Department of Cooperation - Punjab

37830480 supply of pump and pumps spares , supply of pump spares , make kirlosker / sintech/gita type shm 150x32 h 25 mtrs q 288 lps rpm 960 size 150x150mm, hp 20 moc – pump casing ss 304,casing cover ss 304 , impeller ss 304, sleeve ss 304, shaft ss 304 , make kirlosker / sintech/gita pump type kpd 125x45 q 160 cum /hr.,h 60mtr, size 125x150mm, rpm 1440, moc– pump casing ss 304,casing cover ss 304 , impeller ss 304, sleeve ss 304, shaft ss 304 , make kirlosker / sintech/gita pump type shm 100x32n q 160 cum /hr.,h 12mtr, size 100x125mm, rpm 960 moc – pump casing ss 304,casing cover ss 304 , impeller ss 304, sleeve ss 304, shaft ss 304 , make kirlosker / sintech/gita model –cps 50/200 q 35 cum /hr.,h 60mtr, size 80x50mm, rpm 2900, mos – ci impeller & sleeve ss 304, shaft ss 304 , make kirlosker / sintech/gita pump type shm 100x32n q 80 cum /hr.,h 12mtr, size 100x125mm, rpm 960, moc – pump casing ss 304,casing cover ss 304 , impeller ss 304, sleeve ss 304, shaft ss 304 , sulphured juice pump make : kirlosker type kpd 125/45 capacity: 200m3 /hr. head :60 meter rpm:1440 pump input :44.55 kw size: 125x150 prime movers rating 55 kw moc – pump casing ss 304,casing cover ss 304 , impeller ss 304, sleeve ss 304, shaft ss 304 , clear juice pump make : kirloskar type kpd 125/45 capacity : 180 m3/hr head : 70 meter rpm 1440 moc – pump casing ss 304,casing cover ss 304 , impeller ss 304, sleeve ss 304, shaft ss 304 , make kirlosker mud filtrate pump size 80x65 head 25 meter rpm 1440 cap. 40 m3/h moc – pump casing ss 304,casing cover ss 304 , impeller ss 304, sleeve ss 304, shaft ss 304 , make kirloskar /sintech / gita superheated wash water pump sucxdel :65x40mm rpm : 2900 total head : 80 meter capacity 36 cubic meter/hr size & type: 40 260 , kirloskar/ sintech / gita kpd – 50/32 head – 30 mtr size – 50x30 mm hp7.5 capacity 30m3/hrrpm 1440 material of shaft – en 8 body construction – ci ci impellor, sleeve ss 304 , make.kirloskar /sintech / gita type sp4l,head 12m size: 100mmx100mm capacity 50 60 m3/hr material of shaft ss 304,sleeve ss 304 body contraction c.i. impeller , spare for sulphured juice pump (make : kirlosker capacity: 200m3 /hr. head :60 meter body: s.s. impeller: 304 grade material shaft s.s. 304 grade rpm:1440.impellers.s. body pump input :44.55 kw size: 125x150 prime movers rating 55 kw) , impeller ss 304 , casingcover ss 304 , sleeve ss 304 , bodycasing ss 304 , spares ofhigh flow pumps capacity size: 6.0 inch x 6.0 inch, make risansi , steel claded rubber statorlength:375mm ,od 165 mm as per drg. , ss bush , ss bush pin , head pin , rotor , rubber boot , head pin , circlip big , circlip small , spares ofhigh flow pumps capacity size: 4.0 inch x 4.0 inch,make risansi , rubber stator . , ss bush , ss bush pin , head pin , rotor , rubber boot , head pin , circlip big , circlip small , ci impellor for sp6l type sludge pump , spares for mill house raw juice pump kirloskar type type shm 150x32 h 25 mtrs q 288 lps rpm 960 size 150x150mm, hp 20 , impeller ss 304 , casingcover ss 304 , sleeve ss 304 , bodycasing ss 304 , spares for mill house raw screened juice pump kirloskar type pump type kpd 125x45 q 160 cum /hr.,h 60mtr, size 125x150mm, rpm 1440 impeller ss 304 , casingcover ss 304 , sleeve ss 304 , bodycasing ss 304 , spares for mill house raw juice pump kirloskar type pump type shm 100x32n q 160 cum /hr.,h 12mtr, size 100x125mm, rpm 960 , impeller ss 304 , casingcover ss 304 , sleeve ss 304 , bodycasing ss 304 , kakati ppi make vcacuum pump type kvm 100 rpm 1250, capacity 690m³ /hr at open suction vacuum 660 mm hg with v belt drive parts material : body head and cone ci gr. fg. 260 roter (impeller) sg iron shaft en8, shaft and sleve ss including accessary with one vacuum guage and one water pressure guage perrformance test will be as per bs1571 part ii 1975...

Department of Cooperation - Punjab

32298800 fabrication and erection jobs of bhogpur csm 1 bhogpur csm 2 fabrication and erection of cane unloader bridge platform 3 dis, feb, & errection of umbrella of pan along with its supports. 4 dismantling, fabrication & erection of vapour pipe 700mm and 900mm& 1000 mm from 8 / 10mm thick plate. 5 rmp pipes & clusters replacement of spray pond.pipe 6 b ) cluster 7 c ) reducer 8 d ) blind 9 dismantling of spray pump header, fabrication, erection and fitting ofpumps etc 10 fabrication & erection of bagasse elevator stair case & platform 11 replacement of brass / ss tubes of pans 12 dismantling and erection of various sizes of ms and gi pipe lines up to 1 3 / 4 dia 13 dismantling and erection of various sizes of ms / gi pipe lines from 2’’to12” dia. 14 dismantling, fabrication and erection of ms pipe above 12’’ dia from msplate and shifting / dragging it as per direction. 15 fab.and fitting of ms flange complete with holes by drilling up to 12’’dia 16 fab.and fitting of ms flange complete with holes by drilling above 12’’dia 17 dis. and cleaning of ms flange from old pipe lines. 18 fabrication and erection of following items from ms pipe up to 12” dia.a ) ms nipple 19 b ) ms bend 20 c ) m s tee 21 d ) ms cross 22 e ) ms reducer 23 f ) m s cone 24 fabrication and erection of following items from ms pipe up to 12” dia.a ) ms nipple 25 b ) ms bend 26 c ) m s tee 27 d ) ms cross 28 e ) ms reducer 29 f ) m s cone 30 dismantling and fitting of gi / acc sheet.dismantling 31 fitting 32 dismantling of machinery and structure as instruction of ce 33 fabrication and erection of machinery and structure. 34 erection of machinery 35 patch work of different equipments such as cane carrier, and intercarrier. 36 dismantling and erection of worn out runners of cane carrier, rbc, bagasse elevator and inter carrier 37 to straight the old damaged vapour pipe and round tank for platform. 38 dis, feb, & errection of steam coil of molasses storage tank at pan stationsize 1” to 2”. 39 dis, feb, & errection of juice coil of juice clarifier size 4”, 5” & 6” alongwith its nipple. 40 dis, feb, & errection of open & closed crystallizers arms 41 dis.feb & eraction of wt. juice sulphited juice stainer 42 dismantling, fab. & erection of ss pipe up to 12’’ 43 dismantling, fab. & erection of following items upto 12’’ of ssss nipple, 44 ss bend 45 ss tee 46 ss cross 47 ss reducer 48 ss cone 49 dismantling, fab. & erection of ms flat ( runner ) , cane carrier, rbc chainetc. 50 dismantling, fab. & erection of motor bed with alignment 51 dismantling of complete exiting calendria 600 m2 h.s. & each tube alsocomplete to be dismantling. 52 erection of milk of lime new hopper along with staging , platform &drive. fitting of wooden strips 53 fabrication & erection of 30 tons capacity sugar melter completescope of worka work to be completed as per drawing.b fabricate & erection of ms 10 mm thick plate of app size:3.5mx3.5 mc fitting of stirrer drive.d fitting of perforated plates having hole dia 1.5 mm allalong the platese drive stirrer to be mounted along with shaft & ss ball 2.0inch ball.f fabricate & erect of steam coil 02 nos. periphery insidethe drumg fabrication of staging on which drum to be mounted.h outlet pipe 12.0 inch dia tobe provided.i steam coil along with nrv & valves to be fitted.j hot water connection to be made along with valves.k dismantling of reduction gear & motor & to be fitted on itfrom old mill.l alignment of reduction gear to be made with motor.m repair of reduction gear.n water trial of complete unit.o fabrication & erection of platform 54 magma mixture for brown sugar reprocessingscope of worka dismantle the magma mixture from old mill and to erect atsuitable place at new mill.b dismantle & erection of magma pump, molasses pumpalong with pump beds.c fabrication of staging and platforms along with m.s. stairs.d dismantle of stirrer drive and erection of it along withmotor.e trial of complete unit. 55 dismantling & fitting of ss tubes in calendriasize: 45mm odx1.2mm thickx2010mm long 56 size:98 mmodx1.6mm thickx905 mm long 57 dismantling, fabrication and erection of pansave all top plate 58 shifting & erection of seed mixture at new millscope of worka dismantle of dry seed mixture from old factory.b erection of same along with drive at the top of dry seedcrystallizer at new millc proper staging to be made.d hot water connection to be made. 59 dismantling, fabrication and erection of drain gutter of sugar drierhouse 60 replacement of sugar hopper plates of all 03 nos.scope of worka dismantle of old worn out plates.b fabricate of new plate of hopper of 05 mm thick according toexisting size.c proper strengthening of plates.d erection of complete hopper along with accessoriese fitting of crank shaft with crank shaft.f fitting of rori jail along with frame.g fitting of powder sugar jali with frame. 61 shifting of old sugar hopperscope of worka dismantling of old sugar hopper from old factory along withdrive.b erection of hopper at new mill site in dryer house.c refurbishment of hopper plates.d fitting of wooden all stripse erection of connecting rod along with drive.f accessories to be made relating to hopper 62 planetary gear boxerection of planetary gear box at crystallizer 63 replacement of central shaft.fabrication & erection of shaft, along with helis type stirrer of b vacuumcrystallizer 64 erection of gear operated butterfly valve in place of discharge valve inpans 65 fabrication & erection of pneumatic shoot 66 erection of pneumatic clamps 67 replacement of old gate valve with new gate valve of crystallizers 68 dismantling of double beat valve and erection of same of juice heater at existing site. 69 shifting of nk 1100 continuous centrifugal machine along with pug mill, magma mixture, magma pump, molasses pump and pipe line from oldplant to new plant.scope of work:a dismantling of nk 1100 continuous centrifugal machine fromold mills at existing site along with magma pump, molassespump, drive, motor, foundation beds, pipe lines , pugmill alongwith drive, magma pump along with its drive from old mills.b dismantle of existing staging of machine, pug mill, magmamixture etc.c erection of nk 1100 continuous centrifugal machine along withaccessories at mill at suitable place.d rebufbishment of any parts seems weak to be carried out.e water level to be madef erection of motor bed along with motor.g erection of pugmill, magma mixture, magma pump, molassespump along with all drives , foundation bed relating to machine.h proper platform to be made.i complete water trial of unit 70 shifting & erection of cfw continuous centrifugal machine from old millto new millscope of worka dismantling of pug mill along with drive.b dismantling of centrifugal machine along with motor.c dismantling of magma mixture along with drive.d dismantling of magma pump & molasses pump along with foundation bed.e erection of machine in new mill along with motorf erection of pug mill along with drive.g erection of magma mixture along with drive.h erection of magma pump & molasses pump along with drive.i erection of staging & platform to be done.j complete trial of units. 71 shifting & erection of air compressors & super heater wash watersystem from old mill to new millscope of work:a dismantling of air compressors along with motors.b dismantling of its pumps & motorc dismantling of all accessoriesd erection of air compressors along with motorse erection of pumps and motors 72 shifting & erection of injection pump with motor from old mill tonew plant. 73 dismantling of mud mixture from old mill and to erect the same innew mill at vacuum filter station along with accessories with related connection. 74 dismantling of transient heater from old mill and to erect thesame in new mill at centrifugal station along with accessories withrelated connection. 75 dismantling , fab.& erection patch work of inter rake carrier side plate 76 dismantling , fab.& erection main bagasse carrier trough & side plate 77 fabrication & erection of bagasse elevator stair case &platform 78 fabrication & erection of factory structure complete window ( frame &grills ) 79 dismantling , fab. & erection of mill house & boiler house plate form 80 modification, & erection of mill house rotary screen inlet juice tank& platform 81 fabrication and erection of excess bagasse carrier to rbc as per thedirction of ce scope of work ( a ) fabrication and erection of column and structure for belt conveyor , along with drive system and discharge chute to rbc column and steelstructure 82 ( b ) dismantling of belt conveyor and its structure along with drivecomplete in all respect 83 dismantling , shifting & erection of old plant bagasse yard shed to new plant bagasse yard 84 fabrication and erection of cooling tower structure and shed 85 shifting & erection of cane unloder trolly gear box with motor old plant to new plant 86 fabrication and erection of excess bagasse carrier to rbc as per the dirction of ce scope of work 87 dismantling & erection of following items from c.i pipe up to 12” dia.a ) c.i bend 88 b ) c.i tee 89 c ) c.i cross 90 dismantling and erection of various sizes of c.i pipe lines from 2’’to 12” dia. 91 dismantling , shifting & erection of old plant cane carrier unloader shed to new plant unloder shed 92 dismantling , fab. & erection of mbc motor bed with alignment 93 fab. & erection of electrical poll 94 modification, & erection of boiler prds line 95 modification of mud mixture scope of worka to increase length 1.2 meter of mud mixture shell.b to increase stirrer length 1.2 meter lengthc to erect all connecting pipe lines.d to fabricate & erect scroll up to the length of mud mixture.e shifting of outlet mud withdrawal pipes. 96 filtrate juice receiving tank scope of worka filtrate juice tank dia1900mmx1260mm height to be fabricated and erected to increase the height of tank.b all connecting pipe lines ( having 3.0dia ) to be re erected after dismantling of lines, valve etc which were dismantled.c all suction connections of pumps to be made. 97 dismantling of syrup pipe line and re fitting after cleaning the same. a dismantling 98 b refitting 99 sugar hopper ( app.45meter ) a dismantling 100 b ) fabrication 101 c ) erection 102 butterfly valvea dismantling 10inch dia to 16.0 inch dia 103 b erection 10inch dia to 16.0 inch dia 104 sluice valvea dismantling 10inch dia to 16.0 inch dia 105 b erection 10inch dia to 16.0 inch dia 106 a dismantling and erection of transient heater from old mill to new mill 107 b dismantling of transient heater from existing site at new mill 108 fabrication of multi tray of sugar hopper wide 1.5 meter 109 erection of top &bottom tube plates of evaporator body along with tie rods. 110 fabrication & erection of calendria shell of 600 square meter along with down take, vapour pipe, non condensable gas pipe line, clear juice inlet outlet juice connection. 111 dismantling of reduction gear, motor, stirrer shaft of juice sulphiter from old mill to new mill. 112 fabrication and erection of monkey ladders 113 erection of flow meter valve dia 6.0 inches 114 erection of sludge pump along with pumps size: 4x4 inches 115 :6x6 inches 116 dismantling, fabrication & erection of gate valve of crystallizersize: 08 inches 117 size :10 inches dia 118 dismantling , fabrication and erection of distributor of pan 119 fabrication & erection of wire netting frame and its wire netting 120 fabrication & erection of sugar tray of hopper under neath hopper no.3. 121 dismantling , erection of butterfly valves in place of old discharge valve along with modifications of massecuite gutter. 122 erection of chimney of juice sulphiter ( 8.0 inch dia ) and clarifier ( 10.0 inch dia ) 123 modification of juice box of clarifier juice outlet pipes to be decreased by 200mm dia height ( 104 nos pipes ) 124 modification of syrup sulphiter scope of worka holes to be increased from existing perforated plates 03 nos. plates of recovery tower ( 600mm dia plate ) b holes to be increased from existing plates of drums ( big &small plates ) .c so2 gas pipe lines to be modified.d spurger of so2 gas inside the drum to be modified.e flanges to be provided inside the ss. pipes.f man holes having dia 500 mm 03 nos. to be provided.g dismantling of 2.0 inches dia. pipes and erection of 4.0 inches dia to be erected . ( app. length. 18 meter ) h dismantling and erection of bend of outlet syrup lines ( 12.0 inches dia ) 125 sulphur furnacescope of worka dismantling of top cover of furnace to be opened.b baffle plate to be shifted 400 mm from existing site .c new 6.0 inches widex1200 mm plate to be fitted.d dismantling and erection of ms after burner.e dismantling, repair and erection of coolers 02 nos. of so2 pipesf dismantling and erection of distributor pipeg dismantling and erection of so2 pipes 126 side catcher of juice sulphiterscope of worka dismantling & refitting of old top coverb dismantling of internal 12 inches pipe up to length of catcher.c dismantling, fabrication , erection of manhole along with cover 500mm dia. 127 pans 6 nos scope of worka brass tubes to be taken out after breaking out from expand.b fitting of ss tubes and to make leak proof from expand.c all tubes to be made leak proof from expand.d calendria to be hand over after testing of normal pressure for hydraulic testing to mill fitter. 128 m.s. manhole with blind coversdismantling 129 b ) fabrication 130 c ) erection 131 scroll for mud mixture app 3.0 meter long and scroll dia 600 mma dismantling 132 b ) fabrication 133 c ) erection 134 fabrication & erection of deflection cone in centrifugal machines with proper angle 135 fabrication of water header along with nipples for supply of hot or cold water to centrifugals 136 vapour line juice heaterscope of worka blind to be provided in both inlet and outlet vapour pipe of quad.b hydralic testing to be done.c after testing of vljh , blind to be taken out. 137 fabrication of window with double door along with hinges and kundi 138 pan condensate tankscope of worka dismantling of old condensate tank from old mill.b shifting this tank from old mill to new mill.c dismantling of worn out pan condensate tank from existing site of new mill.d erection of pan condensate along with modification . 139 spray pump 2000 m3 / hrscope of worka dismantling of old spray pump from old millb erection of same at new mill.c modification of strainer of tail pipe.d dismantling of ms pipe app lengthe erection of ms pipe pipe.f erection of butterfly valve. 140 modification in sugar grader scope of gradera modification in ss wirenetting framesb dismantling of worn out of sealing plates , fabrication and erection at existing place.c modifications in hooks. 141 shifting of ms stairs with modification of sugar grader 142 dismantling of stairs from unloader side old mill and erection at sugar grader at new mill after modification 143 fabrication of erection of double beat valve flange 8.0 inches dia 144 juice sulphiter receiving tanka fabrication and erection of cover plateb fabrication and erection of man hole with blind cover 500 mmdia.c ladder to be providedfrom ground floor uptothe height of receiver. 145 erection of railing 146 dismantling & shifting of valves from old mills and fitting at new mills 08, 10, 12, 14, 16, 18, 20, 22, 24 , 26, 28, 30 inches diaa dismantling 147 b ) fabrication 148 c ) erection 149 modification in telescope valve of mud side, replacement of worn out bottom plate. 150 cold air blowera modification in bed 151 b dismantling and erection of blower 152 strengthening of angle iron channel 153 erection of angle channel in side the sugar elevator / dry seed elevator. 154 shifting of pan condenserscope of worka dismantling of old pan condenser alongwith tail pipe from old millb dismantling of existing condenser of pan no. 5 from new mill.c erection of same in place of pan condenser of pan no.5 at new mill. 155 dismantling & erection work of m / c gutter 156 dismantling & erection of air compressor tank 157 erection of sugar elevator window both side 158 fabrication and erection of shed for etp station electrical panel and motor pump 159 fabrication and erection of shed for dryer housesize 85feet x35 feet 160 shifting and erection of continuous centrifugal machines without pug mill and magma mixture from old mill to new mill.scope of work.a dismantling of centrifugal machines along with motor.b erection of machines in new mill along with motorc erection of staging & platform to be doned complete trial of machines.e rotate the magma mixture 90 degree.f water connection to be made.g dismantling of magma pumps, molasses pumps along with pump beds from old mill.h erection of magma pumps, molasses pumps along with pump beds at new pump.i complete trials of the unit. 161 erection of molasses pump. scope of work.a. fabrication new structure bed.b. erection of molasses pumps along with valves and complete pipe line ( 6” ) from centrifugal section to pan floor receiving tank.c. complete trial of molasses pumps. 162 dismantling & erection of m / c gutter size 510mmx490mm. 163 dismantling , fabrication & erection modification of structure of reduction gear box grader with alignment 164 modification in drive foundation bed of reduction gear box and motor sugar elevator. 165 job work of juice sulphiter modification revised scope of worka work to be completed in side the drum as per drawingb dismantling of existing 1.5 meter dia inside first drum.c dismantling of existing 2.5 meter dia inside second drum from juice sulphiterd perforated ms plates having 3.0 meter dia 03 nos along with 2.0 inch hole dia to be made to be fitted at site.e m.s. channels 100 mm to be fitted inside the drum.f stirrer shaft to be mounted along with bearing housing with 2.0 inches ball.g erection of reduction gear of stirrer drive.h alignment with reduction gear & motori dismantling of reduction gear & motor from old mill juice sulphiter.j 03 nos.manhole to be provided at suitable positionk modify of sperger and its dome.l rearranging of so2 and juice lines 166 modification in juice heaterscope of work1. dismantling / removal of all tubes of juice heaters by breaking of expand from top & bottom tube plates.2. length of all tubes to be reduced from 4460mm to 4000mm.3. cut down the bottom tube plate4. calendria shell length to be reduced from 4660mm to 4000 mm5. erection of bottom tube plate with the shell according to the length of tubes.6. bottom cover to be set right.7. hydraulic testing of calendria to be done at 60 psig. complete water trials. 167 dis of ms pipe line 168 dismantling, fab. & erection of inter rake carrier as per direction ce. scope of worka. dismantling , fabrication & erection of inter rake carrier side plate b .dismantling & fabrication of inter rake carrier dive &tail shaft sprocket distance pecsc .dismantling , fabrication & erection of inter rake carrier runner boxd. complete trials of inter rake carrier 169 fitting of g.i coler coated trapezoidal sheet 12 mtr 170 do 6 mtr 171 dismantling, fab. & erection of structure colum binder 172 repair of structure colum binder 173 dismantling, fab. & erection of ms angle & channel 174 dismantling, fab. & erection of perling / stress hannel 100x50 175 fabrication & erection of shed gutter size 1’x1’x’1’ plate 3mm thk. 176 shifting , dismantling , fabrication and erection of gantry for rbc sprocket and gear 177 modification of both side chain sprocket bed for mbc and rbc 178 cleaning & double coat painting for cane unloader shed structure 179 dismantling , fabrication and erection of runner box for mbc, rbc, and bagasse elevator 180 fabrication and erection of chute for mill to mill bypass system 181 modification in hot air blowerscope of worka. dismantling of air blowerb. modification in bedc. erection of blower....

Improvement Trust - Punjab

29780917 overhauling of damaged sewer line / storm sewer line / manholes and raising of the same, cleaning or road gullies and purchase of equipment like manhole detctor and submercible sludge pumps and submercible motor etc. in trust schemes. overhauling of damaged sewer line / storm sewer line / manholes and raising of the same, cleaning or road gullies and purchase of equipment like manhole detctor and submercible sludge pumps and submercible motor etc. in trust schemes....

Improvement Trust - Punjab

29241575 overhauling of damaged sewer lines / storm sewer lines / manholes and raising of the same, cleaning of road gullies and purchase of equipment like manhole detector and submersible sludge pumps and submersible motors etc in trust schemes. ...

Improvement Trust - Punjab

28571350 overhauling of damaged sewer lines / storm sewer lines / manholes and raising of the same, cleaning of road gullies and purchase of equipment like manhole detector and submersible sludge pump and submersible motor etc in trust schemes....

Improvement Trust - Punjab

28350338 overhauling of damaged sewer lines / storm sewer lines / manholes and raising of the same , cleaning of road gullies and purchase of equipment like manhole detector and submercible sludge pump and submercible motor etc in trust schemes . ...

Improvement Trust - Punjab

28056019 overhauling of damaged sewer lines storm sewer lines manholes and raising of the same , cleaning of road gullies and purchase of equipment like manhole detector and submercible sludge pump and submercible motor etc in trust schemes . ...

Water Resources Department - Punjab

24661401 tender for disposal of ms angle, channels, flats, ms round, sludge pumps, electric motor, portable magazine, battery scrap, copper scrap, aluminium scrap, brass scrap, acsr conductor, condemned vehicles, tyre, ms scrap, empty drum etc....

Military Engineer Services - Punjab

22119282 manning and operation of water supply installation no . 1 and water supply installation no . 2 at faridkot mil stn , manning & operation of centrifugal pump set / static plants of water supply installation no 2 including tightening of pump couplings , foundation nut bolts , thimbles of cable , replacement of u / s gland packing , gland ropes etc of pump sets or sluice valves , operation of sluice valve , caulking of lead joints of ci pipes in side the pump house or nearby area of water supply no 2 and also attending the filter bed for wash operation & cleaning of buds / bushes in side the pump house area & checking of raw water storage sump and water channel for nallah to new raw water pump house & to storage tank , cleaning of outside area and manning of dg set & other machinery / eqpt in side the pump house in 2 shifts of 8 hrs ( i . e from 0600 hrs to 1400 hrs & 1400 hrs to 2200 hrs : total 02 nos fgm & 02 nos valve man ( 01 fgm & 01 valve man for each shift of 8 hrs ) , the list of static plants / equipment to be handled and maintained are as below : ( a ) raw water pump house ( i ) monoblock pump set 5 hp = 03 nos ( ii ) lt panels including starter = 03 nos iii ) suction / discharge lines , nrvs sluice valve etc complete ( as per layout inside pump house ) ( b ) clear water pump house room ( i ) centrifugal pump set 75 hp = 02 nos ( ii ) lt panels including starter = 01 nos iii ) suction / discharge lines , nrvs sluice valve etc complete ( as per layout inside pump house ) ( c ) gen set room ( i ) gen set 125 kva = 01 nos ( ii ) lt panel = 01 nos ( iii ) change over switch = 01 nos ( iv ) fuel tank = 01 nos ( v ) lt cable incluiding spare cable ( as per layout site ) , ( d ) filteration plant ( i ) monoblock pump set 5 hp = 05 nos ( ii ) sludge pump set 5 hp = 02 nos ( iii ) alum dozer = 02 nos ( iv ) flacculator including bridge reduction gear , lt panels reduction gear track 01 no ( v ) compressor 10 hp = 02 nosfilter bed = 02 nos ( vii ) chlorome gas plant = 02 nos ( viii ) hypochlorite dozing pump set = 01 nos ( ix ) connected pipes and sluice valve , meters gauges etc ( e ) misc items ( i ) filter plant valves ( ii ) raw water inlet tank valves ( iii ) under ground clear water sump ( iv ) sedimentation tank ( v ) oh reservoirs ( vi ) otm / md accn area water supply lines / valves note : quoted rates shall be deemed to be included for : ( 1 ) operation of all sluice valves for storing and distribution of mass water supply to md accn and troops of klp units situated within 3 km area around the duty premises . ( 2 ) periodical and general maintenance of plant & equipment shall be the responsibility of contractor . cost of minor spare parts deemed necessary for smooth functioning & operation of plant and machinery . , notes : as this item pertain to only wages of labourers based on the prevailing minimum labour wages . hence after opening of financial bid , if it is found that quoted rates are below the existing minimum labour wages rates of semi skilled & skilled labour ( inclusive reliever to operator as per labour wages act ) as prescribed by the government of india / state government / local body ( whichever is higher ) plus cost of other factor such as esi , epf , gst , cost of dress , insurance of operators , safety equipments etc and all factors as specified in tender , then accepting officer at his sole discreption has the right to reject the quoted bid and the same shall be treated as non bonafide . in such case the lowest tender shall be determined by lowest amount amongest valid bonafide bids for acceptance whose rates are found to be reasonable . , manning & operation of water supply installation no 1 for operation of all sluice valves for storing and distribution of mass water supply to md accn and troops of klp units situated within 3 km area around the duty premises including tightening of pump couplings , foundation nut bolts , thimbles of cable , replacement of u / s gland packing , gland ropes etc and also attending the filter bed for wash operation & cleaning of buds / bushes in side the pump house area , cleaning of outside area in 2 shifts of 8 hrs ( i . e from 0600 hrs to 1400 hrs & 1400 hrs to 2200 hrs ) total 02 nos valve man ( 01 valve man for each shift of 8 hrs ) , notes : as this item pertain to only wages of labourers based on the prevailing minimum labour wages . hence after opening of financial bid , if it is found that quoted rates are below the existing minimum labour wages rates of semi skilled labour ( inclusive reliever to operator as per labour wages act ) as prescribed by the government of india / state government / local body ( whichever is higher ) plus cost of other factor such as esi , epf , gst , cost of dress , insurance of operators , safety equipments etc and all factors as specified in tender , then accepting officer at his sole discreption has the right to reject the quoted bid and the same shall be treated as non bonafide . in such case the lowest tender shall be determined by lowest amount amongest valid bonafide bids for acceptance whose rates are found to be reasonable . , general notes applicable for srl item no 1 & 2 of boq: ( a ) contractor will arrange biometric attendance machine by its own expenses at installation and payment will only be made on the basis of biometric attendance . ( b ) reliever for weekly off shall be provided by the contractor at his own cost and rates for the same shall be deemed to included in the quoted rates . no extra payment shall be admissible on this account ( c ) all types of t&p required for day to day reqmt shall be provided by contractor ( d ) all types of transportation if reqd for handling materials / eqpt etc shall be provided by the contractor ( e ) all types of fire eqpts provided in all the installations shall be maintained and operated properly ( f ) all electrical fittings and fixtures to be maintained and contractor shall be responsible for any damage ( g ) all types of water tanks incl flushing tanks shall be maintained . ( h ) all installations to be kept neat and clean all the time and security checks to be carried out daily ( j ) in case of any damage misuse mishandling of govt property , contractor will be held responsible for the same ( k ) all safety eqpts such as breathing apparatus , safety belt , air hose respiratory , portable lighting eqpt , driver suit etc for working hazardous condition to be provided by contractor , ( l ) first aid box with basic medicines to be kept in main installation by the contractor ( m ) misuse of electricity and water to be penalised and effective recovery will be made by the department ( n ) manning and operation shall start as per the stipulated date in work order ( p ) installation shall be kept neat & clean all the time & security of assets shall be ensured ( q ) proper disposal of material of residual dry waste / other waste material should be carried out by the contractor all as directed by engr in charge . the cost of the same is deemed to be included in rates quoted by the contractor ( r ) wages to be paid to employee through individual bank account only duly aadhar linked ( i . e payment through cheque / neft / rtsg ) and documentary proof of payment to tradesmen / operators shall be submitted to the department for releasing of payment . ( s ) minimum i . t . i or any other higher qualification / 05 years experience certificate of all staff employed shall be submitted . ( t ) the rate quoted shall be deemed to including the providing stationery for all above mentioned installations . ( u ) group insurance , e . s . i , and epf shall be provided by the contractor for his staff / tradesmen / operator and documentary proof of payment to tradesmen / opera...

Punjab Water Supply And Sewerage Board - Punjab

22033507 dnit for providing and fixing laying jointing cutting testing of rcc np3 300 mm id pipe and construction of small screen chamber room prov and supply installation of motor pump set sludge pump set repairing of mps and stp complete in dera baba nanak...

Military Engineer Services - Punjab

21887849 manning and operation of water supply installation no . 1 and water supply installation no . 2 at faridkot mil stn , manning & operation of centrifugal pump set / static plants of water supply installation no 2 including tightening of pump couplings , foundation nut bolts , thimbles of cable , replacement of u / s gland packing , gland ropes etc of pump sets or sluice valves , operation of sluice valve , caulking of lead joints of ci pipes in side the pump house or nearby area of water supply no 2 and also attending the filter bed for wash operation & cleaning of buds / bushes in side the pump house area & checking of raw water storage sump and water channel for nallah to new raw water pump house & to storage tank , cleaning of outside area and manning of dg set & other machinery / eqpt in side the pump house in 2 shifts of 8 hrs ( i . e from 0600 hrs to 1400 hrs & 1400 hrs to 2200 hrs : total 02 nos fgm & 02 nos valve man ( 01 fgm & 01 valve man for each shift of 8 hrs ) , the list of static plants / equipment to be handled and maintained are as below : ( a ) raw water pump house ( i ) monoblock pump set 5 hp = 03 nos ( ii ) lt panels including starter = 03 nos iii ) suction / discharge lines , nrvs sluice valve etc complete ( as per layout inside pump house ) ( b ) clear water pump house room ( i ) centrifugal pump set 75 hp = 02 nos ( ii ) lt panels including starter = 01 nos iii ) suction / discharge lines , nrvs sluice valve etc complete ( as per layout inside pump house ) ( c ) gen set room ( i ) gen set 125 kva = 01 nos ( ii ) lt panel = 01 nos ( iii ) change over switch = 01 nos ( iv ) fuel tank = 01 nos ( v ) lt cable incluiding spare cable ( as per layout site ) , ( d ) filteration plant ( i ) monoblock pump set 5 hp = 05 nos ( ii ) sludge pump set 5 hp = 02 nos ( iii ) alum dozer = 02 nos ( iv ) flacculator including bridge reduction gear , lt panels reduction gear track 01 no ( v ) compressor 10 hp = 02 nosfilter bed = 02 nos ( vii ) chlorome gas plant = 02 nos ( viii ) hypochlorite dozing pump set = 01 nos ( ix ) connected pipes and sluice valve , meters gauges etc ( e ) misc items ( i ) filter plant valves ( ii ) raw water inlet tank valves ( iii ) under ground clear water sump ( iv ) sedimentation tank ( v ) oh reservoirs ( vi ) otm / md accn area water supply lines / valves note : quoted rates shall be deemed to be included for : ( 1 ) operation of all sluice valves for storing and distribution of mass water supply to md accn and troops of klp units situated within 3 km area around the duty premises . ( 2 ) periodical and general maintenance of plant & equipment shall be the responsibility of contractor . cost of minor spare parts deemed necessary for smooth functioning & operation of plant and machinery . , notes : as this item pertain to only wages of labourers based on the prevailing minimum labour wages . hence after opening of financial bid , if it is found that quoted rates are below the existing minimum labour wages rates of semi skilled & skilled labour ( inclusive reliever to operator as per labour wages act ) as prescribed by the government of india / state government / local body ( whichever is higher ) plus cost of other factor such as esi , epf , gst , cost of dress , insurance of operators , safety equipments etc and all factors as specified in tender , then accepting officer at his sole discreption has the right to reject the quoted bid and the same shall be treated as non bonafide . in such case the lowest tender shall be determined by lowest amount amongest valid bonafide bids for acceptance whose rates are found to be reasonable . , manning & operation of water supply installation no 1 for operation of all sluice valves for storing and distribution of mass water supply to md accn and troops of klp units situated within 3 km area around the duty premises including tightening of pump couplings , foundation nut bolts , thimbles of cable , replacement of u / s gland packing , gland ropes etc and also attending the filter bed for wash operation & cleaning of buds / bushes in side the pump house area , cleaning of outside area in 2 shifts of 8 hrs ( i . e from 0600 hrs to 1400 hrs & 1400 hrs to 2200 hrs ) total 02 nos valve man ( 01 valve man for each shift of 8 hrs ) , notes : as this item pertain to only wages of labourers based on the prevailing minimum labour wages . hence after opening of financial bid , if it is found that quoted rates are below the existing minimum labour wages rates of semi skilled labour ( inclusive reliever to operator as per labour wages act ) as prescribed by the government of india / state government / local body ( whichever is higher ) plus cost of other factor such as esi , epf , gst , cost of dress , insurance of operators , safety equipments etc and all factors as specified in tender , then accepting officer at his sole discreption has the right to reject the quoted bid and the same shall be treated as non bonafide . in such case the lowest tender shall be determined by lowest amount amongest valid bonafide bids for acceptance whose rates are found to be reasonable . , general notes applicable for srl item no 1 & 2 of boq: ( a ) contractor will arrange biometric attendance machine by its own expenses at installation and payment will only be made on the basis of biometric attendance . ( b ) reliever for weekly off shall be provided by the contractor at his own cost and rates for the same shall be deemed to included in the quoted rates . no extra payment shall be admissible on this account ( c ) all types of t&p required for day to day reqmt shall be provided by contractor ( d ) all types of transportation if reqd for handling materials / eqpt etc shall be provided by the contractor ( e ) all types of fire eqpts provided in all the installations shall be maintained and operated properly ( f ) all electrical fittings and fixtures to be maintained and contractor shall be responsible for any damage ( g ) all types of water tanks incl flushing tanks shall be maintained . ( h ) all installations to be kept neat and clean all the time and security checks to be carried out daily ( j ) in case of any damage misuse mishandling of govt property , contractor will be held responsible for the same ( k ) all safety eqpts such as breathing apparatus , safety belt , air hose respiratory , portable lighting eqpt , driver suit etc for working hazardous condition to be provided by contractor , ( l ) first aid box with basic medicines to be kept in main installation by the contractor ( m ) misuse of electricity and water to be penalised and effective recovery will be made by the department ( n ) manning and operation shall start as per the stipulated date in work order ( p ) installation shall be kept neat & clean all the time & security of assets shall be ensured ( q ) proper disposal of material of residual dry waste / other waste material should be carried out by the contractor all as directed by engr in charge . the cost of the same is deemed to be included in rates quoted by the contractor ( r ) wages to be paid to employee through individual bank account only duly aadhar linked ( i . e payment through cheque / neft / rtsg ) and documentary proof of payment to tradesmen / operators shall be submitted to the department for releasing of payment . ( s ) minimum i . t . i or any other higher qualification / 05 years experience certificate of all staff employed shall be submitted . ( t ) the rate quoted shall be deemed to including the providing stationery for all above mentioned installations . ( u ) group insurance , e . s . i , and epf shall be provided by the contractor for his staff / tradesmen / operator and documentary proof of payment to tradesmen / opera...

Punjab Water Supply And Sewerage Board - Punjab

21839298 dnit for providing and fixing laying jointing cutting testing of rcc np3 300 mm id pipe and construction of small screen chamber room prov and supply installation of motor pump set sludge pump set repairing of mps and stp complete in dera baba nanak...

Central Public Works Department - Punjab

21566798 annual maintenance of sewerage treatment plant at nit jalandhar. sh: procurement of sludge pumps and flow meter and cleaning of tank of stp=> short tender notice...

National Fertilizers Limited - Punjab

21526640 annual repair contract on item rate basis for various jobs in o and u ( prod ) for 2019 20 of nfl , bathinda 1.1 to take out filter media ( sand ) from side stream filters of ct 1 & ct 2 and screen & refill the same or new. approx. quantity 55m3 ( each filter once in a year ) 1.2 shifting of materials & preparation of chemical solution for charging in ct 1 & ct 2 and cleaning of pump house area, decks & basin of ct 1, ct 2 & ct 3 etc. 2.0 resin removal and refilling in the vessel in d.m. plant and cleaning of the area after completion of the job 3.0 removal of activated alumna, screen and refill 4.0 etp shifting and preparation of urea hydrolysis nutrient dose, charging of chemicals, etc. 5.1 manpower requirement for annual shutdown for different jobs in o&u group of plants 5.2 manpower requirement to meet exigency & for smooth running of the plant. 6.1 cleaning of machines in rwfp 6.2 cleaning of channel of reservoirs in rwfp from wild growth / floating material & lifting / disposal the same 7.1 pumping of outside stagnant water in treated water ponds & its disposal on occasional basis in fd area 7.2 cleaning of dewatering pumps’ wells & strainers in fd area 8.0 removal of suspended / floating material etc. from storm water drain trap near etp 9.0 cleaning of machines, equipments, drains including spillage of oil in instrument air compressor house, dm plant, e.t.p. and cooling towers. 10.1 removal of filter media ( sand ) and filling of the same in rwfp ( once in a year ) 10.2 scrapping of filter media sand / topping up of the same in the filter beds in rwfp. 11.1 cleaning of new urea hydrolysis tank & disposal of sludge 11.2 a ) cleaning of chemical pump house. b ) afl pump house. c ) sludge pump house. d ) final effluent pump house. e ) oily waste pump house. f ) urea solution pump house. g ) sludge pump house in rwfp. h ) filtered water pump house in rwfp. i ) cleaning of compr house. j ) new acid waste pump house in dm plant11.3 cleaning of sludge settling pit in etp area ( once in a year ) 12.1 cleaning of clarifiers, including inlet & outlet channel, in rwfp and water washing of the same ( each clarifier once in a year ) 12.2 cleaning of sludge sump and water washing of the same ( once in a year ) 13.1 cleaning of filter water reservoirs in dm plant ( each once in a year ) 13.2 cleaning of new acid effluent sump in dm plant ( once in a year ) 13.3 removal / cleaning / charging of raschig rings of degasser tower ( once in a year ) 14.1 cleaning of cooling tower basin, channel, & sump and top deck in respect of ct 1 including additional cells ( once in a year ) 14.2 cleaning of cooling towers basin, channel & sump and top deck in respect of ct 2 including additional cell ( once in a year ) 14.3 cleaning of cooling towers basin, channel, & sump and top deck in respect of ct 3 ( once in a year ) 15.1 cleaning of acid waste sump and water washing of the same ( once in a year ) 15.2 cleaning of alkali waste sump and water washing of the same ( once in a year ) 15.3 cleaning of chemical waste sump and water washing of the same ( once in a year ) 15.4 cleaning of ammonia stripping tower basin, top deck and water washing of the same ( once in a year ) 15.5 cleaning of ammonia fixed liquor tank and water washing of the same ( once in a year ) 15.6 cleaning of factory sewerage sump and water washing of the same ( once in a year ) 15.7 cleaning of primary clarifier & water washing of the same ( once in a year ) 15.8 cleaning of final clarifier & water washing of the same ( once in a year ) 15.9 cleaning of old urea hydrolysis tank and disposal of sludge removed from the tank ( once in a year ) ...

Punjab Water Supply And Sewerage Board - Punjab

21457564 dnit for prov and fixing laying jointing cutting testing of rcc np3 300 mm id pipe and construction of small screen chamber room prov and supply installation of motor pump set sludge pump set repairing of mps and stp complete in dera baba nanank...

Central Public Works Department - Punjab

20778576 tender for annual maintenance of sewerage treatment plant at nit jalandhar. sh: procurement of sludge pumps and flow meter and cleaning of tank of stp.=> short tender notice...

Central Public Works Department - Punjab

20703559 tender for annual maintenance of sewerage treatment plant at nit jalandhar. sh: procurement of sludge pumps and flow meter and cleaning of tank of stp., tender notification...

Central Public Works Department - Punjab

20678983 tender for annual maintenance of sewerage treatment plant at nit jalandhar. sh: procurement of sludge pumps and flow meter and cleaning of tank of stp....

Department Of Local Bodies - Punjab

18693841 tender for providing installing commissioning of surplus activated sludge pump for 10 mld stp at samana district patiala., ...

Department Of Local Bodies - Punjab

18430474 tender for providing installing commissioning of surplus activated sludge pump for 10 mld stp at samana district patiala., ...

Public Works Department - Punjab

17718148 providing installatoin and commissioning of surplus activated sludge pump of 10 mld stp at samana distt. patiala....

Punjab Water Supply And Sewerage Board - Punjab

17700451 tender for providing, installation and commissioning of surplus activated sludge pump of approved make non clog certical auto coupling sewage, submersible pump 2 hp/i .5 kw. three phase 415v, suitable for delivering 400 lpm at 8 mtr. head, rpm 14 for 10 mld stp at samana, distt. patiala....

Department Of Local Bodies - Punjab

15684455 supply of material for o and m cell, motor control panel / 2018 / 002 / 25 ( 1 nut bolt different size ( superior quality lgalvanised 2 rubber roll 1 kg 3 pvc elbow 1s1 mark 3 4 pvc elbow 151 mark 4 5 gainty handle 6 kassi handle 7 engine handle 8 supply of pvc suction pipe grey in colour heavy duty 3 9 supply of pvc suction pipe grey in colour heavy duty 4 10 cl impellor for kirloskar sludge pumps 11 cl djoint complete with nut bolt & rubber ring cl djoint 10 ( cl 15 ) 12 cl djoint complete with nut bolt & rubber ring cl d joint 12 ( cl 15 ) 13 rope 1 / 2 14 delivery pipe 15 bucket 16 kassi heavy duty 17 construction of chamber for 100mm sluices valve 18 gainty ( heavy duty ) 19 rubber sheet ) ...

Bhakra Beas Management Board - Punjab

11235445 supply , erection , testing and commissioning of self priming horizontal non clog type motor coupled solid handling sewerage / sludge pumps ...

Municipal Corporation - Punjab

11116441 supply of kirloskar make sp 4la self priming sludge pump 100mm coupled with powersmart/kirloskar make 12 hp 1500 rpm twin cylinder handle start air cooled engine with pumps accessories and four wheeler trolley => short tender notice...

National Fertilizers Limited - Punjab

9533980 arc on item rate basis for various jobs in o&u ( production ) 1.1 to take out filter media ( sand ) from side stream filters of ct 1 & ct 2 and screen & refill the same or new. approx. quantity 55m3 ( each filter once in a year ) 1.2 shifting of materials & preparation of chemical solution for charging in ct 1 & ct 2 and cleaning of pump house area, decks & basin of ct 1, ct 2 & ct 3 etc. 2.0 resin removal and refilling in the vessel in d.m. plant and cleaning of the area after completion of the job 3.0 removal of activated alumna, screen and refill 4.0 etp shifting and preparation of urea hydrolysis nutrient dose, charging of chemicals, etc. 5.1 manpower requirement for annual shutdown for different jobs in o&u group of plants 5.2 manpower requirement to meet exigency & for smooth running of the plant. 6.1 cleaning of machines in rwfp 6.2 cleaning of channel of reservoirs in rwfp from wild growth / floating material & lifting / disposal the same 7.1 pumping of outside stagnant water in treated water ponds & its disposal on occasional basis in fd area 7.2 cleaning of dewatering pumps’ wells & strainers in fd area 8.0 removal of suspended / floating material etc. from storm water drain trap near etp 9.0 cleaning of machines, equipments, drains including spillage of oil in instrument air compressor house, dm plant, e.t.p. and cooling towers.10.1 removal of filter media ( sand ) and filling of the same in rwfp ( once in a year ) 10.2 scrapping of filter media sand / topping up of the same in the filter beds in rwfp. 11.1 cleaning of new urea hydrolysis tank & disposal of sludge 11.2 a ) cleaning of chemical pump house. b ) afl pump house. c ) sludge pump house. d ) final effluent pump house. e ) oily waste pump house. f ) urea solution pump house. g ) sludge pump house in rwfp. h ) filtered water pump house in rwfp. i ) cleaning of compr house. j ) new acid waste pump house in dm plant11.3 cleaning of sludge settling pit in etp area ( once in a year ) 12.1 cleaning of clarifiers, including inlet & outlet channel, in rwfp and water washing of the same ( each clarifier once in a year ) 12.2 cleaning of sludge sump and water washing of the same ( once in a year ) 13.1 cleaning of filter water reservoirs in dm plant ( each once in a year ) 13.2 cleaning of new acid effluent sump in dm plant ( once in a year ) 13.3 removal / cleaning / charging of raschig rings of degasser tower ( once in a year ) 14.1 cleaning of cooling tower basin, channel, & sump and top deck in respect of ct 1 including additional cells ( once in a year ) 14.2 cleaning of cooling towers basin, channel & sump and top deck in respect of ct 2 including additional cell ( once in a year ) 14.3 cleaning of cooling towers basin, channel, & sump and top deck in respect of ct 3 ( once in a year ) 15.1 cleaning of acid waste sump and water washing of the same ( once in a year ) 15.2 cleaning of alkali waste sump and water washing of the same ( once in a year ) 15.3 cleaning of chemical waste sump and water washing of the same ( once in a year ) 15.4 cleaning of ammonia stripping tower basin, top deck and water washing of the same ( once in a year ) 15.5 cleaning of ammonia fixed liquor tank and water washing of the same ( once in a year ) 15.6 cleaning of factory sewerage sump and water washing of the same ( once in a year ) 15.7 cleaning of primary clarifier & water washing of the same ( once in a year ) 15.8 cleaning of final clarifier & water washing of the same ( once in a year ) 15.9 cleaning of old urea hydrolysis tank and disposal of sludge removed from the tank ( once in a year ) 16.0 supply of gobar khad in effluent treatment plant for urea hydrolysis...

Bhakra Beas Management Board - Punjab

9064470 supply, erection, testing and commissioning of self priming horizontal non clog type motor coupled solid handling sewerage / sludge pumps for bhakra right bank power house...

Bhakra Beas Management Board - Punjab

8653659 supply, erection, testing and commissioning of self priming, horizontal non clog type motor coupled solid handling sewerage sludge pumps for bhakra right bank power house, bhakra....

Bhakra Beas Management Board - Punjab

8134832 tender for supply, erection, testing and commissioning of self priming, horizontal non clog type motor coupled solid handling sewerage / sludge pumps for bhakra right bank power house, bhakra....

Bhakra Beas Management Board - Punjab

8129871 online tender for supply, erection, testing and commissioning of self priming, horizontal non clog type motor coupled solid handling sewerage sludge pumps for bhakra right bank power house, bhakra....

Punjab Mandi Board - Punjab

6517876 providing of public health services ksb/ kirloskar pumps and motors, filter feed pump, sludge pump, dozing pump for sewage, air blowers, filters, mcc panel electric, sludge d watering system, septic tank with treated water tank and civil work for collecting, providing, installation and testing of effluent treatment plant 50 kld in fish market mehta road....

Government Of Punjab - Punjab

2364364 supply of pneumatic sludge pump easily handles water containing 15 % solids and particulars up to 25mm in size as per specifications....

Government Of Punjab - Punjab

2264111 pneumatic sludge pump easily handles water containing 15% solids and particulars up to 25mm in size....

Department Of Irrigation - Punjab

2185904 pneumatic sludge pump easily handles water containing 15% solids and particulars up to 25mm in size as per specifications....