Water Supply And Sanitation Department - Punjab

37329590 tender for cleaning of pipe line 3” through scour. excavation bailing out water, dismantling brick paving and refilling earth in original condition 2)repair of sluice valve including cost of c.i. spindle, check nut & nutt bolts for sluice valve 3” for sluice valve 6” 3)repair of pipeline including cost of c.i. d joint, nutt bolt, coupler, and excavation bailing out water, dismantling brick paving and refilling earth in original condition. for pvc pipe 3” for pvc pipe 6” 4)repair of expansion joint including cost of jain dori, nutt bolt, rubber jain, t&p, and shuttering etc. for expansion joint 3” for expansion joint 4” 5)repair of leakages in wall, bottom dome of ohsr with water proof material and p/f ms wire mesh....

Water Supply And Sanitation Department - Punjab

37314319 tender for annual maintenance of wss rangilpur block batala cleaning of pipe line 3 ^ prime prime through scour. excavation bailing out water, dismantling 6 1 brick paving and refilling earth in original condition repair of sluice valve including cost of c.i.. spindle, check nut & nutt bolts for sluice valve 3 ^ prime prime for sluice valve 6 ^ prime prime 1 repair of pipeline including cost of c.i. d joint, nutt bolt, coupler, and excavation bailing out water, dismantling brick paving and refilling earth in original condition. for pvc pipe 3 ^ prime prime for pvc pipe 6 ^ prime prime repair of expansion joint including cost of jain dori, nutt bolt, rubber jain, t&p, and shuttering etc. for expansion joint 3 ^ prime prime for expansion joint 4 ^ prime prime repair of leakages in wall, bottom dome of ohsr with water proof material and p/f ms wire mesh....

Military Engineer Services - Punjab

35563858 tender for addn / altn of 134 jco and or pre map md accn at abohar mil stn ( job no 10camwp / 2022 23 / 01 ) taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) areanot exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by engineer in charge. 3 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) areaexceeding 1.50 sqm but not exceeding 4 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by engineer in charge. 4 taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets / planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by engineer in charge. 5 supply & fixing aluminium sliding windowthree trackwith frame & two glass shutters using 4 mm thick glass tinted modi guard and oneshutter with stainless steel wire gauge wirecloth 0.31 mm nominaldia of wire and width of aperture 1.61 mm using aluminium powder coated section ( minimum thickness of powder coating not less than 50 micron ) including approved fittings like aluminium cleat, pvc track, bearing, handle lock, rubber beading etc complete all as specified and as directed by engineer in charge.note: size of aluminium section of make jindal main 2010 or equivalent in make mentioned in appx a to pss ii ( equivalency approved by ge ) shall be as under : ( i ) three track top and vertical section no 20621. ( ii ) three track bottom sectionno 20620 ( iii ) shutter vertical section section 20604 ( iv ) shutter top and bottom section 20604 ( v ) shutter vertical middle ( interlock ) section 20605 ( vi ) cost of glass and wire cloth shall be included in the unit rate. 6 supply & fixing aluminium anodised frame, made out of aluminium sectionpowder coated ( minimum thickness of powder coating not less than 50 micron ) for window, ventilators and aluminium partition with one or more rebates including joining cleat for fixing etc., the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners. aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and as directed by engineer in charge.note : the weight of each section shall be physically ascertained through a board of officers convened by ge and payment shall be made only after the actual weight at site. 7 supply & fixing anodised aluminium window shutter ( glazed or gauzed ) , side hung type without sash bars, made out of aluminium section weighing not less than 0.55 kg / mtr, powder coated ( minimum thickness of powder coating not less than 50 micron ) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings ( each shutter ) such as peg stays 150mm long ( 1 no ) , hinges type b 21 100mm long ( 2 nos ) suitable handle ( 1 no. ) , complete all as specified and as directed by engineer in charge.note : aluminium chowkhat / frame, glass, wiremesh and grill where required shall be measured and paid separately under appropriate item of boq. 8 supply & fixing aluminium powder coated grill weight not less than 1.50 kg / sqm in windows, ventilators including fixing material complete all as specified and as directed by engineer in charge. 9 supply & fixing fiber glass reinforced plastic ( frp ) door frame of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. the laminate door frame moulded with two resistant grade unsaturated polyester plain and chopped mat. door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiber glass from all sides. m.s. stay shall be provided at the bottom to steady the frame., complete all as specified and as directed by engineer in charge. 10 supply and fixing to existing door frames 30mm thick glass fibre reinforced plastic ( frp ) panelled door shutter of required colour and approved brand and manufacture made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick frp laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick frp laminate for panels conforming to is: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of engineer in charge. 11 supply & fixing factory made prefabricated pressed steel door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary ms rawl plug / bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with locking arrangement using mild steel mortise lock 4 levers with 2 nos of keys of size 100mm ( make godrej / harison / navtal ) including ms chromium plated handle and 2 nos ms locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by ms sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface ( not visible from front ) and hammer tone paint on exterior surface ( visible from front ) as per godrej pattern including taking out old shutter with frame complete all as specified and as directed by engineer in charge. 12 material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick pvc sheet ( prelam ) having one side decorative laminated sheet ( for shutter, back side of cabinet, sides of cabinet, partition and shelves etc ) . all the edges of shutter and front exposed edge of partition / shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. including all required fixing material such as ss brackets, screws, adhesive etc., including taking out old any type cabinet complete all as specified and as directed by engineer in charge.note : ( i ) the area of each sheet ( shutter, back side of cabinet, sides of cabinet, partition and shelves ) shall be measured in sqm for payment. ( ii ) magnetic catcher, handle / knob, continuous piano hinges and pvc frame ( where required ) shall be measured and paid separately under appropriate item of boq. ( iii ) any other material required for making / fixing / hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. 13 supply and fixing magnetic catcher fixed with steel screw complete all as specified and as directed by engineer in charge. 14 supply and fixing 40mm dia, cupboard knobs brass, fixed with nut, screw and washer bright finish complete all as specified and as directed by engineer in charge. 15 supply & fixing continuous ( piano ) hinges, stainless steel, bright finish, width of flap when open 30mm complete all as specified and as directed by engineer in charge . 16 supply and fixing solid pvc frame ( single rebated ) of size 60mm x 30mm made out of solid pvc foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal csk screws complete all as specified and as directed by engineer in charge. ( note : frame shall be elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life ) 17 supply and fixingfactory made pressed steel frames of size 125 x 60mm ( thickness of sheet shall be 1.25mm ) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable nos as directed for each leaf, and making good the wall with plaster in cm 1:6 complete all as specified and as directed by engineer in charge.note : butt hinges shall be measured and paid separately under appropriate item of boq as supply only. 18 supply and fixingfactory made pressed steel frames of size 105 x 60mm ( thickness of sheet shall be 1.25mm ) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable nos as directed for each leaf, and making good the wall with plaster in cm 1:6 complete all as specified and as directed by engineer in charge.note : butt hinges shall be measured and paid separately under appropriate item of boq as supply only. 19 material and labour for pcc ( 1:3:6 ) type c 1, using 20 mm graded aggregated as in back filling of pressed steel door frame / chowkhat and bed block for fixing of hold fast complete all as specified and as directed by engineer in charge 20 supply & fixing factory made plain framed panelled shutter 35mm thick made out of 2nd class hard wood with lock rail and panel ( two panels ) inserts of 9mm bwp commercial ply. the size of rails and styles as per is 1003 ( part i ) , kiln seasoned and chemically pressure treated complete all as specified and as directed by engineer in charge. 21 supply & fixing factory made glazed and skeleton shutter 35mm thick made out of 2nd class hard wood kiln seasoned and chemically pressure treated, open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, fitted with cut and mitred beads for securing glass, gauze etc.; sizes of members of shutters as specified in ssr part i, section 8, clause 8.24 ( a ) ;complete all as specified and as directed by engineer in charge. 22 supply only 100mm long stainless steel butt hinges heavy duty type b 21 complete all as specified and as directed by engineer in charge. 23 supply and fixing 100mm long stainless steel butt hinges heavy duty type b 21 including stainless steel screws complete all as specified and as directed by engineer in charge. 24 supply and fixing anodised aluminium handle cast type 150mm long complete all as specified and as directed by engineer in charge. 25 supply and fixing in replacement anodised aluminium handle cast type 150mm long complete all as specified and as directed by engineer in charge. 26 supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm longcomplete all as specified and as directed by engineer in charge. 27 supply and fixing in replacement aluminium anodised barrel tower bolt of extruded section, 200mm longcomplete all as specified and as directed by engineer in charge. 28 supply & fixingaluminium anodised sliding door bolts 300mm long, with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by engineer in charge. 29 supply & fixing in replacement aluminium anodised sliding door bolts 300mm long, with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by engineer in charge. 30 supply & fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm, complete all as specified and directed by engineer in charge. 31 supply & fixingin replacement floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm, complete all as specified and directed by engineer in charge. 32 supply and fixing mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to frame with screw complete all as specified and as directed by engineer in charge. 33 supply & fixingin replacement mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to frame with screw complete all as specified and as directed by engineer in charge. 34 supply and fixing curtain rod 25mm dia ms pipe with ivory coloured pvc coated, wall thickness of pipe not less than 20 guage, including fancy type brackets and pair of decorated end knobs ( finials ) , stop roller etc. as per site requirement, fixed to wall with fixing accessories, including taking down old existing curtain rods any description complete all as specified and as directed by engineer in charge. 35 supply & fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by engineer in charge 36 supply & fixing in replacement stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by engineer in charge 37 supply & fixing 4mm thick sheet glass ordinary quality in squares / retangular not exceeding 0.5sqm in each pane ( aluminium window / ventilator ) complete all as specified and as directed by engineer in charge. note : aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window / ventilator of boq. 38 supply & fixing, 4mm thick figured glass pin head type in squares / retangular not exceeding 0.5sqm in each pane complete all as specified and as directed by engineer in charge.note : aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window / ventilator of boq. 39 roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc. complete all as specified and as directed by engineer in charge. 40 material and labour for non skid ceramic light coloured tiles7 to 8 mm thick squarearea of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile includingnecessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer ( screed bed ) in cement mortar ( 1:6 ) and finish the surface rough to receive the tile complete all as specified and directed by engineer in charge. 41 material and labour for non skid ceramic light coloured tiles 7 to 8mm thick square or rectangular as in skirting ( cut from same size and type as floor tile ) , dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile includingnecessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer ( rendering ) in cement mortar ( 1:4 ) and finish the surface rough to receive the tile including making good plaster surfaces ( above skirting tile ) to match the existing complete all as specified and as directed by engineer in charge. 42 demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge. 43 material and labour for glazed ceramic coloured tiles light shade of size 300mmx 450mm, 7mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer ( rendering ) in cement mortar ( 1:4 ) and finish the surface rough to receive the tile complete all as specified and as directed by engineer in charge. 44 dismantling of stone slabs of any description or thickness in floors, plateform, apron etc laid bedded and pointed in any mortarincluding removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge. 45 material and labour 18 20mm thickness approved shade granite of minimum size equal to width of slab ( not less than 610mm ) machine cut, granite duly factory grinding and polishing and chamfering the outer edges ( table rubbed and mirror polished ) as in cooking platform and like laid over and including 20mm thick cement mortar ( 1:4 ) screed bed including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by engineer in charge. 46 material and labour for machine cut 20 to 25 mm thick, kota stone slab ( size of slab not less than 550x450mm for flooring and in single piece for treads of staircase ) , laid over and including 20 mm thick bedding layer in cement mortar ( 1:6 ) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing / grinding ( mirror finish ) andpolishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by engineer in charge. 47 material and labour for machine cut 18mm thick, kota stone slab as in skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar ( 1:3 ) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing / grinding ( mirror finish ) and polishing by machine, including machine cutting to make it square or rectangularcomplete all as specified and as directed by engineer in charge. 48 demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge 49 material and labour for water proofing treatment to sunken slab and adjoining vertical surfaces as per any one of the two method as specified in pss ii respective clause of ca complete all as directed by engineer in charge / ge. note : ( i ) work shall be executed through specialized agency ( ii ) the treatment shall be carried out as per the manufactures instructions and as directed by the engineer in charge. the name of firm shall be got approved from cwe before carrying out the work. ( iii ) only plan area will be measured for payment. treatment should be continue upto 450mm height on vertical walls. ( iv ) pcc filling under sunken area will be measured & paid separately. 50 material & labour for pcc ( 1:5:10 ) type e2 using 40mm graded stone aggregate as filling of sunken floors complete all as specified and as directed by engineer in charge. 51 material & labour for 40 mm gi pipe medium grade, made to shape as in spout pipe 60cm long in sunken / verandah / balcony including making hole and making good with cement mortar complete all as specified and as directed by engineer in charge. 52 dismantling brick terracing tiles single layer from roof laid and pointed in cement mortar ncluding cleaning and stacking serviceable tiles for re use and balance unserviceable tiles removing from the site complete all as specified and as directed by engineer in charge. 53 demolition / taking out of mud from roofs, any thickness, including removing / cutting uprooting grass, vegetations and roots of small plants etc on roof and surrounding / parapit wall etc, including removing rubbish material from building and thrown in low lying empty area ( as per direcction of age ) at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge 54 material and labour for preparing surface of top roof slab including sides of parapits and cleaned of all foreign materials such as fungues, moss, dust, loose particle etc by wire brushing, sprinkling water on the surface and ensure water does not stand anywhere. if it is so, the roof surface shall be leveled with cement mortar and after that surface shall be painted with one coat of cold applied bituminous primer @ 0.40 ltr per sqm, applied over primed surface app based polymeric membrane minimum weighing 3 kg / sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt. not less than 150 gms / sqm ) laid on primed surface by forced application, torching with overlaps as recommended by the manufacturer complete all as specified and as directed by engineer in charge. 55 material and labour for pcc ( 1:4:8 ) using brick aggregate as in roof minimum average thickness 75mm and increasing uniformly towards ridges to obtain a chain slope 1:40, the top shall be trowelled with the addition of jaggery solution and finished smooth complete all as specified and as directed by engineer in charge. 56 material and labour for 40mm thick brick tiles laid / bedded on screed bed 15mm thick in cement mortar ( 1:6 ) , on existing lime concrete surfaces of roof, joints grouted flush in cement mortar ( 1:3 ) mixed with liquid wpc @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of mes sch part i ( 2009 ) complete all as specified and as directed by engineer in charge. ( note : water proofing compound shall be measured & paid separately as supply only ) 57 material and labour for 40mm thick brick tiles ( old serviceable tiles obtained from demolition / dismantled itemshall be reused ) laid / bedded on screed bed 15mm thick in cement mortar ( 1:6 ) , on existing lime concrete surfaces of roof, joints grouted flush in cement mortar ( 1:3 ) mixed with liquid wpc @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of mes sch part i ( 2009 ) complete all as specified and as directed by engineer in charge. ( note : water proofing compound shall be measured & paid separately as supply only ) 58 material and labour for covering the crumple joint between walls, beams, columns by 0.56 mm thick plain aluminium sheeting, alloy 31000 h4 in ridges, hips, valley gutter, drip and straight flashing ( length and girth as fixed ) including fixing material and takig out old sheet complete all as specified and as directed. 59 providing and injecting approved grout in proportion stirrer mixed acrylic polymer of approved make @ 2% of weight of cement used modified cement slurry non shrinks compound in concrete / rcc work. made with recommended by the manufacture into cracks / honey comb area of concrete / masonry by suitable gun / pump at required pressure including cutting of nipples after curing etc. complete as per directions of ge. note : the payment shall be made on the basis of actual weight of approved grout injected. 60 material and labour for 75 mm thick pcc ( 1:3:6 ) type c 2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning point, filling the joints withbituminous sealing compound of grade ‘a’ / bitumen mastic filler / sealant complete all as specified and as directed by the engineer in charge. 61 taking up or down existing galvanised steel water tubing ( gi pipe ) 15mm bore including fitting / connection from wall, ceiling, floor etc. complete all as specified and as directed by engineer in charge. 62 re fixing old serviceable 15mm bore galvanised steel water tubing ( gi pipe ) but new fittings like elbow, tee, union, socket, reducer etc. in new or old portion / position to walls, ceiling, floor etc complete all as specified and as directed by engineer in charge. ( note : old serviceable pipe obtained from taking up or down ( here in before ) item of this boq shall be reused after necessary cleaning internally and rerunning the old screw threads as required. 63 supply and fixing galvanized steel tubing ( gi pipe ) medium grade 15mm bore isi marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by engineer in charge. 64 taking up or down existing galvanised steel water tubing ( gi pipe ) 20mm bore including fitting / connection from wall, ceiling, floor etc. complete all as specified and as directed by engineer in charge. 65 re fixing old serviceable 20mm bore galvanised steel water tubing ( gi pipe ) but new fittings like elbow, tee, union, socket, reducer etc. in new or old portion / position to walls, ceiling, floor etc complete all as specified and as directed by engineer in charge. ( note : old serviceable pipe obtained from taking up or down ( here in before ) item of this boq shall be reused after necessary cleaning internally and rerunning the old screw threads as required. 66 supply and fixing galvanized steel tubing ( gi pipe ) medium grade 20mm bore isi marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by engineer in charge. 67 supply and fixing galvanized steel tubing ( gi pipe ) medium grade 40mm bore isi marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by engineer in charge.note for item no 61 to 67 : cost for cutting chases / groove as required for concealed pipe as directed shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. 68 supply & fixing rotational mouldedpolyethylene water storage tank white colour of capacity 500 litres ( cylindrical vertical, triple layered with closed top, isi marked ) , hoisted and fixed in position including making inlet and out let connection including dismantling / taking down of existing unserviceable pvc water storage tanks of any description and capicity with float valve and gate valve complete all as specified and as directed by engineer in charge. 69 supply and fixing ball valves, high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball ( polythene float ) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by engineer in charge.note : the minimum weight of ball valve shall be as given in ssr or in relevant is. 70 supply and fixing gun metal, globe or gate valve ( isi marked ) , with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by engineer in charge. note : the minimum weight of gate valve shall be as given in ssr or in relevant is. 71 supply and fixing in replacement bib tap with wall flange cast copper alloy, chromium plated, fancy type, long body, with round head / knob, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by engineer in charge.cat part no con 107kn of jaquar or techno commercial equivalent in make mentioned in appx b 72 supply and fixing in replacement 15 mm bore chromium plated angle stop valve with wall flange of cast copper alloy chromium plated, fancy typewith round head / knob, screwed down high pressure screwed end for iron pipe or for unions and fixed complete all as specified and as directed by engineer in charge.cat part no con 059kn of jaquar or techno commercial equivalent in make mentioned in appx b 73 supply and fixing central hole single lever basin mixer, 15mm bore, chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for whb including taking out old any type pillar cock / mixer complete all as specified and as directed by engineer in charge.cat part no vgp 81011b of jaquar or techno commercial equivalent in make mentioned in appx b 74 supply and fixing central hole basin mixer valve with regular spout, 15mm bore, brass chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for whb including taking out old any type pillar cock / mixer complete all as specified and as directed by engineer in charge. cat part no con 167knb of jaquar or techno commercial equivalent in make mentioned in appx b 75 supply and fixing in replacement mixer valve with swinging spout ( for sink ) 15mm bore, brass chromium plated, for mixing hot & cold water, screwed down for iron pipe suitable for fixing to wallcomplete all as specified and as directed by engineer in charge. cat part no con chr 309knm of jaquar or techno commercial equivalent in make mentioned in appx b 76 supply and fixing in replacement chromium plated, wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs & wall flanges, screwed ends suitable for15mm bore iron pipe, complete all as specified and as directed by engineer in charge. cat part no con 273knupr of jaquar or techno commercial equivalent in make mentioned in appx b 77 supply and fixing in replacement kitchen rack / dish rack ( kitchen stand or wall mounted ) of size750mmx600mmx250mm ( appx size ) made out of food grade stainless steel 1mm thick sheet / strip including necessary arrangements for plates and utencils to keep ( holds up to many plates or bowls to accommodate several place settings, multipurpose ) , stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories complete all as directed by engineer in charge. 78 supply & fixing in replacement stainless steel sink with drainageboard made out of 1.00mm thick sheet , kitchen or laboratory withplugs, washers, waste pipe includingbedding in cement mortar to dwarf wall or fixing cast iron cantilever brackets and connecting union to waste pipe; overall size 915mm x 460mm with bowl size 405mm x 355mm x 200mm including taking down existing chinaware sink complete all as specified and directed by engineer in charge. 79 supply & fixing in replacement vitreous china oval shape slim / thin rim ceramic wash basin, white, flat back of size 550mm x 400mm, counter top / table top including 32mm chromium plated waste coupling and pvc waste pipe including fixing material for wash basin on granite slab and including making hole in granite slab for coupling, complete all as specified and as directed by engineer in charge. 80 supply & fixing in replacement corner vitreous china wash basin, white, flat back of size 450mm x 390mm, including 32mm chromium plated waste coupling and pvc waste pipe including bracket and cutting for and pinning in end of bracket or erecting with long screwed shanks & fly nuts, flange end bedded in red lead cement, complete all as specified and as directed by engineer in charge. 81 supply & fixing in replacement 300 mm long pvc connection 15mm size with brass nuts complete all as specified & directed by engineer in charge. 82 supply & fixing in replacement 450 mm long pvc connection 15mm size with ptmt nuts complete all as specified & directed by engineer in charge. 83 supply & fixing in replacement vitreous china squatting pan orissa pattern white of size 580mmx440mm white with integral foot rests, excluding flushing cistern, flush pipe above floor but including setting the trap and pan in lime concrete ( 1 lime, 2 sand or surkhi and 5 aggretate ) , min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, including pvc flush pipe upto finished floor level, joints of flush pipe and trap make leakproof and testing upto entire satisfaction of engineer in charge before filling concrete complete all as specified and as directed by engineer in charge. 84 supply and fixing in replacement pvc low level cistern of 10 ltrs capacity with top push button inclusive of brackets and pvc bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed by engineer in charge. 85 supply & fixing in replacement cromium plated swivel shower of any colour with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of any colour for fixing with 15mm dia pipe complete all as specified and as directed by engineer in charge.note : the minimum weight 40gms. 86 supply and fixingin replacement pvc bathroom mirror cabinet of appx size 450mm x 350mm x 140mm ( compact mirror cabinet, concealed shelves ) approved quality complete all as specified and as directed by engineer in charge. 87 supply and fixingin replacement chromium plated towel ring round with round flange, fixed on wall with chromium plated brass screws and pvc plug complete all as specified and as directed by engineer in charge. cat part no acn 1121bn of jaquar or techno commercial equivalent in make mentioned in appx b 88 supply and fixingin replacement chromium plated soap dish holder with round flange, fixed on wall with chromium plated brass screws and pvc plug complete all as specified and as directed by engineer in chargecat part no acn 1131n of jaquar or techno commercial equivalent in make mentioned in appx b 89 supply and fixingin replacementcorner pvc shelf assembly fancy type with brackets, fixed with brass screws and pvc plug complete all as directed by engineer in charge. 90 taking down eaves gutters and rain water pvc / ci pipes ( any size or pattern ) including all fittings, heads, shoes, bends, swan neck etc ( measured overall as fixed along the centre line over fittings and accessories ) complete as specified and as directed by engineer in charge 91 supply & fixing 110mm bore pvc ( swr ) pipes single socketed ( pressure rating not less than 4kg / sqcm ) in any length with rubber ring joints for drain or rain water fixed along walls with and including pvc stack clamps ( interval of 1m ) of suitable size, complete all as specified and as directed by engineer in charge. 92 supply & fixing 75mm bore pvc ( swr ) pipes single socketed ( pressure rating not less than 4kg / sqcm ) in any length with rubber ring joints for drain or rain water fixed along walls with and including pvc stack clamps ( interval of 1m ) of suitable size, complete all as specified and as directed by engineer in charge. 93 supply & fixing pvc ( swr ) bends ( any radius ) suitable for 110mm bore pipe complete all as specified and as directed by engineer in charge. 94 supply & fixing pvc ( swr ) bends ( any radius ) suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 95 supply & fixing pvc ( swr ) junction single, ( single t ) equal or unequal with access door suitable for 110mm bore pipe complete all as specified and as directed by engineer in charge. 96 supply & fixing pvc ( swr ) junction single, ( single t ) equal or unequal with access door suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 97 supply & fixing pvc ( swr ) vent cowl suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 98 supply & fixing pvc ( swr ) multi floor trap including jointing with solvent cement suitable for 75mm bore pipe complete all as specified and as directed by engineer in charge. 99 supply & fixing stainless steel grating 125 mm dia with or without waste hole complete all as specified and as directed by engineer in charge. 100 supply & fixing 32mm bore high density polyethylene pipes ( hdpe ) of pressure rating not less than 6kg / sqcm laid in floors / trenches complete all as specified and as directed by engineer in charge.note : ( i ) excavation, earth work if required, shall be measured & paid separately under appropriate item of this schedule. ) 101 excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc. not exceeding 10 sqm on plan and getting out in soft / loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by engineer in charge. 102 returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed. 103 removing excavated material ( surplus soil ) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by engineer in charge. 104 material and labour for pcc ( 1:4:8 ) , type d 2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by engineer in charge. 105 material and labour for pcc ( 1:2:4 ) , type b 1 using 20 mm graded stone aggregate as in coping, mud stops, packing sides / around of interlocking tiles, bed block, for embedded posts & similar work etc including weatherings, slightly roundedor chamfered angles complete all as specified and as directed by engineer in charge. 106 material and labour for providing and injecting chemical emulsion for post constructional antitermite treatment of voids in masonry using chemical emulsion@ one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand ) to match the existing floors complete all as specified and as directed by engineer in charge. 107 material and labour for providing and injecting chemical emulsion for post constructional antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre 300mm apart including drilling depth of holes not less than 300mm and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and as directed by engineer in charge. 108 taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by engineer in charge. 109 material and labour for internal plastering 15mm thick in cement mortar ( 1:6 ) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the engineer in charge. 110 material and labour for rendering / plastering 15mm thick on any face of brick wall or concrete surfaces consisting in two layers i.e. first layer 10mm thick in cement mortar ( 1:4 ) and second ( top layer ) layer 5mm thick in cement mortar ( 1:4 ) including mixing of liquid wpc in mortar @ as per manufacturer instruction per bag of cement of 50kg, finished even and smooth without using extra cementcomplete all as specified and as directed by the engineer in charge. ( note : wpc shall be measured & paid separately as supply only ) 111 material and labour for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster ( 1:4 ) ( 1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster ( 1:1 / 2:2 ) ( 1 cement: 1 / 2 coarse sand : 2 stone chipping 10mm nominal size ) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete as specified and as directed by engineer in charge. note : grooves shall be measured & paid separately 112 material and labour for forming groove of uniform size 12mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as specified and as directed by engineer in charge. 113 supply only liquid water proofing compound complete all as specified and as directed by the engineer in charge. 114 dismantling of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by engineer in charge. 115 material and labour for brick work ( old serviceable bricks obtained from dismantled itemshall be reused ) straight or curved on plan exc. 6 metre mean radius built in cement mortar ( 1:6 ) complete all as specified and as directed by engineer in charge. 116 material and labour for brick work with sub class ‘b’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar ( 1:6 ) complete all as specified and as directed by engineer in charge. 117 material and labour for brick workin half brick thick wall straight or curved on plan exc. 6 metre mean radius built in cement mortar ( 1:4 ) complete all as specified and as directed by engineer in charge. 118 surface dressing not exceeding 15cm deep in soft / loose soilincluding cutting of grass, roots, bushes if any and filling of lower portion with soil obtained from cuttingafter sepration of grass, roots, bushes etc and dressing and removing from site all grass, roots and extra soil if any complete all asspecified and as directed by engineer in charge. 119 material and labour for 75mm thickcement concrete ( 1:4:8 ) , type d 2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed by engineer in charge. 120 supply and laying / fixing 60 mm thick ( m35 grade ) precast interlocking tile / paving block factory made chamfered edge ( made by using pu moulds on vibrating table machine ) using cement concrete and pigment, prepolished & preglazed, with approved colour, design & pattern as in foot parth, parks, lawns, drive ways or light traffic parking etc., laid in required colour & pattern, over and including 50mm thick compacted bed of fine sand cushining, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and complete all as specified and as directed by engineer in charge. 121 supply and laying factory made kerb stone of m 25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar ( 1:3 ) ( 1 cement:3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5mm ) , including making drainage opening wherever required complete all as specified and as directed. 122 demolition of cement concrete reinforced of any description such as slab / oht staging, kitchen chimeny, chajjas, fins, shelves, oht etc, including reinforcement cut as required to facilitate demolition and prepare the surface to casting / jointing newincluding removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by engineer in charge 123 material and labour for reinforced cement concrete m 25 ( design mix ) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by engineer in charge. ( note : reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. 124 material and labour for reinforced cement concrete m 25 ( design mix ) using 20mm graded stone aggregate as in louvers, parapets, railing and like complete all as specified and as directed by engineer in charge. ( note : reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. 125 material and labour for reinforced cement concrete m 25 ( design mix ) using 20mm graded stone aggregate as in chajjas, fascias, fins and like complete all as specified and as directed by engineer in charge. ( note : reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. 126 material and labour for mild steel tmt bars 10mm dia & over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified and as directed by the engineer in charge. ( note : weight of binding wire shall not be considered for measurement and payment purpose. ) 127 material and labour for mild steel tmt bars 6 to 8 mmdiacut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified and as directed by the engineer in charge. ( note : weight of binding wire shall not be considered for measurement and payment purpose. ) 128 material and labour for mild steel tmt bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required including bending, cranking etc and binding with and including ms wire ( annealed ) not less than 0.9mm dia, complete all as specified & directed by engineer in charge. ( note : weight of binding wire shall not be considered for measurement and payment purpose ) 129 form work to soffits of suspended slabs such as flat roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick ( horizontal or sloping ) rough finished complete all as specified and as directed by engineer in charge. 130 formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. vertical or to batter rough finished complete all as specified and as directed by engineer in charge. 131 form work tochullah hoods, chajjas, troughs and similar items including edgesrough finished complete all as specified and as directed by engineer in charge. 132 form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished complete all as specified and as directed by engineer in charge. 133 shotcreting average thickness 25mm in rcc columns, beams and slab etc. ( with mix minimum cement content of 350 kg per cum, m 25 ) . concrete having the specified minimum characteristic compressive strength ( with ordinary portland cement, coarse sand and graded stone aggregates of 6mm maximum size ) incl the cost of centering and shuttering at edges and corner etc as directed by engr in charge incl chipping of unsound / week concrete material 25mm average thickness from slabs, beams / columns etc with mannual chisel or standard power driven percussion type all of approved makes incl tapering of all edges, making square shoulder of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removel of rust by applying approved rust remover chemical and the coating with dr fixit epoxy zinc primer @ 6 sqm per litre at dft of 100 micron as per manufacturers instruction and specification, including removing rubbish material from building and thrown in low lying empty area at any distance from the site as directed complete as specified and as directed by engineer in charge. make : sika / fosroc / pidilite or techno commercial equivalent make approved by ge in writing from e in cs approved list.note : complete treatment to be executed by approved applicator. 134 supply and fixing hard drawn steel wire fabric not exc 4kg / sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means ofl shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding / l clip / tying with mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified and as directed. 135 material and labour for rendering 5mm thick in cement mortar ( 1:3 ) on surface of ceiling after shotcreting treatment, finished even and smooth without using extra cement complete all as specified and as directed by the engineer in charge. 136 dismantling wrought iron or mild steel work of any description complete all as specified and as directed by engineer in charge. 137 excavation in post holes in soft / loose soil n. exc 0.50 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm including removing of surplus spoil to a distance n exc 50 mtr and making good the disturbed surfaces all as specified and directed by engineer in charge. 138 material and labour for pcc ( 1:3:6 ) , type c 2 using 40 mm graded stone aggregate as in foundation filling and mass concrete, in post hole, bed block& similar work etc including form work complete all as specified and as directed by engineer in charge. 139 material and labour for mild steel framed work such as grills, ladder, cooler stand, cloth drying provision, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to fe.290.gde e 165complete all as specified and as directed by engineer in charge. 140 material and labour for structural steel work, framed work made by using rolled mild steel joist, channel, angle, or tee sections, fixed independently distance pieces, cleats or other connecting plates, gusset plates, brackets, bending and welding, riveting etc, and cut to shape, drilled and counter sunk for screw, conforming to gde fe 410 w ( gde e 250 quality a ) complete all as specified and as directed by the engineer in charge. 141 cutting out concrete blocks, slabs, brickwork or stone masonry ( in alter nate course ) , forming tooth ings for and bonding new work in mortar into old work, including new materials entering old wall ie pcc ( 1:3:6 ) type c 1 using 20mm graded stone aggregate and set in cement mortar ( 1:6 ) complete all as specified and as directed by engineer in charge. 142 supply and fixing 4mm dia galvanised iron wire fitted with nut bolts complete all as specified & directed by engineer in charge. 143 material and labour for preparation ofnew steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by engineer in charge. 144 material and labour for preparation ofnew wooden or wood based surfacesof any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by engineer in charge. 145 material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying two coats of synthetic enamel paint ( 1st quality ) of approved tint / colour to achieve glossing finish with using paint brush complete as specified and as directed by engineer in charge. 146 material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying two coats of synthetic enamel paint ( 1st quality ) of approved tint / colour to achieve glossing finish with using paint brush complete as specified and as directed by engineer in charge. 147 material and labour for preparation ofnew plastered internalwall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of acrylic emulsion of approved tint over a coat of primer by using paint brush / roller. 148 material and labour for preparation ofnew plastered external wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of exterior acrylic emulsion of approved tint over a coat of primer by using paint brush / roller. 149 material and labour for preparation ofnew plastered or concrete surface of ceiling surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) three coats of white wash by using paint brush. 150 material and labour forpreparation of old decorated surfaces ( plastered / unplastered ) of ceiling by remove / scraping down allsmoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean including applyingwall care putty where required for filling to depressions / nail holes / light cracks etc and to make surface even and smooth, and after preparing the surface smooth applying one coat of lime white wash with paint brush complete all as specified and as directed by engineer in charge. 151 material and labour for complete removal of existing treatment on old internal wall surfaces of any desciption, preperation of surface by mechanised sander having suction vaccum bag using smart periodical methodology and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface / nail holes / light cracks etc and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of acrylic emulsion of approved tint over a coat of primer on old prepared surface by using paint brush / roller.note : contractor may use manual scraping tools for complete removal and surface prepration with prior approval of engr in chrge in case of places where using of mechanical equiment are not posiible. 152 material and labour for complete removal of existing treatment on old external wall surfaces of any desciption, preperation of surface by mechanised sander having suction vaccum bag using smart periodical methodology, complete all as specified and as directed by engineer in charge and applying the following: ( a ) applying wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface / nail holes / light cracks etc and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of exterior acrylic emulsion of approved tint over a coat of acrylic emulsion external primer on old prepared surface by using paint brush / roller. note : contractor may use manual scraping tools for complete removal and surface prepration with prior approval of engr in chrge in case of places where using of mechanical equiment are not posiible. 153 material and labour forpreparation of old decorated surfaces ( plastered / unplastered ) of walls / pillars / cornices by remove / scraping down allsmoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by engineer in charge: ( a ) applying wall care putty where required for filling to depression of scraped surface / nail holes / light cracks etc and smoothening the surfcae with sand papers / mechanised sanding etc prepatory to paint as directed. ( b ) two coats of acrylic emulsion of approved tint on old prepared surface by using paint brush / roller. 154 b / r portion 155 taking down carefully existing copper / aluminium point wiring ( light / fan / sockets / bell / power point ) complete with all accessories such as switch socket with sheet, ceiling rose, lamp holder including rusted / broken concealed conduit, junction and sunken boxes etc and removing dismantled material and making good disturbed surface of walls / floors etc matching with existing surface complete all as specified and as directed by engineer in charge. 156 material and labour for concealed point wiring for one light point / fan point controlled by one switch ( using red, black and green etc colour wires as colour coding ) complete with 1.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including 2mm thick galvanised steel pressed sunken terminal boxes ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switches / socket / regulator shall be measured and paid separately under appropriate item of boq / sch a ) . 157 all as per above srl item no. 156 but for onesocket out let 5 amps point controlled by one switch ( on same board ) complete all as specified and as directed by engineer in charge. ( switches, sockets etc. shall be measured and paid separately under appropriate item of boq / sch a ) . 158 all as per above srl item no. 156 but for one socket out let 5 amps point controlled by one switch ( on independent board and not below the any other switch board ) complete all as specified and as directed by engineer in charge. ( switches , sockets etc. shall be measured and paid separately under appropriate item of boq ) . 159 all as per above srl item no. 156 but for call bell point ( on independent board ) complete all as specified and as directed by engineer in charge. ( switches shall be measured and paid separately under appropriate item of boq ) . 160 material and labour for concealed point wiring for one light point controlled by two nos two way switch ( using red, black and green colour wires as colour coding ) complete with 1.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box etc, including 2mm thick galvanised steel pressed sunken terminal boxes ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switch, including provn of 1.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switches shall be measured and paid separately under appropriate item of boq ) . 161 material and labour for concealed point wiring for onesocket out let 15 / 16 amps point controlled by one switch ( on independant board ) ( using red, black and green colour wires as colour coding ) complete with 2.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, including 2mm thick galvanised steel pressed sunken terminal boxes of ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 2.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switch, socket shall be measured and paid separately under appropriate item of boq ) . 162 material and labour for concealed point wiring for onesocket out let 15 / 16 amps point controlled by one switch ( on independant board ) ( using red, black and green colour wires as colour coding ) complete with 4 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through andincludingpvc conduit 20mm dia ( medium duty, isi marked ) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, including 2mm thick galvanised steel pressed sunken terminal boxes of ( min 60mm deep, suitable size ) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 4 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls / ceiling / floors etc. by using cm ( 1:3 ) complete all as specified and as directed. ( switch, socket shall be measured and paid separately under appropriate item of boq ) . 163 taking down carefully existing copper / aluminium point wiring ( light / fan / sockets points ) complete with all accessories such as switch with sheet, ceiling rose including rusted / broken concealed sunken boxes etc but except concealed conduit and junction boxes and removing dismantled material and making good disturbed surface of walls / floors etc matching with existing surface complete all as specified and as directed by engineer in charge. 164 material and labour for concealed point wiring for one light point / fan point / bell point controlled by one switch ( using red, black and green colour wires as colour coding ) complete with 1.5 sqmm ( nominal cross section area ) single core frlsh pvc insulatedunsheathed and multi strand copper conductor cable 1100 volt ( isi marked ) drawn through existing pvc conduit but including 2mm thick galvanised steel pressed sunken terminal boxes of suitable size ( min 60mm deep, suitable length ) concealed in wall, 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 sqmm single core frlsh pvc insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. complete all as specified and as directed. ( switches, regulator shall be measured and paid separately under appropriate item of boq ) . note: where ever it is not feasible to cable drawn through existing pvc conduit in roof salb ( for ceiling fan point only ) due to blocked, casing caping shall be provided by contractor without any extra cost, cost for the same shall deemed to be included in the quoted unit rate. 165 supply and fixing switch piano flush type ( isi marked ) , 5 / 6amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by engineer in charge. note ; laminated sheet shall be measured and paid in point wiring item of boq. 166 supply and fixing switch piano flush type ( isi marked ) , 5 / 6amps, single pole, two way fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet and covering frame shall be includedin point wiring item of boq ) . 167 supply and fixing switch piano flush type ( isi marked ) , bell push, 5amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 168 supply and fixing socket outlet multipurpose type ( isi marked ) , 2 in 1, 5 pin, 5 / 6 amp, flush type fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 169 supply and fixing socket outlet multipurpose type ( isi marked ) , 2 in 1, 6 / 5 pin, 6 amp and 16 amp, flush type fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 170 supply and fixing switch piano flush type ( isi marked ) , 15 / 16amps, single pole, one way complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) . 171 supply and fixing ceiling rose ( isi marked ) surface type polycarbonate isolated body three terminal, topline series 65x50mm, 6 amp, complete all as specified and as directed by engineer in charge. 172 supply and fixing angle lamp holder ( isi marked ) polycarbonate cased body ( b22 base ) , top line series, with back plate, 6amps, complete all as specified and directed by engineer in charge. 173 supply and fixingelectric calling bell ding dong type, ac 230 volts single pole including making elctric connection and testing, complete all as specified and as directed by engr in charge. 174 supply and fixing mcb ‘b’ curve suitable for 240 volts ac supply, 06 to 32 amps, sp with over load and short circuit protection and rupturing capacity not less than 10 ka, fixing in db / panel complete all as specified and as directed by engineer in charge 175 supply and fixing mcb ‘b’ curve suitable for 240 volts ac supply, 32 40 amps, spn with over load and short circuit protection and rupturing capacity not less than 10 ka, fixing in db / panel complete all as specified and as directed by engineer in charge 176 supply and fixing in replacement ( concealed flush to wall ) factory made db ( made out of crca sheet not less than 1.2mm thick, fitted with din channel neutral link and 200 amp rated bus bar ) spn, 12 way 240v, suitable for mounting mcb / isolator, conforming to is 13032, db shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. the db shall be double door type with hinged door with locking arrangement, the dbs shall be same make as mcbs, db shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. the dbs shall be of ip 43 protection class, including taking down unserviceable old db any type including mcb etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by engineer in charge.note : mcb’s shall be measured and paid separately under appropriate item of boq. 177 supply and fixing in replacement of led complete fitting including batten, t 8 retro led polycarbonate 1 x 20watt, appx 4 feet long, with decorative ultra ceiling square profile linear led lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23 / 0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts. ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.95 ( e ) thd : max10%. ( f ) ip rating : ip 20. ( g ) crca pre coated housing with two coloured plastic end cap. ( h ) led driver of the same make as of the luminaire. ( j ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( k ) surge protection minimum 2.5 kv. ( l ) cct : minimum 6000k ( m ) cri : minimum 80 ( n ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 178 supply and fixingin replacement led light fitting 1 x 10watt, appx 2 feet long with decorative ultra ceiling square profile linear led lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23 / 0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.95 ( e ) thd : max 10%. ( f ) ip rating : ip 20. ( g ) crca pre coated housing with two coloured plastic end cap. ( h ) led driver of the same make as of the luminaire. ( j ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( k ) surge protection minimum 2.5 kv. ( l ) cct : minimum 6000k ( m ) cri : minimum 80 ( n ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 179 supply and fixing in replacement of led bulkhead fitting 1 x 10watt, complete with standard profile linear led lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23 / 0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 50°c ( d ) power factor : minimum 0.95 ( e ) thd : max 10%. ( f ) ip rating : ip 65. ( g ) cct : 6500k ( h ) impact resistant polycarbonate housing, polycarbonate diffuser with silicon gasket ( j ) led driver of the same make as of the luminaire. ( k ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( l ) surge protection minimum 2.5 kv. ( m ) cri : minimum 80 ( n ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 180 supply and fixing in replacement led lamp minimum 3 star rated 9 / 10 w led b 22 base complete all as specified and directed by engr in charge with following specifications ( a ) lumen system efficacy of lamp should be minimum 100 lumen per watt. ( b ) input voltage range : 160 to 270 volts ( c ) temp operating range : minus 10°c to plus 50°c ( d ) power factor : minimum 0.90 ( e ) cri: minimum80 181 supply and fixing in replacement energy efficient led security light fitting of 25w pressure die cast aluminium housing / body, heat resistant clear toughened glass, better optics for uniform distribution street luminaire, with driver, including electric connection, fixing the light fitting with existing bracket and clamps but including repalcement of nut bolts if required, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting with old bracket any type complete all as specified and directed by engineer in charge : ( a ) lumen system efficacy of luminaire should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 50°c ( d ) power factor : minimum 0.95 ( e ) thd : max10%. ( f ) ip rating : ip66. ( g ) ik rating:minimum ik07 ( h ) built in potted led driver of the make as of the luminaire. ( j ) led driver should be complete with all protections vizopen / short circuit protection, over voltage protection, all as per standard design of manufacturer. ( k ) surge protection 10 kv ( inbuilt + extended ) ( l ) cct : 5700 k. ( m ) cri: minimum 70 ( n ) lens high efficiency wide angle lens. ( o ) bis approved fixtures and driver ( p ) rated life time : 50000 burning hrs ( average 10 to 12 hrs daily ) 182 supply and hanging / fixing ceiling fan 1200 mm sweep ac supply ( input voltage range ; 120 to280v ) , bldc type, 5 star rated, bee and isi marked super enamelled, copper winding of b class insulation, single phase, minimum 30w ( ± 10% ) , temperature rise 40 degree maximum without remote but with and including capacitive regulator, 03 no blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable sizefrom ceiling rose to fan complete all as specified.note : ( i ) serial number as issued by engr in charge of celing fan and ge office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account 183 supply and fixing exhaust fan ( heavy duty ) steel body, ac single phase 230v, 50 cycle per second, size 300mm sweep with blades and frame including self closing gi louvers off mode protection against birds etc mounted in suitable opening arrangement. including electric connection with and including new flexible sheathed copper wire of size 24 / 0.2mm, 3 core from ceiling rose to fan ( not exceeding 0.5 mtr long ) , and hanging on wall with 4 nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by engineer in charge.note : serial number of exhaust fan issued by engr in charge and ge office name shall also be written on fan with red colour permanent marker. 184 supply and fixing ventilating air fresher fan of size 250mm sweep, single phase, 1200rpm, copper winding, made of sturdy engineering plastic complete with louvers shutter, including provision of cutting of wall for suitable opening as per fan and making good the disturbed surface as per existing, including electric connection with suitable flexible copper cable from ceiling rose to fan complete all as specified and as directed by engineer in charge. 185 material and labour for concealed sub main wiring ( two run for main i.e. phase and netural and one run for continues as earth wire connected to earth dolly etc., using red, black and green colour wires as colour coding ) with 6 sqmm single core, frlsh pvc insulated multistrand copper conductor drawn through and including pvc conduit 25mm dia ( medium quality isi marked ) , on independent circuit from db including all fitting arrangement i.e. pvc clamp, rawl plug, screw, terminal / junction box, tee, bend etc. and including cutting of chases in wall, taking out old sub main wiring of any conductor any sizefrom conduit and taking down old unserviceable conduit with fittings, and making good disturbed surfaces of walls as per original complete all as specified and as directed by engineer in charge.note : three run of 6 sqmm copper wire and one run conduit shall be measured as one rm length for payment. 186 supply, installation, commissioning and testing of factory made lt panel board ( main control board ) of minimum size 100cm x 80cm x 25cm fixed on / inside wall ( front side open able, double glass door including locking arrangements and handle ) , dust proof, vermin proof made out of crca sheet 2 mm thick powder coated, suitable arrangement for fixing electronic energy meter 04 nos, including pre wired internal wiring with & including single core, pvc copper conductor unsheathed wire multistanded 6 sqmm including provision of rubber beading and mild steel cable glands and lugs, provision of air fins for ventilation, including comprising of 01 no mccb 100amps fp 16ka 415v for incoming, 04 nos mcb 40amps spn for outgoing, 01 no mcb 10 amps spn for outgoing and copper bus bar 200amps for 3 phase and netural complete including all connections incoming / out going, including taking down old panel board any type with fittings complete all as directed by engineer in charge.note : cost for fixing of old electronic meter after taking out from old panel board shall deemed to be included. 187 supply and fixing electric water heater ( geyser ) storage type abs body of capacity 25 ltrs, 5 star rating, 230v, single phase ac supply, inner tank made out of heavy duty stainless steel sheet ( designed with single weld line, factory tested with hydraulic pressure as per latest is code ) with glass lined coating complete with all accessories such as safety valve, thermostate, nrv, connection piece, pvc connection for hot and cold water, three core pvc insulated pvc sheathed copper conductor flexible cable including 15amp plug suitable for existing socket, including 04 no nut bolts etc for hanging of geyser. nut bolt grouting in wall in pcc ( 1:2:4 ) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and as directed by engineer in charge. 188 material and labour for earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including giearthing wire 4 mm dia by means of gi bolts / nuts / washers and protected by 15 mm bore gi medium grade pipe upto test point or upto main switch board, fixing with 02 nos nuts and bolts. earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common saltall around bottom and top. 20 mmbore gi medium grade pipe for watering and including funnel, wire mesh, pcc chamber pit made with pcc ( 1:3:6 ) type c1 ( using 20 mm graded stone aggregate ) including necessary form work, excavation and earth work in any type ofsoil, returning filling and disposal of surplus soil to a distance not exceeding 50m, pit cover 40mm thick made with rcc ( 1:2:4 ) type b1 ( using 20 mm graded stone aggregate ) including tmt reinforcement 8mm dia @ 75mm c / c both way, ms handle 12mm dia, cover rest on ms angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer, complete all as specified & shown in electrical plate no. 3 ofssr 2009 ( part i ) including taking out / dismantling old unserviceable earthing system complete all as specified and as directed by engineer in charge.note: ( i ) pcc chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. ( ii ) protection pipe and gi earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. ( iii ) the earth testing arrangement should be done by the contractor as per direction of engineer in charge. 189 supply and laying or fixing or laid in trenches / ducts / through pipes / in floors / under roads / under hard standing / along poles and testing, cross linked polyethylene ( xlpe ) lt cable, xlpe insulated, pvc inner sheathed, bedded, galvanised steel strip or wire armoured cable ( heavy duty ) 1100 volt gradewith stranded aluminium conductor having cross sectional area 35 sqmm3.5 core conforming to is 7098 ( part i ) 1988 with upto date amendments, including taking out old unserviceable cable any size complete allas specified and as directed.note : ( i ) excavation, earth work, sand cushioning, brick protection, boring / cutting of road and pipe shall be measured & paid separately under appropriate item of this schedule. ) 190 material and labour for sand cushioning, with dry and clean fine river sand ( for under ground cable ) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed. ( note: punned thickness shall be considered for payment purpose ) 191 supply and laying un reinforced precast concrete cable cover, class lv, type 2 flat, size 300mm x 180mm x 40mm for cable protection cover, laid dry in trenches over the cable , perpendicular to the direction of cable complete allas specified and as directed. 192 supply and fixing in replacement gi tubing light grade of size 50 mm bore, isi marked, fixed along poles / walls or laid in trenches, under road for cable protection including fittings ( elbow, tee, socket etc ) complete all as specified and as directed. ( note: excavation and earthwork as required shall be measured and paid separately under respective item of sch. ) 193 material and labour for cutting of road / floor etc any type upto 45cm width and depth for laying of cable / pipe, after laying of cable / pipe returning filling with soil including spreading, leveling watering and well ramming in layers upto 30cm and top layer 15cm thick filling by using pcc ( 1:3:6 ) type c2 using 40mm graded stone aggregate to match the existing level of road / floor complete all as specified and as directed. 194 boring of holes under road, pavement, hardstanding by using trenchless boring machine or by manual manpower suitable for inserting gi pipe any dia upto 50mm including removal of surplus soil and making good disturbed surface complete all as specified and as directed.note: pipe for inserting as required shall be measured and paid for separately. 195 material and labour for extra wiring for inverter socket out going to db with 1.5 sqmm single core, frlsh pvc ( using colour coding as directed ) insulated multistrand copper conductor drawn through existing conduit ( conduit for point wiring already catered in point wiring item of boq ) including making connection to db and inverter socket ) complete all as specified and as directed by engineer in charge. 196 supply and fixing plug top 5 / 6amp 3 pin good quality suitable for 240 volts, ac supply for inverter socket complete all as specified and as directed by engineer in charge. 197 supply and fixing socket outlet flush type ( isi marked ) , 25amps ( for inverter point ) , fixed on laminated sheet complete all as specified and as directed by engineer in charge. ( laminated sheet shall be measured and paid in point wiring item of boq ) ....

Military Engineer Services - Punjab

35481451 tender for certain repair to esh building and accn in fasf under age br ii at nams &f for 15 mm bor gi tube medium grade freed to wall or under floor incl taking up or down old tube complete including cutting closes and make good in cm 1:3 complete all as specified and directed. 2 s& f in repair20 mm bore g.i tubing in new or old location ( wall / roof ) with all fittings incl taking up or down old tube complete all as specified and directed. 3 fixing only in repair steel tubing and connection 20 mm dia bore to wall and laid in floors incl taking up or down old tube and cleaning for refixing complete all as specified and directed. 4 s&f for rotational moulded polythene 500 litres water storage tanks cylindrical vertical with closed top hoisted and fixed in position incl 20 mm dia float valve with aluminium fitting incl old disconnecting and taking down complete all as specified and directed. 5 all as per item above but 1000 litres water storage tanks. 6 all as per item above but 2000 litres water storage tanks. 7 m&l for brickwork with subclass b bricks ( old size bricks ) , straight or curved on plan exc 6m mean radius, built in cm 1:6 complete incl demolition of brickwork / stone built in cement mortar etcall as specified and directed. 8 all as per item above here in before but except bricks complete all as specified and directed. 9 m&l for brick work with sub class ‘b’ bricks ( old size brick ) straight or curved on plan to any radius in half bricks thick walls, built in cm 1:4 complete incl demolition of brickwork / stone built in cement mortar etc all as directed. 10 m&l for rendering 15 mm thick cement plaster in cm 1:6 onbrick work or concrete surfaces including finished even and smooth without using extra cement all as specified and directed. 11 m&l, rendering 15mm thick in cm 1:4 onof brick work or concrete surfacefinish ever and smooth ( w / o using extra cement ) incl wpc as per user manual complete all as specified and directed. ( wpc will be measured and paid separately ) . 12 m&l, rendering 15mm thick in cm 1:6 onof brick work or concrete surfacefinish even and smooth ( w / o using extra cement ) incl taking down old plaster on brick or stone walls , scrubing down with water etc & dispose off debris where directed by eic, complete all as specified and directed. 13 m&l, rendering 15mm thick in cm 1:4 onof brick work or concrete surfacefinish even and fair ( w / o using extra cement ) incl taking down old plaster on brick or stone walls , scrubing down with water etc & dispose off debris where directed by eic, complete all as specified and directed. note : ( wpc shall be measuared seperatly and @ 3% by weight of cement / 200ml for 50kg cement bags or as per manufacturers instructions ) . 14 supply only liquid wpc complete all as specified. 15 m&l, rendering 10mm thick in cm 1:3 over concrete surface as on ceiling finish even and smooth w / o using extra cement incl taking down old plaster on ceiling , scrubing down with water etc & dispose off debris where directed by eic, complete all as specified and directed. 16 m & l for three coat of white wash incl preparation of new plaster surface of ceiling complete all as specified and directed. 17 m&l for two coat of oil bound distemper by spray machine over one coat of primer on new plasterd surfaces of walls, pillars cornces etc incl prepartion of new plastered surfaces through electrical operated grinder complete all as spd and directed 18 m&l for applying two coats of cement base paints over one coat of primer on walls etc, incl preparing new surfaces of walls by brooming down or by steel wire brushing complete all as directed . 19 m&l fortwo coat ofacrylic smooth exterior emulsion paint on walls, pillars cornices etc surfaces by spray machine over one coat of primer incl preparation of new plasterd surface complete all as spd and directed. note : colour and make as approved by engr in charge 20 m&l for applying two coats of oil bound distemper by spray machine incl preparation of oldsurface by complete removal existing treatement on walls through electrical operated grinder etc, incl necessary minor repair of wall by putty complete all as spd and directed. 21 m&l for applying two coats of cement base paints on walls etc, incl preparation of oldsurface and complete removal existing treatement on wall complete all as specified and directed. 22 m&l fortwo coat ofacrylic smooth exterior emulsion paint on walls, pillars cornices etc surfaces by spray machine on old plastered / unplastered surfaces of walls, pillers, corniceson incl preparation of old surfacesthrough electrical operated grinder complete incl edges overto obtain smooth finish using sand paper, over one coat of primer complete all as specified and directed. 23 m&l for one layer of compound of altek / birla putty 3mm th on old scraped surfaces or new plasterd surfaces and obtain smooth finish using sand paper complete all as spd and directed. 24 m & l for repair to rcc chajjas, roof projection edges , hanging part of chajjas, edges ofchajjas, rcc parapets, under the roof / floor slabs with pcc 1:2:4 ( using 12.5mm crushed graded agg ) incl neccasary renforcement 8mm to 12mm tmt bars , form work, ms wire mesh for boundingthe concreteonground requiredand plaster work in cm 1:3 & periodical services to match with the existing surfaces finishing at any height of buildings etc completed all as specified and directed by engr in charge. 25 s&f in repair for 3mm thick, sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exc 0.5 sqm in each pane fixed with oil putty or beads and incl hacking out glass old complete all as specified and directed. 26 s&f in repair for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples / beading complete all as specified and directed.. 27 m & l for pcc 1:4:8 type d 2 ( using 40 mm agg. ) in sub base of flooring incl demolition complete all as specified and directed. 28 m&l for non skid ceramic any coloured / printedtiles 7 to 8 mm thick ( square / rectangular ) area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floor of shade & designed as approved by ge, set and jointed in neat cement slurry and pointed with white cement with colour pigment to match the colour of tiles, over15 mm thick rendering as screed bed in cement mortar ( 1:4 ) in floors, incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed. 29 all as per item above but area of each tile exe 0.11 sqm but n.exe 0.18 sqm, in floors & dado etc complete all as specified and directed. 30 m&l for glazed ceramic coloured / printed / dark tiles size 300x200mm x7mm thick on vertical surface in skirting / dado , set and jointed in neat cement slurry and pointed with white cement with pigment to match the colour of tiles, 10 mm thick rendering on fair faces of concrete surface ofverticle in cm ( 1:3 ) finished even and smooth without using extra cement complete, shade & design as approved by eic / ge, incl dismantling and rubbish off the primises etc all as specified and directed. 31 all as per itemabove but area tiles of size exc 0.09sqm but n.exc 0.18sqm on vertical surface in skirting / dado etc. 32 m&l for virified ceramic tiles light / dark shade 10 mm thick ( square / rectangular ) polished, area of each tiles not exc 0.36 sqm , in floors, on vertical surfaces of wall etc. set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in cm 1:6 for laying floor finishes and pointed in white or coloured cement to match and incl dismantling / demolition and rubbish off the primises etc complete all as speciefied and directed. 33 all as per item above butarea of each tiles exc 0.36 sqm butnot exc 0.42 sqm, complete all as speciefied and directed. 34 m&l for green marble 15 17 mm thick over cement screed bed laid on 15 mm thick cm 1:6 andjointed with grey cement slurry mixed with pigment ot match the shade of the slab / staircase / steps, riserincl rubbing and polishingincl moulding rounding to edge of marble & dismantling complete all as specified and directed. 35 m&l for granite 18 20mm thick ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar ( 1:6 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite incl moulding , rounding of edgeing and dismantling complete all as spd and directed. 36 s&f in repair 18 / 19 mm prelaminated particle board, prelaminated both side with decorative choice lamination & other side balancing white lamination , fixed with screws to timber / steel frame work ( incl 2 nos 100mm aluiminium handles, 1 nos 100mm hasp & staples for each shutter ) complete all as specified and directed. 37 m & l forpcc 1:3:6 type c 2 ( using 40mm agg. ) in plinth protection, path and pavingincl demolition and rubbish off the primises all as specified and directed. 38 m & l forpcc 1:2:4 type b 2 ( using 40mm graded stone aggregate ) as in flooring incl finishing the cement concrete surface even and smooth with using extra cement , rubbish off the primises and incl demolition complete all as spd & directed . 39 s&f mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing conforming to fe 290 grade e 165, complete all as specified. 40 s&f for 40mm thick flush shutters, solid core construction, with blockboard core and plywood face panels, commercial type on both sides incl taking down shutter & two coat of synthetic enamel paint over a coat of red oxide on wooden surface and cutting holes in frames of any type / walland making good dismantled portion in pcc 1:2:4 type b 1 / cement plaster 1:4 as require and make finish good to the existing surface and the followingbuilders hardware contain each shutter : ( i ) three x ms butt hinges, medium weight, cold rolled mild steel 100mm long ( isi marked ) with welded or screwed as required. ( ii ) two x aluminum anodized barrel tower bolts of extruded section 150mm long ( isi marked ) . ( iii ) two x aluminum handles cast type anodized 150mm long ( isi marked ) . ( iv ) two x aluminium alloy, anodised, sliding door bolt of 250mm long & 16mm dia with hasp, staple ( bolt type ) and fixing clips of sheet, complete all as specified and directed. 41 s&f for 110mm bore pvc pipes single socketed pressure rating @4kg / sq cmlength medium grade with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete , incl taking up / down old pipe with all fittings all as specified and directed by engineer in charge. 42 all as per item above but laid in trench or in floor complete all as specified and directed. 43 s&f for 125 / 110mm bore pvc gully trap setting / jointed with solvent cement complete all as specified and directed.. 44 s&f for 110mm bore pvc bends / junctionany radius complete all as specified and directed.. 45 m&l in repair for pvc hollow wall panelling 7 to 8mm thick any colour / design approved by engr in charge, inclusive of fixing on to wall incl moulding end caps fixed with pvc sleeves, screws as required at site & dismantling complete all as specified and directed 46 m & l for one coat of synthetic enamel paint on steel surface incl preparation of old steel surface width or girth exc 10cm all as specified and directed. 47 m&l for one coats of synthetic enamel paint on wooden surfaces of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed. 48 s&f for 2nd class hard wood glazed and skelton door shutters 35mm thick, open rebated and prepared to received glass / gauge etc ( without sash bars ) edges of framing plain, chamfered or rounded and mitred , beads for securing glass etc the size of member of shutter as specified in ssr part i clause 8.23 ( b ) and fitted to chowkahts fixed with stainless steel wire cloth 0.36mm nominal dia of wireand average width of aperture 1.40mm fixed with wire staples or wooden beads incl taking down shutter and two coat of synthetic enamel paint over a coat of red oxide on wooden surface & cutting holes in frames of any type / walland making good dismantled portion in pcc 1:2:4 typeb1 / cement plaster 1:4 as require and make finish good to the existing surface & incl the followingbuilders hardware contain each shutter : ( i ) three x ms butt hinges, cold rolled mild steel 100mm long ( isi marked ) with welded or screwed as required. ( ii ) two x aluminum anodized barrel tower bolts of extruded section 150mm long ( isi marked ) . ( iii ) two x aluminum handles cast type anodized 150mm long ( isi marked ) .complete all as specified and directed. 49 m&l for preparation of roof surface & applying evenly a tack coat of industrial bitumen 85 / 25 grade @ 1.2 kg / sqmincludingapp based polymeric membrane minimum weighing 3 kg / sqm and minimum 3 mm thick reinforced wih polyster non wove fabric ( wt not less than 150 gms / sqm ) land on primed surface by forced application, joints to be touched hot and width of overlaps not be less than 150 mmincl rendering 10mm thick in cm 1:3withwpc in sunken slab / wall complete all as specified and directed. 50 m&l, cement concrete 1:7:12 ( 40 mm graded aggregate ) in lean concrete including demolition complete all as specified and directed. 51 s & f solid pvc door frame of size 50 x 47 mm made out of 5 mm plain colour pvc sheet reinforced with ms square tube incl taking down old frame any type complete all as specified and directed. 52 s&f factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of ms tubes for top & bottom rails ms frame shall be convered with heat moulded plain colour pvc `cchannel having a pvcsheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour pvc sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour pvc sheet to be fitted in the ms frame welded / sealed to the stiles and raials with suitabale pvc sheet beading, and jointed together with solvant cement, fixing in the frame at side as per specification and drawing incl taking down old shutter complete all as specified and directed complete all as specified and directed. 53 s & f for butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 100mm, type c 21 complete all as specified and directed. 54 s&f for aluminum handles cast type anodized 100 mm long ( isi marked ) complete all as specified and directed. 55 s&f for 150mm aluminium anodised barrel tower bolts of extruded section and fixed isi marked complete all as specified and directed. 56 m&l for box type steel window 1.25 mm thick made of erw tube p section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter ( two gauged shutters and two glazed shutter ) of erw tube p section size 50 x 20 mm and 1mm thick one / two nos openable leaf consisting of two nos sash bar of t section 20x3mm welded to frame with one no vertical mullion of erw box type t section of size 60 x 25 mm and 1.25 mm thick and fi 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like handle, tower bolt, stopper, cleat, pintal hinges, hold fast etc. ( i ) hold fast, 150mm long of 120mm x 3 mm made to shape 04 nos per window. ( ii ) handle of z sec 20mm x 25mm, 100 mm long 1 no per leaf ( iii ) ms tower bolt 150mm long 2 no per leaf ( iv ) z sec 20mm x 25 mm, 100 mm long stopper 1 no per leaf ( v ) cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge 1 no per leaf. ( vi ) ms pintal hinges of size 75mm x 12mm 2 nos per leaf . ( vii ) 10 mm square guard bar, 10 cm centre to centre. ( viii ) 25x4 mm flat iron all around for joint of both frame. ( ix ) stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples& 3mm thick, sheet glass ordinary quality and glazing with oil putty . ( x ) two coat of synthetic enamel paint to ms window and guard bar. note : incl taking down old steel / wooden window and making good dismantled portion with pcc 1:2:4 type b0 incl hold fast pcc ( four no’s for each window ) & around required plaster in cm 1:4 and match with existing finishing complete all as specified and directed by engineer in charge. 57 m&l for anodised aluminium framed workfor door, window / vent ( powder coated ) aluminium section weighting 0.55kg / rm with one or more rebated incl jointed cleat for fixing etc complete all as specied and directed 58 m&l for anodised aluminium powder coated door, window and ventilator shutters, aluminium section weighting 0.55kg / rm fixed type without sash bar, incl necessary 4.8mm th sheet glass ordinary quality & glazing / black or pvc sheet joining with cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, lock , 2 nos aluminium handles 150mm, 2 x aluminium tower bolts 150mm with each shutter any type complete all as specified all as specified. 59 m&l anodized aluminium window shutter sliding type with2 track side and bottom framehaving 75 mm x 44 mm x 3 mm thick stiles bottom rail and top rail includingdouble shutters 2 nos glazed ang gauzed shutters each, necessary ftting joinery cleat glasing packing snap beading 10 mm x 10 mm , 2 nos of anodixed aluminium handle 150 mm size, including sliding rulers, 2 nos of 100 mm long alu tower bolt etc inlcuding frame of section 100 mm x 44 mm x 3 mm and including 5.00 mm thick floatglassand fixing incl taking down old ms / aluminium window complete all as specified & directed by engineer in charge.make of aluminium section hindalco / jindal 60 s&f aluminium wire guard mesh of 4mm nominal dia of wire and average width of aperture 75 85mm and fixed with aluminium frame / staples complete all as spd and directed 61 m&l for 4.8 to 5.5mm thick float glass ordinary quality, glazing or black with aluminum beeding and gasket to aluminum frameworkin squareexc 0.50 sqm ineach pane in repair complete all as specified. 62 s & ffor 12 mm thick glass door, frosted with certain logo, fixed with floor spring, fixed on floor with two nos stainless steel handle oneach leaf incl necessary provision to lock the door completed all as specified and directed. 63 s&f for pre painted galvalume aluminum zinc coating gi based corrugated / plain steel sheet 0.50mm thick of an colour profile az 150 with side lap as in roof covering / cladding to wall, ridge etcfixed with l or j hooks / self tapping screws and incldismantling of plain or corrugated steel / ac sheeting in roof covering all as specified and directed by eic. 64 all as per above item here in –before but except sheeting. 65 s / f steel work in tubular trusses and posts, vertical / horizontal bar, chin up bar and similar work including special shaped washers, chequered plates, etc complete using butt welded tubes conforming to is 1161 1979 graded st 240 with one shop coat of zinc chromate primer including dismantling of old mild steel of any description complete all as specified and directed. 66 excavating in post holes ( or similar holes ) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance not exceeding 100 mtr making goodin soft / loose soil complete all as specified and directed. 67 m&l for pcc ( 1:3:6 ) , type c 2, using 40 mm graded aggregate as foundation / mass concrete complete all as specified and directed. 68 m & l for chequered tiles of size 300 x 300 x 25 mm thick ( colour and glazed approved by eic ) with grey cement and pigments laid over 15 mm thick screed bed in cm 1:6 bedded and jointed in neat cement slurry, incl dismantling complete all as specified and directed. 69 m&l for machine pressed precast concrete interlocking paver block any shape and size confirming to is 15658 2006 of 60mm thickness, with grey cement, pigment with 25mm thick sand fillingincl dismantling and rubbish off the primises all as specified and directed. 70 all as per item above but except paver block shall be reused after necessary cleaning and making good all as specified. 71 m&l for broken bricks hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces. 72 s & f dor plain gypsum board panel 12.5mm thick on ceiling with and incl necessary gi frame used with t or any section accessories etc of galvanized steel all as per manufacturer design conforming to is 2095 and 2542 ( 1981 ) the weight of the board shall be not less than 7 kg per sqm incl dismantling of walls and ceiling board any type and two coat of obd over a coat of putty complete all as specified and directed.make.everest, gyprock.amstrong. 73 m&l for pointing to brick tiles in cm 1:3 laid flat in roofing incl racking out joints complete all as specified . 74 m&l for pcc1:3:6 type c2 as in roof pading ( average th 40mm ) ( using 12.5 mm graded aggregate ) complete all as specified and directed. 75 m & l for applying two coat of undiluted thick coat of acrlic reinforcement liquid applied elastorneric water proofing membrane with uv resistance properties and solar refective properties over one coat of primer ( 1:3, dilution:water ) note: every each coat gap between 6 hrs ) complete all as specified and directed.make : asian paint, sika, fosroc 76 s & f in repairfor viterous china squating pan of ( orrissa pattern ) size 580 mm white with p or s trap front or back inlet and integral foot rest ( excluding flushing cisteern and flush pipe ) fixed inclcement concrete bedding as required set complete all as specified and directed. 77 s & f in repair for viterous china wash down water closet pan ( pedestal pattern ) coloured includingp or s trap with flush pipe of chromium plated brass 32 mm dia for low levelflushing cistern incl plastic seat cover white closed pattern with float bottom and cover and jet connection and mild steel chrominum plate or aluminized hanging device fixed in repairs complete all as specified and directed. 78 s & f in repair for viterous china wash hand basin white flat back size 550 x 400 mm with leg incl cp waste coupling, waste pipe & plug and porclain stopper brackets and cutting for and pinning in ends of brackets or erceting stand fixed complete all as specified and directed. 79 s & f in repairvitreous china ware over counter ovel wash hand basin, any colour, size 570 x 450 mm sizeincluding cutting for and pinning ends of brackets or erecting stand including fixing waste pipe , cp waste coupling & bottle trap all as specified and approved by enger in charge. 80 s&f in repair 10 ltr capacity low levels flushing cistern with pvc bend and pvc flush down pipe etc complete all as specified and directed. ( make : parryware / hindware ) 81 s & f in repair bib tap cp fancy type / long body15 mm bore with will crutch or buttewrfly handle screwed down screwed to iron pipe complete with all fittings all as specified and directed. 82 s & f in repair angle cockcp fancy type 15 mm bore screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for unions complete all as specified and directed. 83 s & f in repair stop cock concealed long shank chromium plated fancy type 15 mm borescrewed down high pressure with crutch or butter fly handle complete all as specified and directed. 84 s& f for in repair swan neck pillar cock chromium plated fancy type screw with iron pipe incl all fittings complete all as specified and directed . 85 s&f in repair hole washbasin mixer wround spoutwith 375 mm long braided hosescomplete all as spd and directed. 86 s & f in repairwall mixer 15 mm bore ( fancy type ) cast copper alloy with capstan head, cp screwed down high pressure with long screwed both ends for iron pipe as per union complete all as specified and directed. 87 s& f for looking mirror of best size ( 600 x 450 ) mm bevelled edged mirror of selected quality glass mounted on 6mm th ac building board, aluminium channel around fixed with provision of hanging hooks complete all as specified and directed. 88 s&f in repair for door closer hydrulicacally, alluminium regulated designation no 1 universal type suitable for door shutter complete all as specified and directed. 89 s&f for pvc connections 45cm long superior quality with ptmt nut on both sidecomplete all as specified and directed. 90 s&f for 100mm bore cast iron soil, waste and vent pipes, in any lengthwith or without ears, with cement joints, fixed to walls etcincl taking down old pipe complete all as specifed and dirtected. 91 s&f for 100mm bore ci bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) 92 m&l for taking down rolling shutter size exc 5 sqm but n. 16 sqm and refixing in position after necessary repair to welding work, repair / replacement of ball bearing chain wheels, anchor rod , gear box etc incl greasing & easing of rolling shutter and applying a coat of synthetic enamel paint on steel surfaces complete all as specified and directed. 93 ditto all as per item above but shutter size exc 16 sqm but n. exc 28 sqm complete all as specified and directed. 94 m & l for providing pre cast cement concreate louvers and jallers 40m thick set in cement motor 1:4 of type b1:2:4 ( 12.5mm graded stone aggrigate ) measured solid all mounding but including frame, taking down etc coplete all as speified and directed. 95 m & l for providing pre cast cement concreate ( rcc jali piller ) size of piller 100x100x700mm and taking down compleateall as speified and directed. 96 s&f inrepair 300mm ms rat tail road ordinery pattern spring including roller and roller plate complete all as specified and directed. 97 s&f in repair floor door stoper of aluminum with hand down steel spring fixed in floors overall length of cover plate 140mm compleate 98 taking down of old gate, area n exc 15 sqm and erection and refixing the same aftermaking it serviceable, easing, renewing and greasing, oiling complete including cutting, filling for hold fast incl making good in pcc 1:2:4, type b 0 as required, including one coat of synthetic enamel paint to ms gate as required complete all as specified and directed. 99 m&l machine cut kota stone of size 45 x 60cm or 60 x 60cm, mirror polished ( selected quality ) slab flooring 20 to 25 mm thicklaid in slope and jointed with grey cement slurry mixed with pigment to match the shade of slab, over and including screed bed of 20mm thick in cm 1:4, complete, all as specified and as directed by engr in charge. 100 m&l for forming 12mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound, grade b in on concrete slab all as specified and directed. 101 taking down carefully the existing aluminium / copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets, ceiling rose, regulators and light fittings any type etcby unscrewing and taken away from site complete.note :cost of unserviceable materials will be charged from the contractor against schedule of credit. 102 m & l for point wiring for one light point / bell / fan point controlled by one switchcomplete with 1.5 sqmm single core pvc insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to is specifications, drawn through and including conceled conduitconcealed / fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm ms sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm pvc insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly all as specified and as directed : 103 all as per item no 101 here in before but with one 3 pin 5 amps switch socket on independent board. 104 all as per item no 101 here in before but withone 3 pin 5 amps switch socket on same board. 105 all as per item no 101 here in before but with cable 2.5 sqmm ( nominal area ) multistranded copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continous earth wirte pvc insulated 2.5 sqmm copper multistranded conductor connecting to common earth and earth dolly complete all as specified and directed 106 supply and fix switch piano one way 5 a, sp, 230 volts. 107 supply and fix ofswitch 16 amps flush type. 108 supply and fixing of socket outlet two in one, 3 pin each suitable for 5amperes flush type, 230 volts ac complete all as specified and directed. 109 supply and fixing of socket outlet two in one, 3 pin each suitable for 15amperes flush type, 230 volts ac complete all as specified and directed. 110 supply and fix stepped type electronic fan regulator flush type all as specified and directed. 111 supply and fixing ceiling rose surface bakelite3 terminals 65x32mm complete all as specified 112 s&f lamp holder, pvc / polycarbonate type with cord grip cap suitable for pendant / batten fittings including led bulb 9 watt, 230 volt complete all as specified and directed 113 s&f distribution boarddouble doormade out of crca mild steel sheet surface with insulated material like polyester or with epoxy powder coating and ip 43 & ik 09 protection surface mounting spn 12 way, 240 volts with bus bar rating 200 amps, dust and vermin proof suitable for incorporation of mcb’s and isolators etc complete all as specified. make :legrand / hager / schneider elect . ( note : cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash / colour / distemper etc is included in quated rate ) 114 supply and fixing in replacement of led t 8 tube light fitting with single side connection polycarbonateled tube rod 18 / 20 / 22w 4 feet with crca box suitable box complete including rotary type bipin holder and connection with pvc insulalted twin core 23 / 0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed. make : wipro cat part no for ftl wi0922208p , tube light ll13 181 65se , havells cat part no for ftl 1 x 22 / 20 wssbswh tube light sstl20wled865spc, crompton cat part no ftl1gp131lt8 16 tube light ltt8 20 & orient cat part no libt 188 55 rated power ( 01 x 18 / 20wt 8 led tube ) note: led box and led channel should be of same make 115 m & l for sub main wiring with pvc insulated, 1100 volts grade single core multistranded copper conductor cable conforming to is specifications, 2 runs of 6sqmm including 1 run of 6 sq mmsingle core multistranded copper conductor, pvc insulated cables as earth continuity conductor drawn through and including one run of 25 mm dia rigid pvc conduit and conduit accessories fixed on wall / ceiling etc., or concealed in wall and connecting to common earth dolly all as specified and directed including taking down all sub main wiring . make of frls wire; polycab / havells / rr cable, make of pvc pipe polycab / finolex / kalinga premium. note :2 run of 6 sqmm, 1 run of 6 sq mm and 1 run of pvc conduit will bemesuared as 1 unit. 116 s&f distribution boarddouble doormade out of crca mild steel sheet surface with insulated material like polyester or with epoxy powder coating and ip 43 & ik 09 protection surface mounting spn 8 way, 240 volts with bus bar rating 200 amps, dust and vermin proof suitable for incorporation of mcb’s and isolators etc complete all as specified. . ( note : cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash / colour / distemper etc is included in quated rate ) 117 s & fin repair mcb spn, 240 volts, 40 to 63 ampere, rupturing capacity 10 ka, ‘b’ curve type complete all as specified and directed.make :legrand / hager / schneider elect 118 s & f in repairmcb single pole, 240 volts, 6 to 32 ampere, rupturing capacity 10 ka, ‘b’ curve type complete all as specified and directed. make :legrand / hager / schneider elect 119 s & f in repairmcb single pole, 240 volts, 40 to 63 ampere, rupturing capacity 10 ka, ‘b’ curve type complete all as specified and directed. make :legrand / hager / schneider elect 120 earthing complete with gi earth plate electrode of size 60 x 60 x 0.6 cms burried directly in ground vertically at a depth of not less than 2.25 mtrs below normal ground level with top edge of the earth plate at a depth not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cms thick and packed layer of charcoal dust and common salt filling in alter nate layers etc and connected to and including gi earth striq size 25x4mm upto 7.5 mtr by means of bolts, nuts, checknuts and washers made out of galvanised iron and protected by light grade 15 mm dia 5 mtr long and connected to main control panel and gi pipe 20 mm medium grade as watering pipe including funnel, wire mesh, pcc pit made up of pcc 1:2:4 type c2 and rcc cover 40 mm thick with 8 mm bar 15 c / c including excavation and earth work all as specified in ssr part 1 2009. 121 m&l forroad cutting including excavation and gettingout, returing fittlinginspreading levelling and well rammingin layers, soling with broker builders or quarried stone, inter stices filled, 7.5 cm thick ( compacted thickness ) wbm ( water bound macadam ) with coarse aggregateretreived from road cutting consolidated to required gradientand camber, including applying evenly a priming / tack coat with bituminous primerand making surface even and getting our surplus soil complete all as specified and directed. 122 supply and fixing / laying galvanised pipe 50 mm bore medium grade fixed to pole with clamps nuts, bolts and washers or laid under road crossing or fixed to wall complete all as specified and directed. 123 supply and fix in replacement of security light fitting led 25 watt aluminum pressure dia cast housing with touched glass cover ip 66 protectionincludingsuitable sizeand accessories complete mounted including connection with 3 core pvc insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal including taking down old cfl security light fittingall as specified and as directed. 124 s& f gi bracket light grade gi pipe 1.2 mtr length of suitable dia for fixing of street light fitting25 / 35 wattincluding connection all as specified and directed. 125 s&f mccb incomer distribution board double door vertical type made out of crca ms sheet surface with insulated material like polyester or with epoxy powder coating surface mounting tpn 4 way, 415 volts with copper bus bar rating 200 amps, dust and vermin proof suitable for incorporation of mccb and ip 43 ik 09protection with and incl 100 amp 36 ka 4 pole mccb with thermal magnetic setting and icu = ics = 100% ) complete all as specified. . ( note : the cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash / colour / distemper etc is included in quated rate ) 126 m & l for laying of lt cable of 1100 volt xlpe insulated and pvc sheathed of size 25 sqmm 4core with cable gland including taking down oldunserviceble cable complete all as specified and directed by engineer in charge.make havells, glostar & polycab. 127 excavation in trenches in any type of soil n.exc. 1.5 mtr wide and n.exc1.5 mtr in depthall as specified & directed. 128 returning, filling in, any type of soil and spreading in layers n. exc 25cm thick each layer including watering & well ramming complete all as specified& directed. 129 removal of surplus soil to a distance n.exc 50 mtr & depositing where directed at a level n. exc. 1.5mtr above the starting point complete all as specified & directed. 130 supply, laying & fixing double wall corrugated ( dwc ) pipes made of high density polyethylene ( hdpe ) with all accessories i.e. all type of joints, sockets, elbows, bends and end cap etc. of size 75 mm outer dia and 61 mm inner dia complete all as specified and directed. make : telerex / tirupati or e in c approved make 131 taking down ceiling fan of any make & sweep size by disconnecting clips, lock nuts etc. from existing position of any height, keeping in safe costudy and hanging the same after cleaning andpainting of ceiling fan complete with synthetic enamel paint by spraying one coat and marking mes no. complete all as specified and directed by engr in charge. 132 supply & fixing in replacement ofamaze square / round recess mounteddown lighter12 watt including separate replaceable electronic driver celling cut out 106mm x 106mm height 33mm square shaped polycarbonate fixturecomplete all as specified and directed. 133 supply and fixing led luminaire 600 mm x 600 mm, 35 / 36 watt, 220 v ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable sizecomplete. 134 supply & fixing in replacement ofamaze square / round recess mounteddown lighter15 watt including separate replaceable electronic driver celling cut out 106mm x 106mm height 33mm square shaped polycarbonate fixturecomplete all as specified and directed. 135 supply and fixing ofexhaust fan of sweep 230 mm complete with self closinglouvers, mounted in suitable opening arrangement and suitable for operation on 230 volts single phase, 50 hz, ac supplyand including two core pvc insulated, pvc sheathed copper conductor flexible cable 1.5 sqmm and making all necessary connection and fixed by using 4 nos 100 mm long 10 mm dia bolts, nuts and washers and grouted in wall in wall with cement1:3 completed all as specified and directed. make: havells / cg / orient.note: the cost of making hole in the existing wall and making good the disturbed surface of wall / ceiling etc as original i.e. brick work, plastering, white washing ect. is included in the quoated rate and no extra payment will be made to contractor in this effect. 136 single pole and neutral enclosure 32 a , 230 v with a two pin and earthplug and socket complete with one singlepole mcb 25 a complete all as specified and directed....

Military Engineer Services - Punjab

35302188 upgradation and extension of baffle range at nams ( tender id : 2022_mes_550653_2 ) surface dressing not exceeding 15 cm deep in soft / loose soil completeall as specified & directed. 3 earth work in excavation in all kind of soil by mechanical means ( hydraulic excavator ) over areas ( exceeding 30cm in depth, 1.50 metre in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 metre and lift upto 1.50 metre complete all as specified and directed. 4 all as per srl item no 1.02 above but depth exceeding 1.50 metre and not exceeding 3.00 metre. 5 earth work in excavation by mechanical means ( hydraulic excavator ) / in trenches or drains ( not exceeding 1.5 metre in width or 10 sqm on plan ) , not exceeding 1.5 metre deep including dressing of sides and ramming of bottoms, lift upto 1.5 metre, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metre complete all as specified and directed. 6 all as per srl item no 1.04above but depth exceeding 1.50 metre and not exceeding 3.00 metre. 7 excavating in trenches in soft / loose soil not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth for foundation for pipes, wells, cesspits, manholes, pier holes, cables etc not exceeding 10 sqm on plan and not exceeding 1.50 metre in depth and getting out complete all as specified and directed. 8 all as per srl item no 1.06above but depth exceeding 1.50 metre and not exceeding 3.00 metre. 9 surface excavation not exceeding 30 cm deep and averaging 15 cm deep, getting out in any type of soil complete all as specified and directed. 10 material and labour for approved earth filling in floors / trenches, laid in layers not exceeding 15cm thick spread, levelled and rammed / rolled including watering to required level & gradient complete all as specified and as directed. note : quoted rate shall deemed to be inclusive of supply of earth from outside defence land. 11 returning, filling in, spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each complete all as specified and directed. 12 material and labourfor cement concrete 1:4:8 type d 2 using 40mm gradedstone aggregate as in foundation filling anf mass concrete complete all as specified and directed. 13 material and labour for rcc ( m 25 ) design mixusing 20 mm graded stone aggregate as in foundation including rafts, footings and mass concrete etc complete all as specified andas directed. 14 material and labour for rcctype m 25 ( design mix ) using 20 mm graded stone aggregate in beam, lintels over 1.5m span height for staging upto 9.5m from gl complete all as specified andas directed. 15 material and labour for rcctype m 25 ( design mix ) using 20 mm graded stone aggregate in columns, pillars, posts height for staging upto 9.5m from gl etc complete all as specified andas directed. 16 use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces of concrete, flat, complete all as specified and directed. 17 use and waste of formwork to the sides of pillars, posts, piers, columns and stanchions, square or recatngular or polygonal, rough finished surface of concrete height for staging upto 9.5m from gl complete all as specified. 18 use and waste of form work to sides and soffits of floor or roof beam lintel beam, flat surfaces, support overhanged rough finished surface of concreteheight for staging upto 9.5m from gl complete all as specified and directed. 19 material and labour for mild steel tmtbars 10 mm dia and over, cut to length, ent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed 20 material and labourmild steel reinforcement tmtbars 5 mm dia and over up to and including 10 mm dia. in stirrups, spacers, binders etc.cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 21 m & l for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth not otherwise described for and priming with red oxide primer and applying two coat of synthetic enamel paint over priming coat all as specified and directed. 22 material and labour for rcc m 25 design mix, using 20 mm graded aggregates in walls, retaining walls, basement walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed. 23 material and labour 20mm thick cement plaster 1:4 mixed with recron fibre @ 180gm / bag of cement or as per manufacturer instruction s ( rough finish ) . note: recron fibre will be measured & paid for separately under relevant item here in after. 24 supply only recron fibre complete all as specified and directed. ( recron fibre shall be is marked & shall be approved by ge. 25 removal of excavated spoilto a distanceexceeding 500 metre but not exceeding 1.5 km and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed. 26 supply only 80mm thick bullet resistant fics panel ( slurry infiltrated fibre concrete ) of size 2.0 metre x 1.0 metre ( in three parts as shown on drgs ) ( 0.7m+0.6m+0.7m ) in lining on firing face of baffle wall all as per tbrl design and specifications and baffle range manual ( as amended up to date ) all as per shown in drg.note: ( i ) only tbrl certified makes panels shall be used in work. ( ii ) testing of panel shall all be carried out all as specified in particular specification section ii 27 fixing only of fics panels on baffle wall using 02 nos of hardwood battens of size 2000mmx100mmx35mm at the back of panel and using 06 nos of trutek or equivalent m 20 bolts and nuts of min 300mm length and 30 / 32mm dia / bore galvanised steel sleeve medium grade alongwith hardwood cap as per requirement at site complete all as specified and as shown on drgs. 28 fixing only of fics panels on baffle wall using 02 nos of hardwood battens of size 2000mmx100mmx35mm at the back of panel and using 06 nos of trutek or equivalent m 20 bolts and nuts of min 675mm lengthwith hardwood cap over the exposed faces of bolts of size 100x100mm in existing sleeve complete all as specified and directed by engr in charge. note for item no. 1.26 & 1.27: any other items required for fixing of fics panels shall also be deemed to be included in the quoted rates & nothing extra shall be admissible. 29 material and labour for 30mm thick cement palster 1:3 mixed with recron fibre @ 180gm / bag of cement or manufacturers instructions as specified ( rough finished ) . note: recron fibre shall be measured & paid for separately under relevant items here in before. 30 material & labour for reinforced cement concrete type m 25 design mix using 20 mm graded stone aggregatein stair case including steps complete all as specified andas directed. 31 use and waste of formwork to faces of walls, retaining walls, abutments, parapets & staircase railings and similar work including attached pilasters, buttresses etc vertical or to fair finished complete all as specified and as directed. 32 supply and fixing 2nd class hard wood boarding 30mm thick clean sawn with butt joints with nails is any situation ( except flooring and skirting ) complete all as specified and directed. 33 material and labour for cement plaster 15mm thick on fair faces or other than fair faces of brick work in cement mortar ( 1:4 ) finished even and smooth without using extra cement complete all as specified and as directed 34 material and labour for preparation of newly plastered surface on wall and applying two coats of apexpaint over a coat of alkali resistant primer at a height not exceeding 13m above or below gl in camouflaging pattern complete all as specified and directed. 35 material and labour 200 mm bore dia rcc pipes class np2 complete with collars laid in trenches and testing complete all as specified and directed 36 material and labour for plain cement concrete ( 1:3:6 ) type c 2 using 40mm graded stone aggregate as in bed of 200mm dia rcc pipes including forming cradles after they are laid & tested complete all as specified. 37 material and labour for preparation of new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified. 38 m&l for rcc ( m 25 ) design mix as using 20 mm as in slab supported on walls, beams and columns in floors, roofs, landings, balcony, canopy, deck slab and in shelves and the like complete all as specified andas directed. 39 use and waste of form work to sides and soffits of suspended slabs such as roof slab, landing and similar work complete all as specifed and directed. 40 use and waste of form work to edges of slabs such as roof slab, landing and similar work complete all as specifed and directed. 41 material and laying mild steel frame work as in manhole cover and in hold fast complete welded, hinged or pinned confirming o fe 290 gde e 165 complete all as specified. 42 material and labour for mild steel round deformedbars 16 mm dia and over, cut to length, ent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 09.mm dia or securing with clips complete all as specified and directed 43 material and labour for precast reinforced cement concrete 1:2:4 type b 1 using 20mm graded stone aggregate as in manhole cover and set in cement mortar 1:4 complete all as specified. 44 supply only composite trapezoidal boxes for ground barriers of size 1000mm x ( 700mm front& 650mm back ) x200mm thick all as per details shown on drawings. 45 all as per srl item no 1.43 above but of size 900mmx ( 700mm front and 650mm back ) x200mm thick complete all as per details shown on drawings. note for item no. 1.43 & 1.44: earth filling, stone aggregate & pcc 1:3:6 type c 2 shall be measured & paid for separately under relevant items. 46 material and labour for plain cement concrete 1:3:6 type c 2 using 40mm graded stone aggregate in foundation for fixing of ground barrier boxes complete all as specified. 47 supply and filling graded coarse aggregates of nominal size 10 20mm, for ground barrier boxes including filling all as direced by engr in charge. 48 demolition of cement concrete ( unreinforced ) in ground floors and paving not exceeding 15cm thick ( below or above ground level ) complete all as specified and directed. 49 material and labour for 75mm thick cement concrete 1:2:4 type b 1 using 20mm graded stone aggregate as in sub base of flooring finishing surfaces finished the surface even and smooth without using extra cement complete all as specified and directed. 50 material and labour brick work with fly ash bricks straight or curved on plan exceeding 6.00 mtr mean radius in cement mortar 1:4 including corbelling etc including demolition of old brick work complete all as specified and directed 51 taking down cement plaster from walls / ceilling including raking outjoints, hacking for key scrubbing down with water and dispose off debris upto distance not exceeding 500 m where directed complete all as specified and as directed. 52 supply and fixing ms wire mesh of size 40mmx40mm aperture hole with thickness 2 to 3mm and welding to existing reinforcement in wall / ceiling ( minimum 40 pieces in one sqm ) including necessary fixing arragement like scaffolding, welding machining etc complete all as specifed and as directed. 53 taking down bullet resistant sifcon panel of any thickness size and in any position on baffle wall etc complete all as directed. 54 dismantling off framed work timber scantling 40 sqcm and over in section & in any position completeall as specified. 55 dismantling of reinforced cement concrete of any description & in any position at any depth above or below gl completeall as specified and direced by engr in charge. 56 material and labour for plain cement concrete ( 1:2:4 ) type b 1 using 20mm graded stone aggregate cast in situ in lintels upto 1.5m span, cills and other similar bands, parapets, copings bed plates & like including weathering etc complete allas specified. 57 dismantling structural steel work including members by cutting rivets, removing nuts & bolts complete all as specified and as directed. 58 supply and fixing mild steel work as in framed work such as targets, grills, grating, framed guard bars etc with ends of bars shouldered or rivetted or forged into spikes and similar work conforming to fe 290 gde e 165 complete all as specified and as directed by engr in chrage. 59 supply and fixing in repairs 16mm dia hard drawn twisted steel wire rope fixed in any position including necessary cutting, notching and bolting arrangement complete all as specified and as directed. 60 supply and cast iron work grade fg 150 machined, in pulleys and similar article weight not execeeding 5 kg each complete all as specified. 61 supply and fixing 2nd class hard wood boarding 15mm thick clean sawn with butt joints with nails fixed over ms frame as targets in any situation ( except flooring and skirting ) complete all as specified and directed. 62 supply & fixingmild steel screw bolts ( machine made ) 11 to 15mm dia of shank with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc. 5 but not exc. 10 cm long, complete all as specified and as directed. 63 material and labour for 25mm thick cement concrete 1:2:4 type b 1 using 20 mm graded stone aggergate as in floors or steps and treads finishing cement concrete surface ever and smooth with using extra cement complete all as specified. 64 dismantling of heavy armoured plate of mild steel work of any description fixed with nuts & bolts over stop butt complete all as specified & as directed by engr in charge. 65 fixing only heavy armoured plate of any description with nuts & bolts over stop butt complete all as specified. note: nuts & bolts to be measured & paid separtely under item no 1.61 & 1.76. 66 material for labour 2nd class hard wood wrought in scantlings and fixed in repairs to replace old and decayed timber ( including piecing scarfing etc of old and new timbers if required ) in any shape & place complete all as specified and directed. 67 supply and fixing 25mm thick second class hard wood planks fixed over stop butt with nails, screws etc complete all as specified and as directed. 68 material & labour for earth filling under stop butt approved by ge, earth shall be free from vegetation, aggregate & shall be dry in powder form and filling in embankement complete all as directed by engr in charge.note : quoted rate shall deemed to be inclusive of supply of earth from outside defence land. 69 material & labour for roughening old concrete surfaces of wall / ceiling surfaces by picking, tucking with chiseling, sweeping clean and washing down with water to remove dust etc for baffle wall / side wall / stop butt complete all as specified and directed by engr in charge. 70 supply and fixing ms mesh of mesh of size 25mm and 1.4mm dia wire welding to existing reinforcement in wall / ceiling including necessary fixing arrangement like scaffolding welding machine etc complete all as specified and as directed. 71 material & labour washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 ( 1 cement : 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per sqm, top layer 15mm cement plaser 1:1 / 2:2 ( 1 cement:1 / 2 coarse sand: 2 stone chipping 10mm nominal size ) in panels withgroove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified. 72 material and labour for preparing old plastered surfaces of wall and applying one coat of apex paint at height not exceeding 10mtr from gl in camouflaging pattern over a coat of alkali resistant primer complete all as directed. 73 material and labour brick work with sub class b brick straight or curved on plan to any radius in half brick thick built in cm 1:4 complete all as specified and directed 74 material and labour brick work with sub class b brick straight or curved on plan exceeding 6m mean radiusbuilt in cm 1:6 complete all as specified and directed 75 material and labour for flush pointing to bricks walls in cement mortor 1:3 complete all as directed by engr in charage. 76 extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds stopped ends etc complete all as specified and directed. 77 supply and fixing mild screw botls ( machine made ) 16 to 20mm dia of shank with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc. 22.5 cm but n. exc 30 cm long, complete all as specified and as directed. 78 e / m works 79 material and laying for sub b bricks ( old size ) for cable protection laid flat and dry intrenches over the cable perpendicular to the direction of cable complete all as specified in ssr and directed by engr in charge. 80 mateiral & labour sand cushioning with dry and clean sand in two layers first layers of 80mm thick before laying of cables and second layer of 150mm after laying of cable complete all as specified and directed by engr in charge. note: punned down thickness shall be measured for payment. 81 supply and laying in replacement of lt underground cable xlpe insulated, inner pvc sheathed, galvanized steel strip armoured, pvc sheathed electric power cable with stranded compact aluminium conductor 1100 volts grade 35sqmm 3.5 core suitable for earthed system laid in duct / trench / along pole etc including making connection. note: the cost of aluminium timbles / lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it. 82 all as per srl item no. 2.03 here in after but of size 25 sqmm 4 core 83 all as per srl item no. 2.03 here in after but of size 10 sqmm 2 core 84 supply and fixing in replacement street light fitting bracketmade out of galvanised iron pipe 40mm bore light grade 1.5 mtr long complete with nuts, bolts, washer clamp etc all as specified and directed by engr in charge. 85 supply and fixing in replacement galvanized iron pipe of 50mm bore light grade fixed to poles / walls with nuts, bolts and washers or laid under road crossing complete all as specified and directed. 86 material and labour fabricating and fixing in replacement cross arms ( any type ) supports, bracing, stiffners etc made out of ms channel, angle iron, flat iron of any size including drilling of holes, making clamps, eye hooks, nuts, bolts and washers etc, welding if required including painting with two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed. 87 supply and fixing in replacement pin / disc type procelain vitreous white, brown or green insulator including one galvanized mild steel straps, washers and nuts for 1100 volts grade, including removal of existing insulators complete all as specified and directed. 88 material and labour in replacement for acsr conductor any size drawn straight horizontal lt over head lines on existing poles including binding with insulators, weight of conductor shall be measured straight horizontal distance between centre of two adjacent ht / lt poles and calculating weight of conductor or size length by adding 3% extra for sag, jointing jumpers etc complete all as specified and directed. 89 supply and fixing led street light fitting ip 66 pressure dia cast aluminium housing ( heat sink ) for effective thermal management, sturdiness excellent corrosion resistant ip operating voltage 140 270 volts, pf ( 0.95 ) , assemetric lens of leds, luminous flux>3800lm, efficacy of led>130 lm / w, of luminaires 60 watt led 5700k including fitting, lamp etc complete all as specified and directed. 90 supply and fixing in replacement lt feeder pillar box 440 volts 3 phase 4 wire 50 hz out door weather proof ip 56 ( cpri approved ) made out of 3mm thick crca sheet and angle iron frame made out of 50x50x6mm both side opening and suitable to fix cable glands locking arrangements powder coated and panel embarked in pcc block 30x30x60cm fixing in ground with suitable size of nut bolts and comprising of the following: ( a ) aluminium bus bar of capacity 200 amps 1 set of 4 ( ryb & black duly insulated ) ( b ) mccb 100 amps, 16 ka with adjustable thermal and fixed magnetic type ics 100% 01 no. ( c ) mcb tpn 63 amp, 10ka, 415v 02 nos ( d ) automatic quatrz time switch 3 phase 02 nos ( e ) digital amp meter of capacity 0 to 200 amp with selector switch=01 no ( f ) digital volt meter of capacity 0 to 500 volt 01 no. ( g ) led indicator lamp set of three. 91 supply and errecting prestressed concrete pole 9.0 mtrs long, 120x172mm at top and 102mm x 279mm at bottom class 10 complete with painting on poles all as specified and as directed by engr in charge. 92 material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick, buried directly in ground ( earth pit not less than 2.25 metres deep below ground level ) with top edge of the plate not less than 1.50 metres below normal ground level, earth plate surrounded from all sides by 15cm thick packed layers of charcoal dust and common salt filling in alternate layers alround, top & bottom and electrode connection by using galvanized iron earth strip 25x4mm connected to earth plate electrode by means of bolts, nuts check nuts and washers made of galvanized iron or steel and thimbles, gi pipe light grade 20mm bore for watering with funnel and wire mesh, gi medium grade 40mm bore protection pipe for drawing in earth lead wire, pcc chamber in pcc 1:2:4, type b 1 with angle iron 25x25x3mm frame work and pre cast rcc cover in rcc 1:2:4, type b 1, cover reinforced with 8mm dia tmt bars @100mm c / c both ways and 12mm dia ms fabricated handle, test point complete all as shown in electrical plate no 3 of mes standard schedule of rates ( part i ) including necessary excavation and earth work in any type of soil, returning filling and removal of soil to a distance not exc 50 metres and testing on completion complete all as specified and directed.notes ( a ) the unit rate shall include for gi protection pipe, gi watering pipe, wire mesh, funnel and excavation, rcc pit cover, test point, galvanised iron strip from top of earth plate upto 5.0 metres above ground level and if gi protection pipe is less than 5.0 metres, no price adjustment shall be made. ( b ) pccpit shall be provided at least 50cm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junction, elbow etc shall be deemed to be included in the unit rate. ( c ) if the testing result of earthingwork is not found satisfactory then the contractor shall do another earthing work at his own cost and nothing shall be permissible on this account. ( d ) earthing work will be carried out in presence of mes representative....

Baba Farid University Of Helath Sciences - Punjab

34603908 supply and installation of physiotherapy modalities/equipments for ucop, fdk , supply and installation of physitherapy equipments (specifications for pharmacy equipments as per tender document) , cpm for lower limb , swd 500 watts , hydrocollator packs , infrared bulb , tens wire , ms wire , 4 channel tens , ultrasound therapy 1mhz , paraffin wax , heel exerciser , ankle exerciser , ms electrodes , tens electrodes , treadmill commercial , massager...

Baba Farid University Of Helath Sciences - Punjab

32773429 tender for supply and installation of phsiotherpay equipments for ucop, fdk , supply and installation of physitherapy equipments ( specifications for pharmacy equipments as per tender document ) , cpm for lower limb , swd 500 watts , hydrocollator packs , infrared bulb , tens wire , ms wire , 4 channel tens , ultrasound therapy 1mhz , paraffin wax , traction machine , heel exerciser , ankle exerciser , ms electrodes , tens electrodes , treadmill commercial , massager...

Hindustan Insecticides Limited - Punjab

32007861 providing and fixing of steel gate in front of rolling shutter in spp and structural steel work, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (fabrication and erection of four panelled gate 2.5m x 2.9m with isa 40x40 for frame and ms flats,ms wire mesh with required aldrops, tower bolts locking arrangement)...

Military Engineer Services - Punjab

27089714 provision of bazaar supply items at af stn bhisiana 1 coarsed stone aggregate 12.5mm grade locally best available from approved quaries. 2 coarsed stone aggregate 20mm grade locally best available from approved quaries. 3 fine aggregate ( sand ) locally best available from apoved quories. 4 portland cement grade 43 50 kgs bag. make jk / ultratech / acc / shree cement / ambuja or equilvent. 5 white portland cement in in polyethelyne bags or other packing. make jk birla white or equilvent. 6 sub class bricks of standard size locally best available from approved furnaces. 7 200 mm ordinary rat tail rod pattern door springs with roller and roller plate. 8 mortice lock 2 levers vertical type size 100 mm. make: link / godrej or equivalent. 9 cup board locks brass with 2 levers make : link / godrej or equivalent. 10 brass polished cuboard knobs fixed with nut, screw and washer. make as per sample kept in ge office. 11 floor door stoper aluminium alloy body with hard drawn steel spring double leg. make as per sample kept in ge office. 12 stainless steel wiremesh, 0.56 mm nominal dia of wire and average width if apreture 1.4mm. make agtha / elephant or equilvent nnote : wiremesh roll should be 1.2 mtr wide to avoid wastage. 13 galvanised iron ms wire cloth, 0.63 mm nominal dia of wire and average width of apreture 1.4 mm. make agtha / elephant or equilvent. nnote wiremesh roll should be 1.2 mtr wide to avoid wastage. 14 0.56 mm plain aluminium sheet. 15 plywood grade bwp type bb 6 mm thick, commercial facing size 8x4 make centuary / kitply / greenply / mysorechip board. 16 plywood grade bwp type bb 4 mm thick, commercial facing 8x4. nmake centuary / kitply / greenply / mysorechip board 17 aluminium standard door bottom seal with nylon brush at lower side to fit at the bottom of door shutter upto 1.1m length. make as per sample kept in ge office. 18 flexible rubber 5 mm th 50 mm wide for door bottom seal. make as per sample kept in ge office. 19 neoprene beading for aluminium windows / doors glass fixing. make as per sample kept in ge office. 20 aluminium butt hinges 100 size. make: crown, classic, argent , isi marked. 21 aluminium butt hinges 75 size. make: crown, classic, argent , isi marked. 22 aluminium sliding door bolt 300 mm along with locking plate. make : crown, classic, argent , isi marked. 23 aluminium sliding door bolt 250 mm along with locking plate. make: crown, classic, argent , isi marked. 24 mild steel wire nails with head for wiremesh ( black ) size n.exc 20mm. make as per sample kept in ge office. 25 mild steel wire nails with head for wiremesh door bidding, fixing of plywood and size not exc 25mm ( 17 nos ) . make as per sample kept in ge office. 26 mild steel wire nails with head for door repairs size not exc 50mm ( 12 nos ) . make as per sample kept in ge office. 27 mild steel wire nails with head for size not exc 25mm ( 14 nos ) . make as per sample kept in ge office. 28 mild steel wire nails with head for size not exc 50mm ( 10 nos ) . make as per sample kept in ge office. 29 mild steel wire nails with head for size not exc 100mm ( 8 nos ) . make as per sample kept in ge office. 30 mild steel wire nails with head for size not exc 100mm ( 10 nos ) . make as per sample kept in ge office. 31 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 75x10. make as per sample kept in ge office. 32 mild steel machine screws, bright finished, with slotted countersunk head, full length threaded n.exc 50mm ( black ) . make as per sample kept in ge office. 33 mild steel full length threaded screws for iron window size n.exc 15mm. make as per sample kept in ge office. 34 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 30x7. make as per sample kept in ge offce. 35 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 35x8. make as per sample kept in ge office. 36 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 19x10. make as per sample kept in ge office. 37 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded size 19x8. make as per sample kept in ge office. 38 25mm wide pvc lipping for cupboard and inbuild furnitures. 39 brass spimndle for concealed stop cocks for 15mm dia ( half turn ) as per sample kept in ge office. 40 brass spindle for piller cock for 15mm dia ( half turn ) as per sample kept in ge office. 41 brass spindle for stop cocks for 15mm dia ( half turn ) as per sample kept in ge office. 42 brass spindle for bib cocks for 15mm dia ( half turn ) as per sample kept in ge office. 43 15 mm dia long body cp bib tap make : hindware, cera, parryware, gem, prayag. 44 15 mm two way cp angle cock. make: hindware, cera, parryware or equivalent. 45 flexible telephonic pipe for health faucets and hand shovers length 1.2 mtr. make: hindware, cera, parryware, gem, prayag. 46 cp shower rose ( cicular or square shape 125 mm dia ) with pivot and arm. make : hindware, cera, parryware, gem, prayag. 47 syphon set ( internal kit ) for flush tanks. make : prayag , hindustan, parryware. 48 ptmt grating dooms of size 150 mm square and provision of hinge system to open and closing of cocroch trap. make : prayag, gem or equivalent. 49 pvc water tank cover for 500 ltr. make : sintex / polycone / renutuff / cera. 50 pvc water tank cover for 1000 ltr tank. make : sintex / polycone / renutuff / cera. 51 gi socket 20mm isi marked. 52 gi socket 15mm isi marked. 53 gi elbow 15 mm isi marked. 54 gi elbow 20 mm isi marked. 55 gi nipple 15mm x 100 mm isi marked. 56 gi nipple 15mm x 125 mm isi marked. 57 gi nipple 15mm x 150 mm isi marked. 58 gi nipple 15mm x 50mm isi marked. 59 gi nipple 15mm x 75mm isi marked. 60 gi nipple 20mm x 100 mm isi marked. 61 gi nipple 20mm x 125 mm isi marked. 62 gi nipple 20mm x 150 mm isi marked. 63 gi nipple 20mm x 50 mm isi marked. 64 gi nipple 20mm x 75 mm isi marked. 65 gi plug 15mm. 66 gi plug 20mm. 67 gi reducer elbow 20 mm x 15mm isi marked. 68 gi reducer elbow 25mm x 20mm isi marked. 69 gi reducer socket 20mm x 15 mm isi marked. 70 gi reducer socket 25mm x 15mm isi marked. 71 gi reducer socket 25mm x 20mm isi marked. 72 gi reducer tee 20 mm x 15mm isi marked. 73 gi tank nipple 15 mm isi marked. 74 gi tank nipple 20 mm isi marked. 75 gi tee 15 mm isi marked. 76 gi tee 20 mm isi marked. 77 gi union 15mm isi marked. 78 gi union 20mm isi marked. 79 washer for syphone sets internal / external dia of washer as required. make as per sample 80 stainless steel sliding telescopic channels having length 450 mm for kitchen cupboard drawers and shelves. make: godrej, hettich or equivalent. 81 stainless steel sliding telescopic channels having length 600 mm for kitchen cupboard drawers and shelves. make: godrej, hettich or equivalent. 82 stainless steel welding rod for s s metal welding ( dia of rod 3.15 and length 350mm ) . 83 welding rod ( electrodes ) for metal arc welding ( dia of rod 3.15 mm and lenth 350mm ) . 84 chromium plated brass 32mm bottle trap with 300 mm and 190 mm long wall connection flange pipe. make hindware, parryware, cera or gem, prayag. 85 chromium plated brass hand shover ( health faucet ) with 8 mm dia, 1.2 mtr long telephonic flexible tube & wall hook. make : cera, hindware, prayag, gem or parryware. 86 chromium plated brass 15 mm dia angular stop cock with wall flange. make : cera, hindware, prayag, gem or parryware. 87 wall mixer with provision for over head shover with 115 mm long bend pipe on upper side, connecting legs and wall flanges. make : cera, hindware, prayag, gem or parryware. 88 15mm dia chromium plated bib taps. make : cera, gem, hindware, parryware or prayag. 89 15 mm dia ptmt bib taps. make : prayag, polytuf. 90 15 mm dia chromium plated pillar tap. make : cera, gem, hindware, parryware or equivalent. 91 bevelled edge frame less looking mirror of rectangular shape of size 600 x 450 mm with wall mounting arrange ments. make: prayag, modi, tripurti. 92 110 mm dia pvc swr bends make as per sample kept in ge office. 93 75mm dia pvc swr bends make as per sample kept in ge office. 94 100 mm oval / round shape cast iron pipe covers for cast iron vertical stacks make as per sample kept in ge office. 95 75 mm oval / round shape cast iron pipe covers for cast iron vertical stacks make as per sample kept in ge office. 96 ewc seat covers with mild steel hinging device. make: cera, prayag, hindustan, hindware. 97 stainless steel curtain rod 25mm dia. make : as per sample kept in ge office. 98 statinless steel bracket for curtain rod 25mm dia wall to wall ( end bracket ) , l type. make : as per sample kept in ge office. 99 statinless steel desginer end ( laatu ) for curtain rod 25mm dia. make : as per sample kept in ge office. 100 25mm dia ms powder coated as in approved colour curtain rod for doors and windows. make : as per sample kept in ge office. 101 ms powder coated as in approved colour bracket for curtain rod of 25mm dia. make : as per sample kept in ge office. 102 ms powder coated as in approved colour designer end dooms for curtain rod of 25mm dia. make : as per sample kept in ge office. 103 m seal 100gm pkts. make : as per sample kept in ge office. 104 continous piano himges, 180 degree with holes, stainless steel wide 32mm. make : as per sample kept in ge office. 105 nickel chrome handle for cupboard of size 100mm. make : as per sample kept in ge office. 106 oil putty for fitting of glass panes. make : as per sample kept in ge office. 107 urinal waste pipe with nuts 750mm long. make : as per sample kept in ge office. 108 pvc waste pipe for washbasin, kitchen sink etc. of length 750mm & dia 32mm. make : as per sample kept in ge office. 109 flush down pipe 90 degree for low level of flushing cistern. make : as per sample kept in ge office. 110 gi tube medium grade of size 15mm isi marked. 111 gi tube medium grade of size 20mm isi marked. 112 15mm ball valves, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball. make : as per sample kept in ge office. 113 20mm ball valves, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball. make : as per sample kept in ge office. 114 wash basin bracket of cast iron, length upto wash basin length. make as per sample kept in ge office. 115 gi clamp for tube, of size 15mm to 55mm & width 0.5 to 1 inch with corrosive resistant make as per sample kept in ge office. 116 threads for pipe sealent. make as per sample kept in ge office. 117 pvc corner shelf ( set of 3 ) . make: as per sample kept in ge office. 118 prespex sheet 3mm thick with transparent with clear visibility. make as per sample kept in ge office. 119 pvc connection with ptmt nut of size 450mm. make : as per sample kept in ge office. 120 pvc connection with ptmt nut of size 600mm. make: as per sample kept in ge office. 121 roval plug make as per sample kept in ge office. 122 stainless steel chorme towel ring. make as per sample. 123 stainless steel wall ounted soap dish. make as per sample. 124 frosted glass 4mm thick. make : modiguard, saint gobain. 125 sink coupling 2 size make as per sample kept in ge office. 126 sink coupling 4 size make as per sample kept in ge office. 127 waste coupling 32mm size make as per sample kept in ge office 128 plain glass sheet 3mm thick. make : modiguard, saint gobain. 129 ms sliding door bolt 250mm along locking plate isi marked. 130 ms sliding door bolt 300mmalong locking plate isi marked. 131 ms handle 150mm oval shape isi marked. 132 aluminium handle 150mm fabricated type. 133 ms tower bolt 100mm isi marked. 134 ms tower bolt 150mm isi marked. 135 aluminium tower bolt 100mm isi marked. 136 aluminium tower bolt 150mm isi marked. 137 aluminium hasp and staple 150mm isi marked. 138 pvc cistern 10 ltr capacity with ball valve, superflow / flush kit complete set. make : prayag, hindware , cera. 139 chromium plated 15 mm dia wash hand basin mixer. make : cera, jainko, or equivalent 140 chromium plated 15 mm dia swan neck sink mixer. make: cera, jainko. 141 mouchi nails 1 / 2 make as per sample. 142 5.50mm thick tinted glass. make modiguard, saint gobain. 143 alluminium die cast body door closer hydraulically regulated, designation no. 2, universal type, for door weight between 36 to 60 kg. make : everest, universal, godrej. 144 lime ( calcium oxide ) 20 kg bag. make suryacem. 145 water based oil bound distemper in approved colour. make: asian, berger or equivalent 146 synthetic enamel paint for wooden and steel surfaces. make: berger, asian or equivalent. 147 thinner for enamel paints ( min flash point 40 degree ) . 148 paint brush 4 inch wide flat with wooden handle as per sample. 149 paint brush 3 inch wide flat with wooden handle as per sample. 150 paint brush 2 inch wide flat with wooden handle as per sample. 151 premixed bitumin ( bituminus cold mix ) 20 kg bag. make boral. 152 chromium plated 600 mm length towel rod. make : cera, bharath, hindware. 153 fevicol sr adhessive. 154 vitreous china wash basin, white, flat back, size 580x450mm including brackets. make : cera, hindware, hindustan. 155 vitreous china wash down water closet pan ( pedestal pattern ) . make: cera, hindware, hindustan. 156 vitreous china squatting pan, ‘orissa’ pattern, size 580 x 440 mm white, with integral foot rests. make : cera, hindware, hindustan. 157 stainless steel sink, 1.00mm thick for kitchen, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 20mm with bowl size 410mm x 330mm x 160mm make : blue star, nirali. 158 stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm. make : blue star, nirali or equivalent. 159 flench / cap for cp bib tap, stop cock etc. make as per sample kept in ge office. 160 4 pole ( mcb fp ) of 63 / 80 amp 240 / 415 volts 10 ka finger proof terminal, bi connect termination, label holder, 50 mm² terminal capacity, insulated sliding shutter, large two position dolly. 161 4 pole ( mcb fp ) of 100 amp 240 / 415 volts 10 ka finger proof terminal, bi connect termination, label holder, 50 mm² terminal capacity, insulated sliding shutter, large two position dolly. 162 4 pole ( mcb fp ) of 125 amp 240 / 415 volts 10 ka finger proof terminal, bi connect termination, label holder, 50 mm² terminal capacity, insulated sliding shutter, large two position dolly. 163 2 pole ( mcb dp ) of 63 amp 240 volts 10 ka c curve finger proof terminal, bi connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly. 164 1 pole ( mcb sp ) of 25 amp 240 volts 10 ka c curve finger proof terminal, bi connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly. 165 single core insulated copper wire of 6 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 166 single core insulated copper wire of 4 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 167 single core insulated copper wire of 4 sqmm of black colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 168 single core insulated copper wire of 2.5 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 169 single core insulated copper wire of 2.5 sqmm of black colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 694. 170 single core insulated copper wire of 2.5 sqmm of green colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 695. 171 single core insulated copper wire of 1.5 sqmm of red colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 695. 172 single core insulated copper wire of 1.5 sqmm of black colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 695. 173 single core insulated copper wire of 1.5 sqmm of green colour codeing as per is with frlsh smoke free non toxic, non corrosive confirming to is : 696. 174 round sheet of plastic for fan box. 175 round sheet of bakelite for junction box. 176 lamp holder, pvc / polycarbonate type. 177 switch piano flush type single pole, one way 5 amp. 178 socket piano flush type single pole, one way 5 amp. 179 multi socket outlet piano flush type 5 pin 5 & 15 amp. 180 fan regulator socket type. 181 capacitor 3.15 mfd as per is code. 182 modular white cover plate with frame, 1 module / 2 module. 183 modular white cover plate with frame, 3 module. 184 modular white cover plate with frame, 6 module. 185 modular white cover plate with frame, 8 module. 186 modular white cover plate with frame, 12 module. 187 modular bell push switch, 6 a, 1 module. 188 modular socket, 6a 2 / 3 pin combined, 2 module. 189 modular switch 6a, 1 module. 190 modular switch 16 amps, 1 module with indicator. 191 modular socket 16 amps, 6 pin, 2 module. 192 modular fan step regulator, 120w 1 module. 193 modular blank switch 1 module. 194 ac plug top 2p +earth. 195 ac socket 2p +earth. 196 bakelite sheet 4 x 4. 197 bakelite sheet 7 x 4. 198 bakelite sheet 8 x 10. 199 bakelite sheet 11 x 12. 200 flexible pipe of 20 mm dia. 201 screws of 1.0 inch. 202 screws of 1.5 inch. 203 screws of 2.5 inch....

Military Engineer Services - Punjab

20329365 tender for provision of bazar supply items=> open tender: 24 galvanised iron ms wire cloth, 0.63 mm nominal dia of wire and average width of apreture 1.4 mm. make agtha / elephant or equilvent note wiremesh roll should be 1.2 mtr wide to avoid wastage. 25 0.56 mm plain aluminium sheet 26 plywood grade bwp type bb 6 mm thick, commercial facing make centuary / kitply / flagnapple / forever 27 plywood grade bwp type bb 4 mm thick, commercial facing make centuary / kitply / flagnapple / forever 28 aluminium standard door bottom seal with nylon brush at lower side to fit at the bottom of door shutter upto 1.1m length. 29 flexible rubber 5 mm th 50 mm wide for door bottom seal. 30 neoprene beading for aluminium windows / doors glass fixing 31 aluminium butt hinges 100 size. make: crown 32 aluminium butt hinges 75 size. make: crown 33 aluminium sliding door bolt 300 mm along with locking plate 34 aluminium sliding door bolt 250 mm along with locking plate 35 mild steel wire nails with head for wiremesh ( black ) size n exc 20mm. make as per sample 36 mild steel wire nails with head for wiremesh door bidding, fixing of plywood and size not exc 25mm ( 17 nos ) . make as per sample 37 mild steel wire nails with head for door repairs size not exc 50mm ( 12 nos ) . make as per sample 38 mild steel wire nails with head for size not exc 25mm ( 14 nos ) . make as per sample 39 mild steel wire nails with head for size not exc 50mm ( 10 nos ) . make as per sample 40 mild steel wire nails with head for size not exc 100mm ( 8 nos ) . make as per sample 41 mild steel wire nails with head for size not exc 100mm ( 10 nos ) . make as per sample 42 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded.size 75x10. make as per sample 43 mild steel machine screws, bright finished, with slotted countersunk head, full length threaded n exc 50mm ( black ) . make as per sample...

Military Engineer Services - Punjab

20153060 tender for provision of bazar supply items=> open tender: 24 galvanised iron ms wire cloth, 0.63 mm nominal dia of wire and average width of apreture 1.4 mm. make agtha / elephant or equilvent note wiremesh roll should be 1.2 mtr wide to avoid wastage. 25 0.56 mm plain aluminium sheet 26 plywood grade bwp type bb 6 mm thick, commercial facing make centuary / kitply / flagnapple / forever 27 plywood grade bwp type bb 4 mm thick, commercial facing make centuary / kitply / flagnapple / forever 28 aluminium standard door bottom seal with nylon brush at lower side to fit at the bottom of door shutter upto 1.1m length. 29 flexible rubber 5 mm th 50 mm wide for door bottom seal. 30 neoprene beading for aluminium windows / doors glass fixing 31 aluminium butt hinges 100 size. make: crown 32 aluminium butt hinges 75 size. make: crown 33 aluminium sliding door bolt 300 mm along with locking plate 34 aluminium sliding door bolt 250 mm along with locking plate 35 mild steel wire nails with head for wiremesh ( black ) size n exc 20mm. make as per sample 36 mild steel wire nails with head for wiremesh door bidding, fixing of plywood and size not exc 25mm ( 17 nos ) . make as per sample 37 mild steel wire nails with head for door repairs size not exc 50mm ( 12 nos ) . make as per sample 38 mild steel wire nails with head for size not exc 25mm ( 14 nos ) . make as per sample 39 mild steel wire nails with head for size not exc 50mm ( 10 nos ) . make as per sample 40 mild steel wire nails with head for size not exc 100mm ( 8 nos ) . make as per sample 41 mild steel wire nails with head for size not exc 100mm ( 10 nos ) . make as per sample 42 mild steel wood screws, bright finished, with slotted countersunk head, half or full length threaded.size 75x10. make as per sample 43 mild steel machine screws, bright finished, with slotted countersunk head, full length threaded n exc 50mm ( black ) . make as per sample...

Military Engineer Services - Punjab

18703251 provision of certain sanctioned works under age br ii ge north patiala, ge ( n ) / pat 39 / 2018 19 11.00 treating with anti termite treatment to backfill in contact with foundation at the rate of 7.5 litre of emulsion per square metre of surface complete all as specified and directed. 12.00 treating with anti termite treatment at the top surface of filled earth at the rate of 5 litre of emulsion per square metre of surface complete all as specified and directed. 13.00 treating the soil along with external perimeter of building with anti termite treatment at the rate of 2.25 litre of emulsion per square metre of surface area complete all as specified and directed. 14.00 reinforced cement concrete m 25 (design mix) as in footing of column and the like, complete all as specified and directed. 15.00 reinforced cement concrete m 25 (design mix) as in column, pillars and the like, complete all as specified and directed. 16.00 reinforced cement concrete m 25 (design mix) as in beams, lintel beams, chajjas, facia, lintel band and the like, complete all as specified and directed. 17.00 reinforced cement concrete m 25 (design mix) in slabs supported on walls, beams, landings, balconies, canopies, desk slabs and in shelves and the like, complete all as specified and directed. 18.00 form work to soffits of suspended slabs such as roof slab, floor slab, beams, sides of foundation, pillars etc. for rough finish surface complete all as specified. 19.00 form work to sides of slab, shelves etc exc 5 cm but not exc 10 cm wide for rough finished surfaces complete as as specified. 20.00 8 mm dia and over mild steel tmt bars as in reinforcement , cut to length, bent to shape required, incl cranking and binding with ms wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed....

Sant Longowal Institute Of Engineering And Technology - Punjab

17140583 disposal of dismantled material brass angle valve, brass valve cock, brass ferrule, brass gate valve, brass rod, brass stock cock, cp angle valve? cp bib cock, cp bottle trap, cp grating jail, cp lab tap, cp pillar cock, cp urinal spreader, cp shower, cp waste jali, cp towel rail, jumper valve, spindle face etc, cl cistern, ci curtain bracket, cl curtain ring, curtain rod, door closer, door handle, door lock, door spring, door viewer, door railing, floor door spring, i)raj lock, gi bend, gi elbow, gi clamp, gi hex nipple, gi nipple, gi nut bojt, gi pipe, gi plug, gi reducer, gi socket, gi tank nipple, gi tee, gi union, gi wire mesh jail, gi weld mesh jali, hole fast, hy door closer, health faucet, jet, lock 6 liver, ms angle, ms door handle, ms aldrop, ms door spring, ms door stopper, ms hinges, ms kundi chapka, ms tower bolt, ms wire mesh jali, ms cockroach jali, ms stay patti, ms window stopper, jali window, jail and glass window, bathroom ventilation (iron), grill with fibber, grill, ci pipe, iron frame with door, tee angle, steel, gi pipe with fitting, ms hook etc , alum door handle, alum door lock, alum door stopper, alum tower bolt etc , pvc ball, pvc ball cock, pvc cistern, pvc cistern handle, pvc cistern kit, pvc connection pipe, pvc elbow, pvc pipe, pvc urinal syphone, pvc waste pipe, pvc water tank (750, 1000 & 3000 ltr), seat cover, wall to wall tk cover etc, unserviceable /broken wooden door and windows etc, unserviceable /broken wash basin & ewc seat etc, empty cement bag , steej. kitchen sink, ci n.rv 100mm , ci sluice valve...

Sant Longowal Institute Of Engineering And Technology - Punjab

17072736 supply of material brass angle valve, b i ass valve cock, brass ferrule, brass gate valve, brass rod, brass stock cock, cp angle valve, cp bib cock, cp bottle trap, cp grating jali, cp lab tap, cp pillar cock, cp urinal spreader, cp shower, cp waste jail, cp towel rail, jumper valve, spindle face etc , cl cistern, ci curtain bracket, cl curtain ring, curtain rod, door closer, door handle, door lock, door spring, door viewer, door railing, floor door spring, draj lock, gi bend, gi elbow, gi clamp, gi hex nipple, gi nipple, gi nut bojt, gi pipe, gi plug, gi reducer, gi socket, gi tank nipple, gi tee, gi union, gi wire mesh jali, gi weld mesh jail, hole fast, hy door closer, health faucet, jet, lock 6 liver, ms angle, ms door handle, ms aidrop, ms door spring, ms door stopper, ms hinges, ms kundi chapka, ms tower bolt, ms wire mesh jali, ms cockroach jali, ms stay patti, ms windoxv stopper, jali window, jali and glass window, bathroom ventilation (iron), grill with fibber, grill, ci pipe, iron frame with door, rfee angle, steel, gi piue with fitting. ms hook etc , alum door handle, alum door lock, alum door stopper) alum tower bolt etcpvc ball, pvc ball cock, pvc cistern, pvc cistern handle, pvc cistern kit, pvc connection pipe, pvc elbow, pvc pipe, pvc urinal syphone, pvc waste pipe, pvc water tank (750, 1000 & 3000 ltr), seat cover, wall to wall fk cover etcunserviceable /broken wooden door and windows etc unserviceable /broken wash basin & ewc seat etc empty cement bag 8 steel kitchen sink ci n.r.v 100mm ci sluice valve...

Military Engineer Services - Punjab

14062282 provision of bazar supply items: 32 galvanised iron ms wire cloth, 0.56 mm nominal dia of wire and average width of apreture 1.18 mm. note wiremesh roll should be 1.2 mtr wide to avoid wastage. 33 pvc plugs for fixing screws to drill holes. make as per sample 34 synthetic enamelled paint of any colour as directed. make nerolac ( nerock ) / asian ( apcolite ) / berger ( luxol hi gloss ) 35 sheet glass ordinary quality 4 mm thick. make modiguard / saint gobin or equilvent 36 sheet glass pin headed 4 mm thick. make modiguard / saint gobin or equilvent 37 block board commercial 18 / 19mm thick, grade 1 quality , exterior grade commercial type , make kitply / green ply / novapan 38 plywood 6 mm thick, commercial facing, 8x4 grade bwr, type bb , make kitply / green ply / novapan 39 plywood 4 mm thick, commercial facing, 8x4 grade bwr, type bb , make kitply / green ply / novapan 40 oil putty. make as per sample 41 5 mm thick flexibale rubber black coloure. make as per sample...