. 48 demolition of cement concrete ( unreinforced ) in ground floors and paving not exceeding 15cm thick ( below or above ground level ) complete all as specified and directed. 49 material and labour for 75mm thick cement concrete 1:2:4 type b 1 using 20mm graded stone aggregate as in sub base of flooring finishing surfaces finished the surface even and smooth without using extra cement complete all as specified and directed. 50 material and labour brick work with fly ash bricks straight or curved on plan exceeding 6.00 mtr mean radius in cement mortar 1:4 including corbelling etc including demolition of old brick work complete all as specified and directed 51 taking down cement plaster from walls / ceilling including raking outjoints, hacking for key scrubbing down with water and dispose off debris upto distance not exceeding 500 m where directed complete all as specified and as directed. 52 supply and fixing ms wire mesh of size 40mmx40mm aperture hole with thickness 2 to 3mm and welding to existing reinforcement in wall / ceiling ( minimum 40 pieces in one sqm ) including necessary fixing arragement like scaffolding, welding machining etc complete all as specifed and as directed. 53 taking down bullet resistant sifcon panel of any thickness size and in any position on baffle wall etc complete all as directed. 54 dismantling off framed work timber scantling 40 sqcm and over in section & in any position completeall as specified. 55 dismantling of reinforced cement concrete of any description & in any position at any depth above or below gl completeall as specified and direced by engr in charge. 56 material and labour for plain cement concrete ( 1:2:4 ) type b 1 using 20mm graded stone aggregate cast in situ in lintels upto 1.5m span, cills and other similar bands, parapets, copings bed plates & like including weathering etc complete allas specified. 57 dismantling structural steel work including members by cutting rivets, removing nuts & bolts complete all as specified and as directed. 58 supply and fixing mild steel work as in framed work such as targets, grills, grating, framed guard bars etc with ends of bars shouldered or rivetted or forged into spikes and similar work conforming to fe 290 gde e 165 complete all as specified and as directed by engr in chrage. 59 supply and fixing in repairs 16mm dia hard drawn twisted steel wire rope fixed in any position including necessary cutting, notching and bolting arrangement complete all as specified and as directed. 60 supply and cast iron work grade fg 150 machined, in pulleys and similar article weight not execeeding 5 kg each complete all as specified. 61 supply and fixing 2nd class hard wood boarding 15mm thick clean sawn with butt joints with nails fixed over ms frame as targets in any situation ( except flooring and skirting ) complete all as specified and directed. 62 supply & fixingmild steel screw bolts ( machine made ) 11 to 15mm dia of shank with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc. 5 but not exc. 10 cm long, complete all as specified and as directed. 63 material and labour for 25mm thick cement concrete 1:2:4 type b 1 using 20 mm graded stone aggergate as in floors or steps and treads finishing cement concrete surface ever and smooth with using extra cement complete all as specified. 64 dismantling of heavy armoured plate of mild steel work of any description fixed with nuts & bolts over stop butt complete all as specified & as directed by engr in charge. 65 fixing only heavy armoured plate of any description with nuts & bolts over stop butt complete all as specified. note: nuts & bolts to be measured & paid separtely under item no 1.61 & 1.76. 66 material for labour 2nd class hard wood wrought in scantlings and fixed in repairs to replace old and decayed timber ( including piecing scarfing etc of old and new timbers if required ) in any shape & place complete all as specified and directed. 67 supply and fixing 25mm thick second class hard wood planks fixed over stop butt with nails, screws etc complete all as specified and as directed. 68 material & labour for earth filling under stop butt approved by ge, earth shall be free from vegetation, aggregate & shall be dry in powder form and filling in embankement complete all as directed by engr in charge.note : quoted rate shall deemed to be inclusive of supply of earth from outside defence land. 69 material & labour for roughening old concrete surfaces of wall / ceiling surfaces by picking, tucking with chiseling, sweeping clean and washing down with water to remove dust etc for baffle wall / side wall / stop butt complete all as specified and directed by engr in charge. 70 supply and fixing ms mesh of mesh of size 25mm and 1.4mm dia wire welding to existing reinforcement in wall / ceiling including necessary fixing arrangement like scaffolding welding machine etc complete all as specified and as directed. 71 material & labour washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 ( 1 cement : 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per sqm, top layer 15mm cement plaser 1:1 / 2:2 ( 1 cement:1 / 2 coarse sand: 2 stone chipping 10mm nominal size ) in panels withgroove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified. 72 material and labour for preparing old plastered surfaces of wall and applying one coat of apex paint at height not exceeding 10mtr from gl in camouflaging pattern over a coat of alkali resistant primer complete all as directed. 73 material and labour brick work with sub class b brick straight or curved on plan to any radius in half brick thick built in cm 1:4 complete all as specified and directed 74 material and labour brick work with sub class b brick straight or curved on plan exceeding 6m mean radiusbuilt in cm 1:6 complete all as specified and directed 75 material and labour for flush pointing to bricks walls in cement mortor 1:3 complete all as directed by engr in charage. 76 extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds stopped ends etc complete all as specified and directed. 77 supply and fixing mild screw botls ( machine made ) 16 to 20mm dia of shank with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc. 22.5 cm but n. exc 30 cm long, complete all as specified and as directed. 78 e / m works 79 material and laying for sub b bricks ( old size ) for cable protection laid flat and dry intrenches over the cable perpendicular to the direction of cable complete all as specified in ssr and directed by engr in charge. 80 mateiral & labour sand cushioning with dry and clean sand in two layers first layers of 80mm thick before laying of cables and second layer of 150mm after laying of cable complete all as specified and directed by engr in charge. note: punned down thickness shall be measured for payment. 81 supply and laying in replacement of lt underground cable xlpe insulated, inner pvc sheathed, galvanized steel strip armoured, pvc sheathed electric power cable with stranded compact aluminium conductor 1100 volts grade 35sqmm 3.5 core suitable for earthed system laid in duct / trench / along pole etc including making connection. note: the cost of aluminium timbles / lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it. 82 all as per srl item no. 2.03 here in after but of size 25 sqmm 4 core 83 all as per srl item no. 2.03 here in after but of size 10 sqmm 2 core 84 supply and fixing in replacement street light fitting bracketmade out of galvanised iron pipe 40mm bore light grade 1.5 mtr long complete with nuts, bolts, washer clamp etc all as specified and directed by engr in charge. 85 supply and fixing in replacement galvanized iron pipe of 50mm bore light grade fixed to poles / walls with nuts, bolts and washers or laid under road crossing complete all as specified and directed. 86 material and labour fabricating and fixing in replacement cross arms ( any type ) supports, bracing, stiffners etc made out of ms channel, angle iron, flat iron of any size including drilling of holes, making clamps, eye hooks, nuts, bolts and washers etc, welding if required including painting with two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed. 87 supply and fixing in replacement pin / disc type procelain vitreous white, brown or green insulator including one galvanized mild steel straps, washers and nuts for 1100 volts grade, including removal of existing insulators complete all as specified and directed. 88 material and labour in replacement for acsr conductor any size drawn straight horizontal lt over head lines on existing poles including binding with insulators, weight of conductor shall be measured straight horizontal distance between centre of two adjacent ht / lt poles and calculating weight of conductor or size length by adding 3% extra for sag, jointing jumpers etc complete all as specified and directed. 89 supply and fixing led street light fitting ip 66 pressure dia cast aluminium housing ( heat sink ) for effective thermal management, sturdiness excellent corrosion resistant ip operating voltage 140 270 volts, pf ( 0.95 ) , assemetric lens of leds, luminous flux>3800lm, efficacy of led>130 lm / w, of luminaires 60 watt led 5700k including fitting, lamp etc complete all as specified and directed. 90 supply and fixing in replacement lt feeder pillar box 440 volts 3 phase 4 wire 50 hz out door weather proof ip 56 ( cpri approved ) made out of 3mm thick crca sheet and angle iron frame made out of 50x50x6mm both side opening and suitable to fix cable glands locking arrangements powder coated and panel embarked in pcc block 30x30x60cm fixing in ground with suitable size of nut bolts and comprising of the following: ( a ) aluminium bus bar of capacity 200 amps 1 set of 4 ( ryb & black duly insulated ) ( b ) mccb 100 amps, 16 ka with adjustable thermal and fixed magnetic type ics 100% 01 no. ( c ) mcb tpn 63 amp, 10ka, 415v 02 nos ( d ) automatic quatrz time switch 3 phase 02 nos ( e ) digital amp meter of capacity 0 to 200 amp with selector switch=01 no ( f ) digital volt meter of capacity 0 to 500 volt 01 no. ( g ) led indicator lamp set of three. 91 supply and errecting prestressed concrete pole 9.0 mtrs long, 120x172mm at top and 102mm x 279mm at bottom class 10 complete with painting on poles all as specified and as directed by engr in charge. 92 material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick, buried directly in ground ( earth pit not less than 2.25 metres deep below ground level ) with top edge of the plate not less than 1.50 metres below normal ground level, earth plate surrounded from all sides by 15cm thick packed layers of charcoal dust and common salt filling in alternate layers alround, top & bottom and electrode connection by using galvanized iron earth strip 25x4mm connected to earth plate electrode by means of bolts, nuts check nuts and washers made of galvanized iron or steel and thimbles, gi pipe light grade 20mm bore for watering with funnel and wire mesh, gi medium grade 40mm bore protection pipe for drawing in earth lead wire, pcc chamber in pcc 1:2:4, type b 1 with angle iron 25x25x3mm frame work and pre cast rcc cover in rcc 1:2:4, type b 1, cover reinforced with 8mm dia tmt bars @100mm c / c both ways and 12mm dia ms fabricated handle, test point complete all as shown in electrical plate no 3 of mes standard schedule of rates ( part i ) including necessary excavation and earth work in any type of soil, returning filling and removal of soil to a distance not exc 50 metres and testing on completion complete all as specified and directed.notes ( a ) the unit rate shall include for gi protection pipe, gi watering pipe, wire mesh, funnel and excavation, rcc pit cover, test point, galvanised iron strip from top of earth plate upto 5.0 metres above ground level and if gi protection pipe is less than 5.0 metres, no price adjustment shall be made. ( b ) pccpit shall be provided at least 50cm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junction, elbow etc shall be deemed to be included in the unit rate. ( c ) if the testing result of earthingwork is not found satisfactory then the contractor shall do another earthing work at his own cost and nothing shall be permissible on this account. ( d ) earthing work will be carried out in presence of mes representative....

Military Engineer Services - Punjab

35301477 repair / maintenance and reactivation of old earthing system of electric installation and equipment in zone b under ge ( u ) bathinda m&l for earthing complete with galvanised steel earth plate electrode 60cm x60cm x6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of plate not less than 1.5m below ground level, connecting to the galvanised iron earth lead wire 4.0 mm dia , by means of nuts, bolts, check nuts and washer etc of galvanised iron and earth lead protected by provision of gi pipe light grade 32mm bore light grade from earthing test point or main controling switch as directed including providing funnel with 20mm bore gi pipe light grade, wire mesh, charcoal or coke andcommon salt in alternative layer of 15 cm ( compactedd thickness ) all round the earth electrode, concrete earth pit in pcc ( 1:2:4 ) type b 1 using 20mm graded stone agagregates with 50mm thick cover of rcc ( 1:1.5:3 ) ( re inforced with 8mm dia tmt bar @15 cm c / c bothways and ms bar handle made of 10mm dia bar ) including necessary earth work in excavation, returning in and removal of surplus soil to a distance not exceeding 50mtr, all as per electrical plate no 3 of mes schedule part i including earthing pit cover etc. after demolition the existing old unserviceable earthing completeall as directed. 2 m&l for earthing complete with gi earth plate electrode of size 60cm x 60cm x 6mm burieddirectly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including 25 x 4 mmgi strip upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia gi pipe connected to main control board and gi pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etcrcc pit coverof rcc ( 1:1.5:3 ) flush to earth pit 50mm thick reinforced with 8mm tmt bar 100mmc / c and pcc chamber pit with pcc ( 1:3:6 ) type c1 ( using 20mm graded aggregate ) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre ) and testingas specified and shown on plate no 3 of ssr part i 2009 after demolition the existing old unserviceable earthing completeall as directed.. 3 m&l for earthing complete with gi earth plate electrode of size 60cm x 60cm x 6mm burieddirectly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including 32 x 6 mmgi strip upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia gi pipe connected to main control board and gi pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etcrcc pit cover of rcc ( 1:1.5:3 ) flush to earth pit 50mm thick reinforced with 8mm tmt bar 100mmc / c and pcc chamber pit with pcc ( 1:3:6 ) type c1 ( using 20mm graded aggregate ) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre ) and testingas specified and shown on plate no 3 of ssr part i 2009 after demolition the existing old unserviceable earthing completeall as directed.. 4 supply, installation, testing and commissioning in replacement of maintenance free earthing ( grounding ) electrode of size 85 mm dia x 3 mtrlong with 17.2 mm cu bonded ms conductorin high purity electrically conductive granular material having ultra low resistive value of 0.001 ohm m. electrode made of conductive earth enhancing material mixed with cement in the ratio ( 3:1 ) backfill the voids surrounding the 17.2 mm cu bonded ms conductor or other metal components placed in augured bore hole of 100mm dia x 3 mtr depth, resulting to increase in the effective surface area of the earth electrode or grids to lower the resistance. earth enhancing matetial should not leach chemicals into the adjacent soil or underground water channels and should be in ph neutral range.earth enhancing material should permanently protect the encased metal components of the earthing system, copper bonding on ms rod should be minimum 250 microns.all hardware like nuts, bolts and washers should be of stainless steel. electrode should withstand fault current upto 35 ka for 1 second. electrodes top terminal be sealed permanently packed with conductive concrete and cu bonded copper strip of size 32mmx 6mmtaken out be terminated on to earth test point and equipment terminal upto 7mtr length. test certificate of nabal laboratory shall be submitted by the contractor, test link of size 50 mmx 6 mm x 200 mm, rcc pit cover test point complete, all as specified and directed by engineer in charge. make: elancretenote : ( i ) test certificate of earthing material from certified nabl laboratory shall be submitted. ( ii ) test reports should not be more than 7 year old. ( iii ) test report for fault current, rohs compliance, resistivity value from nabl certified / cpri lab ismust be submitted. 5 supply and fix in repair earth continuity conductor or main earthing lead fixed to wall on battenor recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required by using25mm x 4 mm gi strip complete all as specified anddirected. 6 supply and fix in repair earth continuity conductor or main earthing lead fixed to wall on battenor recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required by using32 mm x 6 mm gi strip complete all as specified anddirected. 7 supply and layinggi tubing, light grade, 40 mm bore complete with all fittings for cable and earth continuity strip protection laid in trenches / fixed to poles / along wall / under road / across the drain complete all as specified and as directed.make: tata / jindal / swastik / surya prakash 8 m&l for construction of earthing pit chamber after demolition of old unserviceable earthing pit chamber with pcc ( 1:3:6 ) type c1 using 20 mm graded crushed stone aggregate, pre cast rcc ( 1:1.5:3 ) typea1 using 20 mm graded crushed stone aggregate as in 50 mm thick cover slab reiforced with 4 mm dia tmt bar @ 150 mm c / c both ways with one handle of 8 mm dia tmtbar embeded in cover slab for lifting including painting the external surface of chamber and cover with two coats of synthetic enamel paints in different colours as directed and writing earth resuls and date of test carried out with white paint on black painted back ground complete all as directed. 9 supply only porcelain insulator white ceramic for gi / aluminium strip supporter , size should be adequate to accommodate strip of 32 mm with fastener complete all as directed. 10 m&l for construction of earth test point after demolition of old unserviceable earth test point including gi, / copper strip, clamps, nut bolts, washers, porcelain insulator etc complete all as directed....

Patiala Locomotive Works - Punjab

34040399 supply of set ( moto set ) of mp / cp coilsset ( moto set ) of mp / cp coils, set ( motor set ) of mp / cp coils with shoes fully potted, interconnectors and lead wires for hitachi tm stator, type hs 15250a, conforming to clws specification no. 4tms.095.032 alt 4 & 4tms.095.033 alt 4. one motor set consisting of ( 1 ) main pole coil with shoes ( south pole ) drg no. 10s 808 414 rev.d, qty 03 nos. ( 2 ) main pole coil with shoes ( north pole ) drg no.10s 808 415 rev.d, qty 03 nos. ( 3 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 416 rev.d, qty 02 nos. ( 4 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 417 rev.d, qty 01 no. ( 5 ) comm. pole coil with shoes ( north pole ) drg no.10s 808 418 rev.d, qty 02 nos. ( 6 ) comm. pole coil with shoes ( north pole ) drg no. 10s 808 419, rev.d, qty 01 no. lead wire a drg no. 3twd.095.067, qty. 1 no. lead wire drg no. 3twd.095.069, alt 1, qty. 1 no. lead wire aa drg no. 3twd.095.068, alt 1, qty. 1 no. lead wire fdrg no. 3twd.095.073, alt 1, qty. 1 no. lead wire ff drg no. 3twd.095.074, alt 2, qty. 1 no. lead wire drg no.3twd.095.071, alt 1, qty.2 nos. lead wire drg no. 3twd.095.070, alt 2, qty. 2 nos. & lead wire drg no.3twd.095.072 alt 1, qty 1 no. and connector for main pole drg no. 4twd.092.510, qty 5 nos, to spec. no. 4tms / 095 / 028 or latest & e 0028 or latest & rdso str no. rdso / 2007 / el / str / 023, rev 1 for hitachi traction motor type 15250a of electric loco. ] page 1 of 6 run date / time: 21 / 09 / 2022 10:10:39plw hq stores / plw tender document...

Patiala Locomotive Works - Punjab

34020661 supply of set of lead wireset of lead wire, set of lead wire, each set consist of 05 items for hitachi tm type hs 15250a to drg.no. 3twd.095.057, rev 7 ( 01no ) , 3twd.095.058, rev 7 ( 01no ) , 3twd.095.075 ( 02 nos ) , 3twd.095.076 ( 01 no ) , 3twd.095.077 ( 01 no ) ....

Northern Railway - Punjab

33703673 supply of lead wire negative for hs 15250 tm, specn. no. 3twd.095.058 alt.7 or latestlead wire negative for hs 15250 tm, specn. no. 3twd.095.058 alt.7 or latest,lead wire negative for hs 15250 tm, specn. no. 3twd.095.058 alt.7 or latest...

Military Engineer Services - Punjab

32469074 cwe / pat / t 75 / 2021 22 provn of med store for echs and ration shelter for mh under ge north patiala provn of med store for echs and ration shelter for mh schedule asection i (building works) 2 total amount of sch a sec i (building works) 3 schedule asection ii (excavation and earth works) 4 total amount of sch a sec ii (excavation and earth works) 5 schedule asection iii (internal electric supply) 6 total amount of sch a sec iii (internal electric supply works) 7 schedule asection vi (road and path works) 8 total amount of sch a sec iv (road and path works) 9 schedule asection v (ext elect suppy) 10 total amount of sch a sec v (ext elect works) 11 schedule asection vi(misc items of works) note :this schedule is not pre priced by mes and the pre priced rate indicated as rs 0.00 under col. 5 siginifies this fact only. 12 supply & fix1 x 20 w, 4 feet 230 voltsnecessary electric connection with twisted flexible pvc copper counductor cablefrom ceiling rose complete all as specified and directed by engineer in charge.make : cat part no lhlddcxcml8q020 of havells or equivalent in makes as per appendix b. 13 supply & fix security led light fitting20 watt luminaries new generation energy saving ,with lens made of pressure die cast alluminium alloy powder coatedhousing lm24inclsnecessary electric connection with twisted flexible pvc copper counductor cable clamp for fixingcomplete all as specified and directed by engineer in charge.make : cat part no lhexayp7pn6k020 of havells or equivalent in makes as per appendix b. 14 supply and fixmcb spn 40amp ,10ka 240volts isi marked all as specified and directed by engr in charge. 15 supply and fixmcb sp 06 32 amps ,10ka 240volts isi marked all as specified and directed by engr in charge. 16 earthingcomplete with galvanised steel plate earth electrode 60cmx60cmx6mm thick, burried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolt, nut check nuts and washer of galvanised iron or steel with protection of gi, medium grade 15mm bore upto adequate length watering pipe 25/40mm bore for protection of gi wire/strip from earth electrode to and incl the supplying and laying charcoal dustcommon salt, pcc 1:3:6 type ci (using 20mm gradedcrushed stone aggegrate) as in chamber and ms angle iron frame 40x40x3mm and rcc cover 40mm thick 1:2:4 type b1 (using 20mm gradedcrushed stone aggregate) reinforced with 8mm dia, tmt bars @75mm c/c both ways with ms handle 12mm dia, pgi funnel and wire mesh, 20 mmdia gi pipe light grade for watering all as shown in electrical plate no 3 of ssr part i of 2009 and connected to earth test point testing complete all as specified and directed 17 machine pressed rubber moulded isi marked precast cement concrete interlocking paver block any shape and size with grey cement and no pigment confirming to is 15658 2006 of 60mm thickness m 35 grade and including filling of interstices with fine sand over including 25mm thick layer of sand chusion complete all as specified. 18 s &f ceiling rose bakelite,63.5mm 3 terminals with base plate isi marked, complete allas specified and directed by engineer in charge. 19 s&fceiling fan complete with blades,down rod, electronic regulator and accessories 230v,1200mm, complete all as specified and as directed. 20 sandcushioningwith clean dry sandto cables with layer of sand 8cm before laying of cable and 15cm thick after laying of cablecomplete all as specified.note : for payment purpose punned thickness of 18cm shall be measured against spread thickness of 23cm as mentioned in para 19.75 of ssr part i. 21 mcb db double door 240 volts with 200 amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting type, drilling holes for incoming and out going cables complete suitable for 8 ways with ip43 protection complete all as specefied and as directed. 22 supply and hanging exhaust fan with sweep 350mm single phase 250v ac supply heavy duty including all fixing material and arrangements, provision of 2 way pvc connector, copper bunched flexible cable 1 sqmm twin twisted pvc insulated cable from ceiling rose / connector to fan complete all as specified and as directed. ...

Ministry Of Railways - Punjab

32049546 supply of set ( motor set ) of mp / cp coilsset ( motor set ) of mp / cp coils, set ( motor set ) of mp / cp coils with shoes fully potted, interconnectors and lead wires for hitachi tm stator, type hs 15250a, conforming to clws specification no. 4tms.095.032 alt 4 & 4tms.095.033 alt 4. one motor set consisting of ( 1 ) main pole coil with shoes ( south pole ) drg no. 10s 808 414 rev.d, qty 03 nos. ( 2 ) main pole coil with shoes ( north pole ) drg no.10s 808 415 rev.d, qty 03 nos. ( 3 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 416 rev.d, qty 02 nos. ( 4 ) comm. pole coil with shoes ( south pole ) drg no. 10s 808 417 rev.d, qty 01 no. ( 5 ) comm. pole coil with shoes ( north pole ) drg no.10s 808 418 rev.d, qty 02 nos. ( 6 ) comm. pole coil with shoes ( north pole ) drg no. 10s 808 419, rev.d, qty 01 no. lead wire a drg no. 3twd.095.067, qty. 1 no. lead wire drg no. 3twd.095.069, alt 1, qty. 1 no. lead wire aa drg no. 3twd.095.068, alt 1, qty. 1 no. lead wire fdrg no. 3twd.095.073, alt 1, qty. 1 no. lead wire ff drg no. 3twd.095.074, alt 2, qty. 1 no. lead wire drg no.3twd.095.071, alt 1, qty.2 nos. lead wire drg no. 3twd.095.070, alt 2, qty. 2 nos. & lead wire drg no.3twd.095.072 alt 1, qty 1 no. and connector for main pole drg no. 4twd.092.510, qty 5 nos, to spec. no. 4tms / 095 / 028 or latest & e 0028 or latest & rdso str no. rdso / 2007 / el / str / 023, rev 1 for hitachi traction motor type 15250a of electric loco. ] page 1 of 6 run date / time: 29 / 04 / 2022 12:07:47plw hq stores / plw tender document...

Ministry Of Railways - Punjab

32033776 supply of set of lead wires for hitachiset of lead wires for hitachi, set of lead wires for hitachi tm stator of 15250a tm type ( one set consisting of the following ) ( 1 ) lead wire a, to drg.no. 3twd.095.067 qty.01 no. ( 2 ) lead wlre, drg no.3twd.095.069 alt 1.qty.01 no., ( 3 ) lead wire aa, drg no. 3twd.095.068 alt 1. qty. 01 no. ( 4 ) lead wire f, drg no.3twd.095.073, alt 1.qty.01no., ( 5 ) lead wire ff, drg no. 3twd.095.074, alt 2. qty. 01 no. ( 6 ) lead wire, drg no. 3twd.095.071 alt 1 qty. 02 nos., ( 7 ) lead wire, drg no. 3twd.095.070 alt 2. qty. 02 nos. , ( 8 ) lead wire drg no. 3twd095.072 alt 1 qty.o1 no. ( 9 ) connector for main pole, drg no. 4twd 092 510 qty.05 nos. confirming to specification no. 4 tms / 095 / 028 or latest & e 0028 or latest, for hitachi tm type hs 15250a for elect. loco....

Diesel Loco Modernization Works - Punjab

30114888 supply of set of lead wireset of lead wire,set of lead wire, each set consist of 05 items for hitachi tm type hs 15250ato drg.no. 3twd.095.057,rev 7(01no), 3twd.095.058,rev 7(01no), 3twd.095.075 (02 nos),3twd.095.076 (01 no), 3twd.095.077 (01 no)...

Diesel Loco Modernization Works - Punjab

29926350 supply of set of lead wires for hitachiset of lead wires for hitachi,set of lead wires for hitachi tm stator of 15250a tm type (one setconsisting of the following) (1)lead wire a, to drg.no. 3twd.095.067 qty.01 no. (2)leadwlre,drg no.3twd.095.069 alt 1.qty.01 no.,(3) lead wire aa, drg no. 3twd.095.068 alt 1. qty. 01 no.(4) lead wire f, drg no.3twd.095.073,alt 1.qty.01no., (5) lead wire ff, drg no. 3twd.095.074, alt 2. qty. 01 no. (6) lead wire, drg no. 3twd.095.071 alt 1 qty. 02 nos., (7) lead wire, drg no.3twd.095.070 alt 2. qty. 02 nos. , (8) lead wire drg no. 3twd095.072 alt 1 qty.o1 no. (9)connector for main pole, drg no. 4twd 092 510 qty.05 nos. confirming to specification no. 4 tms/095/028 or latest & e 0028 or latest, for hitachi tm type hs 15250a for elect. loco. => limited...

Diesel Loco Modernization Works - Punjab

29904796 supply of set (motor set) of mp/cp coilsset (motor set) of mp/cp coils,set (motor set) of mp/cp coils with shoes fully potted, interconnectors and lead wires for hitachitm stator, type hs 15250a, conforming to clws specification no. 4tms.095.032 alt 4 & 4tms.095.033alt 4. one motor set consisting of (1) main pole coil with shoes (south pole) drg no. 10s 808 414 rev.d,qty 03 nos. (2) main pole coil with shoes (north pole) drg no.10s 808 415 rev.d, qty 03 nos. (3) comm.pole coil with shoes (south pole)drg no. 10s 808 416 rev.d, qty 02 nos. (4) comm. pole coil with shoes(south pole) drg no. 10s 808 417 rev.d, qty 01 no. (5) comm. pole coil with shoes (north pole) drg no.10s 808 418 rev.d, qty 02 nos. (6) comm. pole coil with shoes (north pole) drg no. 10s 808 419, rev.d, qty 01no. lead wire a drg no. 3twd.095.067, qty. 1 no. lead wire drg no. 3twd.095.069, alt 1, qty. 1 no. leadwire aa drg no. 3twd.095.068, alt 1, qty. 1 no. lead wire fdrg no. 3twd.095.073, alt 1, qty. 1 no. leadwire ff drg no. 3twd.095.074, alt 2, qty. 1 no. lead wire drg no.3twd.095.071, alt 1, qty.2 nos. leadwire drg no. 3twd.095.070, alt 2, qty. 2 nos. & lead wire drg no.3twd.095.072 alt 1, qty 1 no. andconnector for main pole drg no. 4twd.092.510, qty 5 nos, to spec. no. 4tms/095/028 or latest & e 0028 orlatest & rdso str no. rdso/2007/el/str/023, rev 1 for hitachi traction motor type 15250a of electricloco.]...

Diesel Loco Modernization Works - Punjab

28459886 supply of set of lead wire.set of lead wire., set of lead wire, each set consist of 05 items for hitachi tm type hs 15250a to drg.no. 3twd.095.057 ( 01no ) , 3twd.095.058 ( 01no ) , 3twd.095.075 ( 02 nos ) , 3twd.095.076 ( 01 no ) , 3twd.095.077 ( 01 no ) ....

Baba Farid University Of Helath Sciences - Punjab

27609588 tender for procurement of surgical instruments in urology dept at ggsmch fdk 2 adson forceps toothed 5 titanium 3 scissor curved round tip tungsten 7 4 needle holder tungsten carbide 5 5 bipolar cautery small 5 forceps 6 adson forceps plain 5 titanium 7 scissor curved round tip tungsten 5 8 needle holder tungsten carbide 8 9 bipolar cautery lead wire 10 adson forceps toothed 5 ½ fine 11 needle holder fine 5 12 mosquito forceps size curved 5 13 mixter right angle forceps rt angle 6 14 mixter right angle forceps rt angle 8 15 suture cutting scissor straight 16 metzenbum scissor 5 17 metzenbum scissor 8 18 knapp scissor curved tc 5 round 19 knapp scissor curved 4.5 round 20 metzenbaum scissors 6 curved 20cm 21 halsted mosquito haemostatic forceps 5 curved 13 cm 22 ryder vascular needle holder 8 20 cm 23 microscissor curved 120 125 mm 24 bulldog clamps straight, microvascular anastamosis 25 bulldog clamps curved, microvascular anastamosis...

Diesel Loco Modernization Works - Punjab

27087571 supply of , set (motor set) of mp/cp coils with shoes fully potted, interconnectors and lead wires for hitachi tm stator, type hs 15250a, conforming to clws specification no. 4tms.095.032 alt 4 & 4tms.095.033 alt 4. one motor set consisting of (1) main pole coil with shoes (south pole) drg no. 10s 808 414 rev.d, qty 03 nos. (2) main pole coil with shoes (north pole) drg no. 10s 808 415 rev.d, qty 03 nos. (3) comm. pole coil with shoes (south pole)drg no. 10s 808 416 rev.d, qty 02 nos. , (4) comm. pole coil with shoes (south pole) drg no. 10s 808 417 rev.d, qty 01 no. (5) comm. pole coil with shoes (north pole) drg no.10s 808 418 rev.d, qty 02 nos. (6) comm. pole coil with shoes (north pole) drg no. 10s 808 419, rev.d, qty 01 no. lead wire a drg no. 3twd.095.067, qty. 1 no. lead wire drg no. 3twd.095.069, alt 1, qty. 1 no. lead wire aa drg no. 3twd.095.068, alt 1, qty. 1 no. lead wire fdrg no. 3twd.095.073, alt 1, qty. 1 no. lead wire ff drg no. 3twd.095.074, alt 2, qty. 1 no. & lead wire drg no.3twd.095.071, alt 1, qty.2 nos. lead wire drg no. 3twd.095.070, alt 2, qty. 2 nos. & lead wire drg no.3twd.095.072 alt 1, qty 1 no. and connector for main pole drg no. 4twd 092 510, qty 5 nos, to spec. no. 4tms/095/028 or latest & e 0028 or latest & rdso str no. rdso/2007/el/str/023, rev 1 for hitachi traction motor type 15250a of electric loco....

Diesel Loco Modernization Works - Punjab

26091182 supply of , set of lead wires for hitachi tm stator of 15250a tm type (one set consisting of the following) (1)lead wire a, to drg.no. 3twd.095.067 qty.01 no. (2)lead wlre,drg no.3twd.095.069 alt 1.qty.01 no.,(3) lead wire aa, drg no. 3twd.095.068 alt 1. qty. 01 no. (4) lead wire f, drg no.3twd.095.073,alt 1.qty.01no., (5) lead wire ff, drg no. 3twd.095.074, alt 2. qty. 01 no. (6) lead wire, drg no. 3twd.095.071 alt 1 qty. 02 nos., (7) lead wire, drg no. 3twd.095.070 alt 2. qty. 02 nos. , (8) lead wire drg no. 3twd 095.072 alt 1 qty.o1 no. (9) connector for main pole, drg no. 4twd 092 510 qty.05 nos. confirming to specification no. 4 tms /095/028 or latest & e 0028 or latest, for hitachi tm type hs 15250a for elect. loco....

Diesel Loco Modernization Works - Punjab

26091158 supply of , set of lead wire, each set consists of 05 items for hitachi tm type hs 15250a to drg.no. 3twd.095.057 alt 7,qty 01 no: 3twd.095.058 alt 7,qty 01no:3twd.095.075,qty 02nos:3twd.095.076,qty 01no: 3twd.095.077,qty 01 no....

Military Engineer Services - Punjab

25614203 certain sanctioned work for age b / r and age e / m at nams 2 surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed. 3 m&l for rough excavation not exceeding 1.5 m deep and getting out in soft / loose soil complete all as spd and directed. 4 excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m depth for foundation, etc., and getting out in soft / loose soil complete all as specified and directed. 5 excavating post holes or similar holes, each not exceeding 0.5 cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface 6 m&l for returning, filling in, including spreading, levelling, watering and well ramming in layers under floors or trenches complete all as specified and directed.complete all as spd 7 m&l for removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. 8 m&l hardcore of gauge not exc 63mm broken stone or boulders but not exc 100mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rolled / rammed to a true surface for levelling the surfaces 9 m & l reinforced cement concrete type a1 1:1.5:3 ( using 20 mm graded stone aggregate ) in foundations including rafts, footings and mass concrete complete all as specified and directed. 10 m & l for pcc 1:2:4 type b 2 ( using 12.5 mm graded stone aggregate ) as in flooring incl finishing the cement concrete surface even and smooth with using extra cement , rubbish off the primises complete all as specified and as directed by engg in charge. 11 m&l for cement concrete , type c1 1:3:6 ( using 40 mm graded aggregate ) as in foundation filling and mass concrete complete all as specified and directed. 12 m&l for hard core of ( broken bricks ) of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and rolled / rammed to a true surface complete all as specified and directed. 13 m & l for plain cement concrete type d2 1:4:8 ( using 40 mm graded granite stone aggregate ) in foundations, filling and mass concrete complete all as specified and directed. 14 m&l pcc 1:2:4 type b1 ( using 20 mm graded stonr aggregete ) as in coping, benching etc complete all as specified and directed. 15 supply only integral water proofing compound. 16 m&l for brick work with subclass ‘b’ bricks, straight or curved on plan exc 6m mean radius, built in cm 1:6 complete all as specified and directed. 17 m&l for brick work with locally available subclass ‘b’ old size bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:6 complete all as specified and directed by engg in charge. 18 material and labour for 15mm thick cement plaster in cm 1:4 on fair faces of brick work and finishing the surface even and smooth ( without using extra cement ) etc. complete all as specified and directed. 19 m&l for newly plastered wall surfaces and applying two coats of exterior weather proof emulsion paint over one coat alkali resistant primer complete all as specified and directed. 20 m & l for 15 17mm thick kota stone slab as in treads, risers and flooring etc. laid over 15 mm thick screed bed or bedding layers in cm 1:6 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and mirror polished polishing types complete all as specified and directed. 21 s & f mild steel rag or lewis bolts of 20 mm dia, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised and exc. 30 mm long complete all as specified and directed. 22 s & f steel work in tubular trusses and tubular posts including special shaped washers, etc., complete using but welded tubes confirming to is 1161 1979 graded st 240 complete all as specified and directed. 23 s & f rolled mild steel plates ( plain or chequered ) channels, square cut or notched, forming holes, without any attachment confirming to fe 410 w ( gde e 250 ) quality a, complete all as specified and directed. 24 m&l two coats of synthetic enamel paint over a coat of red oxide primer over steel surfaces including preparation of new surface complete all as specified and directed. 25 s&f for pre painted galvaume aluminum zinc coating gi based manglore / trapezoidal / semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding, fixed with self tapping screws as specifiedcomplete all as specified and directed. nnote design / pattern / colour of roofing sheet sheet to decided and approved by eic / ge. 26 m & l for 0.63mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings ( length and girth as fixed ) with grade of zinc coating 275 complete all as specified and direcyed. 27 use and waste form work to sides of concrfete footings and similar works for fair finished surface all as specifed and directed. 28 use and waste of form work to edges of concrfete flats, slabs etc incl fair finished surface all as specifed and directed. 29 use and waste of form to staircases with sloping or stepped soffits including risers and stringers ( excluding landing ) complete as specified and directed. 30 m & l for plain cement concrete type b1 1:2:4 ( using 20 mm graded granite stone aggregate ) in foundations, filling and mass concrete. 31 m & l for formwork to sides and soffits of floor or roof beam, lintel beams flat surface etc incl supports, overhangs etc complete all as specified. 32 m&l for box type steel window 1.25 mm thick made of erw tube p section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter ( two gauged shutters and two glazed shutter ) of erw tube p section size 50 x 20 mm and 1mm thick one / two nos openable leaf consisting of two nos sash bar of t section 20x3mm welded to frame with one no vertical mullion of erw box type t section of size 60 x 25 mm and 1.25 mm thick and fi 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like handle, tower bolt, stopper, cleat, pintal hinges, hold fast etc. ( i ) hold fast, 150mm long of 120mm x 3 mm made to shape 04 nos per window. ( ii ) handle of z sec 20mm x 25mm, 100 mm long 1 no per leaf ( iii ) ms tower bolt 150mm long 2 no per leaf ( iv ) z sec 20mm x 25 mm, 100 mm long stopper 1 no per leaf ( v ) cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge 1 no per leaf. ( vi ) ms pintal hinges of size 75mm x 12mm 2 nos per leaf . ( vii ) 10 mm square guard bar, 10 cm centre to centre. ( viii ) 25x4 mm flat iron all around for joint of both frame. ( ix ) stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples. ( x ) two coat of synthetic enamel paint to ms window and guard bar complete all as specified and directed. 33 s & f mild steel box type ventilator fixed type with glazing bar with mesh & glass as per drg no. cejz / td 06 / 07 dt 07.06.07 complete all as specified. 34 s&f tmt bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips and complete all as specified. 35 all as per item 34 here in before but 6 to 8 mm dia and including in stirrups, spacers and binders and complete all as specified. 36 supply and fixing mild steel roof truss, purlins, rail and fastenings and heavy bracket framing ( beam, tee, angle, channel, flat section ) including distrance pieces, welding work, cleats, nutand bolt etc ( fe 410w ) complete all as specified and directed. 37 s&f 1.25mm thick steel rolling shutter with ball bearing and gear operated type with bevel gear box and crank handle as specified including to hood cover , an choring rod, stopper, holdfast, pulling hook, sliding lock, handle hasp and staple and one coat of primer erected in position as indicated complete all as specified and directed by engg in charge. 38 s & f safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by engg in charge. 39 s & f ball bearing for rolling shutters complete all as specified and directed. 40 supply and fixing pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, in ridges, hips, vally gutter, drip complete all as specified and directed by engineer in charge. 41 s & f mild steel plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, without ant attachment ( fe 410 w ) gde e 250 quality a complete all as specified and as directed by engg in charge. 42 m&l for providing 75 mm thick cement concrete ( 1:3:6 ) type ci using 40mm graded stone aggregate as in plinth protection / pathway surfaces even and smooth without using extra cement. 43 m&l for pre cast rcc normal mix ( 1:2:4 ) type b1 ( using 20 mm graded stone aggregate ) . as in slabs supported on walls, beams and coloums in floors and roofs, landing balconies chaza, etc all as specified and directed . 44 m&l for 15 mm thick rendering on external surface with cement mortar ( 1:4 ) on fair face of brick or concrete surface finished even and fair using wpc @3% by weight of cement complete all specified and directed ( wpc shall be mesuredand paid saparately ) . 45 m&l for 15 mm thick rendering on internal surface with cement mortar ( 1:6 ) on fair face of brick or concrete surface finished even and fair complete all specified and directed . 46 m&l preparation of newly plastered surfaces and applying two coats of cement base paint of shade as approve over a coat of cement primer on wall complete all as specified and directed. 47 m & l for preparation of new plastered surface of walls and applying three coats of white wash as directed. 48 s&f in 3mm glass thick ordinary quality and glazing with oil putty or wooden beading and securing pins n.exc 0.50 sqm each panes complete all as specified and directed. 49 m & for reinforced cement concrete type b0 1:2:4 ( using 12.5 mm graded granite stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 159, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed 50 supply, lowering, commissioning & testing of submersible pump capacity 1350 lpm at head of 80 mtr with out let size 100 mm dia bore including electric motor driven 415 v 50 hz complete all as specified and directed. 51 supply, lowering, commissioning & testing of submersible pump capacity 1650 lpm at head of 80 mtr with out let size 125 mm dia bore including electric motor driven 415 v 50 hz complete all as specified and directed. 52 supply, lowering and fixing ms heavy duty flanged pipe 5.4mm thick 100 mm bore ( length not less thatn 3 mtr each ) ms flanged not less than 15mm thick on both side, with drilled holes and welded to ms pipe, including material and labour for jointing, fixing with nuts, bolt, rubber packing complete all as specified and directed. 53 supply, lowering and fixing ms heavy duty flanged pipe 5.4mm thick 150 mm bore or nearest higher size bore ( length not less thatn 3 mtr each ) ms flanged not less than 15mm thick on both side, with drilled holes and welded to ms pipe, including material and labour for jointing, fixing with nuts, bolt, rubber packing complete all as specified and directed. 54 s&f submersible cable 25 sqmm, 3 core pvc copper cable, 1100 volts gradde conforming is 694, complete with all accessories all as specified and as directed. 55 supply, laying & fixing double wall corrugated ( dwc ) pipes for passing the cable along wall / under road, path etc made of high density polythyline ( hdpe ) with all accessories i.e. all type of joints, sockets, elbows, bends and end caps etc.. all as specified and directed by engr in charge.of size 40 mm outer dia and 38 mm inner dia of pipe 56 supply, install, testing & commissioning factory made indoor type dust and vermin proof motor starter panel cubical double door hinged type compartmentalized of suitable size fabricated of crca sheet 2.0 mm thick machine pressed and angle iron frame powder coated inside and outside, including 4 pole 415 volt, ac, 50 hz, copper busbar of capacity 300 amps mounted on porcelain insulators and enclosed in bus bar chamber and connection from incoming and outgoing electric cable with suitable size thimbs.lugs with openable shutters and fixed on angle iron frame made out from 40x40x6mm angle iron andgrounted in pcc 1:2:4, type b 1 ( using 20mm graded stone agregate ) , including accomodating & comprising of the following including taking out old unserviceable motor starter panel all as specified and directed : ( a ) mccb 250 amps capacity with adjustable thermal release 4 pole of 25 ka rupturing capacity 01 no ( incomming ) . n ( b ) mccb 160 amps 25ka , three pole 415 volt 01 no. ( outgoing ) n ( c ) mcb 32 amps 10 ka tpn 415 volt 02 no. ( out going ) ( d ) ( i ) digital volt meter showing 0 500 volts complete with duly nprewired with copper cable of suitable size 01 no. ( ii ) digital ampere meter showing 0 100 amps with 01 no. n ( iii ) indication lamp ryb led type with protection fuses 01 set ( iv ) soft starter in steel enclosure comprising of the following appliances of make l&t csxi model cat part csxi 037 41 or equivalent in siemens, havells etc: na ) in built bypass contractor nb ) soft start / start stop / adjustable current limit nc ) essential motor protection against ( i ) overload ( ii ) single phasing ( iii ) instantaneous overcurrent ( iv ) phase sequence reversal ( v ) abnormality in supply ( vi ) unbalanced current nd ) thermistor protection through ptc ne ) excess start time setting 57 m & l for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below level connected an including gi strip 32 x 6 mm as earth lead upto 7.5 mtr long by means of bolts, nuts, check nuts and washers etc with gi protection pipe of 40 mm bore medium grade and connected to earthing test point all as shawn in electrical plate no 3 of sr part i and as specified or indicated including excavation & earth work in any type of soilpcc ( 1:2:4 ) type b1 ( reinforced with welded steel wire fabric ( xpm ) of weight not less than 4 kg ( sqm ) with frame funnel with 20 mm bore gi pipe medium grade watering pipe, wire mesh and lugs test point etc and testing on completion. nnot : ( a ) the unit rates includes 32 x 6mm gi pipe strip and 40mm gi protection pipe top of earth plate upto test point ) 58 m&l for point wiring with 1.5 sqmm ( nominal area ) 1100 volt pvc insulated , frls unsheathed and multi stranded copper conductor cable in and including new pvc concealed conduit not less than 20mm dia 1.5mm thick for one light / fan point or bell point controlled by one switch ( including cutting chases and making good the disturbed surfaces ) and fixing new 3mm thick hylem sheet top cover, sheet screws and 1.6mm thick gi sunken boxes included 1.5 sqmm stranded copper conductor with green pvc insulation earth contunity conductor connected to common earth dolly etc . complete all as specified and directed. note : the cost of sunken boxes and bakellite sheet is included in the quoted rate ) 59 all as per item 58 here in before but for one three pin socket outlet 5 amps independent board complete 60 all as per item 58 here in before but for one three pin 5 amps socket outlet on the same board with other switches 61 all a per item no 58 here in above but with 2.5 sq mm size cable multi stranded frls copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continuous earth wire of pvc insulated 1.5 sq mm copper solid conductor connecting to common earth dolly complete. 62 supply and fixing switch piano type 6 amps one way 230 volts ac complete all as specified and as directed 63 supply and fixing socket outlet 5 pin, 6 amps flush type 230 volts ac complete all as specified and as directed 64 supply and fixing switch piano 16 amps type one way 230 volts ac complete all as specified and as directed 65 supply and fixing socket outlet 6 pin 6 / 16 amps multi purpose flush type 230 volts ac complete all as specified and as directed 66 supply and fixing ceiling rose 65x50 mm two to three terminals complete all as specified. 67 material and labour of lamp holder insulated body with back plate angle type for batten fitting fixed on bakelite sheet 100mmx100mm with 10 watt led bulb 230v ac cool day light 6500k having maximum height 1020mm heavy duty complete all as specified. 68 m&l for two single core sub main wiring 6 sqmm multi strand pvc insulated frls copper conductor cable including pvc insulated copper conductor cable of size 6 sqmm as cotinuous earth wire connecting to common earth including pvc conduit , connections of cable with mcbs or bus bars complete all as specified and directed 69 m & l for sheet steel enclouser distribution boards, double door factory made 3 phase 415 volts 4 way with 200 amps rating copper bus bar and pvc insulated copper jumpers of suitable size from the mccb to the out going circuits one incoming mccb and 12 outgoing mcbs circuits comprising of 3 phase 4 wire of suitable rating complete all as spcd and directed with the following accessories : ( for out going mcb measured and paid for separately ) ( a ) mccb 100 amps, 16 ka, tp, 415 volts, 50 hz = 01 no. 70 supply and fixing mcb single pole 6 to 32 amps all as specified and directed 71 supplying and fixing mcb dp 40 amps 240v, 10 ka, complete all as specified and as directed 72 m&l for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by gi pipe 15 mm bore ( light grade ) and watering pipe 20 mm bore gi pipe ( light grade ) and chamber of pcc 1:4:8 type d2 using 40 mm graded stone aggregate and coping shall be in pcc 1:3:6 type c1 using 20mm graded stone agg. 50 mm thick cover of rcc 1:2:4 type b1 using 20 mm graded stone agg. reinforced with 8 mm dia ms tor bar @ 80 mm c / c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 5 of ssr pt 1, 1991 with charcoal dust and salt complete and earth lead connected to earthing test point ( up to main switche, dbs ) complete all as specified & testing on completion. 73 supply & fix of led street light luminaire 25 watt 6000k with .high power led cool white, cri 75, + / 5% supply voltage 220 / 240 / 50 hz, light engine driver base.pole adapter, powder coated pressure die cast aluminium with heat resistant toughened glass with lens.complete all as specified and as directed. 74 supply & laying xlpe insulated armoured heavy duty electric cable with aluninium conductor 1100 volt grade cross section area 4 core 25 sqmm complete all as specified and as directed. 75 supply, laying & fixing double wall corrugated ( dwc ) pipes made of high density polythyline ( hdpe ) with all accessories i.e. all type of joints, sockets, elbows, bends and end caps etc.. all as specified and directed by engr in charge.of size50 mm outer dia and 38 mm inner dia complete all as specified and directed. 76 supply and fixing of led t 8 tube light fitting with single side connection led tube rod 18 / 20w 4 feet 1 x 18 / 20 watt ms crca box type including rotary type bipin holder and connection with pvc insulalted twin core 23 / 0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed. 77 supply and laying or fixing 1100 volts grade heavy duty cable with pvc insulated aluminium standard conductor served with an inner sheathing of pvc tape and over all pvc sheathed in service connections one twin core 6 sqmm cable standard conductor cable flat or circular all as specified and directed by engineer in charge. 78 s &f sheet metal enlosure for dbs where mcbs to be used double door factory made flush fixed complete with 100 amps rated bus bar 240 volts single phase 8 ways complete all as specified. 79 s &f led bulk head light fittings 10watt white including led strip as per ip65 in enginnering plastic housing withclear prismatic diffuser and making necessary connections complete all as specified 80 s & f bracket made out of gi pipe 40mm medium grade 1.2 mtr long made to shape with fixing clamps of ms flat 40x6mm nuts bolts etc for street light all as specified vand direceted. 81 supply & fixing flood light luminaire 120 watt with high power smd led cool white, supply voltage 220 / 240 / 50 hz, light engine driver base pole adapter, pressure die cast, polycarbonate, powdre coated in ip 66 incliding protection over temperature should be from the same manufacturer product complete all as specified and as directed, 82 supply and fixing ceiling fan 1200mm sweep copper winding with electronic regulator, low power consumption, high speed aluminium body with blade, double ball bearing of bee star rated including acessories connector, canopy, hanging rod and clamps , including electric connection with pvc flexible twin core copper wire from ceiling rose to ceiling fan complete all as specified and directed....

Diesel Loco Modernization Works - Punjab

25442908 supply of , set (motor set) of mp/cp coils with shoes fully potted, interconnectors and lead wires for hitachi tm stator, type hs 15250a, conforming to clws specification no. 4tms.095.032 alt 4 & 4tms.095.033 alt 4. one motor set consisting of (1) main pole coil with shoes (south pole) drg no. 10s 808 414 rev.d, qty 03 nos. (2) main pole coil with shoes (north pole) drg no. 10s 808 415 rev.d, qty 03 nos (3) comm. pole coil with shoes (south pole) drg no. 10s 808 416 rev.d, qty 02 nos. , (4) comm. pole coil with shoes (south pole) drg no. 10s 808 417 rev.d, qty 01 no (5) comm. pole coil with shoes (north pole) drg no.10s 808 418 rev.d, qty 02 nos (6) comm. pole coil with shoes (north pole) drg no. 10s 808 419, rev.d, qty 01 no. lead wire a drg no. 3twd.095.067, qty. 1 no. lead wire drg no. 3twd.095.069, alt 1, qty. 1 no lead wire aa drg no. 3twd.095.068, alt 1, qty. 1 no. lead wire f drg no. 3twd.095.073, alt 1, qty. 1 no lead wire ff drg no. 3twd.095.074, alt 2, qty. 1 no. & lead wire drg no. 3twd.095.071, alt 1, qty.2 nos lead wire drg no. 3twd.095.070, alt 2, qty. 2 nos & lead wire drg no. 3twd.095.072 alt 1, qty 1 no. and connector for main pole drg no. 4twd 092 510, qty 5 nos, to spec. no. 4 tms/095/028 or latest & e 0028 or latest & rdso str no. rdso/2007/el/str/023, rev 1 for hitachi traction motor type 15250a for electric loco....

Baba Farid University Of Helath Sciences - Punjab

22812195 procurement of surgical instruments in the department of plastic surgery at ggs medical college & hospital, faridkot. 1. skin hook fine 6 2. skin hook fine 8 3. flap hook 10 4. adson forceps toothed 5 titanium 5. scissor curved round tip tungsten 7 6. needle holder tungsten carbide 5 7. kilner retractor double ended 6 8. currete fine 5 mm 9. bp handle size no.4 10. steel bowl 6 11. bone nibbler small square tip 12. bipolar cautery small 5 forceps 13. wooden meshing board 6x4x 1 ( tall) 14. electronic tourniquete double 15. suction tip 20 cm tip 5 mm 16. bone rounger curved 8 17. adson forceps plain 5 titanium 18. scissor curved round tip tungsten 5 19. needle holder tungsten carbide 8 20. currete fine 3 mm 21. bp handle size no. 3 22. kidney bowl 10 23. bone nibbler medium square tip 24. bipolar cautery lead wire 25. adson forceps toothed 5 ½ fine 26. knapp scissor curved 4.5 round 27. needle holder fine 5 28. bone nibble long square tip 29. mosquito forceps size curved 5 30. knapp scissor curved tc 5 round 31. mixter right angle forceps rt angle 6 32. mixter right angle forceps rt angle 8 33. katori small size 34. tray 10x 08 35. medium clamp 36. suture cutting scissor straight 37. metzbum scissor 5 38. metzbum scissor 8 39. k wire removal pliers...

Baba Farid University Of Helath Sciences - Punjab

22736554 tender for procurement of surgical instruments in deptt of plastic surgery at ggsmch faridkot 2 skin hook fine 6 3 skin hook fine 8 4 flap hook 10 5 adson forceps toothed 5 titanium 6 scissor curved round tip tungsten 7 7 needle holder tungsten carbide 5 8 kilner retractor double ended 6 9 currete fine 5 mm 10 bp handle size no.4 11 steel bowl 6 12 bone nibbler small square tip 13 bipolar cautery small 5 forceps 14 wooden meshing board 6x4x 1 ( tall ) 15 electronic tourniquete double 16 suction tip 20 cm tip 5 mm 17 bone rounger curved 8 18 adson forceps plain 5 titanium 19 scissor curved round tip tungsten 5 20 needle holder tungsten carbide 8 21 currete fine 3 mm 22 bp handle size no. 3 23 kidney bowl 10 24 bone nibbler medium square tip 25 bipolar cautery lead wire 26 adson forceps toothed 5 ½ fine 27 knapp scissor curved 4.5 round 28 needle holder fine 5 29 bone nibble long square tip 30 mosquito forceps size curved 5 31 knapp scissor curved tc 5 round 32 mixter right angle forceps rt angle 6 33 mixter right angle forceps rt angle 8 34 katori small size 35 tray 10x 08 36 medium clamp 37 suture cutting scissor straight 38 metzbum scissor 5 39 metzbum scissor 8 40 k wire removal pliers...

Military Engineer Services - Punjab

22550792 tender for job order : ( a ) supply , install , commissioning and testing of electrically driven centrifugal pump set , 10 hp , 415v , 50hz 1440 rpm , 8 . 5 lps , 50 mtr head with connected accessories including suitable ms channels as per manufacturers specification all as specified and as directed by engr in charge . make kirloskar model no . kdt 1050+ or equivalent model of ksb , crompton , mather & platt . , ( b ) supply , install , commissioning and testing of electrically driven centrifugal pump set , 7 . 5 hp , 415v , 50hz , 1440 rpm , 4 . 6 lps , 58 mtr head with connected accessories including suitable ms channels as per manufacturers specification all as specified and as directed by engr in charge . make kirloskar model no . kdt 864+ or equivalent model of ksb , crompton , mather & platt . , ( c ) supplying and installing commissioning of cubical lt panel made out of angle iron 50mmx50mmx6mm on all side welded to 2 . 0 mm thick crca steel sheet with openable shutters on both sides ( front and rear ) having locking arrangement totally enclosed weather proof , indoor type , powder coated suitable for 440 volts , 3 phase , 4 wire , 50 hz , aluminium bus bar including connecting all out going mccb / mcb with suitable size of aluminum bus bar of capacity 100 amp ac supply electrically connected as per norms with stranded copper cable and fixing complete all as directed by engr in charge , and fitted with following ( make : dv electromatic pvt ltd ) : ( i ) 4 pole mccb upto 63 amp , 50 hz , 415 v with rupturing capacity 25 ka 01 no ( 01 no for incoming ) make : scheneider / c&s / siemens ( ii ) 3 pole mccb 25 amp , 50 hz , 415 v with rupturing capacity 16 ka 02 nos ( outgoing ) make : scheneider / c&s / siemens . ( iii ) factory made fully automatic star delta starter including suitable size of contactor , timer & relays , spp , ameter , volt meter cts , push buttons , led idicator lamps etc . for 02 nos of motor of 10 hp capacity . make : scheneider / c&s / siemens / l&t notes : ( i ) the panel shall be front operated with cable entry from the bottom with cable glands . the fault with standing capacity shall be 25 ka . earth bus shall be part of the main feeder pillar . ( ii ) fabrication of panel to be done by cpri approved manufacturer . , ( d ) all as per item no ( d ) above but fitted with the following ( make : dv electromatic pvt ltd ) : ( i ) 4 pole mccb upto 63 amp , 50 hz , 415 v with rupturing capacity 25 ka 01 no ( 01 no for incoming ) make : scheneider / c&s / siemens ( ii ) 3 pole mccb 25 amp , 50 hz , 415 v with rupturing capacity 16 ka 02 nos ( outgoing ) make : scheneider / c&s / siemens ( iii ) factory made fully automatic star delta starter including suitable size of contactor , timer & relays , spp , ameter , volt meter cts , push buttons , led idicator lamps etc . for 02 nos of motor of 7 . 5 hp capacity . make : scheneider / c&s / siemens / l&t notes : ( i ) the panel shall be front operated with cable entry from the bottom with cable glands . the fault with standing capacity shall be 25 ka . earth bus shall be part of the main feeder pillar . ( ii ) fabrication of panel to be done by cpri approved manufacturer . , ( e ) supply and fixing submersible cable of size 6 sqmm 3 core , 440 volts , incl making connection with motor , flat with stranded copper conductor flexible complete all as specified . make : finolex / kei / polycab / havells / kalinga , ( f ) construction of foundation for pumping set of size 1 . 5 m x 1 . 5 m x 0 . 5 m pcc 1:2:4 type b 1 ( using 20 mm graded crushed stone aggregate ) including 06 nos foundation bolt of suitable size along with nuts washers etc . grouted in pcc complete all as specified & directed by engr in charge . , ( g ) s & f cross arms , bracings , flanges , supports , clamps and back plates fabricated from structural steel sections including nuts , bolts , washers , welding , bending cold or hot , drilling holes for bolts , in any shape or size as directed and inclusive of one primer coat , one under coat and one finishing coat of paint , ( h ) supply and laying mild steel pipes heavy grade including all fittings cutting and made to shape including welding & jointing with ms flanges , gaskets , nuts & bolts etc . for making of water header ( as per drawing attached at appx b & c ) of following size , all as specified & directed . make : jindal / tata / bst / praksh tubes / oswal , ( i ) 100mm dia , ( ii ) 80mm dia , ( iii ) 50 mm dia , ( j ) supply & fixing gun metal globe or gate valves or butterfly valves , isi marked with iron wheel head , screwed both ends for the following bore complete all as specified and directed of following sizes : make : kirloskar / nvr / leader / l&t / zoloto , ( i ) 80 mm , ( ii ) 50 mm , ( k ) pressure gauges 0 200 psi ( 01 nos for each pump ) make : h guru / ki / fiebig , ( l ) supply and fixing foot valve for size 80mm dia pipe isi marked with flanged ends drilled with iron wheels head shuts and open direction cast on it including suitable size of rubber insulation packing rings , jointing material nuts , bolts & washers etc . complete all as specified & diredted . make : kirloskar / nvr / bir , ( m ) supply and fixing 80mm bore dia cast iron non return valve flanged class pn 1 . 6 conforming to is : 5312 part i with suitable size of rubber gasket , nuts & bolts washers complete all as specified & directed of following sizes : make : kirloskar / nvr / bir , ( i ) 80mm , ( ii ) 50mm , ( n ) m&l for earthing complete with galvanised steel earth plate electrode 600mmx600mm thickness not less than 6mm thick buried directly in ground ( earth pit not less than 2 . 25 mtr deep below normal ground level ) with top edge of earth plate not less than 1 . 5m below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts , nuts , check nuts and washers of galvanised iron / steel all as shown in electric plate no 3 connected to earth test point / mcb dbs all as specified and indicated complete with funnel , charcoal , dust , salt etc and gi protection pipe , medium grade 15mm bore and gi watering pipe 20mm bore light grade , 40mm thick precast rcc m 15 ( nomial mix ) cover reinforced with xpm weight not less than 4 kg / sqm with suitable handle of 6mm dia ms bar and angle iron 40x40x3mm frame for cover , pcc m 15 ( nominal mix ) pit , excavation and earth work in any type of soil and connected , complete all as specified & directed . note: 1 . earth lead & protection pipes length upto & including 7 . 50 metre is deemed included in the unit rate quoted by the contractor . 2 . earth filling shall be done by vegitable soil . 3 . soil should be free fromstone , boulders , aggregate , gravels etc . , ( o ) all as per item no ( n ) above but using with earth lead gi strip of size 32 x 6 mm with gi pipe 40 mm dia for protection of earth lead and 20 mm dia for watering pipe as shown in the earthig drawing electrical plate no 3 on ssr i complete all as specified and directed by engr in charge . , ( p ) s&f hdpe pipe on wall / floor includding all fittings of 40mm bore for passing of cables from panel to pumpset complete all as directed by engr in charge . note : ( i ) any other items required for smooth operation / functioning of pumping sets are deemed to be included in the quoted rates by the contractor . ( ii ) the work to be done as per the drawing attached on appx a & appx b . ( iii ) the size of inlet and outlet pipe for pumping set...

Diesel Locomotive Works - Punjab

20269709 tender for set of lead wires for hitachi item list : ( 1 ) set of lead wires for hitachi tm stator of 15250a tm type ( one set consisting of the following ) ( 1 ) lead wire a drg no.3twd.095.067 qty.01 no. ( 2 ) lead wire drg no.3twd.095.069 alt 1 qty.01 no. ( 3 ) lead wire aa drg no.3twd.095.068 alt 1 qty.01 no. ( 4 ) lead wire f drg no. 3twd.095.073 alt 1 qty.01 no. ( 5 ) lead wire ff drg. no.3twd.095.074 alt 2 qty.01 no. ( 6 ) lead wire drg no.3twd.095.071 alt 1 qty.02 nos. ( 7 ) lead wire drg no.3twd.095.070 alt 2 qty. 02 nos. ( 8 ) lead wire drg no.3twd095.072 alt 1 qty.01 no. ( 9 ) connector for main pole drg. no.4twd 092 510 qty.05 nos. confirming to specification no. 4tms / 095 / 028 or latest & e 0028 or latest for hitachi traction motor type hs 15250a for elect.loco...

Diesel Locomotive Works - Punjab

18351670 tender for set of lead wire, each set consist of 5 items . to drg no.3twd.095.057 alt 7 qty = 01 nos,3twd.095.058 alt 7 qty =01 nos , 3twd.095.075, qty = 02 nos, 3twd.095.076 qty = 01 nos, 3twd.095.077qty=01 nos for hitachi traction motor type 15250 a for elect.loco....

Diesel Locomotive Works - Punjab

17706772 tender for set of lead wires for hitachi tm stator of 15250a tm type (one setconsisting of the following) (1) lead wire a drg no.3twd.095.067 qty.01 no. (2) lead wiredrg no.3twd.095.069 alt 1 qty.01 no. (3) lead wire aa drg no.3twd.095.068 alt 1 qty.01 no.(4) lead wire f drg no. 3twd.095.073 alt 1 qty.01 no. (5) lead wire ff drg. no.3twd.095.074alt 2 qty.01 no. (6) lead wire drg no.3twd.095.071 alt 1 qty.02 nos. (7) lead wire drgno.3twd.095.070 alt 2 qty. 02 nos. (8) lead wire drg no.3twd095.072 alt 1 qty.01 no. (9)connector for main pole drg. no.4twd 092 510 qty.05 nos. confirming to specificationno. 4tms/095/028 or latest & e 0028 or latest for hitachi traction motor type 15250afor elect.loco...

Diesel Locomotive Works - Punjab

17706581 tender for set of lead wire, each set consist of 5 items . to drg no.3twd.095.057 alt 7 qty = 01 nos,3twd.095.058 alt 7 qty =01 nos , 3twd.095.075, qty = 02 nos, 3twd.095.076 qty = 01 nos, 3twd.095.077qty=01 nos for hitachi traction motor type 15250 a for elect.loco....

National Institute Of Pharmaceutical Education And Research Niper - Punjab

17241056 supply of 1 borosilicate glass capillary, od 1mm id point 58 mm l 150 mm 2 borosilicate glass capillary , od 1mm id point 58 mm l 75 mm 3 q series electrode holder , with 1 mm pin threaded collar for patchclamp with port wire and straight 1 mm od 4 ag wire , diameter point 25 mm and 2 m l 5 glass seal compression cap, for model qc 10 type electrode holder polycarb for glass holder 1mm od 6 glass seal compression cap , for model qc 12 type electrode holder polycarb for glass holder 1 mm od 7 glass seal compression cap , for model qc 15 type electrode holder polycarb for glass holder 15 mm od 8 cover glass , 25 mm round shape thickness 9 cover glass , 25 mm round shape thickness 1 5 10 disc electrode , for model e 243 with 20 cm lead wire attached to the back edges which should make with the electrical contact each other with 8 mm diameter 11 slice anchors , for the open bath chambers they control the 12 slice anchors , for the open bath chambers they control the ancher pressure applied to the slice it is made of type 316 stainless steel with plastic coating for rc 40 chamber 1 5 mm 13 slice anchors , for the open bath chambers they control the ancher pressure applied to the slice it is made of type 316 stainless steel with plastic coating for rc 26 1 mm 14 grease kit, silicon grease kit seal form between the coverslip and chambers cover and with brushes and pallets 15 tubing kit , complete fitting and tubing connecter kit for recording chambers for the perfusion system which made up of polypropylene includes tube to tube reducing y shaped t shaped luer to leur and leur to barb adapters etc 16 nylon mesh kit , it is use for supporting and holding slice for recoding chambers nylon mesh in two size in 0 3 mm and 1 3 mm mesh opening and 2 and 12 mm thickness 17 polyethylene tubing, length 3 m diameter od 0 97 mm id 0 58 mm 18 poly ethylene tubing , length 3 m diameter od 1 27 mm id 0 86 mm...

Diesel Locomotive Works - Punjab

16937333 tender for set [motor set] of mp/cp coils with shoes fully potted, interconnectorsand lead wires for hitachi tm stator, type hs 15250a, confirming to clwsspecification no. 4tms.095.032 alt 4 & 033 alt 4. details description as per annexureattached with tender documents....

Diesel Locomotive Works - Punjab

16549928 tender for set of four fluoro elastomer insulated lead wire for brush gearconnector for tm bg 150 sq.mm. to drg. no.4/dmw/m/tm 429, alt z : 4/dmw/m/tm 323, alt v :3/dmw/m/tm 475 : 3/dmw/m/tm 476, alt x : 3/dmw/m/tm 477 (alt y), 478 (alt y), 479 (alt y) tordso specification no.mp.0.52.00.08 (rev 04) june 2012 & mod. sht no.mp.mod.em.06.26.00(rev 01) dt.10.05.07...

Diesel Loco Modernization Works - Punjab

2488379 supply of two items of 1500 volt fluonlex insulated wire 150 sq. mm & 200 sq. mm and two items of set of four fluoroelastomer insulated lead wire and lead cable 150 sq. mm & 200 sq. mm....